HT201210 How can solve the 1015 error?

HI...
while i m restoring my iPhone 3gs its not restoring due to some unknown error like 3015. and its not resolvig...
so help me how can i resolving this error...

A 1015 error usually indicates that the iPhone has been jailbroken. Has yours? If so, we can provide no help with jailbroken iPhone in these forums, so you will have to look elsewhere for assistance.
Regards.

Similar Messages

Anyone figure out how to solve the 1015 error

anyone figure out how to solve the 1015 error

Each version of Photoshop has its own installation path therefore a different application as fars as Wacom Configuration. You would need to set preferences for each Photoshop installed on your system. However if you know XML. Wacom Tablet Preference File Utility can save your Wacom preferences into an XML file. That you may be able to duplicate a Photoshop install and the change the Photoshop Path. Or just change the prion version pathe the the new Photoshop path then restore your Wacom Preferences using the modified XML preference file.
Here you see part of my wacom preferences I have set preferences for all Photoshop installed on my workstation.

TS3694 how to solve the 1015 errore

how to solove 1015 errore

Google may provide you some assistance.
Generally that is a sign that the iPhone has been
hacked/modified/jailbroken and, as such, cannot be discussed
here per Terms of Service for these fora.

HOW TO SOLVE THE R6034 ERROR IN ITUNES INSTALATION

I need toknow how to solve the R6034 error in itunes instalation becouse y can´t buk up muy phone

How to solve this ?
#import <UIKit/UIKit.h>
int main(int argc, char *argv[]) {
 NSAutoreleasePool * pool = [[NSAutoreleasePool alloc] init];
 -> int retVal = UIApplicationMain(argc, argv, nil, nil);
 [pool release];
 return retVal;

How to solve the 404 error

Hi,
How to catch or solve the 404 error in application.
Some time we are giving some file name but that file is not avialable at that time it will give 404 error. how to avoid this error.
If 404 error comes i want call some other file. Is it posible.
Thanks Advance.

Yes, this is because IE 5.5 (?) and higher have this wacky "Show friendly HTTP error messages" setting. You can disable this by going to tools -> internet options -> advanced and unchecking "Show friendly HTTP error messages". However as the default IE setting has "Show friendly HTTP error messages" enabled this isn't a good solution.
I believe that if your error page is less than a certain size (in bytes) then IE defaults to it's own error page when "Show friendly HTTP error messages" are enabled. This size is something like 512 bytes or fewer in length.
So basically try making your error page larger (more than 512 bytes in size) and see if that works.

How to solve the emca error

how to solve the warning and severe error....................
[oracle@ip-********* Oracle11g_R2]$ emca -deconfig dbcontrol db -repos drop
STARTED EMCA at Mar 29, 2012 10:20:41 PM
EM Configuration Assistant, Version 11.2.0.0.2 Production
Copyright (c) 2003, 2005, Oracle. All rights reserved.
Enter the following information:
Database SID: testdb11g3
Listener port number: 1521
Password for SYS user:
Password for SYSMAN user:
Do you wish to continue? [yes(Y)/no(N)]: y
Mar 29, 2012 10:22:13 PM oracle.sysman.emcp.EMConfig perform
INFO: This operation is being logged at /u02/oracle/Oracle11g_R2/cfgtoollogs/emca/testdb11g3/emca_2012_03_29_22_20_40.log.
Mar 29, 2012 10:22:13 PM oracle.sysman.emcp.EMDBPreConfig performDeconfiguration
WARNING: EM is not configured for this database. No EM-specific actions can be performed.
Mar 29, 2012 10:22:13 PM oracle.sysman.emcp.EMConfig perform
SEVERE: Listener is not up or database service is not registered with it. Start the Listener and register database service and run EM
Configuration Assistant again .
Refer to the log file at /u02/oracle/Oracle11g_R2/cfgtoollogs/emca/testdb11g3/emca_2012_03_29_22_20_40.log for more details.
Could not complete the configuration. Refer to the log file at
/u02/oracle/Oracle11g_R2/cfgtoollogs/emca/testdb11g3/emca_2012_03_29_22_20_40.log for more details.
[oracle@ip-******* Oracle11g_R2]$ cd

tried but getting the same error.............
[oracle@ip-10-68-199-69 oracle]$ lsnrctl start
LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 29-MAR-2012 23:37:21
Copyright (c) 1991, 2009, Oracle. All rights reserved.
Starting /u02/oracle/Oracle11g_R2/product/11.2.0/dbhome_1/bin/tnslsnr: please wait...
TNSLSNR for Linux: Version 11.2.0.1.0 - Production
System parameter file is /u02/oracle/Oracle11g_R2/product/11.2.0/dbhome_1/network/admin/listener.ora
Log messages written to /u02/oracle/Oracle11g_R2/diag/tnslsnr/ip-10-68-199-69/listener/alert/log.xml
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1521)))
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=localhost)(PORT=1521)))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start Date 29-MAR-2012 23:37:21
Uptime 0 days 0 hr. 0 min. 0 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u02/oracle/Oracle11g_R2/product/11.2.0/dbhome_1/network/admin/listener.ora
Listener Log File /u02/oracle/Oracle11g_R2/diag/tnslsnr/ip-10-68-199-69/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1521)))
The listener supports no services
The command completed successfully
[oracle@ip-10-68-199-69 oracle]$ sqlplus
SQL*Plus: Release 11.2.0.1.0 Production on Thu Mar 29 23:37:34 2012
Copyright (c) 1982, 2009, Oracle. All rights reserved.
Enter user-name: sys/Ashwin
ERROR:
ORA-28009: connection as SYS should be as SYSDBA or SYSOPER
Enter user-name: sys/Ashwin as sysdba
Connected to:
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SQL> startup
ORA-01081: cannot start already-running ORACLE - shut it down first
SQL> shutdown abort
ORACLE instance shut down.
SQL> startup
ORACLE instance started.
Total System Global Area 1603411968 bytes
Fixed Size 2213776 bytes
Variable Size 402655344 bytes
Database Buffers 1191182336 bytes
Redo Buffers 7360512 bytes
Database mounted.
Database opened.
SQL> exit
SQL> exit
Disconnected from Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
[oracle@ip-10-68-199-69 oracle]$ emca -deconfig dbcontrol db -repos drop
STARTED EMCA at Mar 29, 2012 11:55:28 PM
EM Configuration Assistant, Version 11.2.0.0.2 Production
Copyright (c) 2003, 2005, Oracle. All rights reserved.
Enter the following information:
Database SID: testdb11g3
Listener port number: 1521
Password for SYS user:
Password for SYSMAN user:
Do you wish to continue? [yes(Y)/no(N)]: y
Mar 29, 2012 11:55:57 PM oracle.sysman.emcp.EMConfig perform
INFO: This operation is being logged at /u02/oracle/Oracle11g_R2/cfgtoollogs/emca/testdb11g3/emca_2012_03_29_23_55_27.log.
Mar 29, 2012 11:55:57 PM oracle.sysman.emcp.EMDBPreConfig performDeconfiguration
WARNING: EM is not configured for this database. No EM-specific actions can be performed.
Mar 29, 2012 11:55:57 PM oracle.sysman.emcp.EMConfig perform
SEVERE: Listener is not up or database service is not registered with it. Start the Listener and register database service and run EM Configuration Assistant again .
Refer to the log file at /u02/oracle/Oracle11g_R2/cfgtoollogs/emca/testdb11g3/emca_2012_03_29_23_55_27.log for more details.
Could not complete the configuration. Refer to the log file at /u02/oracle/Oracle11g_R2/cfgtoollogs/emca/testdb11g3/emca_2012_03_29_23_55_27.log for more details.

HT201210 how to solve the problem while re storing iphone 3gs. unknon erron occured(29)

How to solve the problem while restoring iphone 3gs? (unknon error occured (29)

Hello Musthafa K.O.M,
Thank you for using Apple Support Communities.
For more information, take a look at:
Resolve specific iTunes update and restore errors
http://support.apple.com/kb/ts3694#47
Check for hardware issues
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the alert when you update or restore, contact Apple support.
Common errors: 1, 10-47, 1002, 1011, 1012, 1014, 1000-1020.
Have a nice day,
Mario

How can solve the problem in email " SMTP Relay "Message rejected" ", how can solve the problem in email " SMTP Relay "Message rejected" "

Dear sirs,
how to solve the mail problem which occurs while I am abroad; bearing in mind that I use HOTSPOT and sometime it's sending emails sometime getting the below messages " SMTP Relay "Message rejected"

The outgoing mail server is rejecting mail from your network address. Typically that happens when your mail service provider is also your ISP, and you connect to it from another network. The SMTP server will allow connections without a password from anywhere, but it will only relay mail from within the ISP's network. It could also be that your account on the server has expired or been suspended.
If you need to send mail from outside your ISP's network, use an independent mail service provider. I don't have a specific recommendation.

How to solve the ASInstance error

hello everyone,
when i install the BIEE11g, I always met a same mistake, that is 'ASInstance install error'. then I lookup the log file, it writes 'ASInstance error, Error in starting opmn server. operation aborted because of a system call failure or internal error'. could you tell me how to solve it?
if i choose to skip the error and continue to install, i could not to visit the http://localhost:7001/analytics and could not succee to run startall command in opmn.
notes: my os is win xp sp3 and database vision is 11.2.0.1.0 and rcu is 1.1.5.0
thank you very much.
regards,
phoeny

hello everyone,
when i install the BIEE11g, I always met a same mistake, that is 'ASInstance install error'. then I lookup the log file, it writes 'ASInstance error, Error in starting opmn server. operation aborted because of a system call failure or internal error'. could you tell me how to solve it?
if i choose to skip the error and continue to install, i could not to visit the http://localhost:7001/analytics and could not succee to run startall command in opmn.
notes: my os is win xp sp3 and database vision is 11.2.0.1.0 and rcu is 1.1.5.0
thank you very much.
regards,
phoeny

[MESSAGE.GENERAL] How can take the actual error text for ABAP proxy error?

Hi...
I'm a ABAPer.
I got to create outbound abap proxy for synchronous server proxy and described below.
My problem is program can not catch the actual error message when occurred error during send data to XI.
The return message is just 'MESSAGE.GENERAL'.
But according to the XI part, 'Key error' is actual reason.
So... how can i take the actual error text like 'Key error'?
* Only MESSAGE.GENERAL is return message for all kind of errors.
Thanks.
Below----
TRY.
 CREATE OBJECT abap_proxy.
 CALL METHOD abap_proxy->execute_synchronous
 EXPORTING
 output = gs_out
 IMPORTING
 input = gs_in.
Exception Handling
 CATCH cx_ai_system_fault INTO go_sys_exception.
 g_sys_result = go_sys_exception->get_text( ).
 CATCH cx_ai_application_fault INTO go_app_exception.
 g_app_result = go_app_exception->get_text( ).
ENDTRY.
COMMIT WORK.
Return status 'D' is succeeded.
if gs_in-sales_group_rer_sap-xstat <> 'D'.
 WRITE:/ 'System Error Message :', g_sys_result.
 WRITE:/ 'Application Error Message :', g_app_result.
endif.
*--Result--
System Error Message : MESSAGE.GENERAL
Application Error Message :
Message was edited by: Miju cho
Message was edited by: Miju cho

Thanks guys, this was useful.
My scenario is for Asynchronous communication.
I guess Fault messages are used in case of Synchronous communication for handling application errors. So if there was something wrong at the JDBC end then I could use the fault messages.
Have i got this right?
I also came across this piece on Acknowledgements. But is says that they can be used with the following Receivers:
The following receivers support acknowledgments:
ABAP and Java proxies (XI 3.0 SP1 for the latter)
Integration processes
IDocs (note that IDocs only return acknowledgments when they have been configured using the ALE audit)
Receiver adapters support system acknowledgments but not application acknowledgments
My Receiver is JDBC. So I guess I cannot use acknowledgements either.
Hence, I need to know what I can do to replicate the system errors eg. failed server etc...so that I can get catch these errors during sending.
I'll tell you abt what happened earlier.
My XI server was down. I executed the code for the sender ABAP Proxy and it did not catch the error. In SXMB_MONI in the R/3 system, I could see the messages queued up. When the XI server started, the messages were transferred to XI.
I need to handle such errors...ie. If the server is down or message did not reach XI then my ABAP program that sends data via ABAP proxy needs to know that something went wrong.
Thanks and Regards,
Ashwin

How to solve the fatal error 1603?

Update installation failed when it run patching files.
It shows fatal error 1603. How can I solve it?

http://helpx.adobe.com/creative-suite/kb/error-1603-install-cs5-products.html

How to solve the bwlow error[urgent]

Hello friends,
I am new to j2me and i am developing an application by parsing the xml file. I am using kxml2 parser for pulling the data. While compiling my appilication i have got the below error. I am using the Wireless Tookit to develop this.
Can any one help me to solve this problem.
Thanks in advance.
C:\WTK22\apps\xmlmidlet\src\XMLMIDlet.java:90: cannot resolve symbol
symbol : class Book
location: class XMLMIDlet
Book book = (Book) bookVector.elementAt(i);
^

The book class does not exist...
The Book class is not part of the kxml2 api... might have something to do with that..

HT201210 How can I resolve Windows Error Msg?

How can I resolve a Windows Error Msg

Make sure the Firewall is turned off in System Preferences / Security - Firewall.
You may have an iTunes shopping cart saved. Launch iTunes then go to the iTunes menu bar click iTunes / Preferences then select the Advanced tab.
Click: Reset warnings and Reset cache
Click OK.
Try disabling any anti virus software you may have installed.
Click here > iTunes: Advanced iTunes Store troubleshooting
Then click "Expand All Sections"
See Error 8003

How to Solve the listerner error?

I install the oracle 8.1.5 server on my computer which operation system is Redhat 6.1
.Now I want to connect to the oracle from another linux computer.But every time I user the command sqlplus scott/tiger@[mytnsname]
it just give me the result :
Error:No tns lisntener.
I found that it's true that when I connect to the oracle server by using the command the listnern will be crupt at the time.
But if I change to a new oracle server which installed on windows NT there are no error.
What's happened? Help me please.
null

<BLOCKQUOTE>quote:<HR>Originally posted by ifonly:
I install the oracle 8.1.5 server on my computer which operation system is Redhat 6.1
.Now I want to connect to the oracle from another linux computer.But every time I user the command sqlplus scott/tiger@[mytnsname]
it just give me the result :
Error:No tns lisntener.
I found that it's true that when I connect to the oracle server by using the command the listnern will be crupt at the time.
But if I change to a new oracle server which installed on windows NT there are no error.
What's happened? Help me please.
<HR></BLOCKQUOTE>
The listener is required at the side of the database only.
On a remote system you have to install teh client software and to set up the network.
The network is mainly setup with installing the software and configuring "tnsnames.ora".
that can be don with vi or 'ORACLE_HOME/bin/netasst.
Try tnsping "connectstring" from the remote system.
Try sqlplus system/manahger@connectstering from remote system.
If that fails, make sure that your listener setup is ok. This can be done with "lsnrctl status". check the output against your client configuration. specially teh area ser vice summary gives you the network name at which the listener listenen for connection attempts.
This service name must be configured as "SID" on the client side. I know a little bit confusing.
null

How to solve the SIGABRT error in Xcode 3 ?

I've built an iOS app and SIGABRT makes it crash . The app uses accelerator . I use the latest version of Xcode 3 (3.2.6) . How to sovle the problem ?

How to solve this ?
#import <UIKit/UIKit.h>
int main(int argc, char *argv[]) {
 NSAutoreleasePool * pool = [[NSAutoreleasePool alloc] init];
 -> int retVal = UIApplicationMain(argc, argv, nil, nil);
 [pool release];
 return retVal;

HT201210 How can solve the 1015 error?

Similar Messages

Maybe you are looking for