HT201263 my ipad will not recover it shows constnt low battery

my ipad will not resore and shows a conatant low battery
it was fine until ios7.0.2

Did you try to recharge your iPad's battery?

Similar Messages

  • Ipod will not charge, keeps resetting, extremely low battery.

    Someone please help!!
    I adore my Ipod, its 2+, it was working fine, till a few months ago.
    In the beginning, it stopped charging on the computer, it synced, but i would have to charge in on a Ipod radio thing first.
    Then after awhile, on the radio, (it worked perfectly at first) the ipod would come up with the message, "This accessory not supported by Ipod", it would still play on it, movies, songs, and charge it, but the message would come up every often.
    Now it refused to be recognized by the radio, and won't charge.
    (yet if you press play the song and movies will play)
    It had very little battery left so i bought a wall charger.
    I tried charging with a wall charger and car charger!
    Now its basically dead, and when i plug it on to the wall charger, the apple logo comes on, and it goes to low battery message, then apple logo..again again.
    It just keeps resetting, so i took it off that.
    Leaving on the charger for awhile won't work, because it just keeps doing that.
    What do i do?
    I can't restore it, because i'd have to charge it first!
    (I got a new battery for it a few weeks ago, the battery life was way better, charged a bit faster, and it seemed to work better, but the computer still drained it)
    Anybody have any ideas?
    Please please please.
    I swear i love it, but i'm going to throw it out the window soon.
    -edit,
    just to add, the first thing that went wrong, that started this thing, was when i got that -48 error, it doesn't do that anymore just to add
    Message was edited by: Imjustkeeding

    I have the same problem and sent my ipod to a the service center for a battery replacement. I was informed by them first by email that "Our technicians have performed full diagnostic checks on your IPOD 5TH GENERATION and have been unable to reproduce the symptom(s) you reported when you requested the repair. As a result of our tests, we can confirm that your product meets Apple specifications for performance, usability, and functionality." then I was told over the phone that they reloaded the software and firmware and that it is working properly and is being sent back to me. Then, and heres the kicker, I received my i pod back with a form stating it was a hardware failure affecting another component. I have since called multiple times and no one can tell me where the hardware failure is but the ipod still says its a battery issue. Go figure i think apple knows exactly what the faulty part is that is causing this error and has no solution short of replacing the unit and they dont want to replace the units of all those with this hardware failure

  • IPhone 5 will not turn on. Endless Low battery, Apple Logo, reset loop

    Today I dropped my phone, not a big drop, only about 2 feet. I had a lifeproof case on so I thought to myself," No big deal" To my shock and disbelief, my phone would not turn on! I tried to plug it in to a charger to try to start it. It immediately came on with a low battery symbol. I thought that was strange as it had a 70-80% charge on it. But I was hopeful. It then displayed the Apple Logo and I thought I was safe. Then after about 5 sec it went blank. Then the Low Battery symbol came on again. Then the Apple Logo for a few seconds, ... then Off. It does this over and over in an endless loop. I dont know where to go from here. I tried googling the problem but didn't come up with much. I tried holding the home and power button for 20-30 seconds like one video recommends but that did nothing. It only loops if its plugged in to a charger. If its not plugged in it is just off, no activity at all and it will not turn on. Any help will be much appreciated.

    Just to follow up if anybody else has this problem.
    The drop must have ruined the battery. After taking it to a local repair shop to get serviced, as suggested by Ingo2711, the phone is back to 100% after a new battery was installed. $50.00 bill for a new battery is not to bad at all to fix my phone.

  • HT201263 My ipad will not show the recovery mode, it goes into DFU mode just fine, but whenever I put it in recovery mode I get nothing but a blank white screen. After doing a restore or update itunes gives me error 37. This all happened due to a failed u

    I updated from ios 5.0.1 to 5.1. Midway through the update itunes crashed. I got it all working again and ever since I have been stuck in a recovery loop. DFU mode works fine, but when I go into recovery mode (yes I am doing it right, yes I have tried pwning, tinyumbrella, etc.) it still just gives me a white screen (I am not getting the plug arrow and itunes icon screen that shows up when you are in recovery mode). I am a huge fan of hacking, mods, and jbs, BUT have never done any on the iPad, (found it pointless).. nevertheless, I am stuck thanks to apple in a white screen and a nonworking iPad. If anyone has any ideas that does not include jbs, updating, restoring, restoring with internet off, restoring in DFU, I would gladly appreciate it. I would take it to the apple store but it was a friends and I didn't purchase it. My friend had the issue formerly and they had no idea what to do at apple (they usually try DFU, restore, and then have nothing else to tell you.

    There's a whole lot to read in your post, and frankly I have not read it all.
    Having said that, this troubleshooting guide should help:
    http://support.apple.com/kb/TS1538
    In particular, pay attention to the mobile device support sections near the bottom, assuming you have already done the items above it.

  • HT201263 my ipad will not turn on no matter what I do... there is a weird cloud shading around 3 of its corners... is it dead?

    I have tried all of the factory reset items such as pressing home key with sleep key as well as hoelding home key while trying to plug into my PC. Nothing happens. the screen is blank. Also, in 3 of the 4 corners of the ipad, there is what cloudy matrial that I have not seen before.
    Is there any hope of making it come back on???  HELP!

    beckyvicki wrote:
    .... Also, in 3 of the 4 corners of the ipad, there is what cloudy matrial that I have not seen before.
    Doesn't sound good...
    The Basic Troubleshooting Steps are:
    Restart... Reset... Restore from Backup...  Restore as New...
    If you try all these steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
    Be sure to make an appointment first...

  • My iPad will not show up in iTunes but my iPod does

    Hi there, my iPad will not show up under Devices on iTunes but my iPod is showing up ok.  Any help please??

    I have the latest version of iTunes - my iPod is working perfectly ok, its just my iPad will not show up in iTunes.

  • HT201412 ipad will not do anything but show apple icon ?

    ipad will not do anything but show apple icon help please ?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • Tried to open an app and my iPad gen one froze. It only shows the apple on black screen and will show the operating wheel sometimes and while plugged in it will beep every few minutes. Will not load one show anything on screen but the small white apple.

    Tried to open an app and my iPad gen one froze. It only shows the apple on black screen and will show the operating wheel sometimes and while plugged in it will beep every few minutes. Will not load one show anything on screen but the small white apple.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • My ipad will not charge up. it just shows the red battery signal and then switches off

    my ipad will not charge up. it just shows the red battery signal and then switches off. The same charger succesfully charges other idas so i know it is no the charger that is faulty.Any suggestions

    Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    iPhone: Hardware troubleshooting (Power/Battery section also applies to iPad)
    http://support.apple.com/kb/TS2802
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    iPad: Charging the battery
    http://support.apple.com/kb/HT4060
    Best Practices for iPad Battery Charging
    http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    How to Save and Prolong the battery life of your new ipad
    https://discussions.apple.com/thread/4480944?tstart=0
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    To Extend a Device’s Battery Life, Get to Know It Better
    http://tinyurl.com/b67c7xz
    iPad Battery Replacement
    http://www.apple.com/batteries/replacements.html
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom
    BTW- Your profile shows you have iOS 6.1.4 installed. The max iOS for an iPad is 6.1.3. iOS 6.1.4 is for iPhones only.

  • IPad will not connect to wifi, shows connection, iPad will not connect to wifi, shows connection

    My iPad will not connect to wifi, even though my computer is currently connected.  Airport mode is off, and my iPad shows connectivity in the corner.  Is there any way to fix this without completely resetting the device?

    - Reset the iPad. Nothing will be lost
    Reset iPad: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router.
    - Reset networks settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points
    Does the iPad successfully connect to other networks?
    Did it successfully connect to this network before?

  • My new ipad will not sync with itunes.  the device does not show up in itunes

    my new ipad will not sync with itunes.  the device does not show up in itunes.  I am on a Windows system

    Do you have the absolute latest version of iTunes downloaded?  If your iTunes software has not been updated in some time, your iPad will not be recognized.  With iTunes open, click on Store at the top.  Check for available downloads and if there are any, download them.  Once you've verified you have the latest software, connect your device again, and it should be recognized.

  • HT4356 my iPad will not print to my AirPrint printer. The print center shows the printer but it continually says "waiting"

    My iPad will not print to my HP AirPrint printer. The print center shows the printer and the print job but the print center continually shows it is "waiting"

    This article states that if your printer is not listed you can't airprint from your idevice but I have printed from my Ipad to my HP Officejet Pro 8600 in the past but now, all of sudden, I no longer can't. I'm trying to print from the "note" app but every time I try to print it keeps sending to my printer but never prints. Constantly buffering and sending, that's all it does. My color ink levels are all low but I have plenty of black ink left. EXTREMELY FRUSTRATED WITH APPLE AND HP!!!!

  • TS3274 My iPad will not show up in My Computer

    After updating iTunes last night only to find that Apple Support services would not start, and doing a clean reinstall of iTunes and all its componants, I now have another problem...
    My iPad will not register on my computer, or iTunes.
    It wants to connect and my computer even gives the connection sound, telling me that a new device as been connected, but then the iPad asks if I trust this computer. (as if I haven't had the iPad connected to this computer for the last three years!) When I press the TRUST button it DISCONNECTS and my computer gives me the disconnection sound!
    I checked the device drivers and there is a Apple device USB driver but it doesn't give anymore information other than the notice telling me that "This device is working normally" Hows that for irony?
    Please Help!
    MSRankin

    iPad not appearing in iTunes
    http://www.apple.com/support/ipad/assistant/itunes/
    iOS: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/TS1591
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    iTunes for Windows: iTunes can't contact the iPhone, iPad, or iPod software update server
    http://support.apple.com/kb/ts1814
    iTunes for Windows: Device Sync Tests
    http://support.apple.com/kb/HT4235
    IOS: Syncing with iTunes
    http://support.apple.com/kb/HT1386
    Apple - Support - iPad - Syncing
    http://www.apple.com/support/ipad/syncing/
    iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi Syncing
    http://support.apple.com/kb/ts4062
    iOS: "Not enough free space" alert when trying to sync
    http://support.apple.com/kb/ts1503
     Cheers, Tom

  • HT201263 None of these answers help my problem.  My ipad will not leave the Apple logo.  I hold both buttons and the screen goes black, then the apple logo immediately pops back up.  I can't do anything because the apple logo just keeps popping back on.

    I haven't been able to find any answers that solve my problem.  My Ipad will not leave the Apple logo.  I hold both buttons and the screen goes black and then the Apple logo immediately pops back up.  I can't get the red slider screen at all.  No matter how many times I hold down both buttons the screen goes black and then the Apple logo pops right back on.

    Before you do anything else, try charging via a wall outlet for a while, since its off. Then try turning it back on.
    When you put the device into recovery mode it allows you to restore the device when no other options work. You do risk losing everything currently strored on the ipad itself. Hopefully you've performed regular backups either via itunes, icloud or both. Evern if you have synced content to either of those, you may not lose everything. All previous purchases have been saved in the itunes and app stores, so you can dowload them again.
    while the ipad is off, press and hold the home button and plug the usb cord into the ipad. You should see a message pop up on the itunes window on your compoter screen that state it has discoverd an ipad in recovery mode.
    You should now be able to restore

  • HT201263 Help.  My wife's iPad will not start up.  I updated it two nights ago (Nov 12) to the latest  IOS.  It seemed to update normally. However, today it will not start or give any response.  I tried to do a restore, but it will not let me do that.

    Help!!!!!!  My wife's iPad will not start up.  I updated two nights ago to the latest IOS and today it will not do anything.  It is charged and I've tried to access it through itunes to no avail.

    From your text, it's difficult to determine if the problem lies with the iPad or the cable.
    If the iPad still works, but you're having a problem with the sync, you may want to check all the cables and connections. If the iPad doesn't work (frozen or unresponsive), post and we'll go through the checklist together.

Maybe you are looking for

  • Vendor balance

    Hi Friends, my client wants to know, what is the other side of the entry made to vendors balance. I couldnt find any field in vendor reports which tells me what is other side of the entry, if I pull GL account number it gives me the recon. account fo

  • Report Generation Toolkit - Error message rpcrt4.dll

    Hello My labview app. calls functions from the Report Generation Toolkit. I tested the runtime version, and this work fine under in Windows NT and Windows 2000, but does not work under Windows 98. I got and error message say "rpcrt4.dll Page not vali

  • XDB.PATH_VIEW compilation error

    Dear Expert, I having a problem on create acl. Error *[ORA-04063: package body "SYS.DBMS_NETWORK_ACL_ADMIN" has errors]* occurred during create_acl. I tried to compiling"DBMS_NETWORK_ACL_ADMIN" package manually on sys account. Another error *[ORA-040

  • Problem while customising Dispatcher message

    Hi everyone,    I want to change the message "<b>dispatcher running , server not connected</b>" This is what I have done . 1 created a /msg directory  under cluster/dispatcher. 2 in there, created a html file called dispatcher.html 3 use the J2EE con

  • CO Production Order

    Hi, I created one Co Production Order (KKF1) and I want to do a lot of goods receipt using this same order through MB31, Type Movement 101. But after I make one goods receipt I can't do another one using the same order. This error appears: "Document