HT201413 Iphone4 update restoring . Plese advise what is error 21 and error 11
Iphone4 updating & restoring . Plese advise what is error 21 and error 11
Read about errors here http://support.apple.com/kb/ts3694
Similar Messages
-
Iphone4 restor and update. Plese advise what is error 21 and error 11
Iphone4 restore and update . Plese advise what are error 21 and error 11 ?
Read about errors here http://support.apple.com/kb/ts3694
-
My iPhone 4 fail to update to iOS 5 and now it can't restor the firmware I am geting and error it says The iPhone "iphone" could not be restored. An unknown error occurre (-1) . Plese help
My iPhone 3GS is getting the same error. I've called Apple a bunch of times, and they won't get back to me. I'm searching through discussions to figure out a solution.
-
When I try to update my ipad to IOS6 I get and error 6 message. Any idea what that means and how to fix it? I tried updating via Itunes and also normal download.
What model iPad and what version of iOS is it currently running?
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Update and restore alert messages on iPhone, iPad, and iPod touch
http://www.buybuyla.com/tech/view/012953a0d412000e.shtml
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
Cheers, Tom
Error 2, 4 (or -4), 6, 1000, 9006
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
There may be third-party software that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your registry. Your default packet size being set incorrectly can cause these errors. Contact the manufacturer of the software that installed the packet size modification for assistance or follow this article by Microsoft: How to reset Internet Protocol (TCP/IP).
Verify that access to ports 80 and 443 are allowed on your network.
Verify that communication to albert.apple.com or photos.apple.com is not blocked by a firewall, or other Internet security setting.
Discard the .ipsw file, open iTunes and attempt to download the update again. See the steps under Advanced Steps > Rename, move, or delete the iOS software file (.ipsw) below for file locations.
Restore your device while connected to a different network.
Restore using a different computer.
Message was edited by: Texas Mac Man -
i am not able to update & restore my iphone 3G,it is showing error no 1015,kindly infm what to do?
Your phone is jailbroken/hacked. You cannot receive assistance on this forum. Go somewhere else for help.
-
HT1212 When you restore an iphone, what is lost and what remains the same
When you restore an iphone, what is lost and what remains on the phone?
IF you restore as new all data and settings are lost. IF you restore from a backup then the phone willbe the same as it was as the phone from which the backup came
This is what is contained in a backup
iTunes will back up the following information
Contacts* and Contact Favorites (regularly sync contacts to a computer or cloud service such as iCloud to back them up).
App Store Application data including in-app purchases (except the Application itself, its tmp and Caches folder).
Application settings, preferences, and data, including documents.
Autofill for webpages.
CalDAV and subscribed calendar accounts.
Calendar accounts.
Calendar events.
Call history.
Camera Roll (Photos, screenshots, images saved, and videos taken. Videos greater than 2 GB are backed up with iOS 4.0 and later.)
Note: For devices without a camera, Camera Roll is called Saved Photos.
Game Center account.
Home screen arrangement.
In-app purchases.
Keychain (this includes email account passwords, Wi-Fi passwords, and passwords you enter into websites and some other applications. If you encrypt the backup with iOS 4 and later, you can transfer the keychain information to the new device. With an unencrypted backup, you can restore the keychain only to the same iOS device. If you are restoring to a new device with an unencrypted backup, you will need to enter these passwords again.)
List of External Sync Sources (MobileMe, Exchange ActiveSync).
Location service preferences for apps and websites you have allowed to use your location.
Mail accounts (mail messages are not backed up).
Installed Profiles. When restoring a backup to a different device, installed configuration profiles are not restored (such as accounts, restrictions, or anything which can be specified through an installed profile.) Any accounts or settings that are not associated with an installed profile will still be restored.
Map bookmarks, recent searches, and the current location displayed in Maps.
Microsoft Exchange account configurations.
Network settings (saved Wi-Fi hotspots, VPN settings, network preferences).
Nike + iPod saved workouts and settings.
Notes.
Offline web application cache/database.
Paired Bluetooth devices (which can only be used if restored to the same phone that did the backup).
Safari bookmarks, cookies, history, offline data, and currently open pages.
Saved suggestion corrections (these are saved automatically as you reject suggested corrections).
Messages (iMessage and carrier SMS or MMS pictures and videos).
Trusted hosts that have certificates that cannot be verified.
Voice memos.
Voicemail token. (This is not the voicemail password, but is used for validation when connecting. This is only restored to a phone with the same phone number on the SIM card).
Wallpapers.
Web clips.
YouTube bookmarks and history.
* Your contacts are part of the backup to preserve recent calls and favorites lists. Back up your contacts to a supported personal information manager (PIM), iCloud, or another cloud-based service to avoid any potential contact data loss. -
"PSA error" and "error 6 in the update" ...VERY IMP!!
Hi All,
I am facing this very strange and critical problem.
Delta load failed due to "PSA error" and "error 6 in the update" for two Infosources.
The Infosource 1 ( Header)- I was able to successfully edit the PSA error and update the delta from the PSA to the ODS....problem solved
The Infosource 2 ( Item ) - The delta for this request is sent to from this Infosource to ODS's .It is allowing me to edit the PSA data and save it. But even after editing and saving, when I am updating the delta to the ODS the request goes red. When I see the reason, I find the same "error in the PSA "and the" Error 6 int he Update". Looks like the edited data is not getting saved.
The error in PSA was ..date was wrongly entered with wrong year in it. So therefore it clashes witht he fiscal yr variant for that infosource.
Tried to do repeat delta for the next delta. Same issue.
__1. No clue why the edited data is not getting saved__
__*2. What is this " error 6 in the Update"*_
In the Status tab of monitor of that request:_
Error message when processing in the Business Warehouse
Diagnosis
An error occurred in the SAP BW when processing the data. The error is documented in an error message.
System response
A caller 01, 02 or equal to or greater than 20 contains an error meesage.
Further analysis:
The error message(s) was (were) sent by:
Update rules
Update rules
Second step in the update
Procedure
Check the error message (pushbutton below the text).
Select the message in the message dialog box, and look at the long text for further information.
Follow the instructions in the message.
Please provide a solution. Very critical and important issue.I got the same PSA error for another Header Infosource which updates data to one ODS, for which i could edit the data and then update the edited data into the ODS. The changes i have done are saved and had no issue with the infosource. and the load is successful.
But for this Item Infosource ( updates data to two ODS) , i got the same PSA error( Date entered worng) , i was able to edit the data in the PSA and save. but after editing and saving when i update teh request( after editing PSA) the request goes RED ( which means the i get the old values..wrong data).
Why am I not able see the changes i have done when i update the delta from PSA to ODS after editing?....really strange.
Is there any problem in the update rules or something for this Infosource( not sure)..becos i am gettng this "error 6" in the Update.
Please Rescue! -
I have an iMac G4 PowerPC with OS 10.5.? After deleting 17G of music files to make room on the 74G drive, The iPhoto and iWeb updates seemed to load okay, but the OS 10.5.8 update failed - message opened said the computer encountered an error and must shut down. Now I get the blue screen. Startup with 'V' pressed shows multiple lines saying: error-can't find IntelCPU Power Manager. What now?? I reset PRAM, I think.....?????
I am concerned that you might have applied a system updated intended for an Intel iMac, while you have a PPC (non-Intel) iMac. Your PPC OS should not be looking for an "IntelCPU Power Manager."
Have you tried booting from the 10.5 install DVD/CD and repairing the hard drive, plus repairing permissions?
If you done the repairs mentioned above, and your problem still persists, you can also try doing a safe boot. (see http://support.apple.com/kb/HT1455 ) Then, if none of these things worked, if I were in your shoes (it's hard to diagnose these things without being there in person) I would first check that there is adequate disk space, then I would boot from the 10.5 DVD/CD install disk and reinstall the operating system. There is an option to do an archive and install preserving user files/settings, that would be the option you want, as it will save your files but install a new OS. Make sure you have a good backup of your files first. If you do not have one, use "target mode" to copy all your files before embarking on an new OS install. Assuming that you do succeed with this install, then use Software Update to get the right updates for your iMac. -
AUSST - Update Server issue: IIS7 406 errors, and ERROR: Invalid webfeed
I spent today configuring and installing an instance of the AUSST2.0 software, following http://www.adobe.com/content/dam/Adobe/en/devnet/creativesuite/pdfs/Up dateServerSetupTool_TechNote.pdf
Here's where I am:
Via Firefox/IE I get the following when browsing to the Updaterfeed.xml:
XML Parsing Error: syntax error
Location: <SERVER LOCATION>
Line Number 1, Column 1:
0001
^
Which I expect is ok... the server is sending the updaterfeed.xml. I can also download the updates directly through IE or Firefox. The corresponding entry in the IIS log is:
/AdobeUpdate/webfeed/oobe/aam20/win/updaterfeed.xml - 80 - <MY IP ADDRESS> Mozilla/5.0+(Windows+NT+6.1;+WOW64;+rv:9.0.1)+Gecko/20100101+Firefox/ 9.0.1 304 0 0 196
When I attempt to do an update via Photoshop, I receive:
"The update server is not responding. The server might be offline temporarily, or the internet or firewall settings may be incorrect. Please try again later. Error Code: U41M1C213 "
This happens regardless of firewall status locally or on the server. Other communication to the server is fine.
the aamu.log on level 10 says:
2012-01-17T20:01:52: Entering slurpURL: (http://<SERVER IP>/AdobeUpdate/webfeed/oobe/aam20/win/updaterfeed.xml) bytesPushed
2012-01-17T20:01:52: main download loop - waiting for network availability
2012-01-17T20:01:52: have network connection
2012-01-17T20:01:52: connected to: = http://<SERVER IP>/AdobeUpdate/webfeed/oobe/aam20/win/updaterfeed.xml
2012-01-17T20:01:52: received status code from server
2012-01-17T20:01:52: slurpURL: (http://<SERVER IP>/AdobeUpdate/webfeed/oobe/aam20/win/updaterfeed.xml) bytesPushed = 0
2012-01-17T20:01:52: CFU(Webfeed): dumping webfeed: C:\Users\<MY USERID>\AppData\Local\Adobe\AAMUpdater\1.0\Data\webfeed.xml
2012-01-17T20:01:52: CFU(Webfeed): ERROR: Invalid webfeed. Could not read webfeed sequence number.
2012-01-17T20:01:52: UCGetprogress : (B) Returning with value = 1
2012-01-17T20:01:52: UCGetprogress : Check for updates returning state for reffId =
2012-01-17T20:01:52: UCGetprogress : Check for updates returning state = 41
2012-01-17T20:01:52: UCGetprogress : Check for updates returning outError = 213
2012-01-17T20:01:52: UCGetprogress : Check for updates returning percent = 0
2012-01-17T20:01:52: UCGetprogress : Check for updates returning unique error code string = U41M1C213
2012-01-17T20:01:52: UCGetprogress : (D) Returning with value = 1
2012-01-17T20:01:52: Stepped into << UCGetUserPreferences >> call.
2012-01-17T20:01:52: Returning from << UCGetUserPreferences >> call with return value - = 1
The subsequent IIS Log entry for this is:
GET /AdobeUpdate/webfeed/oobe/aam20/win/updaterfeed.xml - 80 - <MY IP ADDRESS> AAM+Updater+1.0 406 0 0 19
I've added the <add name=”SSINC-xml” path=”*.xml” verb=”*” modules=”ServerSideIncludeModule” resourceType=”Unspecified”> to my web.config, per http://blogs.adobe.com/oobe/2010/09/enterprise-in-house-update-hosting -for-cs5.html
I continue to get the U41M1C213 error whilst updating. I can get the updates when I remove the AdobeUpdater.Overrides from C:\ProgramData\Adobe\AAMUpdater\1.0 (Win7)
Help?I was directed here by another adobe employee. http://forums.adobe.com/thread/950769
I'll try again.... here is the current thread. http://forums.adobe.com/thread/951039 -
HT201413 I cant restore my iPad what can i do?
What i Have to do?
It actually doesn't matter if the Find My iPhone app is on your iPad.
What matters is whether you turned Find My iPhone on on your iPad in Settings > iCloud. if you did, you can track it. If not, you cannot.
See http://support.apple.com/kb/HT5668 -
Help
Try a forced reboot. Press and hold BOTH the home and power buttons at the SAME time until you see the Apple Logo, then let go of both buttons and your iPad will restart. You won't lose any settings or data.
-
please help me i have to recover my iphone it has now gone to recovery mode ........
Follow the steps in this knowledge base article first, if that doesn't help then lick on the specific error code 3014 and that will lead you to another page for resolution.
-
I am sorry I waited since it came out as I was sure I would get into trouble but I did it, such a relief...
If you are not careful, you will be banned from this forum for having no complaints in your post.
-
I have just updated my ITunes software to the latest as prompted. I purchased songs as wanted and then closed it down and have been billed accordingly. Since trying to open ITunes again. I have been met with the message saying This version of Itunes may be corrupted or not installed properly. Reinstall I Tunes.
Please advise what has happened and what I need to do (using windows 7)Let's try a repair install of iTunes.
Restart the PC first.
If you're using Vista or 7, now head into your Uninstall a program control panel, select "iTunes" and then click "Repair".
If you're using XP, head into your Add or Remove Programs control panel, select "iTunes", and click "Change". Select "Repair" and click "Next" as per the following screenshot:
Can you launch your iTunes now? -
i went to update my ipod touch and restore it. it was working fine and then when it it restarted itself it it stuck onone scren te same one when u first get it, it will not do anythig elts what do i do please help i whont my ipod touch back
Restore loop (being prompted to restore again after a restore successfully completes): This issue is typically caused by out-of-date or incorrectly configured third-party security software. Please followTroubleshooting security software issues if USB troubleshooting does not resolve this issue.
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.
Error 50: This error (and error -50) are timeout errors. Follow the steps for errors 13 or 14 above.
Above from:
http://support.apple.com/kb/TS3694
Maybe you are looking for
-
How do I get rid of "Windows No Disk Exception Processing Message c0000013 Parameters 75b6bf7c 4 75b6bf7c 75b6bf7c" when firefox starts up, I have to hit continue twice to get past this error message. Then all is OK. The solution shown for this threa
-
File Transfer Between Mac Mini and Beige G3 OS 9?
I'd like to transfer files between a PPC Mac Mini with 10.4.x (Bluetooth and Airport) and a Beige G3 still running OS 9 which has USB and FW ports added. I ccould use a USB stick and be happy, but on the Mini that makes my USB modem hang up. I'd rath
-
Data at the client's is kept in two complementary databases that need to be consolidated in one report (P&L, Cash Flow,Balance Sheet).Currently, reports on separate databases is possible but they would like financial reports to incorporate accounts
-
Identifiers tab of the Communication Channel
Can any one explain me about, <b>Identifiers tab of the Communication Channel</b> in the context of both A2A and B2B scenarios. Thanks, -Naveen.
-
How to Print Euro Currency Symbol
Hi All, Please suggest how to Print Euro Currency symbol in SAP Script. Thanks Saurabh