HT201415 iPhone is unable to access into internet use wi-fi connectoins
Hi,
When use Wi-Fi connections sometimes can't get access to the network. Phone get ip and successfully connected to Access Point.
Use Wi-Fi Router: D-link DAP-2310
I won't be able to find out for a to maximum of 72 hours regarding why I can't connect to the xfinity hotspot. I won't be at the location I'm the at now for the next 72 hours.
As a temporary workaround, I signed up for a free one hour trial of internet service by being a 'new member.' That will have to do for now.
Similar Messages
-
When my iphone connects to wifi, everything else in my house will not connect to the internet. They all show 3 to 4 bars on connection strength, but unable to access the internet. The second I turn off the wifi on my iphone, everything in my house runs fine. What is going on?
Had a similar problem a number of years ago with a laptop my daughter had. The probelm turned out to be the router. What kind of router do you have? Have you checked for firmware updates, or at least tried re-booting it?
-
Unable to access the Internet over 3G Network, Wi-Fi fine.
Hi there,
I'm unable to access the internet on the iPhone 3G over the 3G network. Wi-Fi is fine, no problems there, but every time I try to bring up a website in Safari over 3G I get the message "Safari can't open the page because it is not connected to the Internet".
I have Enable 3G 'ON' under Settings > General > Network, and I have full strength on the signal meter in the top left of the Home screen. I'm in a city (Melbourne, Australia) on the Optus network, so the network itself shouldn't be the issue.
I've tried resetting the Network Settings under Settings > Reset > Reset Network Settings, but it didn't change anything. Any other ideas?
Cheers.Well, there you go, fixed! Called Optus Customer Service and they were actually helpful! Apparently there were "some components in their back-end that needed to be installed manually." The man wasn't sure why they weren't there, "glitches, blah, blah..." but at least they're there now and I have 3G access.
-
UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION
Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn . -
After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work.
After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work.
-
Users unable to access the internet sites
Hi Everyone,
We have users who are able to get the IP address but unable to access any internet sites.
I check the trap logs on the WLC
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 16) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
RADIUS server 192.168.60.1:1812 deactivated on WLAN 1
RADIUS server 192.168.60.1:1812 failed to respond to request (ID 200) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.60.1:1812 activated on WLAN 1
RADIUS server 192.168.50.1:1812 deactivated on WLAN 1
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 15) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 16) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
RADIUS server 192.168.60.1:1812 deactivated on WLAN 1
RADIUS server 192.168.60.1:1812 failed to respond to request (ID 200) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.60.1:1812 activated on WLAN 1
RADIUS server 192.168.50.1:1812 deactivated on WLAN 1
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 15) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
Need to know how can i troubleshoot this further?
Regards
MaheshI would do the troubleshooting in following sequence.
1. Put a wired PC on to the vlan allocated for WLAN1
2. Check whether wired PC gets an IP & can browse internet
3. If that works, then we know no issue of DHCP & not issue with L3/NAT routing to access internet
4. If step2, does not work then your issue is not within wireless, you have to change the focus of your troubleshoot.
5. If step2 works, then test a wireless client with OPEN Authentication (No ACS involvment).If this does not work,then it means wireless client does not get proper IP connectivity. Check dynamic interface configuration for this WLAN & make sure gateway addresses correctly configured. Also VLANs are trunk across to WLC from switch.
6. If step5 works, then try your client with ACS & see the client get successfully authenticated. If not it may be WLC to ACS issue. Troubleshoot that in that case.
Do some troubleshooting like this & let us know the outcome. I am sure you will abe to find out the issue easily in this way.
HTH
Rasika -
Since installing the lastest soft wear I have been unable to log into internet banking for nab on the app and via safari? Anyone have an idea why?m
I experience similar problem with working in internet. Also use Safari.
-
when im accessing the internet using my iphone i cant use it because i am having a grey screen and the phone disables itself. how can i fix it. thanks.
You must have a valid form of payment for the app store in the country you are using. Most app stores are separate legal entities to comply with local laws. It is possible to have an account without a credit card, however; see: http://support.apple.com/kb/HT2534
-
Can you access the internet using wifi only on an iPhone 4?
How can you access the internet using WiFi only (no service) on an iPhone 4?
Assuming your connected to wifi - go to safari.
-
unable to log into iMatch using Apple Id and password. Msg says i have valid Id for store but not iMatch. What to do?
Is there a way to reset iMatch username and password?An Apple ID which consists of a non-Apple address can perfectly well be used to create and sign into an iCloud account (most Apple ID's take this form). Your problem is that you can't create an iCloud account on Windows: you can only do it on a Mac or an iOS device. Once created on one of those you can sign into it on Windows using the iCloud Control Panel.
-
I can't access the internet using Firefox. My internet connection is working perfectly fine as I can access the internet using internet explorer. I don't feel safe using internet explorer and prefer Firefox. Please help!
See --> [https://support.mozilla.com/en-US/kb/Cannot%20connect%20after%20upgrading%20Firefox Cannot connect after upgrading Firefox]
Your firewall may not recognize the new version of Firefox; it is just doing its job. You may need to remove references to Firefox from your firewall's allowed applications list, then try to go to any website, let your firewall detect the new version of Firefox, and give Firefox the permissions needed by your firewall to access the internet.
'''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.''' -
IPad & iPhone 4s unable to access internet on wi-fi
My iPad and iPhone 4s (both on iOS 6.0.1) don't seem to be able to access the internet on my home wifi network (WPA). My iPod Touch (also iOS 6.0.1) works just fine with the network. This is the first time it's happened, I've reset network settings multiple times on both devices to no avail.
They both connect and access fine on other wifi networks.
They automatically sign into the home network as usual but browsers and apps always time out. What's even stranger is that on my iPhone I do get pop-up notifications (from Twitter and Facebook) when the phone is on standby but once I open the notifications the request times out :-(
No other Apple device or in the household is having an issue with the home wifi network.Turn off "Smart Set Up" on the homehub. It can cause problems on mobile devices.
http://bt.custhelp.com/app/answers/detail/a_id/44328/~/switching-smart-setup-on-and-off-on-the-bt-ho... -
HT4623 iphone 5 unable to connect to internet
iphne 5 unable to connect to internet
I had the same issue and usually a reset of all the network settings on iphone did the trick.
this method did not work with my iphone 5 . i did something in router settings that seemed to change things a lot, for the better.
the wifi channel usually the routers use is channel 11, so i changed mine to channel 1. this solved my issues and the iphone connected just fine to the network, without restarting the iphone or resetting any settings or switching off and back on the wifi.
i am on 6.1.3 iOS -
HT4623 ios 6 unable to access 3g internet?
I recently updated to ios 6 (iphone 4s). Since the update I have not been able to access the internet (Telstra 3G) unless I have a wireless connection What can I do to fix this?
Can you dial *228, option 1 to reprogram your phone to the Verizon network?
The other thing I wonder is if the phone was activated properly in Itunes. -
Help! I have an older iPad. I am not sure which version. I cannot access the internet even though it shows a strong Wi-Fi signal. I have tried re-starting and when I tried to search for updates I couldn't access. It told me an error had occured. What can I do? Thanks!
Me too having the same thing what's the solution for this how can I update
Maybe you are looking for
-
Cannot see "New Entries" in transaction BD54
Hi all, I am working on an IDOC to File scenario.I am doing the ALE settings. However when i try to create a Logical system using transaction BD54; it says " Display View 'logical Systems':Overview" also i cannot see button for New Entries. kindly s
-
Satellite Pro - Slow start up and sound is messed up
I have had my *Toshiba Satellite Pro* with *Windows XP* for a good few years now. She has always worked like a gem and has given me no problems until a few weeks ago. A few weeks ago I was downloading a program and with it came the very unwanted and
-
GL code for common company code
Hi Please suggest the solution in following situation:- Situation:- we have 10 company code with common chart of account. first we have created one company code (say 1000) and rest we have created with reference to first company code (say 1000). thru
-
Reading in a certain number of characters from a file.
Hi guys, I need some pointers on how to read in a specified number of characters from a text file.For example,how would I read in the first 100 characters to an array from a text file with an unspecfied number of characters (more than 100 rather than
-
Launching URL without Address bar and Menu Bar
Guys, I use the following piece of code to launch an URL from the application. I want to launch the URL without address bar & Menu bar. how this could be achieved? <af:goLink id="gl1" targetFrame="_blank" destination="/faces/com/abc/xyz/pages/page2.j