HT201412 My Ipod touch turns on, shows Apple logo, shut down, and again turn on , Apple logo and so on.

once you press the on button, the ipod start the loop:
1. black screen with apple logo for about 10 secondes
2. turn off
(back to 1)
thanks for helping

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar       

Similar Messages

  • I ipod touch is not showing up on my computer when I plug in to update and download audiobooks.

    I ipod touch is not showing up on my computer when I plug in to update and download audiobooks.

    Hey khdewey,
    Thanks for the question. I understand you are experiencing issues with your iPod touch being recognized in iTunes on your Mac. The following resource may provide a solution:
    iOS: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/ts1591
    Note: This article is for Mac OS X users. If you're using a Windows PC, please refer to these troubleshooting suggestions.
    Follow these steps to resolve your issue:
    1. Ensure that your Mac meets the minimum system requirements for your iPhone, iPad, or iPod touch.
    2. Install software updates on your Mac.
    Note: If an iTunes update is available, apply the update.
    3. Check USB connections. iOS devices require USB 2.0 to function properly. If you're not sure your Mac has USB 2.0 ports, refer to the computer's specifications.
    4. Disconnect other USB devices and connect your device directly to a USB port on your Mac.
    5. Restart your Mac.
    Additional Information
    In rare circumstances, your device may be recognized after reinstalling iTunes, but after you restart your Mac, the device may not be recognized again. If this happens and you're using Mac OS X v10.6 Snow Leopard, please follow these steps.
    Thanks,
    Matt M.

  • 15" i7 Macbook Pro from early 2011.takes the mac laptop two or three tries to boot successfully. It would turn on, show gray screen, shut down, turn on again, show gray screen, shutdown, and then turn on, show gray screen, before it can finally get

    Hello All,
    I have a 15" i7 Macbook Pro from early 2011. The past few weeks, it has been getting increasingly difficult to get on my computer. It takes the mac laptop two or three tries to boot successfully. It would turn on, show gray screen, shut down, turn on again, show gray screen, shutdown, and then turn on, show gray screen, before it can finally get to the dark gray log-in screen. Even when I finally get logged in to start working, thinking it would be okay now, it shuts down randomly.
    I've ruled out the possibility of a software problem because I've just done a clean re-install of Mac OS X Mavericks on my computer just yesterday.
    I did upgrade the RAM recently, about a month and a half ago, from 4GB to 16GB, I went to the apple store four days after that upgrade to have them do a hardware test, and clean the inside of my laptop, which helped with previous heat issues. When they did the hardware test, the hardware was all registered as fine from their system.
    I've tried resetting the SMC, PRAM, and doing the internet recovery hardware test, but to no avail. I thought I could at least find out what parts needed to be replaced from the hardware test but it seems that when the hardware test is almost finished, the computer just shuts down, So I am unable to see the results.
    My computer is also having battery issues, under battery condition, it says "replace now," parts have been ordered, waiting for arrival. But if the battery health is low, it should still boot up fine, it would just hold a significantly less charge.
    Could this be a hard drive issue?
    Has anyone had similar symptoms and how was it resolved?
    Does anyone know what I can do to alleviate this issue?
    I haven't had time to take it to Apple because I'm currently taking a 21 credit semester academically. I'm an art and design student so my computer is basically the bane of my existence. Help! Any constructive advice is welcomed!
    Thank you so much for your input!
    -Christina C.

    Problem description:
    The Hard Disk is failing.
    EtreCheck version: 2.0.11 (98)
    Report generated November 4, 2014 at 7:59:28 AM EST
    Hardware Information: ℹ️
      MacBook Pro (15-inch, Early 2011) (Verified)
      MacBook Pro - model: MacBookPro8,2
      1 2.2 GHz Intel Core i7 CPU: 4-core
      16 GB RAM Upgradeable
      BANK 0/DIMM0
      8 GB DDR3 1600 MHz ok
      BANK 1/DIMM0
      8 GB DDR3 1600 MHz ok
      Bluetooth: Old - Handoff/Airdrop2 not supported
      Wireless:  en1: 802.11 a/b/g/n
    Video Information: ℹ️
      Intel HD Graphics 3000 - VRAM: 512 MB
      Color LCD 1440 x 900
      AMD Radeon HD 6750M - VRAM: 1024 MB
    System Software: ℹ️
      OS X 10.9.5 (13F34) - Uptime: 0:3:43
    Disk Information: ℹ️
      TOSHIBA MK7559GSXF disk0 : (750.16 GB)
      S.M.A.R.T. Status: Verified
      EFI (disk0s1) <not mounted> : 210 MB
      HDV4 (disk0s2) /  [Startup]: 749.30 GB (712.10 GB free)
      Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
      MATSHITADVD-R   UJ-898 
    USB Information: ℹ️
      Apple Inc. FaceTime HD Camera (Built-in)
      Apple Inc. BRCM2070 Hub
      Apple Inc. Bluetooth USB Host Controller
      Apple Inc. Apple Internal Keyboard / Trackpad
      Apple Computer, Inc. IR Receiver
    Thunderbolt Information: ℹ️
      Apple Inc. thunderbolt_bus
    Gatekeeper: ℹ️
      Mac App Store and identified developers
    Kernel Extensions: ℹ️
      /Library/Application Support/Avast/components/fileshield/unsigned
      [loaded] com.avast.AvastFileShield (2.1.0 - SDK 10.9) Support
      /Library/Application Support/Avast/components/proxy/unsigned
      [loaded] com.avast.PacketForwarder (1.4 - SDK 10.9) Support
    Launch Agents: ℹ️
      [not loaded] com.adobe.AAM.Updater-1.0.plist Support
      [loaded] com.avast.userinit.plist Support
    Launch Daemons: ℹ️
      [invalid?] com.adobe.SwitchBoard.plist Support
      [loaded] com.avast.init.plist Support
      [loaded] com.avast.uninstall.plist Support
      [loaded] com.avast.update.plist Support
      [invalid?] com.perion.searchprotectd.plist Support
    User Launch Agents: ℹ️
      [invalid?] com.avast.home.userinit.plist Support
      [loaded] com.google.keystone.agent.plist Support
      [invalid?] com.jdibackup.ZipCloud.autostart.plist Support
    User Login Items: ℹ️
      None
    Internet Plug-ins: ℹ️
      AdobePDFViewer: Version: 10.1.1 Support
      QuickTime Plugin: Version: 7.7.3
      JavaAppletPlugin: Version: 14.9.0 - SDK 10.7 Check version
      Default Browser: Version: 537 - SDK 10.9
    User Internet Plug-ins: ℹ️
      TroviNPAPIPlugin: Version: 1.0 - SDK 10.9 Support
      Google Earth Web Plug-in: Version: Unknown
    Safari Extensions: ℹ️
      Avast Online Security
      Trovi Search for Safari
    3rd Party Preference Panes: ℹ️
      None
    Time Machine: ℹ️
      Time Machine not configured!
    Top Processes by CPU: ℹ️
          16% mds
          7% WindowServer
          1% loginwindow
          1% fontd
          1% com.avast.daemon
    Top Processes by Memory: ℹ️
      120 MB com.avast.daemon
      86 MB Google Chrome
      52 MB Finder
      52 MB WindowServer
      41 MB Google Chrome Helper
    Virtual Memory Information: ℹ️
      13.45 GB Free RAM
      1.34 GB Active RAM
      944 MB Inactive RAM
      1.43 GB Wired RAM
      1.11 GB Page-ins
      0 B Page-outs

  • My home was burglarized, ipod touch stolen can it be blocked shut down....anything?

    is thier any way my ipod- touch can be shut down, blocked........ anything done so these SOB cant get into personal info?

    No.
    - If you previously turned on FIndMyiPod on the iPod in Settings>iCloud and wifi is on and connected go to iCloud: Find My iPhone, sign in and go to FIndMyiPhone. If the iPod has been restored it will never show up.
    - You can also wipe/erase the iPod and have the iPod play a sound via iCloud.
    - If not shown, then you will have to use the old fashioned way, like if you lost a wallet or purse.
    - Change the passwords for all accounts used on the iPod and report to police
    - There is no way to prevent someone from restoring the iPod (it erases it) using it unless you had iOS 7 on the device. With iOS 7, one has to enter the Apple ID and password to restore the device.
    - Apple will do nothing without a court order                                                        
    Reporting a lost or stolen Apple product                                               
    - iOS: How to find the serial number, IMEI, MEID, CDN, and ICCID number

  • My iPod touch automatically I get the message "Shut down" red

    I hope you can solve this problem. Often an application I'm using the iPod and automatically receive an option to "Off" (red) or try to turn it off manually is not an option but after several attempts, and frequently also automatically locks. What should I do?

    Try the standard fixes to rule out a software problem:
    - Reset. nothing will be lost.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup
    - Restore to factory defaults/new iPod.

  • It's amazing how just after my garantee on my Ipod touch ran out, now it keeps shutting down or locking on me. I have restored it several times. Any ideas anyone?

    It is amazing how just as the warranty on my Ipod touch runs out, it has started to shut down on me or freezes. Any ideas anyone?

    If you restore the iPod to factory defaults/new iPod and still have the problem then you likely have an hardware problem and the Genius Bar is a good option.

  • How to fix a frozen ipod touch, it only shows the apple logo?

    How do you fix  a frozen ipod touch, it only shows the apple logo?

    Hello,
    I have same broken iPod Touch 4G, I'm stuck on the Apple logo and only what I can do is just restart. If I connect iPod turns on but that's all. I checked a lot of tricks how to restart/reboot device and how to get DFU but I have only the logo. iTunes on my mac can't recognize the device.
    And in Apple retail store the guy told me: sorry it's dead. We can fix for about £200. After 1 month when my waranty is finished. Funny isn't it? I can't believe that my lovely iPod is dead after 13 months. Where is the "for quality you have to pay." Is it conspiracy if you don't buy extra waranty we will send you killing signal into your iDevice?
    Many thanks for help

  • My ipod touch 4th gen shows that it is connected to a wifi network but when i try to browse safari it doesnt work.please help me out.

    My ipod touch 4th gen shows that it is connected to a wifi network but when i try to browse safari it doesnt work.please help me out.
    I am using wifi from a mobile by using the tethering option.

    Hi there amalrockzz,
    You may find the troubleshooting steps in the article below helpful.
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Follow these steps to troubleshoot the above issues:
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your Wi-Fi setting is dimmed, follow these steps.
    Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
    Tap  and Forget this Network.
    Try to connect to your desired Wi-Fi network.
    Note: You may need to enter your Wi-Fi password again if your network requires one.
    Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
    Unable to access the Internet while connected to Wi-Fi
    If you're using a public or commercial network, you may need to log in or subscribe.
    Check to see if you have a self-assigned IP address:
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected and tap .
    If your IP address is 169.254.xxx.xxx, you may not be able to access the Internet.
    If you do not have a self-assigned IP address, see if other Wi-Fi devices on your network have Internet access.
    If they do not, consult with your network administrator or ISP for further assistance.
    If they do, reset network settings on your device by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
    previously connected Wi-Fi networks and passwords
    recently used Bluetooth accessories
    VPN and APN settings
    Additional Information
    Find information on connecting to a Wi-Fi network.
    Some third-party routers may not be compatible with all iOS devices, even after updating to the latest firmware. If your iOS devices can successfully connect to other Wi-Fi networks, contact your router's manufacturer to ensure that your router is compatible with your iOS device.
    See recommended settings for configuring your Wi-Fi router for use with iOS devices.
    -Griff W. 

  • My ipod touch is not showing up on the source list

    My iPod Touch is not showing up on the source list. I have tried to restore the ipod, i have uninstalled, reinstalled, and used the repair option in the control panel to no avail. I am currently useing the latest version of Windows 8 on an Asus VivoBook. What can i do to fix the problem?

    Hello dbar2530,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/ts1538
    Best of luck,
    Mario

  • My iphone 5 and 2 ipod touches will not show up on my itunes

    My iphone 5 and 2 ipod touches will not show up on my itunes when i connect them to my laptop.  I have tried different cables, restarted the mobile thing, uninstalled and reinstalled itunes, it is only on my laptop that has Windows 8. My dekstop with Windows 7 is fine will recognize them.  This has been going on for over a week.. What is going on?

    Hello Jennifer,
    The following article provides some useful troubleshooting that can help get your iPhone and iPods to reappear in iTunes.
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    Cheers,
    Allen

  • I have several albums by and an artist as is expected for a number of artists. But after the new iOs5 update my ipod touch now only showing one on my ipod.

    I have several albums by and an artist as is expected for a number of artists. But after the new iOs5 update my ipod touch now only showing one on my ipod. I have already resynced it, any suggestions on how to fix the problem without having to restore my iPod to factory settings.

    Becaise the digitizer is broken in that area
    Apple will exchange your iPod for a refurbished one for $199 for 64 GB 4G and $99 for the other 4Gs. They do not fix yours.
    Apple - iPod Repair price                       
    A third-party place like the following maybe less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens         
    Replace the screen yourself if you are up to it
    iPod Touch Repair – iFixit                  

  • IPod Touch is not showing up in My Computer

    I realize that there are several other topics that talk about this problem, but so far none have really helped me. My goal is to have my iPod Touch be recognized as a camera so I can upload all my photos from my Saved Photos to my computer and finally clear up some much needed space on it. Please don't refer me to software that will allow me to move photos from my iTouch to my PC because either they are all only trial versions or they don't allow me to access the images from my Saved Photos album.
    Currently my iPod Touch does not show up in My Computer. I'm running Windows XP. Checking my Device Manager for the driver, the only driver that comes up that relates to my iPod is called Apple Mobile Device USB Driver. I've tried uninstalling and reinstalling that driver (and one I was able to get the iPod to show up in My Computer as a camera but when I clicked on it, it said that there were no pictures in the device [and I clearly do], and after uninstalling the driver again and reinstalling it the icon went away). I've read that maybe uninstalling iTunes and then reinstalling it might fix my problem, but I'm weary to uninstall it for fear that I might loose all my applications that I've synced into iTunes as well as my purchases and all the movies and things I've downloaded.
    If anyone has any comments, suggestions, or further questions about my problem, PLEASE say so because this is very urgent and I need all the help I can get.

    Also, I forgot to add that my iTouch is a 1st Gen I believe (I'm sorry, I got it for a Christmas gift, but I'm pretty sure it's a 1st Gen).

  • I updated to a newer version of iTunes and now my ipod touch does not show up as a device in iTunes.  There is no 'Devices" category on the bar at the left

    I updated to a newer version of iTunes and now my ipod touch does not show up as a device in iTunes.  There is no 'Devices" category on the bar at the left

    Refer to this article:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538

  • My ipod touch is not showing in itunes therefore, not syncing. I've gone through the trouble shooting steps about 5 times.

    My ipod touch is not showing in itunes therefore, not syncing. I've gone through the trouble shooting steps about 5 times.

    Did you try here:
    iOS: Device not recognized in iTunes for Mac OS X
    If you  have iTunes 11 turn on the Sidebar. Go to iTunes>View and click on Show Sidebar. You can also do a Crtl+S to show the sidebar. The sidebar is where Devices appears. and Control+B to show the Menu bar
    Next try on another computer to help determine if you have an iPod or computer problem.

  • My iPod touch won't show up on iTunes but my iPhone does, My iPod touch won't show up on iTunes but my iPhone does

    My iPod touch doesn't show up in iTunes but my iPhone does help

    See
    iOS: Device not recognized in iTunes for Windows
    - I would start with
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    or              
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
    - New cable and different USB port
    - Run this and see if the results help with determine the cause
    iTunes for Windows: Device Sync Tests
    Also see:
    iPod not recognised by windows iTunes
    Troubleshooting issues with iTunes for Windows updates

  • Ipod touch 4 isnt showing on itunes. PLEASE HELP

    hey everyone
    my new ipod touch 4 isnt showing up on itunes i have the latest itunes installed and im not sure why it isnt working.
    it used to show up fine since i have had it for about 2weeks and then i tried to restore it and it has stopped showing up
    PLEASE HELP!!!!!
    thanks,
    lincoln

    This Support article might help you:
    http://support.apple.com/kb/ts1369
    Michael

Maybe you are looking for

  • How can I use a labview VI as a CVI instrument driver

    I have a VI for the Keithley 485 that would like to convert into a form usable by CVI. I don't have labview so I cannot generate a DLL based on the VI.

  • DW CS3 Training wish list - need suggestions

    My company has asked if I'd like any online/book training for the new version of Dreamweaver CS3. What have you found to be the most concise and worthwhile? Any suggestions for instructor led or conferences that you felt were "a must"? Thanks!

  • DIADEM 9.1 / NI-DAC-6251

    DIADEM 9.1 / Ni-DAC-6251. I have to read 2 AC-Analog-Voltage with the DAQ-Card, and analize the signals with the Diadem software. My problem is, to configure a ramp (0 to 10V) as OUTPUT-Signal with the DIADEM Software, and to transfert this one on th

  • DOS batch command to call Hyperion workspace reporting batch job

    Hello, Is there any method to call the batch job in hyperion workspace for exporting report ? i would like to call the job batch by DOS batch. Is it possible? thanks Gary

  • Partial forge shows "missing property"

    Hi, My partial forge log shows: UpdateAdapter 'PartialUpdateAdapter': record 2255 is missing property ''; using previous value, ''. How do I find out which property is missing? In my Appconfig, I have <arg>-vd</arg> specified for the Partial Forge co