HT204032 Late 2011 MacBook Pro Power Nap

I have a late 2011 MacBook Pro with a SSD from factory. Is there a way for me to have the power nap feature? I have tried the new firmware for the retina MBP but will not work. Theoretically there is no reason it can't work on the device I have 8gb RAM and a 256GB Solid State Drive.

Power Nap requires a Mac notebook with built-in flash storage. May require a firmware update.

Similar Messages

No Power Nap option Late 2011 MacBook Pro

Here is what the specs for Power Nap say:
Power Nap
Supports MacBook Air (Mid 2011 or newer), MacBook Pro with Retina display.
Does that mean that Power Nap is not supported with my Late 2011 MacBook Pro?

reveusetoujours wrote:
I was reading that it is because one of the requirements is flash storage, , so I don't think it will be coming in an update. I have a Feb 12 MBP and probaly won't get the upgrade either.
I had read that too. Fortunately, I meet that requirement. I have one of those expensive Apple SSD's. So that was not my problem. Sadly, I just don't have the right hardware for this feature.

Late 2011 Macbook Pro Restarts When Power Connected

I have a late 2011 Macbook Pro, 2.2 GHz with 8GB Ram with OS X 10.8.2 and a series of unfortunate events.
When I connect the magsafe adapter to the computer, after it has been shut down completely overnight, with the lid closed, the Macbook attempts to restart. The restart fails beause the lid is closed but leaves my Macbook in an unstable state. Unless I do a PRAM reset whenever this happens, I will have at least one random shutdown, usually within the first half hour of use after the computer restarts itself. I have also reset the SMC controller, checked the hard drive for errors and tested the memory. I have been careful to make sure that the computer shuts all of the way down before closing the lid and disconnecting power. As far as I can tell at this point, starting the computer on battery, and subsequently connecting the magsafe adapter, does not cause any problems.
I never saw this behavior until I installed Mountain Lion.

Run an Apple hardware test and see if that picks up any problems. If this phenomenon is consistently repeatable, I recommend taking it to a repair facility for a diagnosis. This clearly is not normal operation. I hope that you might be still in the warrantee period.
Ciao.

Late 2011 MacBook Pro stuck at spinning wheel of death after a Thunderbolt issue, HD erasing and fresh Lion install from Recovery HD. Please help me!!!

So, I think the title says it all, but to give you a little more info:
I connected my late 2011 MacBook Pro to my TV using a Thunderbolt HDMI adapter, and closed the lid. When I opened it, it wouldn't show the login screen, so I restarted using power button. Got stuck at the Apple logo with the spinning wheel. So I booted the Recovery HD and found out it was a HD problem, so I (reluctantly) erased the HD and installed Lion from scratch. When it rebooted (after DOWNLOADING the Lion components) I got some terminal commands (sorry for not being more specific, still a noob when it comes to Mac) and then the screen faded and a message appeared saying I needed to reboot the computer. So I did. 3 effing times. Then I got stuck AGAIN at the spinning wheel, and I'm currently with that on my screen. I'm trying the forums before calling Apple (my computer's still within the 90 days of warranty) because it's not yet 9 A.M. where I live

can you go back to recovery mode then open disk utility.
in disk utility, higlight the disk, the one saying the brand and size then click on repair disk under first aid tab
if it repairs fine, that's okay
if repair was not successful, go to partition and change current to 1 partition then apply
install lion again
hope this helps

Late 2011 Macbook Pro with SSD Freezing

Hello,
I have a late 2011 macbook pro and about six or so months ago I have it a new lease on live with a Samsung 840 SSD (non pro).
I haven't really had any problems with that until recently - the machine started locking up on wakeup. This meant that the beachball of doom would start and each program would gradually in turn become unresponsive. Shutdown command wouldn't work and would time out, force quit wouldn't open, and although I could move the mouse around and sometimes switch between programs, they didn't work and the only cure was to hold the power button until it switched off.
This has also started happening just when the computer has been on for a certain amount of time *without sleeping*. For example, if I watch an episode of a tv show, by the end of it the video is still running but all of the other programs are locked up - clicking out of VLC causes the beachball of doom. This also happens in other programs - it's even happened as I've been writing this, and the only remedy seems to be a hard restart.
The problem doesn't seem to occur in windows. In OSX I have 'put hard drives to sleep' turned off, and TRIM enabled. I also disables the sudden movement sensor. I have also reset the SMC.
Does anyone know of a remedy short of a full reinstall of Mountain Lion?
Oh and I used samsung magician in windows to update the firmware of the drive. It reports that the drive should be fine.
Thanks very much for any help anyone can give me with this!

anything is possible - corrupt files - corrupt drivers - it could be anything.
try doing a nvram/pram reset and see if that sorts it out.
i have ssd installed in all my Macbook/Macbook Pro and have never had any issues.
Then again, I don't have windows installed in any of them.
hopefully the nvram/pram reset sorts it out for you.
once you've done that reset - go back to system preferences - startup disk and select your ssd as the startup drive again - then restart it again.

Late 2011 MacBook Pro (Mountain Lion 10.8.2) backlight keyboard not functioning properly?

I have a late 2011 MacBook Pro running OS X Mountain Lion 10.8.2 and for some reason, the automatic backlight keyboard will not funtion as it should. When I have the "Adjust keyboard brightness in low light" option enabled in settings, and I turn on the lights, my backlight keyboard stays at full brightness. Then, when I turn off the keyboard, then the lights, the keyboard does not turn on! Correct me if I'm wrong, but I am pretty sure that this was a feature in the MBP lines.

Try a SMC reset. Shut down the computer. Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected. On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time. Release all the keys and the power button at the same time. Press the power button to turn on the computer. Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.

13-inch, Late 2011 Macbook Pro and Thunderbold Display...

Hello Dear Users,
First I wish you have a nice new year with full of health, happiness and wealth, then i am asking my question:
I am using a 13-inch, Late 2011 MacBook Pro having
Processor 2,8 GHz Intel Core i7 2 cores+2 HTs
Memory 16 GB 1333 MHz DDR3
Graphics Intel HD Graphics 3000 512 MB
Software OS X 10.9.1 (13B42)
specifications, setup with double Thunderbold Displays.
I sometimes feel that mac's display performance is marvelous and sometimes I feel like I am looking at an old school, blury screen. Is there anybody feels like I feel. I have doubts about screen performance. Well I searched on internet before to write but I could not express what I feel on google search for example. So, I am writing here what I feel. Sorry for my English if I could not express what I meant.
Thak you, and have a nice new year.....
Levent

I've been having the exact same issue, same monitor and same laptop. I spoke to a couple Apple techs on the phone and took my mbp to a genius bar last night, thinking it might be a video card issue since the blocks were also showing up on my macbook's screen. It of course failed to replicate at the store, even with a TB display hooked up.
After this I finally realized it was an issue with the monitor and not the laptop, since it only happened when they were connected (duh... I never checked with them disconnected)
I was able to make it go away temporarily by pushing the cables on the back of the display firmly in, but a few hours later I noticed a couple blocks popping up again.. however it wasn't as bad as before. Seems to me it must be some issue with the hardwired power/tb connetor.

Late 2011 Macbook Pro green pixels on the screen where dark colors should appear.

I have a late 2011 Macbook Pro I bought it new with 4 gb of ram. About 4 months ago i purchased 8 gb of pny ram for this model and upgraded the ram. I followed all of the safety precautions and discharged my static electricity before upgrading. It increased the speed of my mac and helps with certain tasks. About 2-3 weeks i notices my mac froze and strange green black and pink bars appeared on the screen so i hold the power button to shut it down and it solves the problem this will happen about once a month but otherwise my mac works perfect. Now about a month ago I powered my mac on and low and behold The screen was covered in green pixels. I tried rebooting twice and it didn't do anything then i let it sleep for about 5 mins opened my mac and the green pixels were gone. Now my mac is still usable and everything works its just sometimes like once in a while ill get a few pixels and closing and opening my mac fixes it. I was curious if this was related to one another or is my mac just starting to die....

I have been getting green pixels/boxes the last while...
I have noticed it after waking the machine from sleep. Not 100% sure if that is the only time it happens. It goes away after a few seconds, typically.
Any idea what is going on?

Late 2011 macbook pro will not perform AHT

Hi All -
I have a late 2011 Macbook pro (A1278) running 10.6.8.
I've tried running AHT by holding D down while powering up as well as trying D+Option. Neither method is working. I've been sure to hold these buttons down before pressing the power key and continued to hold them down but nothing happens. The computer just boots up as normal. Suggestions?

Hi All -
I have a late 2011 Macbook pro (A1278) running 10.6.8.
I've tried running AHT by holding D down while powering up as well as trying D+Option. Neither method is working. I've been sure to hold these buttons down before pressing the power key and continued to hold them down but nothing happens. The computer just boots up as normal. Suggestions?

Late 2011 Macbook Pro won't sleep!

So I purchased a late 2011 macbook pro brand new from an apple store 3 weeks ago. Everything seemed well at first (except for a wake issue I had... odd)
Anyways... I started noticing that my notebook wasnt going to sleep, so I adjusted the power settings to sleep after 1 minute...
Sometimes the laptop will sleep after 20 minutes or more... sometimes it won't sleep at all (on all night!)
I'm wondering what the heck is going on? I tried re-installing Lion and using migration assistant to bring all my files back... no dice. same symptom.
-I've re-installed Lion
-I've tried SMC and PRAM resets
-I've tried "pmset -g assertions" and see no conflicts
-I've tried "pmset -g" and see nothing odd
-I've tried clicking / unclicking all the "sharing" settings
-I've made sure ALL applications are closed
-pmset -g log returns a few "slowresponses" but nothing too crazy (200ms)
-system log returns some odd "wake for GIGE (network)" responses while im trying to make it sleep.
-I deleted all printers /ques
The system WILL sleep if i manually click "sleep" or use the power button.
The system WILL sleep if i unplug the power cable and close the lid.
I have a 2nd display using a thunderbolt to DVI adapter... but unplugging this seems to have no effect.
What am I missing? could this be a logic board issue on a brand new mac? I'm lost! any suggestsion would help!

I may have solved this -- maybe -- by reinstalling Mavericks. Two days after the re-install (which was easy), the sleep function seems to be working properly.

What external drives work well with a late 2011 MacBook Pro? I ask because I just found out the hard way that a Samsung EVO 840 does not. Also should I avail myself of something that works with Thunderbolt or Firewire?

What external drives work well with a late 2011 MacBook Pro (I7, Lion OS) apart from my Kingston flash and USB drive, and the SD drives that I use in my cameras and recording devices? I ask because I just found out the hard way that a Samsung EVO 840 does not. Also, should I avail myself of something that works with the Thunderbolt or Firewire connections? I'm looking to back up music and video files created and/or processed in Logic Pro and the Adobe Production Premium software suite (Premier Pro, After Effects, Audition, etc).

Hmm, not sure what problems you had installing this drive. The review here gives it good marks for Mac:
http://www.amazon.com/Samsung-Electronics-EVO-Series-2-5-Inch-MZ-7TE1T0BW/produc t-reviews/B00E3W16OU
There does seem to be a lot of prep to make it work:
"1. Preparation to install your new shiny SSD
1.a You will need a migration tool (I used the Sabrent kit USB 3.0 to Sata that was suggested in these review) see link http://www.amazon.com/gp/product/B00DQJME7Y/ref=oh_details_o03_s01_i01?ie=UTF8&p sc=1
1.b You will need to download a trim enabler (mid 2012 macbooks only support native trim with apple brand ssd's) I recommend going to cindori.org and downloading trim enabler version 3.xx. You can do this step before or after the OS migration
1.c You cannot use the Samsung SSD migration software *don't worry Mac has its own imaging/migration utility*"
Also in those reviews:
" Only down side when using this product in a Mac Mini is you will be required to download and install Trim Enabler so that your drive performs optimally on your Mac device. This is an Apple issue, not Samsung, but it is an extra step you will have to take after you install the hard drive, and any time you perform an OS upgrade." He rant's on.
Personally I only deal with OWC:
http://eshop.macsales.com/shop/SSD/OWC/
They are very knowledgable and if there's a problem they will gladly take back the item. (Never happened to me yet - 8 years and counting).
Just upgraded my 13" MBP 2011 to 120 GB for $79. Adobe CS 6 opens in 3 seconds! Awesome!
When I was in Chicago I had a pro photographer for a client. She wound up with 4 internal drives in her Pro, 4 external drives and an dual array locked in a steel vault in the basement. All from OWC. OK she was a bit paranoid. Great client though.
As far as value for price:
http://eshop.macsales.com/item/OWC/MES3FH7500G/
500 GB for $130.
However as far as reliability is concerned:
http://www.rockpapershotgun.com/2014/01/30/are-ssds-reliable/
http://www.extremetech.com/computing/173887-ssd-stress-testing-finds-intel-might -be-the-only-reliable-drive-manufacturer
So sudden power loss is an issue with SSDs.
Personally I'd go with a moderate sized SSD internally and a conventional external for backup. An array would be the most reliable.

HT201295 Late 2011 Macbook Pro refuses to boot. SMC reset doesn't work

Late 2011 Macbook Pro refuses to boot. SMC reset does nothing. Have tried bypassing SMC (nothing).
Magsafe light glows very very faintly (barely visible in a room with lights on).
Have tried reseating the battery connector. Battery indicator status button illuminates no LEDS (despite it being charged before failing).
The mac didn't get wet. Was using a non apple USB cable at the time to tether/charge iphone. Computer just dead after working fine.
Any ideas anyone. Logic board?
Many thanks and best wishes
Jamie

Is it a 15" or 17" MBP? There have been logic board issues with that model.
https://www.ifixit.com/Device/MacBook_Pro
For all models.
If it's a 13" take the bottom off and disconnect the battery:
https://www.ifixit.com/Guide/MacBook+Pro+13-Inch+Unibody+Late+2011+Battery+Repla cement/7649
So only do this through step #3!
Wait 10 seconds. Push the power button for 5 seconds. Wait 10 seconds. Reconnect the battery. Put the bottom back on don't screw it on just yet. Tape it temporarily in place and try to start it
Even if it's a 15" or 17" try this anyway. Usually when graphics on the logic board fails there will have been anomalies beforehand.

Hi i cannot change the brightness on my late 2011 macbook pro.

Hi i cannot change the brightness on my late 2011 macbook pro. It is stuck on the lowest level in which i can't view the screen without a flash light. Please i need help how to solve this. I was on my computer when i checked the back which it was really dusty, i tried unscrewing the bottom however some screws were too tight so i took it upon myself and got a rod and startedremoving the dust off the vents and i may have clicked something as i closed the lid on the macbook i could hear the sounds still from the film but the lid was closed as i opened it back up the brightness was on low but sounds were still playing. All the buttons work , all of the F keys, apart from the brightnes keys. I can shine a tourch on the screen and see the display but the brightness will not change but i can see when i click the brightness it says it changes. I have connected it to a spare tv i have via hdmi and i really need help as this is my primary computer and i need it for work when going away. Thank you

Try SMC and PRAM resets:
http://support.apple.com/kb/ht3964
http://support.apple.com/kb/ht1379
Ciao.

Having problems connecting a late 2011 Macbook Pro 2.2ghz i7 to a Sony KDL-32L5000 using a display miniport to DVI adapter (DVI to VGA cord). The TV is not detecting the macbook. Anyone have this problem?

Having problems connecting a late 2011 Macbook Pro 2.2ghz i7 to a Sony KDL-32L5000 using a display miniport to DVI adapter (DVI to VGA cord). The TV is not detecting the macbook. Anyone have this problem?

You really have to mess with the resoluton, espescially the refresh rate, as it varies from projector to projector, monitor to monitor. Even within the same brand! Because so many manufacturers are trying so many different things to become the next cool kid on the block, and the way the formats are being configured that's now part of the game.
That's why so many professionally produced corporate shows hire a dedicated projectionist for the video presentations. Too many bugs in the honey.
Refresh & sesolution are the first things to look at.
Just so you know that colors in PowerPoint PC, and PowerPoint Mac, don't exactly match... go figure.
I forgot to mention another thing, sometimes it's the projector that needs to be tweaked.

What cable do I need to move files from my macbook pro 1,1 (2006) to my new (late 2011) macbook pro?

I am trying to migrate everything from my macbook pro 1,1 (2006) to my new (late 2011) macbook pro?, what cable do I need? I have now bought the wrong one twice...!
Thank you!
Alice

Firewire 400 to 800
Best.

HT204032 Late 2011 MacBook Pro Power Nap

Similar Messages

Maybe you are looking for