HT201210 when i try to restore my ipod touch, after i go through the steps then a pop up says that it cannot be restored, what do i do?
my ipod touch says plug it into itunes, so i do. then it doesnt recognize my device, then it says its in recoverey mode and needs to be restored, so i restore it and after i do a pop up comes up and says that an unknown error has occured and cannot be restored, what do i do?
and when its trying to be restored the plug does the sound that plays during when you plug an ipod in and out... i dont know what to do please help me
Error 9
This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if the device is manually disconnected during the restore process. This issue can be resolved by performing USB troubleshooting, using a different USB dock-connector cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
from:
http://support.apple.com/kb/TS3694#error9
Similar Messages
-
i need help asap because i keep getting kicked off of facebook and twitter because of the update in the software.
On the computer go to iTunes>Preferences>Devices and select the backup and click on delete.
For more information see:
iOS: Troubleshooting backup issues in iTunes -
when i try to reset my ipod it stops at 10minutes and the ipod turns itself on and acts like ive done nothing to it, it has been stuck on the "connect to itunes screen" and it wont reset. why?
After you place the iPod in recovery mode using
iOS: Unable to update or restore
You have to then connect the iPod to your computer and restore via iTunes. Are you doing that? -
what do i do when i try to sync my ipod touch to itunes and it shows me an error message that the sync session failed to start?
Hello brainiac08
Typically that error occurs because of a backup issue. Check out the article below to resolve it.
iOS: Troubleshooting backup issues in iTunes
http://support.apple.com/kb/ts2529
Thanks for using Apple Support Communities.
Regards,
-Norm G. -
When I try to update my iPod Touch, I get an error message saying "The iPod Software update server could not be contacted. Make sure your network settings are correct and your network connection is active, or try again later." Has anyone else had that and how do you end up updating your iPod?
Update Server
Try:
- Powering off and then back on your router.
- iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
- Change the DNS to either Google's or Open DNS servers
Public DNS — Google Developers
OpenDNS IP Addresses
- For one user uninstalling/reinstalling iTunes resolved the problem
- Try on another computer/network
- Wait if it is an Apple problem -
When I try to update my iPod touch to iOS4.3 I'm told to go to Devices in iTunes, then Summary. I can't find Summary.
If you have iTunes 11 turn on the Sidebar. Go to iTunes>View and click on Show Sidebar. You can also do a Crtl+S to show the sidebar. The sidebar is where Devices appears. and Control+B to show the Menu bar
Are you sure you really do not have a 2G iPod? Those can only go to 4.2.1
Identifying iPod models
iPod touch (3rd generation)
iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318. -
When I try to update my iPod touch, a message saying there isn't enough space on my computer appears and all media on my iPod will be lost, should I proceed with the update?
My iTunes Library is on my computer, I have done a backup manually, and all of my music is on an external hard drive (as well as my iTunes library).Thanks a lot Recycle bin is empty, I will move some files from the C drive to an external hard drive, then do the update, and then move the files back. Any files you recommend not moving to the external hard drive at all?
-
Why do I keep getting a message that my ical is not connected when I try to sync my ipod touch with my mac book?
It sounds as if your account has been compromised. I would recommend logging into those accounts from your computer and their websites and changing your password.
-
When i try to sync my iPod Touch 4th Gen. it gives me an error message #1150. help?
when i try to sync my iPod Touch 4th Gen. it gives me an error message #1150. help?
Try:
iTunes Error 1150 while syncing music...: Apple Support Communities
Then try the previous discussions listed on the right side of this page under the heading More Like This. -
When I try to sync my iPod nano, it opens up driver E and then nothing happens
When I try to sync my iPod nano, it opens up driver E and then nothing happens.
I have searched all over for troubleshooting help.
Doublechecking. In the course of your troubleshooting to date, have you worked through the following document?
iTunes: Error 13019 during sync -
When I try to update my iPod touch I get a message that the iTunes is already upgraded. My iPod is 4.1
Do you have a 2G, 3G or 4G iPod?
A 2G can go to 4.2.1
A 3G and 4G ro 5.1
Identify yours yours here:
Identifying iPod models
Do you have iTunes 10.6 on the computer?
What computer OS and version do you have?
If a Mac OSX 10.4.11 you need to update to t least 10.5.8. With 10.4.11 you can only go to iTunes 9.X and going beyond 4.1 requires 10.X -
when i try to sync my ipod touch it will tell me there is not enough megabites but i still have 3.1gb open
Either sync less or delete some media from your iPod. You are trying to sync mor that 3.1 GB to the iPod.
-
Transfered my music & video library from my laptop to my PC. Syncing my ipod classic and my ipad without incident to the PC. But when I try to sync my ipod touch, the only thing that will sync is music that I have purchased on that PC. Any ideas?
where on my computer am I suppose to make the individual picture files and have them to upload on my ipod touch.... I do have a photo library on my computer, but in the photo tab in itunes for the ipod touch and there is nothing checked for syncing, cause when I do check it it always says its going to replace everything i have in my photo library on my ipod touch..... So how am i suppose to have it checked and have it NOT replace pictures on it????
Also I cannot make more photo albums into my ipod touch, it just replaces the one album every time....
I am very frustrated cause I have tried the manuals and the apple support help etc and nothing pertains to my exact issue.....
Please if u could elaberate I would appreciate it alot.....
thank u -
My ipod touch is disabled, i installed the latest version of itunes, but cant figure out how to restore the ipod, can anyone help?
If you run into the "another installation" message even after the reboot of the PC (which is an excellent idea by HTP ProXy), reregistering your Windows Installer Service is worth a try.
First, launch a command prompt as an administrator. In your Start search, type cmd then right-click on the cmd that comes up and select "Run as administrator".
At the command prompt:
Type %windir%\system32\msiexec.exe /unregister and hit enter.
Type %windir%\syswow64\msiexec.exe /unregister and hit enter.
Type %windir%\system32\msiexec.exe /regserver and hit enter.
Type %windir%\syswow64\msiexec.exe /regserver and hit enter.
Restart the PC and try another reinstalll. -
I am not able to restore neither from iTunes nor from iCloud. The proble with iTunes is it says that the backup is corrupted or incompatible. And I am not able to connect to iCloud for restoring. I have IOS 7.0.4 when I have taken the backup.
iCloud does not connect and it says Request Timed out.
Not Sure how to restore my iPad.
Please help!!
Thanksmy problem is with I cloud not iTunes what's up with apple haven't they got the brains to sort out this prob, that they have to let the "community " know instead of helping to fix the problem without having to go through all the hassle of signing in writing a small blog & then leaving it until someone bored with time to write their blog to at some point fix the prob or not ! oh nearly forgot my prob like
HRESULT:0X80070570 no clear explanation as to what this means or why in plain English for the not techno phoebes
Maybe you are looking for
-
How to include the variable as a part of the sqlStatement in doGet Servlet
How can I get the variable empnum as a part of the sqlStatement. I am getting an error. String empnum = req.getParameter("empnum"); --Works out.println("THE empnum IS : " + empnum); -- Works String dsJndi = "jdbc/OracleCoreDST"; -- Works String sqlSt
-
Advantages of using higher version of catalog Database.
Hi Gurus, Wanted to know what are the advantages of using higher version of catalog database. for ex: my target database is 10.2.0.4 and catalog database is 11.2.0.1
-
Document of upgrade in ecc 6.0
Dear all, Anybody have any document for ECC 6.0. Because our company is going to upgrade to ecc 6.0. Pls. sent any material on my mail id [email protected] regards Amit
-
Lost music! Need help.
-
Force in labview the variables of a PLC
Hi, I want to make a simulation in labview. I have a PLC connected to labview through OPC. I have a lamp and a switch in the front panel in labview and I want to click the switch to force the input in the PLC and the PLC, due to the program that it h