HT201250 Anyone have time machine "lock up" while backing up and not completing the task?

I have the drive connected for over 24 hrs and time machine will only back up 25% of the 75Gb it claims to need to back up.
I have re tried and get the same result, and T.M. will show "backing up" even after 24 hrs.
I know it is not the drive being too full or being defective, since a partition set up for a pc works just fine.

Hi, many people have, but I think you need to Repair the TM Partion, & maybe your Boot drive, maybe more.
Have you looked through Pondini's extensive TM help site?
http://Pondini.org/TM/FAQ.html
http://pondini.org/TM/Troubleshooting.html
Can't imagine something not being covered there.

Similar Messages

Time Machine spends hours partially backing up and then fails with "Time Machine couldn't complete the backup due to a network problem." Tried suggestions I've seen on the forum.

Time Machine spends hours partially backing up and then fails with "Time Machine couldn't complete the backup due to a network problem." I've tried various suggestions I've seen on the forum but nothing has worked. TIme Machine worked fine for the last two years and just suddenly started having this problem every time. The only thing that was a little different is that the computer was off for a week while on vacation and then I added a large amount (20 GB) of photos. Now the requested backup size is 82GB, which is large, and process proceeds very slowly for 2-3 hours before failing with the message mentioned. I have more than enough available backup storage space for it. Before failing, Time Machine has backed up no more than 12GB or so of the backup. It fails during different files each time.
I've turned off the computer sleep feature, and I've checked that the NAS is set to never automatically power down. I normally backup over Wi-Fi, but I've also tried connecting to Ethernet and it still has the same problem. It's odd because I also have a MacBook Pro that is still backing up fine to the same NAS using the MacBook's Time Machine.
I am using an iMac with OS X 10.6.8 and an Iomega StorCenter ix2-200 NAS.
I have system logs that I can share if helpful. The logged messages vary a bit from run to run, but here are some messages that I've been seeing:
I always get this message near the beginning of the backup:
Event store UUIDs don't match for volume: Macintosh HD
I've gotten this messsage a number of times:
Bulk setting Spotlight attributes failed.
One Day
Stopping backupd to allow ejection of backup destination disk!
Another day
1/7/12 10:44:20 AM
mDNSResponder[18]
PenaltyTimeForServer: PenaltyTime negative -112916, (server penaltyTime -1132397006, timenow -1132284090) resetting the penalty
1/7/12 10:46:37 AM
kernel
ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 0 on so 0x1106be94
1/7/12 10:46:37 AM
kernel
AFP_VFS afpfs_DoReconnect started /Volumes/TimeMachine prevTrigger 0 currTrigger 1
Another Day
1/6/12 8:03:22 AM
Google Chrome[164]
Cannot find function pointer CMPluginInFactory for factory 3487BB5A-3E66-11D5-A64E-003065B300BC in CFBundle/CFPlugIn 0x16f99e20 </Users/smarmer/Library/Contextual Menu Items/Google Notifier Quick Add CM Plugin.plugin> (not loaded)
1/6/12 8:04:02 AM
com.apple.backupd[193]
Copied 7.5 GB of 67.0 GB, 8866 of 8866 items
1/6/12 8:06:58 AM
/System/Library/CoreServices/CCacheServer.app/Contents/MacOS/CCacheServer[1013]
No valid tickets, timing out
1/6/12 8:29:44 AM
mDNSResponder[19]
PenaltyTimeForServer: PenaltyTime negative -148702, (server penaltyTime 2056822773, timenow 2056971475) resetting the penalty
1/6/12 8:59:22 AM
kernel
ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 0 on so 0xa5ac380
1/6/12 8:59:22 AM
kernel
AFP_VFS afpfs_DoReconnect started /Volumes/TimeMachine prevTrigger 0 currTrigger 1
1/6/12 8:59:22 AM
kernel
AFP_VFS afpfs_DoReconnect: doing reconnect on /Volumes/TimeMachine
1/6/12 8:59:22 AM
kernel
AFP_VFS afpfs_DoReconnect: soft mounted and hidden volume so do not notify KEA for /Volumes/TimeMachine
1/6/12 8:59:22 AM
kernel
AFP_VFS afpfs_DoReconnect: Max reconnect time: 30 secs, Connect timeout: 15 secs for /Volumes/TimeMachine
1/6/12 8:59:22 AM
kernel
AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/TimeMachine
1/6/12 8:59:22 AM
kernel
ASP_TCP asp_SetTCPQoS: sock_settclassopt got error 57
Another day
1/5/12 3:48:55 PM
mdworker[2128]
CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary.
1/5/12 4:24:54 PM
mDNSResponder[19]
PenaltyTimeForServer: PenaltyTime negative -42698, (server penaltyTime 1148718961, timenow 1148761659) resetting the penalty
1/5/12 4:29:58 PM
com.apple.backupd[2074]
Copied 586.4 MB of 67.0 GB, 9891 of 9891 items
1/5/12 4:39:00 PM
kernel
ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 0 on so 0xa1c0380

bokon0n wrote:
1/11/12 8:53:30 AM
com.apple.backupd[1169]
Warning: Destination /Volumes/TimeMachine does not support TM Lock Stealing
1/11/12 8:53:30 AM
com.apple.backupd[1169]
Warning: Destination /Volumes/TimeMachine does not support Server Reply Cache
Those indicate that your NAS is not fully compatible with Snow Leopard.
1/11/12 8:53:35 AM
kernel
jnl: disk2s2: replay_journal: from: 67182592 to: 78680064 (joffset 0xa7b8000)
1/11/12 8:53:39 AM
kernel
jnl: disk2s2: examining extra transactions starting @ 78680064 / 0x4b09000
1/11/12 8:53:39 AM
kernel
jnl: disk2s2: Extra txn replay stopped @ 79056896 / 0x4b65000
1/11/12 8:53:49 AM
kernel
jnl: disk2s2: journal replay done.
1/11/12 8:53:49 AM
fseventsd[41]
event logs in /Volumes/Time Machine/.fseventsd out of sync with volume. destroying old logs. (253512 14 253512)
1/11/12 8:53:50 AM
kernel
hfs: Removed 1 orphaned / unlinked files and 0 directories
That looks like a problem was found with the file system (data) on the TM disk. I don't know the details, but OSX tried to recover it from the journal, and found extra data on the drive. Likely a result of the incompatibility mentioned above.
1/11/12 9:47:40 AM
com.apple.backupd[1169]
Bulk setting Spotlight attributes failed.
That's a problem writing to the NAS drive.
But the backup continued after all this.
1/11/12 1:25:07 PM
kernel
ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 0 on so 0x9d00b44
Something caused a disconnect. Can't tell from the log what it was.
I doubt it's a problem with something in OSX being damaged or corrupted, but reinstalling OSX isn't a major hassle, so might be worth a try.
To be incompatible with Snow Leopard, this NAS must be at least a couple of years old. It may be beginning to fail.
Contact the maker. See if there's an update to make it compatible with Snow Leopard. If so, that might fix it.
If not, or if that doesn't fix it, see if they have any diagnostics that will shed any light.

Ow can I use my time capsule as a time machine backup without using it wirelessly and not as a wireless router?

How can I use my time capsule as a time machine backup without using it wirelessly and not as a wireless router?

bzb888 wrote:
I have a wireless transmitter already, would like to use the capsule just as a back up drive, I tried hooking up from the ethernet port on the imac to the one of the ports on the capsule but then my Wifi would not work. do I hook the cable to the port with the circle or the arrows?
It is better to have the TC as part of the main network in bridge. You do not need to run wireless.
If you want to use the TC plugged in by ethernet and still use wireless for internet, that is possible but the setup is rather more complicated.. the computer must not get confused about which device to use as a gateway or dns server.
See info in this thread on setting this up.
https://discussions.apple.com/thread/4817218?tstart=30
I need to add.. a USB drive would be cheaper, faster and more reliable. It is really poor use of a TC.

I recently took my imac in for a recall on the hard drive, they replaced my hard drive, i used time machine to restore all my files. Now when I turn time machine on it says back up failed not enough space, it is not overwriting old back ups.

I recently took my imac in for a recall on the hard drive, they replaced my hard drive, i used time machine to restore all my files. Now when I turn time machine on it says back up failed not enough space, it is not overwriting old back ups. Why? Please help

http://pondini.org/TM/FAQ.html

Time Machine Restore Finishes But Wont Boot And Not Enough Restored

I have just had need to restore my MacBook from my Time Machine backup of yesterday.
Basically I boot from the Leopard DVD, Select Restore and pick the date/time of the backup.
Restore start and finishes OK (if a little short on time I noticed) but on first boot the MacBook crashes and displays a message saying the Mac needs powering off/on.
After this the MacBook will not boot again and displays the same message.
If I boot off the DVD and run disk utility I see only 40gb or so used on the disk when my machine is around 150gb.
I have tried a number of restores going back a day each time and each restore produces the same result.
Can someone please give me some suggestions as to how I might successfully restore from the backup.
If I can't is it possible to reinstall Leopard fresh and then connect the Time Machine drive to the restored system and view the backup from there ?? If so how please.
Many thanks in advance. I can feel a very sleepless night ahead of me.
Kind Regards and Seasonal Greetings
NIALL8-(

Niall Mallyon wrote:
I have browsed the time machine drive both from within finder and iPhoto and the backups appear very irratic.
Have you done a +*Repair Disk+* on your TM drive, per #A5 in the Time Machine - Troubleshooting *User Tip,* also at the top of this forum?
My confidence in Time Machine has taken a severe dent here so I am now going to be taking manual backups of all my data, itunes and photos on a regular basis as well as continuing to use the iPod for storage.
Consider what many of us do: keep a completely separate, independent backup in the form of a "bootable clone" via CarbonCopyCloner (which I use) or SuperDuper, in addition to full TM backups. You might even want to get a portable external HD for this, so you can take it to a secure off-site location. (I learned long ago, usually the hard way, not to trust my backups 100% to any single app or hardware.) And there was a thread just a couple of weeks ago where a full restore had nearly completed when BAM! the TM drive failed!
Just wish I could understand where things went wrong in the first place so I can ensure it doesn't happen again. I'll be sure to browse time machine regulalrly from now one to check things.
From your description of what you see in your backups, it's hard to tell what might have caused this very unusual situation. Something may have gone wrong with one of the previous restores, or there is/was hardware problems with one of the drives, or some sort of OSX problem.

I have my MacBook 13' (2006) backed up on Time Machine. I just replaced the hard drive. How do I access the Time Machine to resotre my files, setting and programs on the new HD?

I am running Snow Leopard and have my old files isolated in a new folder on the laptop, but I want to restore the old settings, programas, etc. from the Time Machine. TM is currently backing up the new HD as if it were a new computer.

Instead of using Time Capsule or Time Machine to access the archived backup, use Migration Assistant to restore the backup from Time Capsule. Worked like a charm.

Time Machine hung up while "backing up"

Time Machine's first attempt at a back up failed this morning. And as this has happened before, I simply did what I had done in the past ... a manual "back up now". But today, it didn't work. Instead, the Time Machine preferences states that it is "backing up" and seems to get hung up like that. When you check the TM Buddy widget, the following line is listed over and over 10-15 times ...
Waiting for index to be ready (915 > 0)
TM has been hung up for hours ... seriously hours ... like this. I've manually stopped the back up, restarted the computer, etc. all to no avail. And now when I've tried to b/u, my widget displays nothing. So, I don't even have anything to post to aid in assistance. TM is currently turned off.
Any help on where to go from here is greatly appreciated.

Hjeirce wrote:
Waiting for index to be ready (915 > 0)
Hi, and welcome to the forums.
This can be caused by several things.
First, are you sure it's formatted properly? Use Disk Utility (in your Applications/Utilities folder). Select the top line (with the make and size). Down towards the bottom, *Partition Map Scheme* should be GUID for an Intel Mac, +Apple Partition Map+ for a PPC Mac.
Then select the second line. Down towards the bottom, Format should be +Mac OS Extended (Journaled)+
If you're running any anti-virus scans, exclude your TM disk from them.
Also exclude it from Spotlight, at least temporarily, via System Preferences > Spotlight > Privacy.
If those don't help, that leaves the drive itself:
Is it FireWire or USB?
If USB, does it have it's own power supply, or does it get power from your Mac? If it uses your Mac's power, try another port (not one on your keyboard), and try unplugging other USB devices such as printers.
The drive may be "spinning down" at idle. Try System Preferences > Energy Saver and de-select +Put the hard drives to sleep ...+ Some drives respond to that setting, some don't.
Does it have an automatic "Spin down" mode of it's own? If so, can you disable it? Check with the manufacturer's web site, support, and/or forums. Some WD drives, I think, have a recent firmware update that may fix this.

TS3048 My OSx system froze while backing up and since then The keyboard won't operate and I have a password and so can't access the OS now can anyone help.

My computer froze during a back up and since then I cannot access system because the keyboard doesn't work at all and the computer is password protected. Can anyone help please?

You may need a wired keyboard to carry out some of these steps. It's a good idea to keep a cheap wired keyboard and mouse or trackball as backups for a desktop Mac anyway, because Bluetooth isn't completely reliable.
Step 1
Follow the instructions in these support articles:
How to set up your Apple Wireless Keyboard
Apple Wireless Keyboard: Difficulty during pairing process
Bluetooth devices become unresponsive
Step 2
The keyboard should pair automatically when you reboot. You may have to press and hold the power button on the right side of an Apple keyboard until the LED starts flashing.
Step 3
Reset the System Management Controller.
Step 4
Back up all data.
Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/com.apple.Bluetooth.plist
Right-click or control-click the line and select
Services ▹ Reveal
from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Reboot.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combinationcommand-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
Step 5
See these support articles:
Bluetooth keyboard may not pair during Setup Assistant
Wi-Fi and Bluetooth: Potential sources of wireless interference
Bluetooth: Unreliable wireless performance may occur when USB 3.0 external devices are close
Step 6
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

I'm operating CS5 on iMac 10.10.2..Q. The last two or three times I have tried to use "Merge to HDR Pro" it will not complete the task and closes down. How do I fix it...I have restarted the system but no help...RDGS, Mike Frey

I 'm operating CS5 on iMac 10.10.2.....Q.the last two or three times I have tried to use "Merge to HDR Pro" the aplication quits with no image...I have restarted the system which does not solve the problem.

Details about your setup, please.
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
A screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Anyone have a fix for a USB HP TV tuner not waking the laptop to record? Records fine while awake.

HP Pavillion DV7 running Windows 7 64-bit
There have been multiple windows updates since using this tuner.

captainclipper wrote:
I have an HP DV7-1451 laptop running windows 7. I am using an HP usb tuner. After downloading some drivers the tv tuner worked fine. Now it doers not work at all. Whenever I load window media center to reconfigure the tuner, I get back a message that there is no signal. Has anyone experienced this problem? Has the tuner become defective? Are there other drivers thet need to be downloaded? Do I need a signal amplifier? Also, I noticed the tuner is very warm to the touch.
Thanks
captainclipper,
Hey, was just looking through some older forums and saw that this one was never replied to. Are you still having issues with the HP tuner? If so, the underlying cause could be any number of reasons from software to hardware to the signal the tuner is looking for. As it currently stands, without a digital converter, you will only get local channels 1-49. And this will only be until around spring when all analog channels are removed completely. In any event, I know that the HP software looks for multiple signals (digital vs analog). If you're not using a digital antenna then you'll want to make sure it's tuning to the Analog NTSC tuner.
Hope this helps.
Regards,
Chris
Christian
Verizon Telecom
Fiber Solution Center
Notice: Content posted by Verizon employees is meant to be informational and does not supercede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

Does anyone have time for this one? photoshop 2014 gradient not working.

Working on a project with photoshop 2014 updated thursday night using foreground to transparent gradient. The edges of the picture are staying white instead of being transparent over the background or other pictures. I thought I was using the gradient correctly converting the pic to a png file, setting the mask, then applying the gradient to the edges. Is there something I am missing??? Please help.

below is a snip of the effect i am looking for. i remember it working in the trial version late 2013 photoshop. it was so simple i thought it would be hard to forget how, but i must be missing something. i looked, clicked and checked all around the work space to find a way to change from "background layer" and did not find it. the trial version (lets call it "trial period" because its all the same except paid for now along with updated to ps 2014) did also have the layer change in an easy to find way. i believe it was double click or right click over the currently active layer in the list as in the lower snip pic.
the pic above did work during my trial period so i know it works somehow. i dont know what i am missing now. right click or double click now does not bring up the layer type selection in the menu like you suggested to change from backgroung layer. also every new picture file i open makes its own new layer. when i make a new layer i havent figured out how to put a pic in it. if you could show me how to create this effect or find my missing step that would be awsome.

Has anyone enabled time machine using a linksys router and external hard drive? And if so how?

Has anyone enabled time machine using a link sys router and external hard drive? And if so how? I have a Linksys E4200 wireless router with a usb port on it. I also have a Western Digital Elements 1TB external hard drive. I would like to be able to use this hard drive with time machine. Has anyone done so and if so how can I do so?

You might get some responses, but we don't see many Linksys users on an Apple forum so it may be awhile before you see an answer.
It might be useful to point out that Apple does not even support Time Machine backups to the USB port on their own AirPort Extreme wireless router, so we may be heading down a very slippery slope here.
I've tried Time Machine backups on an AirPort Extreme router a number of times in the past. It's just not reliable. Works for awhile, then has corruption problems. Or has corruption issues immediately. I once went a month or so and thought I had it nailed, then got smacked with a corrupted set of backups again.
But, I guess you never know. It might work on the Linksys. If you decide to try this, I would suggest that you have another backup plan in place for your important data.
Hope that some Linksys users will respond so we can all learn.

External hard drive not recognized after time machine locked up

I was backing up to an external hard drive (300GB Western Digital) and time machine locked up. I had to shut down the computer and restart. Now the external hard drive does not show up on the desktop?
I can see it in disk utility but I am not able to mount or unmount the disk, I keep getting an error that the disk is in use. I tried to erase/reformat the disk and no luck.
Any suggestions?
Thanks for the help

KTM450rider wrote:
Do I need to boot from the install DVD?
this is often the easiest and eliminates any "busy drive" problems. what's wrong with booting from the install DVD? takes a couple of minutes.
My main hard drive is OK... the drive that I am having problems with is an external hard drive that I was using to back up my lap top. I just want to get the external drive reformatted, but disk utility will not erase it. I get an error that disk utility shut down, "please check the drive and make sure that the drive is not in use or programs are still running"
Is their a way to do a hard or forced reformatting of an external hard drive, I don't care about the information on the drive
I also tried disk warrior to recover the info on the disk and all it does is crash my mac pro????
Thanks again for the help

Can I delete my music on my Macbook air now that I have time machine set up?

I cannot see the music files on the time machine. Can I delete my music on my Macbook air now that I have time machine set up to an external hard drive?

The Time Capsule is for your Time Machine backups, not "everyday" files. .
If you delete the music files on your MacBook Air.....there are a number of negative things that can occur.
1) The only copy of your music will be on the Time Capsule. When....not if....the Time Capsule has a problem, you will lose your music files, since you have no backup for them. In other words, you always need at least two copies of your important files on two separate drives.
2) Time Machine backs up the changes that occur on your MacBook Air. If you delete the music files from the MacBook Air, at some point Time Machine will also delete them from the Time Capsule.....and there is no way to know when this might occur.
A better plan to consider might be to add a USB or FireWire drive and connect it directly to your MacBook Air. Move the music files over to that drive.
Then, Time Machine will back up both your MacBook Air and the attached hard drive. So, you have an "original" copy of your data on one drive and a backup copy of the same data on the Time Capsule. That would be a minimum backup plan.

Time Machine from 2 computers to one HD - why are the backups different?

I have an external HD linked by fire-wire from one PowerMac. I have an iMac linked by ethernet to the PowerMac. I make the links, so the iMac and its Time Machine can 'see' the external HD.
Both machines run Time Machine, backing up onto the external HD.
HOWEVER:
the PowerMac creates a backup folder, then puts the backup into that folder, as another folder. I can see the contents.
the iMac creates a "sparse Image disk bundle," a single file, that I can't see inside of.
Have I set up Time Machine wrong? Am I really backing things up to the external HD?
Additional info:
The "old" MacBook (10.4.11) puts a Silverkeeper backup file on the external HD also.
There is plenty of available space on the external HD.
Whatever Time Machine does to announce completion of a back up, I don't know what it is. There ought to be 2 modes of operation for it - (1) for beginners, to hear & see when things happen, and (2) for comfortable users who trust this near miracle software to do its job. [How does one become comfortable with something that never explains what it does/did? Appears like a Window 95 network printer.]

Jay Warner wrote:
The "old" MacBook (10.4.11) puts a Silverkeeper backup file on the external HD also.
Are those backups in a separate partition? If not, that's eventually going to be a problem. It would be best in this case for your TM drive to have at least 3 partitions (see #3 and 4 in the Frequently Asked Questions *User Tip* at the top of this forum):
The PowerMac's TM backups.
The iMac's backups.
The Silverkeeper backups.
Whatever Time Machine does to announce completion of a back up, I don't know what it is.
As Mr. Boyd says, you can see this from the TM icon in your menubar, and also in the TM Preferences pane. Both will also contain an indication of a problem (although the one in the menubar is a bit hard to see).
You might want to review these:
Time Machine Tutorial
Time Machine 101
How to back up and restore your files
Time Machine Features
Apple - Support - Mac OSX v10.5 Leopard Time Machine
and perhaps browse the rest of the FAQ Tip.

HT201250 Anyone have time machine "lock up" while backing up and not completing the task?

Similar Messages

Maybe you are looking for