HT201328 Error after unlocking - need to reset data settings Access Point Name

Hi -
AT&T unlocked my phone few months back. I restored the phone and got "iphone unlocked message". After inserting the new SIM card, I cannot get on the cellular network. I think I need to reset the data settings access point name. However I am unable to access this option. Can someone help?
Thanks

I had the same problem and I fixed it as following (See if it's the same case for you) :
1. Goto Tools > Options.
2. Under Advanced, select the Network Tab.
3. Click on Settings in the "Connection" box (open connection settings).
4. Check if "Automatic Proxy Configuration URL" is selected. If it is so, select "No proxy" instead or manually enter your proxy if you are using one.
The option "Automatic Proxy Configuration URL" was the culprit for me and some others as well and selecting "No proxy" instead cured our problems. It is a bug and has already been reported on Bugzilla as you can see here :
https://bugzilla.mozilla.org/show_bug.cgi?id=734828

Similar Messages

Gen. 2 iPod Touch is stuck on Apple Boot Logo after Resetting Data/Settings

My iPod Touch hadn't been getting recognized by iTunes and my music wouldn't sync onto it so I went into the Settings app and clicked Reset Data & Settings (the 4 hour long reset) and waited while the bar slowly moved until it finally restarted and showed the Apple Boot Logo. I then waited for about 20-30 minutes for my iPod to turn on and it never did, so I reset it by holding the Power+Home button and that didn't do anything as it was still stuck on the Apple Boot Logo. Then I remembered I could have just put my iPod into DFU or Recovery mode to get iTunes to recognize it to reset it, so i tried to put my iPod into both modes and it wouldn't go into them. So I went to bed and just woke up and it's still stuck. I'm afraid I might have bricked my iPod, and I'm out of my warranty I believe. Does anyone know ANYTHING I could try? I don't care about data loss seeing as I already tried resetting the whole thing.

If it is still doing it after a restore, you most likely have a hardware issue.
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

HT1725 42404 error after downloading itunes (20+ times!) can access the itunes store but can't do any downloads... itunes support has not offered any valid suggestions

42404 error after downloading itunes (20+ times!) can access the itunes store but can't do any downloads... itunes support has not offered any valid suggestions

This is EXACTLY what happened to me and many others. Tech support returned most of my money but not all of it. Figure that one out! It is clear no music is downloaded (or in queue), it is clear an unknown error message is produced, and it is clear we, the consumer, are still being charged anyway. Will Apple require a credit card from its customers and alienate those that do not wish to use a credit card? Will Apple insult its customers and make silly suggestions such as 'Use an iTunes gift card' in much the same way a forum moderator has already recommended?
I have an idea: Acknowledge the problem publicly (via email, for example) and fix it in a future update. Customers will be more understanding if they know there is a temporary problem and Apple is working hard to fix it. Oh, and return our money, please!
Windows XP Pro
Windows XP Pro

CP1525 need cold reset process, cannot access menus

CP1525 need cold reset process, cannot access menus. I guess this has to be sent by private message, so I will try to figure that out next.
I have someone that thinks it is funny to enable only IPv6, set a password and lock everyone out.
Guess I need to set it up properly and lock the printer down.
I guessed at my d401 reset (If you could send the real proceedure, just in case) I would appreciate that also. I am not sure it is actually properly done. In addition to the CP1525n.
Thank You

Hi @johnwise ,
I see by your post that you need the reset for the printer. I would be happy to help you.
I can send you that information in a private message.
In the forum beside your handle name just click on the envelope to view it.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

An Error Occurred while trying to join "my wireless access point"

Hi,
I've been using wireless access for a year and never had a problem connecting.
But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
I get the strange feeling that they planted some kind of bug/virus!!!
I don’t know what else to do.
Anyone knows that problem? What can I do?
Any help is greatly appreciated!
I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

Hello Tesserax,
I get the same error message again...
I tried the 3 suggested steps again, but unfortunately it did not work.
After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
Even if the Computer was asleep for just a second!
I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
And it works fine…until the screensaver comes on or it sleeps again
I have the Problem with my IMac and Mini but the IMac at least remembers my password…
Any Ideas
I’m connected through a Buffalo WZR2-G300N wireless router

Packet Data Access Point Names vs real data server...

I am trying to activate an application that requires GPRS.
I currently can get EGPRS and assume that will do the same but faster. But I have a question that may not pertain to this but as I am new at this I will ask it here. From reading I see that the settings of packet data appear to have more to do with setting up phone as a modem to use. So I don't know truly if this has any bearing on my problem with the software registering to complete the setup of it.
However my web access which is unlimited month to month internet access which allows me to go anywhere on web (not a walled garden) also uses this GPRS or EDGE version of GPRS. I am in the USA with T-Mobile. Phone is set to use GSM. The screen where it concerns connectivity says that I have Access Points which were configured by T-Mobile sms file they sent me twice. I actually have 5 names under Access Points.
1)MMS = wap.voicestream.com
2)T-Mo WEB = Internet.voicestream2.com with small i in settings
3)T-Mo WEB(01) - this from 2nd sms copy same
4)T-Mobile Internet = Internet.voicestream2.com with small i in settings too.
5)t-zones this is their wall garden = wap.voicestream.com
ok since I can browse the web anywhere and download the application I don't know why I cannot register it. But it states it needs an internet connection before activation through authentication, or basically registering it to use.
So I am trying to do this after verifying that I have an internet connection with the too connection arrows symbols on phone screen showing internet connectivity with E over them currently by starting a browser first as the application doesn't seem to do this for me when trying to activate it.
E
--> where the lines are solid. Ok here is my issue here.
The arrows are not coming up correctly in this forum anyway I get what shows I have EGPRS connectivity, I don't know if the application is sensitive to using GPRS only but will find out. I doubt it. The GPRS would show the arrows with an antennae above. I am talking about the indicators from what the pdf and book say.
Below Access Points on the menu in settings for connection is Packet data.
Packet data has to variables
1) when needed , or when available
2) Access point
Access point is blank. Should I enter one of T-Mobiles names in the list above this under Access Points such as
T-Mobile Internet or should I put the server name in specifically internet2.voicestream.com?
I set the Data Call setting to Unlimited to make sure if its using this process it doesn't turn off after the 5 minute default on the next setting.
Any ideas why this gprs app is not activating itself and making the gprs internet connection with the pin I was provided? I had to use the pin just to download it and install it.

that will work. You only need to change if you need to have always on (highly unlikley) or if you are using modem dial up and need to specify access point for that.
If you using Nokia One Touch access then you don't even need to define access point in this menu as that application will take care of it for you.
All other network aware applications will use access point settings as defined in settings menu.

A tech company just set up a wifi network in my house and does not use my existing TC; how do I get it in the network to serve as backup for my iMac? (I don't need it as a wifi access point anymore)

a tech company just set up a wifi network in my house and does not use my existing TC; how do I get it in the network to serve as backup for my iMac? (I don't need it as a wifi access point anymore) thanks

Just bridge the TC and plug it by ethernet into the main router.
Bridge in v5 airport utility.
In v6 it is under network.. change it from DHCP and NAT to Off bridge mode.
Turn off the wireless.

Need to reset Data Warehouse

Hi,
I need to reset the Data Warehouse so that i can begin my first ETL Process. However, I'm not able to do so from DAC Client ver 7.9.5. When i click on "Tools" --> "ETL Management" --> "Reset Data Warehouse" nothing pop up's. Not sure why, all other links and windows opens, except for this. How can i get this fixed ?
Is there a way for me to do the reset manually ?
I checked on internet and found AS BELOW :-
D4 How do you run a full load (not incremental)
A: Reset data warehouse . Just truncate the S_ETL_REFRESH_DT table in the dac repository
So in our case the table to truncate will be W_ETL_REFRESH_DT rite ? Please confirm. We are scheduled to run the ETL at 6pm today.
Is there any other tables that i need to truncate as well ?
Thanks,
Saran.

Hi
W_ETL_REFRESH_DT is a metadata table on which you should never perform truncate operation.
Also,Whate 'Reset Datawareshouse' does is it just updates last_refresh_dt of w_etl_refresh_dt to NULL.
So,all you need to do is
update w_etl_refresh_dt set last_refresh_dt=NULL;
commit;
Hope this helps.......
regards

HT201328 Problems after unlocking my iPhone with ATT

After unlocking my iPhone 3GS with ATT and going through the restore process via SIM card, WiFi and iTunes, I am unable to re-activate my phone.
Using a T Mobile SIM card and/or via WiFi I get a message that the server is temporarily unavailable. When I try iTunes, I get a message indicating that there is no SIM card inserted when it has one in.
Help?

Never got the "Congratulations" message. The phone stops when looking for telephone connectivity (third step after choosing a WiFi network).
The phone whas unlocked and jailbroken long time ago using a thrid party software but lately could never update it to a more recent iOS. Apps were not being updated and stopped working. So, I decided to unlock the iPhone using the ATT/Apple process. I updated the iOS before unlocking it using the Apple/ATT instructions.

Error when executing Query with user date settings = mm/dd/yyyy

Hi all,
I created a remote cube with datasource = TCURR table with proper conversion of the date etc.
The query on top of this remote cube works fine if my user date settings is set to dd.mm.yyyy
But when a user in USA, with user date settings = mm/dd/yyyy, executes the same query, they get a message
SYST: Date 31/05/2006 not expected.
Message no. FGV004
The input variable on the Query is on 0CALMONTH.
This message appears immaterial of what calmonth input I give.
has anyone encountered this error? if yes, what could be the solution please?
thanks
Emmanuel

Hi,
This is in regard to the user settings maintained in transaction /nsu3.Please follow the below link.
http://web.mit.edu/sapr3/docs/webdocs/getstarted/gsSETTINGS.html
You need to change the settings as required.
Hope this helps.
Thank you,
Prem

Wi-fi network joining trouble and need to reset network settings

iPhone 4 when turning on phone will not join network until I reset network settings. Sometimes need to do this twice befor it joins my home network. Anyone else experiencing this? Solution?

Did you already go through this article about troubleshooting Wi-Fi? http://support.apple.com/kb/TS1398

Reset Cisco 1140 Access Point

Hi,
I need help resetting the Cisco Aironet 1140 model AIR-LAP1142N-A-K9. I need to access its web browser but I don't know the password. I perform the mode reset method, but that didn't do anything. Maybe I have to access its CLI, but that I don't know how. Any help would be gladly appreciate.
Thanks.

I type "show interface bvi1" to obtain the ip address, but it seems that it wasn't able to find it:
ap>show interface bvi1
BVI1 is down, line protocol is down
Hardware is BVI, address is d48c.b5b0.0b56 (bia d48c.b5b0.0b56)
Internet address will be negotiated using DHCP
MTU 1500 bytes, BW 54000 Kbit/sec, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:40:21, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2 packets input, 658 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
3 packets output, 718 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out

E5 Packet data connection/access point

I was just wondering what this is.
I think I don't need it being as I don't have a "Data Package" set up with AT&T...am I right?
If I'm wrong, what to do next.

This would be needed for internet access and mms usage on your phone. Internett access only if you're thinking about surfing on the network. Wlan does not require any data packet connection over the phone network but will be saved as an access point though.
You will also need a packet data connection for using A-gps as it needs a few kb to locate the phone through the network.
But you can use the gps without agps.
So if you don't plan on browsing internett on the phone network, you don't need a packet data connection for that/ acces point.
If you don't need to send mms, you don't need one for that either, but those acces points are separeted from each others.
If you can not send mms, but you want to, you will probably be able to order the settings (accesspoint) from your providers web page. It will usually be in form of a text message sent to your phone. Same for the other access points.
Did this help you in any way or was it just confusing?
A Packet data connection will pretty much be an access point for internet/mms/wap over your network.
Using you wlan will be installed as a access point too, but that will of course be free (or just cost what you pay to have your internett).

Need to reset prefences settings after recharging the battery

Hello,
For some reason, everytime I recharge the battery after it is completely drained, I have to reset the language, date, time, etc on my Ipod.
It dosent ever happen when I charge the battery after being only partially drained, only when it's is totally drained and recharged...
Anyone have any ideas?
Thanks!
jcop

Hi groundflight5150,
I'm attaching a link below to the user manual for the 8150B series of controllers. I don't believe that the BIOS is password protected by default, so you may want to contact the person you purchased this from to find out what the password is. However, there is information in the manual regarding how to clear out the CMOS contents, so this might help.
PXI-8150B Series User Manual
http://www.ni.com/pdf/manuals/322321a.pdf
Josh B
Applications Engineer
National Instruments

Error "After Effects Needs Two or more Frames to Playback" in AE 13.2.0.49

Can someone please help me I'm having this problem also.
I'm using 13.2.0.49 and have updated today. I have emptied the Disk Cache and Cleaned the Database and Cache from the AE preferences, I have quit and opened the project several times. I have the Reduce cache size when system is low on memory box UNTICKED.
So what do I try next can someone please help Adobe??

Some more info would certainly help. Tell us as much as you can: FAQ: What information should I provide?

HT201328 Error after unlocking - need to reset data settings Access Point Name

Similar Messages

Maybe you are looking for