HT201210 My IPAD will not do anything. It just has a picture of a usb with an arrow pointing to an itunes logo. How do I fix this?
Why will my ipad not update?
You need to restore the iPad now. When you restore the iPad, the newest iOS should download and install to the device.
Read this for more information.
http://support.apple.com/kb/ht1414
Similar Messages
-
my will not do anything and it has a picture of the usb cable and the itunes logo on the screen
Your iPhone is telling you you need to restore it using iTunes on a computer. Follow the instructions below.
Use iTunes to restore your iOS device to factory settings - Apple Support -
I just bought my iphon last night & tried doing it`s first update this morning. I got an error message that the update failed & now my iphone only shows a pic of a usb cable with an arrow pointing to the itunes logo.
I already tried holding down the on off buton & the home button like the instructions say. Problem is that when the instructions say I should be at the part where itunes is again recognizing my iphone, my itune is not recognizing my iphone. So I am stuck. I follow the instrustions, but the resluts are different, so I can`t continue to the next step. Very frustrated, as the nearest Apple store is over an hour`s drive away.Open iTunes on computer. Connect iPhone to computer. Hold both home and power buttons until iTunes recognizes iPhone in Recovery Mode. Usually takes about 20 seconds of holding both buttons. Restore the Firmware. If the process Errors again, write down the error message and error #, on paper so you can solve the problem. If there are serious problems, all iPhone 4S have full warranty coverage with Apple.
-
Hi, I bought an iPod 2 and I jailbreaked it before. I tried to download the iOS 5.0.1 from the Settings icon on my iPad 2 but then my iPad wouldn't turn on anymore and it kept on showing a screen with an arrow pointing to an iTunes symbol. I later learned that this was the recovery screen so I tried to put it out of the recovery mode by pressing the home button and power button simultaneously, but the screen kept on returning back to the recovery screen. I could not restore the iPad 2 on iTunes either, so I downloaded Tiny Umbrella 5.10.01 and tried to save the shsh. However, under the recovering devices section on the left side, my iPad did not appear and I only got a device titled ?18092..... I tried to save the shsh of this ?18902... anyways but this did not work. So, I clicked on the device and pressed the exit recovery but then my iPad2 screen went black with a white apple logo in the middle. This logo keeps on dimming and disappearing and even when I plug my iPad 2 to the computer, neither my iTunes nor the Tiny Umbrella notice it. I need urgent help!
eddiekero wrote:
Hi, I bought an iPod 2 and I jailbreaked it before. I tried to download the iOS 5.0.1 from the Settings icon on my iPad 2 but then my iPad wouldn't turn on anymore and it kept on showing a screen with an arrow pointing to an iTunes symbol. I later learned that this was the recovery screen so I tried to put it out of the recovery mode by pressing the home button and power button simultaneously, but the screen kept on returning back to the recovery screen. I could not restore the iPad 2 on iTunes either, so I downloaded Tiny Umbrella 5.10.01 and tried to save the shsh. However, under the recovering devices section on the left side, my iPad did not appear and I only got a device titled ?18092..... I tried to save the shsh of this ?18902... anyways but this did not work. So, I clicked on the device and pressed the exit recovery but then my iPad2 screen went black with a white apple logo in the middle. This logo keeps on dimming and disappearing and even when I plug my iPad 2 to the computer, neither my iTunes nor the Tiny Umbrella notice it. I need urgent help!
At this point only a restore will fix your issue. -
My iPad is. "Frozen"... Graphic of charger cord connector with an arrow pointing to the iTunes logo. This happened when I was updating iOS software.
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY. -
Was setting up my ipad, turned it off. Came back turned it on and after you select ur country step it came up with "connect to itunes" logo, how do i fix this? And i dont have a computer.?!
Reboot the computer then try placing the iPod in Recovery mode and then restoring via iTunes.
Next try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
HT201412 ipad will not do anything but show apple icon ?
ipad will not do anything but show apple icon help please ?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
my iPad will not auto-connect to my network. I need to type in a security key each time. Is there a way aound this?
ThanksSome things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
My ipad will not charge up. it just shows the red battery signal and then switches off
my ipad will not charge up. it just shows the red battery signal and then switches off. The same charger succesfully charges other idas so i know it is no the charger that is faulty.Any suggestions
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
iPhone: Hardware troubleshooting (Power/Battery section also applies to iPad)
http://support.apple.com/kb/TS2802
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
iPad: Charging the battery
http://support.apple.com/kb/HT4060
Best Practices for iPad Battery Charging
http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
Cheers, Tom
BTW- Your profile shows you have iOS 6.1.4 installed. The max iOS for an iPad is 6.1.3. iOS 6.1.4 is for iPhones only. -
My MacBook Air 13' (2013) will occasionally start the fan at full blast, not connect to any wifi or detect any wifi, and will remove the battery icon from my menu bad as well as tell me there is no battery connected. How do I fix this? I have restarted my computer multiple times, **** it down, and ran a diagnostic test to tell me nothing is wrong and my computer is not running any applications. There is no reason for the fan to be on full blast! when I try to set the option to show my battery icon in the menu bar, it will automatically uncheck. How do I fix all of this?
Have you tried SMC and PRAM resets?
http://support.apple.com/kb/HT3964
http://support.apple.com/kb/ht1379
Ciao. -
I attempted to update to latest version of IOS. Now all I get on the display is a graphic of the power cord with an arrow pointing to an iTunes icon. Ipad does not seem to power down or power up correctly. Home button is not responding.
I am new to this, could you provide me with a little more detail on how to do this? Thanks so much!
-
I recently reinstalled iTunes, and now it won't recognize my iphone so I'm not able to sync the phone with iTunes. How do I fix this?
It has been shown there are problems with the latest update of iTunes and Windows computers. What you need to do is remove and reinstall iTunes, and make sure that you follow the steps in this support document exactly. http://support.apple.com/kb/ht1923. If you do not follow them exactly, you will just compound your problems. Once you do this, you should have no trouble having the phone recognized in iTunes.
-
I bought a new ipad2 yesterday and charged the battery and then expected to get going with it but the screen only displays an image of a ubs connection with an arrow pointing to a itunes symbol. I downloaded itunes on a PC and plugged in the ipad to it but nothing changed on the PC or ipad. very frustrating. anyone else experience this or have know how or ideas to help me?
Here is my standard reply, some of which may have no relevance to your situation. Start with trying different USB ports, even a numbe of times.
1. Make sure that your device is not hidden (left hand pane). If it just reads device then toggle between SHOW and HIDE.
2. Try all the other ports on your computer, even a number of times.
3. Make sure your lead /connections are not faulty.
4. If you have another computer try plugging your device into it without taking any action, give it a moment, remove it and try it back in your other computer again.
5. Make sure you have the latest version of iTunes installed.
6. If using Widows, make sure all Windows Updates are installed.
7. Failing all that, see here - http://support.apple.com/kb/TS1538 for Windows and http://support.apple.com/kb/TS1591 for Macs
8. And failing all that put the device into Recovery mode. See here and note the paragraph 'If you restore from a different computer.... ' down near the bottom of the page -
http://support.apple.com/kb/HT1808 -
Ok so I am having issues with charging my iPad as well. So I took advice from this forum and yes, if you turn the brightness down my iPad charges. Thanks Apple I just went and spent money on a new charger I didn't need. Really you need to fix this issue.
Wow. Okay...
I'll let the real veterans in this forum tackle your issues one after the other. But, I can tell you, all will be well.
My only comment would be re: your computer specs:
BJReis wrote:
. This may be due to somewhat older equipment:
GHz Intel Core Duo MacBook Pro with a 4GB memory computer with Ddr3 running OSX 10.8.4
To be completely honest, FCPX is a RAM hog. It just is. But, RAM is relatively cheap, and the pay-off is good.
4GB is right on the edge, IMHO. 16G is ideal.
I wish you luck, hang in there, and standby for more help. -
I tried to upgrade to ios4 by plugging my Ipad into Itunes on my desktop. I got an error message as it was downloading. Now my Ipad won't turn on at all. All I get is a pic of the plug and an arrow pointing to the Itunes logo. I tried to reset, but nothing works. When I try to plug the Ipad into my desktop and access Itunes, my Ipad doesn't show up on the Itunes screen.
You need to restore your iPad using recovery mode and the process is covered in this article.
iPad: Unable to update or restore.
http://support.apple.com/kb/ht4097
Maybe you are looking for
-
Do you have any question for us?
At the end of interview most employer as this, what could be question to ask to for good impression on Oracle DBA interview?
-
Can't add text to photo. text doesn't appear when typeing.
I can't add text to photo. The Horizontal Text Box appears but when typing there is no text seen. There is a cursor line which appears outside the text box.
-
Running a 9.2 managed server as a windows service
Is it possible to run a WebLogic 9.2 managed server as a windows service? I was able to get the AdminServer to run as a service, but not my managed server. I am not using Node Manager. Should I be? Please help...
-
My iPhone 5 earpiece is not working
my iPhone 5 earpiece is not working.. i can only hear through my speaker or if i plug in my headphones...does anyone else have this problem and can anyone help me??
-
Assign container with value of another container
Hello, I would like to assign the parameter (defined as referenced container) of a subsequence with the value of another container. Something like this: "Parameters.OUT_CONSTANTS = FileGlobals.CONSTANTS" But in my expression windows, I get the messag