HT201412 I try to update IOS 6 to my ipad 2 and after half of the procedure stopped ... then I try to reconnected to the itunes and say "iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes". Can every
I try to update IOS 6 to my ipad 2/ wf/3g and after about half of the procedure stopped ... then I try to reconnected to the itunes and say "iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes". Can everyone help please. In the screen of iPad appears the itunes Logo and the cable of connectios. Can't do nothing!!!
Click restore in itunes.
Similar Messages
-
when i pluged my ipod classic 5g to PC then it shows “iTunes has detected an iPod in recovery mode. you must restore this iPod before it can be used with iTunes”?then after restoring the PIOD when IPod restarted then Itunes again detect the same ERROR.
If you are using XP, and you went through the procedure at the bottom of the previously linked document to change the iPod's assigned drive letter, and you also tried putting it into Disk Mode...
If you have not already, try shutting down your computer and disconnecting all USB devices, including hub. Start up with only standard keyboard and mouse connected. Just to be safe, put the iPod into Disk Mode again
http://support.apple.com/kb/HT1363
Run iTunes. Connect iPod to a direct USB port on computer. iTunes may prompt you about "recovery" and ask you to do a Restore. Try to do a Restore again. -
Ipod nano 2nd generation: I cant restore, says, itunes has detected an ipod in recovery mode, you must restore this ipod before it can be used with itunes
What do you mean you can't restore? It's asking you to restore...
B-rock -
I reboot the computer, deleted and restart itunes, change computer, change cable, check ping, check connection. need help
Step by step
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. iPad Recovery Mode on computer screen
8. Select "Restore iPad"...
9. Select "Restore and Update"
10. Extracting Software.
11. Preparing iPad for restore.
12. Waiting for iPad.
13. Verifying iPad restore...
14.Restoring iPad software.
15. Verifying iPad software.
16. Verifying iPad Restore...
17. Restoring iPad firmware...
18. Your iPad is restored to factory settings; keep iPad connected to computer
19. Activate iPad
20. Enter Apple ID and Password
21. Continue
22. Welcome to Your New iPad -
I have tried to update my Iphone 4S today to IOS 7.0.6 and now my iphone wont connect to itunes as it says that it is detected that it is in recovery mode and needs restoring. How do I restore it? I cannot get my phone on at all?
Click restore in itunes.
-
when I wanted to downloaded the new software the phone went of and in my computer saying iTunes has detected an iPhone in recovery mode. you must restore this iPhone before it can be used with iTunes,
my hone is off pls help i need to make calls as i use my phone for work ,
Many Thanks
kerrySo do what it says and restore the phone. Nothing else you can do.
-
ok, so i finally found my ipod. I pick it up and it asks me if i would like to download the latest ios6 software so i did. Then moments later it died, ran out of battery. So i pluged it into my computer via apple usb cord. Then this is what itunes says "iTunes has detected an iPod in recovery mode.You must restore this iPod before it can be used with iTunes". All i want is to get my notes from the utilites section there so important to
If i restore it will my notes still be there, i dont want to restore original settings or something like that .
please help me what do i do?You have to restore the iPod, no ifs, ands, or buts...
After iOS is installed you will be asked if you what to set it up as a new iPod or if you want to restore from a backup.
If you have a good backup you can restore that and you're good to go.
If you don't have a good backup, then you end up with a "clean" iPod.... -
I was updating my Ipads software when it just shut off. I turned on the i pad and it gave me this picture of the wire plugging in to itunes. i plugged it into i tunes and i got this message on itunes saying itunes has detected an ipad in recovery mode. you must restore this i pad before it can be used with i tunes. pleasssse help
iOS Recovery Mode -
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808 -
I'm having the same loop message appear when trying to sync my new Ipod Shuffle "Itunes has detected a device in recovery mode. You must restore this device before it can be used w/ Itunes".
I've restored several times but it keeps looping back to the same message. Turns out this message appeared with my last shuffle and I thought possibly the shuffle battery was depleted and it was time to get a new one.
any suggestions?If you restore from backup.
You should have made sure that everything was on your computer bef ore updating anyway. Did you fail to do that?
All pics taken with iphone should be imported to your computer regularly as you would with any digital camera, most especially before any update/restore/etc. Did you fail to do that? -
iTunes gives me the message that it has detected an iPod in recovery mode and that I need to restore the factory settings. When I click the "restore" button iTunes downloads the software. This is a 30 minute process. Once the download completes, I get the same message "iTunes detects an iPod in recovery mode....". I'm running Windows Vista and ZoneAlarm security software.
I've tried this restore function multiple times and still get the same results.
I've also tried resetting the iPod by holding the wake/sleep button and the Home button at the same time. The iPod turns on but shows the icons of a usb cable connecting to iTunes.
Any help would be greatly appreciated.This maybe yuor problem:
Restore loop (being prompted to restore again after a restore successfully completes)
Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. . -
I got the error message above when connecting my old 1st generation ipod to my new PC. My Mac laptop was stolen in a break in at my home, and I no longer have my music files stored anywhere else but this ipod. i don't want to restore it if this process will wipe all my music away. This might be a dumb question, but I am not very savvy with technology. how should i proceed?
If you proceed you will lose all of your music. You weren't using Time Machine on your laptop?
-
What does this message mean? "itunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with ITnes." How do I restore when every time I connect to my computer I get this message?
Perhaps the information in this Apple support article will help:
http://support.apple.com/kb/TS3694#error3004
Regards. -
I have windows 8 enterprise OS and iTunes ver. 10.5.0.142. I was upgrading my iPad to IOS 6.1.3. After finishing the upgrade my iPad Reboot and currently stucked-up in a plug-in screen and iTunes Logo. When I try to connect it to the iTunes pop-up message appear saying " iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes." In short, I push the restore button then another pop-up message appear saying " The iPad software update server could not be contacted. Make sure your network settings are correct and your network connection is active, or try again later." I tried many ways but still no luck. I repeatedly reboot the iPad and open the iTunes still the same problem. I try also to uninstall the iTunes and installed the lower version but still the same problem, I even check the firewall if the ITunes was block or My privileges is administrator to run the iTunes or even reset my winsock but the problem still remain. PLEASE HELP! Thank you in advance!!!
Turn off your firewall and antivirus software.
-
Went on a Vegas trip on Sept
11th. My iPad worked fine
before getting on the plane. In the hotel about 48hrs later I opened my iPad it
read the message: “iPad is disabled,
connect to iTunes.”
To my knowledge myself, nor anyone else has tried to access my device or
entered the password incorrectly 3 or more times.
I started by updating my iTunes account on my computer to the latest version.
Then multiple times I attempted
the “Use recovery mode”
steps.
e.g.
1. Turn off your device and leave it off.
2. Plug in your device's USB cable to a computer with iTunes.
3. Hold down the Home button on your device as you connect the USB
cable. Keep holding down the Home button until you see the Connect to iTunes
screen.
I received the message on my computer saying “iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes.”
I click the “Restore iPad” button.
During which time the progress bar on my computer’s iTunes
screen was moving very slowly and other times seemed like it wasn’t moving at
all. I would leave my two devices and attached by the cable and upon returning
I would find that the process would have ended before it had completed.
Initially I thought it was a connections issue because I was in remote
locations with slow internet servers. Since being home I have re-attempted the
process and have been able to fully complete the forced recovery but I will
receive a message saying:
“The iPad could not be restored. The disk you are attempting to use is full.
Removing files and emptying the recycle bin will free up additional space.”
What recycle bin is the message referring to? Obviously I CANNOT access any
data on the iPad itself. Just for the **** of it, I did empty my computers
recycle bin and re-attempted the forced recovery process but as I suspected it
did nothing for the iPad and I still received the same message: “The iPad
could not be restored. The disk you are attempting to …”
Please helpHere's a couple of Apple Support articles ...
Resolve iOS update and restore errors
If you can't update or restore your iPhone, iPad, or iPod touch -
I downloaded the update because why not. I then turned my iPad on and get the iTunes logo and a lightning cable picture. I plugged the ipad into my computer and opened iTunes.
The I got:
"iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes"
When I click restore it then says:
"Are you sure you want to restore the iPad "iPad" to its factory settings? All your media and other data will be erased, and the newest version of the iPad software will be installed.
iTunes will verify the resotre with Apple. After this process is complete, you will have the option to restore your contacts, calendars, messages and other settings."
I don't want to lose my media. I was never told to make a back up, I was never told the update would be this difficult.
Can I just revert back to how it was before?I downloaded the update because why not. I then turned my iPad on and get the iTunes logo and a lightning cable picture. I plugged the ipad into my computer and opened iTunes.
Then I got:
"iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes"
When I click restore it then says:
"Are you sure you want to restore the iPad "iPad" to its factory settings? All your media and other data will be erased, and the newest version of the iPad software will be installed.
iTunes will verify the resore with Apple. After this process is complete, you will have the option to restore your contacts, calendars, messages and other settings."
I thought okay, I'll just erase everything then. I get error 3004 when I try to restore.
I've tried disabling my security software, updating iTunes, replacing my hosts file and using a third party software recovery tool. Nothing works. I never thought Apple would break my iPad with an update but they managed to.
Any solutions?
Thank you.
Maybe you are looking for
-
How to address form controls in jsp page
Hello, I have a very stupid question. How do i empty the textfield value in my jsp page. I know that i can make a function that does that. but i dont know how to adress the control. Its got to be something like txtfield.setValue("myvalue") but i just
-
One project published with two stage sizes and shapes?
I've got one project that must be deployed in two different size & shape layouts, online running in a 760 x 700 box (almost square) and also on a wide screen kiosk running 1120 x 700 (wide rectangular). Maintaining two separate layouts has been time
-
Playing .pps file using QT PRO
I'm new with mac. I've received a PowerPoint slideshow file with sound. Try Keynote. Slides fine, but not sound. Using a PowerPoint trial version I was able to find out that there's a wav file embedded in one of the slides. So I saved as QT format fi
-
Finding the right htmlBusiness page
Hi, we are on WAS 700 with internal ITS. I am dealing with SRM EBP templates and I can't find the right htmlBusiness source . From the html source code of the page rendered in the webbowser I get the info that my page is <!-- This page was creat
-
Why did all my pictures disappear? How can I get them back?
Every picture in my library disappeared how can I get them back?