HT201401 I Phone shuts itself off after a few minutes when docked to a compatable radio

I Phone shuts off after some time when docked to a compatable radio or stereo. Sometimes after 20 minutes, other times after only 2 - 5 minutes

Hi,
You can refer to this blog, and try to roll back to the older version of network adapter driver to check the results.
Windows 8.1 Wifi showing "limited" or "No Internet Access"
http://blogs.technet.com/b/dennis_schnell/archive/2013/08/31/windows-8-1-wifi-showing-quot-limitied-quot-or-quot-no-internet-access-quot.aspx
Meanwhile, please check with the manufacturer of your router to update the firmware.
If the issue persists, please help to collect following information for further research:
Over an Administrative command prompt.
C:\> netsh ras set tracing * enabled
Over an Administrative command prompt.
C:\> netsh trace start scenario=netconnection capture=yes tracefile=c:\net.etl
Over an Administrative command prompt.
C:\> netsh ras set tracing * disabled
Over an Administrative command prompt.
C:\> netsh trace stop
From the Client:
b) C:\Net.etl and C:\Net.cab
Upload these files in SkyDrive and post back the shared link.
Keep post.
Kate Li
TechNet Community Support

Similar Messages

When on battery power, my IPod Nano it shuts itself off after 2-3 minutes. Any ideas what is wrong and how to fix it?

Can anyone help me keep my iPod Nano from shutting itself down after 2-3 minutes on battery power? It works fine when connected to a power source.
Thanks,
George

Try here to fix it. I doubt that you will ever find out why it did that.
iPod touch: Hardware troubleshooting

My Pavilion G4 shuts down after a few minutes when I plug it in

My hp pavilion G4 shuts down automatically after a few minutes when I plug it in. It does not happen regularly so I'm not sure of the reason of why it happens. The laptop shuts down and when I press the power button, the light on the power button just flashes but it does not start. Even if I remove the charger and push the power button, it doesn't start. I have to remove the battery and place it again to be able make the laptop start again.

Hi rierufied,
Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that you are having a problem with your g4 shutting down randomly after you turn it on. When this happens do you get an error message at all? If so, what is the error message? Does this happen both when you are on battery and when it is plugged in? What operating system are you using? What is the product number of your notebook?
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Update: Video - Canon 6D turns itself off after a few shots with fully charged battery

Update: I uploaded my video to youtube, please comment:
http://youtu.be/3PNLUYd8g7A
TIA and pardon me for my English.
I posted this originally at another forum, and somebody suggested me to post it here as well, to get more help.
Long story short, I purchased a brand new Canon 6D from B&H on Oct 24th, 2013. From early december, the camera starts to shut itself off randomly and displaying empty battery. I found the camera constantly shuts itself off after 20 - 100 continuous shots with a FULLY charged battery (right off charger, showing 8.23V using multimeter, and showing 98% in battery info).
The camera will just turn itself off in the middle of shooting, showing empty battery int the shoulder window. The solution is simple, open the battery door, then close it again, no need even to pull the battery.
So, I contacted Canon support, sent the camera to the VA service facility, waiting for it be repaired. As an engineer myself, I understand things fail, and I thought this is such an easy issue to reproduce, anybody should be able to repro it.
Couple of days later, I received a phone call to send my accessories in, no problem, debugging needs more info, that's normal. I sent my lens and stuff in. I unfortunately had to bear the cruel fact that I don't have a decent camera for the holiday, though I have a backup.
After a long wait, on 12/28the, the accessories were delivered at 9:35am. At 10am, they called me, they were sending the camera back. No issue at all. I was like, have you tested AT ALL? They didn't care, sending the camera back regardless.
I received the camera on Jan 2nd, and saw the same issue on that day. Of course, it was NOT fixed at all.
I googled really hard, somebody said he had similar issue but it was a defective battery, so I got a brand new Canon battery, unfortunately, the same issue pops up again.
Ok, the only choice for me is to send it back again. But this time I am totally amazed by Canon.
I sent the camera in again with my lens and battery. Also, a video showing the issue on a standalone CF card (I know 6D does not take CF, just to put the video on it).
Couples of days later, they called asking for accessories, I was like, what accessories, I don't have any more.
Then the camera sit in their facility for a few days for nothing. All of sudden I received a phone call on Monday morning, said it is ready. The camera has no issue at all.
I called, asked whether they have watched the video, they told me two technicians, including a senior one, was not able to upload the video to the computer. I was like, what the hell? why the heck you need to upload it to the computer, find a card reader, plug the card in, double click, how simple is that?
I talked to the service manager over the phone, he told me that there is nothing he could do, if their technician said so. They have decided to send my camera back, NOT fixed, again. I esclated the issue again, but haven't heard anything back yet.
Honestly, I am totally pissed, how stupid can they be? I included a letter with detailed steps on how to reproduce this issue. As an engineer myself, I know how easy to reproduce this issue. But what shocked me is that they don't even know or they didn't even bother to watch the video. In the same letter, I asked/begged them to contact me if they cannot reproduce the issue instead of just sending it back unfixed.
Guys, any other ways to get their attention? I already filed a BBB complaint. For a brand new camera of 3 months old, it has been in Canon's repair shop for almost a month. Leave to say that I missed the most importand holiday season in the year. This is simply not acceptable.

"The camera usually shuts itself off after 20-100 continuous shot, ..."
By this you mean your are in continuous drive? You just hold the shutter release down until it stops shooting?
"... the shoulder LCD shows a ..."
What is the "shoulder" LCD?
Sorry for the extra questions but I am trying to understand exactly what you are going through and why Canon said it is OK.
Canon did not say it was all right if it is not.
You are, also saying, if you use the camera, just for a single snap shot, say several in a session, it is OK? Right?
It only shuts down when on continuous drive or video?
EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
Photoshop CS6, ACR 8.7, Lightroom 5.7

IPad Personal Hotspot antenna shuts off after a few minutes of non-use. This happens in both Verizon 3G and LTE areas. Turning off LTE does not help. Turning Personal Hotspot off and then on works. Does this happen on Mini and Retina?

iPad--third generation shuts off antenna/hotspot after a few minutes of non-use.
Happens in 3G and LTE VZ environment.
Turning hotspot off and on getsw things working again.
Does Apple have antenna on a timer so it shuts off after a few minutes?
Does this happen on Mini and Retina as well?
FLAGSTAFFLAR

Fixed!
Two things together have restored connectivity.
1. I changed the name under Settings > General > About > Name from My Name's iPad to iPad of My Name. I read somewhere that iOS 7.0.1 or 7.0.2 (I forget which) sometimes had issues with apostrophes here. Easy enough to test.
2. I then reset (again) the APN settings under Settings > Cellular Data > APN Settings > Personal Hotspot and reentered our provider's info (APN, Username, Password) there.
I don't know WHY it worked, but the personal hotspot is now happily sharing (again) internet connectivity with my MacBook Pro.

Facebook shuts down unexpectedly after a few minutes.

When using Facebook on Safari, Google Chrome or the app it shuts down unexpectedly after a few minutes. I tried restarting my iPad, reloading the app & deleting the cookies. It's frustrating.

Gilroy4 wrote:
Just this evening, my new 23" Intel i3 Mac starts randomly shutting down after a few minutes each time. Thoughts?
Humm.... my first thought is that the new iMac's only come in 21.5 and 27" and the second is that your not giving us much to go on. You know things like, it ran fine for the first hour, day, week, month, I checked the power cord to make sure that the connections are tight, I followed the User's Guide, it was working fine until I upgraded the RAM, plugged in my printer, an External Hard Drive, I started having this problem after I downloaded xxxx, it fell off the desk, I dropped it down the stairs on the way from the car to the house, the UPS driver kicked it off the back of the truck, you know the basic stuff like that.

Screen turns off after a few minutes and needs to be closed then opened

hi, as the title suggests my powerbook screen turns off after a few minutes before my screensaver is set to come on and when i come back and press a key or move the pad it wont start up so i need to close the powerbook then open it up again for it to activate. its not a huge problem but my programs which connect to the internet seem to lose their connection when i open it up again. is this normal? is there a setting i can change?
thanks
ross

Is there a way to "disable" Standby, Suspend and Off just when watching movies (in fullscreen or not)? I want them to do what they usually do in all other cases.
Setting them to 0 in xorg.conf does the thing, but I need that functionality only when I'm wathing movies. Making a script that alters adjustments in xorg.conf isn't the best solution - you'd have to restart X every time you want to watch a movie .
Cheers,
Daniel

I am forced to shut down computer after a few minutes of use because of pixelation that freezes up the monitor. Possible solutions?

I am forced to shut down iMac g5 after a few minutes of use due to pixelation which freezes up monitor. Any thoughts on solutions?

You may have a problem with the video chip.
Here is how to tell...
Shutdown your machine. Hold down the shift key. Poweron. Bootup will be longer.
Wait awhile while you harddrive is being checked.
An article on how to boot into safe mode.
http://support.apple.com/kb/ht1455
Runs OK in safe mode...
Running in Safe mode leaves out some video drivers. Which results in your machine not using advanced video hardware. As luck would have it, you can run the safe mode video drivers in normal mode.
Here is how:
https://discussions.apple.com/message/16057567#16057567
Look through the above thread. See the second page. You don't have to read through the first page. Just go to the part where I try a solution that works.
Summary of G5 problems. Includes instructions on a hardware fix for the brave at heart:
See -Rotten Apple- articles in both of these threads.
https://discussions.apple.com/thread/4023152?tstart=0
https://discussions.apple.com/message/18700825#18700825
Robert

Macbook keeps shutting itself off after upgrading to snow leopard

Hi everyone, I hope you can help me out as I am out of ideas! After be assured that I could upgrade my late 2006 intel based macbook (10.5.8) to snow leopard, I bought the disc and tried to install. Everytime I tried, it shut itself down. I wiped the hard drive clean and tried again. Still happened. Finally after 14 hours of attempts, something finally stuck and I had snow leopard. I then tried to get all the updates and it kept shutting down. I tried to migrate my files from time machine and it shut itself down. Fed up, I tried to go back to leopard, but the computer won't stay on long enough to complete this. I wiped the hard drive clean again and now it won't stay on long enough to get to the start up page! HELP! I tried starting up in safe mode and it won't work. I've run disc utility several times and it says everything is OK. Now I have a blank hard drive on a computer that won't stay on for more than 5 minutes. Any insight would be greatly appreciated, otherwise I got to take it in to an apple specialist as the apple store has already told me the refuse to work on it because it is older than 5 years!!!!

Try a PRAM reset
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound two more times.
Release the keys.

Macbook pro shuts itself off after startup

2 or 3 months ago my charger broke, I havnt used my macbook pro since then, until recently when I got a new charger. Now my Mac wont start up.
Or, it starts up then shuts itself down again, Please help!

Ill try leaving it charging for 12hours, altho it is fully charged now, atleast what the green battery lighting says.

Installed ios6.1.3 to iPad 3 now it keeps turning itself off after a few seconds and is not recognised by itune

Please help. My daughter has updated her iPad with iOS 6.1.3 and it now keeps crashing after a few seconds use..we have tried a rest and this doesn't help. Thx

From iPhone: Hardware Troubleshooting - http://support.apple.com/kb/TS2802
[Will not turn on, will not turn on unless connected to power, or unexpected power off]
1. Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
2. Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
3. Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
4. After at least 15 minutes, if:
      -The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
      -The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
      -Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
5. If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
      -If the display turns on, go to step 4.
      -If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.

Phone loses signal from carrier orange, when I do have signal when I use phone it cuts off after a few seconds

iPhone loses signal often with message no service , I have tried several times to reset it through iTunes and on the phone, still the same problem have phoned orange they say it's not a problem there end, I think maybe it's the phone ,when I do manage to get signal because it comes a goes I find I can't make calls or receive calls has any one else had this problem with iPhone 4 thanks john

Hi,
I purchased iphone4s in april 2012, people used to say why is your phone always switched off. when i visited apple store, they checked/disgnosed and told me that the signal is dropping and replaced the phone in july2012.
Recently, after march2013, i again visited the store and replaced the phone again.
now with the new peice, i am unable to get the calls, till recently i used to get calls for my job oppurtunities, but with the new replacement, i am unable to know, if it a problem with the phone or ishould move out of apple after all the embarasement for a year.
i have all the apple gadgets, but iphone4s really ***** my life.i have told them that i will pay the difference amount for iphone5, but the store guys says they cannot. with this problem, they now sold me a protection plan for 60 pounds.
I think, apple really ***** after steve jobs.if apple does not respond i am sure i will move to samsung 4

HT201401 my phone just went off for about 10 minutes....was dead

My phone just went dead for about 10 minutes....i plugged it into itunes...finally came back on but dont know if that had anything to do with it....i was tramatized!

I'd suggest taking it to apple. Warranty or no warranty.

My BOLD 9900 switches off after a few minutes of turning it on

I got this latest blackberry with the hope of enjoying the best of phone tech. Its been behaving well for 2 weeks and then it suddenly changed. It started switching itself off if I'm not playing music, videos or if I haven't connected it to ma PC. Its really making me angry for wasting money on this phone that I can't use freely. The problem with playing the media is that it results in fast battery drainage. I wiped the device software and installed software (info below):
smartphone (3G, Wi-Fi)
7.0 Bundle 2406 (v7.0.0.585, Platform 5.0.0.734). But the problem still persists!!! . What should I do to bring ma fone to normal?

Hey chiwala,
Welcome to the BlackBerry Support Community Forums.
I can definitely help you out.
I would suggest performing a reload of the software by force detection, follow the steps in this KB article: www.blackberry.com/btsc/KB10144
Let me know if you have any more questions.
Cheers.
-ViciousFerret
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Like! for those who have helped you.
Click Accept as Solution for posts that have solved your issue(s)!

Using the Cyclops speed camera app, the sound on my iPhone 4s switches off after a few minutes. Any ideas?

when using the Cyclops speed camera app the sound on my iPhone 4s switches off after a short while. If I close the app and reopen it, there's still no sound. If I restar the phone and open Cyclops I get sound "welcome to Cyclops" or whatever the greeting is. Has anyone got any ideas?

I've taken several Express devices apart in the past to experiment with them. The internal components warm up quite a bit in the first 10-15 seconds. They continue to heat up after this. It takes 3-4 minutes or so before the heat transfers to the outer case for dissipation.
Nothing is certain, but I'm 95% sure that this is your issue. But, trying to find a microscopic break in a circuit board trace is, as I mentioned, a real longshot. If you have the time and have done things like this before, it might be worth a shot.
I guess the bottom line is that even if this is not the issue, the device will still need to be replaced since Apple does not offer repairs. There are no software or firmware fixes for somthing like this.

HT201401 I Phone shuts itself off after a few minutes when docked to a compatable radio

Similar Messages

Maybe you are looking for