HT204088 Billing problem need help

Order number MHBGWDGXZ6 is false charges, How do i clear them and block king.com??

These are user-to-user forums, you can contact iTunes support here : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption

Similar Messages

Zen Vision:M problem, NEED HELP!

My zen vision:m is starting to run slowly. It started right after my player froze and i reset it.Now its really slow and barely even switches screens sometimes.Right now its just a black screen with the keypad lit up.Whats wrong with it'sI NEED HELP!

johnnnyp wrote:
hi, i have a problem with my creative vision m. i wanted to watch a movie and it froze. i tried to shut it down but it wouldnt respond, and now is frozen. please help me if you can!
You know its kinda rude to derail XBenzinoFla thread with your own problems, make your own thread next time.
But to the both of you especially XBenzinoFla, try putting your ZVM in rescue mode and run scan disk to see if it hel
ps.

Zen Micro problem need help

Today i was listening to music and my zen micro just froze while playing and no buttons could be pressed and the lock button wasnt on. So i took the battery out and rebooted the player but it froze at the creative screen. I went home and i went to recovery mode and tried to reload the firmware but it said erasing firmware for more than 2 hours. So then i tried a format but it said formating for the same amount of time. I need help please. Also, recently i've had problems witht the headphone jack. When ever i would stick it in it would sound distorted and i would have to move it around until i got it to a certain spot to hear it good again. If anyone else has this problem please tell me. One more thing i had returned my other micro zen in for hard dri've probems and this was my new one do u think if i have to return in (hopefully not) that they would accept it.

If the functions in Rescue Mode aren't working properly then you need to contact Creative Support.

I have a billing problem ,please help i can not download anything

i have a billing problem i can not download anything and this frustrates me i phone uses please help me before i throw away this i phone.

Contact itunes at expresslane.apple.com or reportaproblem.apple.com.
But Itunes can not refund until the balance is paid.
purchase a gift card redeem it in the store if you want refund for the charges contact itunes.

Still stuck with the same old producer consumer weight problem need help

Hello All,
This is the problem I am stuck with right now.
I have two array lists one producer array list and one consumer array list denoted by a and b
P1 P2 P3 P4 P5
5 6 7 8 9
C1 C2 C3 C4 C5
2 3 4 5 6
Now we find all those producer consumer pairs which satisfy the criteria Pi>=Ci
We have the following sets
(5,2)(6,2)(7,2),(8,2),(9,2)
(5,3)(6,3)(7,3),(8,3),(9,3)
(5,4)(6,4)(7,4),(8,4),(9,4)
(5,5)(6,5)(7,5),(8,5),(9,5)
(6,6)(7,6)(8,6),(9,6)
Let us done each of them with Si
so we have S1,S2,S3,S4,S5
we assign a third parameter called weight to each element in Si which has satisfied the condition Pi>=Ci;
so we we will have
(5,2,ai),(6,2,bi),(7,2,ci)....etc for S1
similarly for S2 and so on.
We need to find in each set Si the the pair which has the smallest weight.
if we have (5,2,3) and (6,2,4) then 5,2,3 should be chosen.We should make sure that there is only one pair in every set which is finally chosen on the basis of weight.
Suppose we get a pair (5,2,3) in S1 and (5,2,3) in S2 we should see that (5,2,3) is not used to compare to compare with any other elements in the same set S2,
Finally we should arrive at the best element pair in each set.They should be non repeating in other sets.
Given a problem
P0 P1 P2 P3 P4
9 5 2 2 8
6 5 4 5 3
C0 C1 C2 C3 C4
we have So as (P0,C0) and (P4,C0)
assuming that the one with the smaller index has lesser weight PO is selected.In the program I have used random weights.from set S1 we select the pair PO,CO
S1 =(P0,C1),(P1,C1) and (P4,C1)
since P0 and P4 are already used in previous set we dont use them for checking in S1 so we have (P1,C1) as best.
S2=(P0,C2),(P1,C2) and (P4,C2) so we dont use P0,C2 and P1 and C2 because PO and P1 are already used in S1.
So we choose P4,C2
in S3 and S4 ae have (P0,C3),(P1,C3),(P4,C3) so we dont choose anything
and same in S4 also.
So answer is
(P0,C0),(P1,C1) and (P4,C2).
My program is trying to assign weights and I am trying to print the weights along with the sets.It doesnt work fine.I need help to write this program to do this.
Thanks.
Regards.
NP
What I have tried till now.
I have one more question could you help me with this.
I have an array list of this form.
package mypackage1;
import java.util.*;
public class DD
private int P;
private int C;
private int weight;
public void set_p(int P1)
P=P1;
public void set_c(int C1)
C=C1;
public void set_weight(int W1)
weight=W1;
public int get_p()
return P;
public int get_c()
return C;
public int get_x()
return weight;
public static void main(String args[])
ArrayList a=new ArrayList();
ArrayList min_weights_int=new ArrayList();
ArrayList rows=new ArrayList();
ArrayList temp=new ArrayList();
Hashtable h=new Hashtable();
String v;
int o=0;
DD[] d=new DD[5];
for(int i=0;i<4;i++)
d=new DD();
for(int i=0;i<4;i++)
d[i].set_p(((int)(StrictMath.random()*10 + 1)));
d[i].set_c((int)(StrictMath.random()*10 + 1));
d[i].set_weight(0);
System.out.println("Producers");
for(int i=0;i<4;i++)
System.out.println(d[i].get_p());
System.out.println("Consumers");
for(int i=0;i<4;i++)
System.out.println(d[i].get_c());
System.out.println("Weights");
for(int i=0;i<4;i++)
System.out.println(d[i].get_x());
for(int i=0;i<4;i++ )
int bi =d[i].get_c();
ArrayList row=new ArrayList();
for(int j=0;j<4;j++)
if( d[j].get_p() >=bi)
d[j].set_weight((int)(StrictMath.random()*10 + 1));
row.add("(" + bi + "," + d[j].get_p() + "," +d[j].get_x() + ")");
else
d[j].set_weight(0);
row.add("null");
rows.add(row);
System.out.println(rows);
int f=0;
for(Iterator p=rows.iterator();p.hasNext();)
temp=(ArrayList)p.next();
String S="S" +f;
h.put(S,temp);
String tt=new String();
for(int j=0;j<4;j++)
if(temp.get(j).toString() !="null")
// System.out.println("In if loop");
//System.out.println(temp.get(j).toString());
String l=temp.get(j).toString();
System.out.println(l);
//System.out.println("Comma matches" + l.lastIndexOf(","));
//System.out.println(min_weights);
f++;
for(Enumeration e=h.keys();e.hasMoreElements();)
//System.out.println("I am here");
int ii=0;
int smallest=0;
String key=(String)e.nextElement();
System.out.println("key=" + key);
temp=(ArrayList)h.get(key);
System.out.println("Array List" + temp);
for( int j=0;j<4;j++)
String l=(temp.get(j).toString());
if(l!="null")
System.out.println("l=" +l);
[\code]

In your example you selected the pair with the greatest
distance from the first set, and the pair with the least
distance from the second. I don't see how the distance
function was used.
Also it's not clear to me that there is always a solution,
and, if there is, whether consistently choosing the
furthest or the closest pairs will always work.
The most obvious approach is to systematically try
all possibilities until the answer is reached, or there
are no possibilities left. This means backtracking whenever
a point is reached where you cannot continue. In this case
backtrack one step and try another possibility at this
step. After all possible choices of the previous step,
backtrack one more step and so on.
This seems rather involved, and it probably is.
Interestingly, if you know Prolog, it is ridiculously
easy because Prolog does all the backtracking for you.
In Java, you can implement the algorithm in much the same
way as Prolog implementations do it--keep a list of all the
choice points and work through them until success or there
are none left.
If you do know Prolog, you could generate lots of random
problems and see if there is always a solution.

Ipod problem NEED HELP ASAP

Hello guys,my ipod touch has battery problems and internal speaker are not working and will apple replace me a new one,i even have 1 year warranty and i want a new ipod touch white instead of black<<<plz plz plz reply ASAP plz really need HELP!THANK YOU

If you iPod is defective, in warranty and not abused Apple will replace it with a refurbished one. They may or may not replace it with the white one. You will have to ask.
Other users have asked the same question but I hav never heard them come back with whether or not they go the color changed.

Another Infinite Login Loop Problem - need help badly

Hello. I need help.
When I start up my iMac (24 inch last generation model) I can't log into the OS. When I enter my password I see the default OS wallpaper (nothing else) then it kicks me to a blue screen then right back to the login. Same thing over and over. I've already ran disk utility off of the install CD to repair permissions, etc... but no luck. This even happens when I enter into safe mode. I'm running the latest version of the OS.
Can anyone help me?

Restore the bootable backup/clone or Time Machine backup. Without one, you have a difficult situation. First thing to try is boot with your install disc, run Disk Utility, and repair the disk.

Ipod nano Problems need help fast!!!!!!

I got my nano in october everything was working fine.Until 2 weeks ago my ipod wasnt getting reconized by itunes.Im really getting frustrated and i need help.

Welcome to Apple Discussions!
Read through this...
http://docs.info.apple.com/article.html?artnum=61711
btabz

Billing problem. Help!!

I had a billing problem on iTunes about 3 months ago and I now can't download anything from the App Store, even free apps because it mentions this billing problem and keeps rejecting my payment method. What do I do?? I don't have any other way of paying

Contact iTunes Customer Service and request assistance...
They are the ONLY ones who can assist you.
Use this Link > Apple Support iTunes Store Contact

Urgent Problem, need help asap.

Hello everyone,
I'm sorry for the alarmist title, but I need help and I need it badly. Just last night, my macbook froze with nothing working. The mouse froze, the interrupt keys didn't work, nothing. I shut down the laptop, and tried to restart. I noticed a clicking sound coming from the lower left hand corner of the macbook. I'm assuming this is the hard drive.
What happens is that there will be two clicks happening in a rythmic fashion, and after 15 second of booting up, a folder will appear with a question mark on the screen. The only thing I can do is power it down. Can someone please describe what is happening and make suggestions?
The kicker is that I'm a college student studying in Denmark for the semester. The laptop is my only lifeline to back home. Please, any help is greatly appreciated.
Matt

You may have a disk failure or simply corrupted files. If you have a bootable backup that is working, then you can boot from it, erase your hard drive, then restore your backup. If not then do this:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If the drive is OK then you can reinstall OS X:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger) and/or TechTool Pro (4.5.2 for Tiger) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

G5 DVI to VGA Dell Monitor Connection problems, need help!!!!!!!!!!!!!!!!!!

hello,
I'm running two dell monitors both of which were connected via DVI to my g5 quad dual dvi. My tv broke and I'm using one of my monitors to connect the cable boxes HDMI input to the dells DVI input, it works great.
My problem is that i still want to run two monitors from my mac and still be able to switch channel sources from the Dells source button allowing me to switch from TV to Mac. Since I took up the dvi port on one of my monitors to connect to the cable box via HDMI, I have a free DVI cable. I purchased a tiny converter that allowed to change one end of the free DVI cable to VGA. I used this method to connect the cable to my g5's dvi port and the configured end to the VGA port on the monitor with no luck.
The Dell monitor does not pick up any signal and just goes to sleep as if my computer does not exist. The TV works fine and I'm able to switch sources. Please note that I'm not using the DVI-VGA adaptor that came with my g5 and don't know if this would make a difference. If it does, how do i set this up because this adaptor is like 5 inches long.
Does the adaptors DVI end need to be connected to the back of the g5 or does the VGA end need to be connected to the monitor or does it not matter. I need a longer dvi-vga cable as well, do they make them. This all depends if the problem actually is that that I'm not using the DVI-VGA cable that came with my mac to connect to the monitor in the first place.
Can anyone help me out here. I'm using the Dell 2208WFP Ultra Sharp.

Bad adapter?
The G5 ports are DVI-I. Any good DVI-I to VGA adapter should be fine.

Setup Problem - Need Help Please!!

My problem is a low hum eminating from my speakers every time I connect my MPC2000 sampler to my audio interface.
My setup consists of the MPC2000, a Dj Mixer, and my laptop which has an M-Audio interface which I use to connect the mixer & MPC. Basically, as soon as I remove the cables that connect my MPC or my mixer to my interface, the hum stops. I've tried different cables, new cables, a ground adapter for the MPC to change it to 2 prong, and nothing helps. The only thing that DOESN'T cause this hum when plugged into my interface, is my keyboard, so i'm quite sure the interface itself isn't the problem.
Does anyone know what might be causing this interference that's resulting in a hum? I have exhausted all my own theories and am desperate for some sort of help! Many thanks in advance!!!

Hi beirut,
Try the following:
1.Put the mpc2000,the dj mixer and your computer all in the same power outlet from the wall.
2.Go to home despot and buy a few gray-colored ground lift plugs (they must be gray)
3.With these gray ground lift plugs,lift the MPC2000.test the system.No hum=solved problem.hum still there or different,list the DJ mixer.
4.Is your DJ mixer hooked up to turntables? If so,you need to ground the turntables to a proper ground.Good turntables have a little wire coming out of them,just for that purpose.
5.Try turning off any TVs,refridgerators,fluorescent lighting(the ones that look like office lights),and other things around your place,and see if the hum goes away.
6.Try using a DI box for your DJ mixer,to plug it in to the DI,and then out to the audio interface.
7.And Most Importantly... RUN AND BUY A DIFFERENT BRAND OF AUDIO INTERFACE!!!!!!!!!! M-Audio...yucky yucky yucky!!!
Cheers

Serius project problems - Need help please

Hi,
I'm using adobe premiere and after effects to my last film (this is not the first time). I'm using DV 1280*720 default sound settings (as I did before in other movies). I have an Imac C2D and plenty of hard disk space.
Yesterday when I import new takes and done some light fx's (blur 10% and tint) when I saved the premiere frozen for 30 minutes and then I had to force quit.
When I've tried to open that project again, it just don't open. I've tried everything. See if there was any corrupted file, checked for Hard drive problem (it doesn't have any) and I delete the previous rendered files (as I saw on some tutorial).
At least I could recover that project using autosaved and previous project backup (I take care always of saving backups).
But when I saved again (the new recovered and rendered project) it freezes on quit and there comes again. (it seems that premiere it is getting something from the old(damaged) project and just stack there !!!!!!
The project then it just don't open (I don't see any error message) I just see after 1 hour my premiere freezed and there is no way to see the timeline to fix anything.
I assume that I have to recover again and to all work over and over. I saw some forums talking about adobe "broken links" something related to video files source and corrupted files, but I still don't get it (since premiere doesn't tells me what is going wrong!!!!!!). They talk about deleting MACC file on windows but I'm on a mac. I didn't saw any tutorial about recovering.
whe this thing happens I see my timeline with video and audio. I can render but when I quit the program doesn't load the project again.
Please any help...... I'm working since a month ago on this movie and I need to deleiver that asap.
Is it better to export the video in parts and them join in a new project or there is any other thing that I can do without missing my month of work.
ohhh man I just want to scream

For any reason that I can't explain when I arrived home after day work, I've tried last time before looking my backups and Premiere loaded my project
Before save and quit I've take a look in all file (check the link and where is the source) I found 2 still frames (photos) were lost ( i mean from my hard drive).
My biggest clue now it is, when I deleted some video file before, when I enter the premiere project 1st thing that show it is a windows asking me to "point" where is that file.
But when happens with a photo, premiere doesn't say that this files are lost. It just stucks your project. Any tip to prevent this again?
Hardware Overview:
Model Name:    iMac
Model Identifier:    iMac7,1
Processor Name:    Intel Core 2 Duo
Processor Speed:    2.4 GHz
Number Of Processors:    1
Total Number Of Cores:    2
L2 Cache:    4 MB
Memory:    4 GB
Bus Speed:    800 MHz
Intel ICH8-M AHCI:
Vendor:    Intel
Product:    ICH8-M AHCI
Speed:    3 Gigabit
Description:    AHCI Version 1.10 Supported
WDC WD3200AAJS-40VWA1:
Capacity:    298.09 GB
Model:    WDC WD3200AAJS-40VWA1
Revision:    58.01D02
Native Command Queuing:    Yes
Queue Depth:    32
Removable Media:    No
Detachable Drive:    No
BSD Name:    disk0
Mac OS 9 Drivers:    No
Partition Map Type:    GPT (GUID Partition Table)
S.M.A.R.T. status:    Verified
Volumes:
iMac:
Capacity:    297.77 GB
Available:    158.68 GB
Writable:    Yes
File System:    Journaled HFS+
BSD Name:    disk0s2
Mount Point:    /
ps: about your question "Next, please verify your Project/Sequence Presets. Do they match your footage 100%?" I've changed 2 video files, they were pretty bigger than the part I was taking for this project, so I edit and save just the part that I am using.
Btw I've heard that Journaled HFS+ it is not good on Imac to use premiere render option. Is that right?
Many thanks in advance.

Flash Game Problem Need Help! Action-Script 2.0

Im making a flash game its a sniper game btw and i am have a problem with after killing the target for it to go to the next frame. I have tried on(press) on(release) for buttons i hae tried lots of different stuff (1.3 hours of trying) and so i was wondering if you could help me out. and here the link to the download for the source .fla yes i uploaded it cuz i really need the help ! thanks for any help! http://fileape.com/?act=download&t=yz6Lhp0oDdAB-7whXWB62WIoACXMVgV7r1flbKy17aJZamyC-vXNFwx tZP6pwXV50NGk3XWK9anDa4m6tBfGEtPOZwKbuZFcaFyGyEGiYqeILdcvVuEZy3QVHX3xY6S170xapkdrZJN9lov4k hxeqJ4_S6aGRpNQWjTT3MhudPLa1ZBAi79CiPqX5kN835lD7vzAU0O6WJZaK6jZBROg2A,,
or
http://fileape.com/dl/2gI8YiSW9QGzIgAu
if the top one doesnt work (the top one shouldnt have a time wait)
Thanks for all help
also please if you can find the problem itd be nice to know what it is

I will not download the .fla - maybe if you hosted the .swf I would view it.
to change frame use: gotoAndStop(<framenumber>);
(without the < >, just a number for the fram).
I recommend you use movieclips for buttons and place all code on the main timeline. For movieclips, give them an identifier name (bottom left int he properties box of the movieclip) then on the main timeline use:
movieclipName.onRelease = function(){
gotoAndStop(10);//change 10 to the frame you wish to go to. gotoAndPlay(10) plays from the frame.

Major iPod Problems, Need Help Solving

One day I was casually syncing my iPod video with my computer to get a few new songs uploaded onto it.
Suddenly, the iPod freezes up, shuts itself off, restarts, and magically it has forgotten everything and pretends it is a brand new iPod.
No problem, I think, believing it will just need to load the songs again and everything will be fine.
However, this is not the case.
The iPod would then continue to load all the songs, shut down after loading them, restart and again pretend it is brand new and lad all the songs again.
This continues to happen again and again.
I try to update my iPod, figuring it may just be a version error or somesuch nonsense. The updater refuses to work and actually causes my iPod to crash, saying it has a diskwrite error.
It refuses to "System Restore" on my computer, so I run the "System Restore" on another window computer that I own. And it runs just fine, making the iPod load songs once more.
And I think, problem solved!
However, again, this is not the case.
I load it once, everything goes fine.
The nxt day, after buying more songs, I try to upload and after the upload, the iPod shut off, restarts, and pretends to be new once more.
I go through the "System Restore" process again, but afterwards, the iPod all out refuses to upload my music fully, shutting off about halfway through the process each time.
And now whenever it is plugged into my computer, windows says it is unreadable and must be reformatted, so I run the updater and it says that there is an "iPod manager internal error" which could basically be another language considering my only basic knowledge of computers.
Is there any way to repair my iPod at home? Or must it be sent in to Apple?

GREAT NEWS!
Last night, through some very thorough digging in the
"Search Discussions", I found the answer and now my
iPod is running perfect once more!
Thank you very much for your help b noir. Without
you, and many others on this board who had their
problems solved by equally helpful people, I would
still be digging through Apple's support section to
no avail.
PS. I found the answer in http://discussions.apple.com/thread.jspa?message
ID=1539429

HT204088 Billing problem need help

Similar Messages

Maybe you are looking for