HT2188 Power button on iPhone not working

My power button is depressed and will not pop back up all the way, don't know why. I can use it if I press down really hard on it, very inconvenient.  Any  suggestions? 

Contact an Authorized Apple Service Provider.
Here's how:
Find an Apple Authorized Service Provider

Similar Messages

  • What to do now when my iPad won't turn on after I turn it off. It shows only the apple logo. I am sure it has above 70% charge as when I sync my iPad it shows necessary detail in iTunes. I have tried, HOME & POWER button, but did not work.

    What to do now when my iPad won't turn on after I turn it off. It shows only the apple logo. I am sure it has above 70% charge as when I sync my iPad it shows necessary detail in iTunes. I have tried, HOME & POWER button, but did not work.

    First try a Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least Ten seconds... (But can take Longer)... until the Apple logo appears. Release the Buttons
    If no joy... Try a Restore...
    1: Connect the device to Your computer and open iTunes.
    2: If the device appears in iTunes, select and click Restore on the Summary pane.
    Restoring  >  http://support.apple.com/kb/HT1414
    Make sure you have the Current Version of iTunes Installed on your computer
    iTunes free download from www.itunes.com/download
    3: If Unable to Restore, try using the Steps in this article to force the device into Recovery Mode.
    Note on Recovery Mode.
    You may need to try this More than Once... Be sure to Follow ALL the Steps...
    After you have Recovered your Device...
    Re-Sync your Content or Restore from the most Recent Backup...
    Restore from Backup  >  http://support.apple.com/kb/ht1766

  • Why does the power button intermittently fault -- Not work to wake up the phone?

    Iphone 4 occassionally won't respond to the power/sleep button.  Isn't stuck -- works normally much of the time, but occassionally acts as though the battery is dead.  Have to plug into a power source to activate phone.  Battery will show same charge it had before it went into sleep mode.  Can be near fully charged and proceed working for the rest of the day just fine.
    Button does not stick or seem faulty in any way.  But, when you least need it to not work - such as in travel - or for emergences and have not power source to get to -- is bad.  An unreliable phone for a doctor is not good.  I have presented the problem to a few repair shops who are either not familiar with this behavior or suggest that is may be software rather than hardware.  Something miss reading the battery to the phone indicating that the battery is dead when in fact it is not.  Had the phone restored at the Apple store and this did not solve the problem.
    It seems I did run across a blog that this occurred with some IOS update?
    Would be grateful for advice.
    Thanks

    Hi
    I found this tip on the net.
    Plug phone cable in (powered), press and hold button until voice control is activated, release, unplug.
    http://forums.macrumors.com/showthread.php?t=1328312
    I have not tryed it my self but it may work..
    There are a simular trick to get the home button to work, here it is.
    Open a default iOS application, such as Stocks, Calculator, or Weather
    Press and hold down the Power button until the “Slide to Power Off” dialog appears, then release
    Now press and hold the Home button until the “Slide to Power Off” screen disappears, quitting the application.

  • Resetting Phone with No Power Button and iPhone Not Backed Up Message Blocking the Slide to Power Off Feature

    I've learned how to reset the phone after an iPhone Not Backed Up message cannot be clicked off of, but my Power button is not working and I've been using the greyed out screen button to lock the screen and power off. Now it is not working to turn the phone off for a reset because the iPhone Not Backed Up message is in the way of sliding the power off feature on the screen. Do I have any options?

    Try a reset:
    Hold the Sleep\Wake and Home Buttons until the screen goes dark and the Apple logo appears

  • HT1343 Power button – for Standby not working anymore

    Power button – OS X Mavericks
    Tap to power on. Once powered on, tap to wake or sleep.
    This shortcut is not working after update anymore. My system is 10.9.2 . is it possible to define the power button pressed shortly to standby like it was before?

    It was change because laptop owners couldn't keep from accidentally hitting the power button when reaching for the delete key.
    Press and hold for about 2 seconds to get sleep.
    Press and hold for about 4-5 seconds for dialog box.
    Press and hold for about 10 seconds to force shutdown.

  • IPod Touch 5 home button, power button and charging not working!!

    I have an iPod Touch 5 I got last year for Christmas, so it's about an year old. The home button has not been working recently so I tried everything to fix it but nothing worked. We took it to places to get it fixed but it costed a fortune that I would have bought a new iPod Touch instead. I just used the Assistive Touch instead. Then today I was using my iPod Touch and I turned it off. About a minute later I went to get my iPod Touch and used it again and threw it on the bed because that's what I always do and it never breaks. Then a few minutes later, I got my iPod Touch from my bed and I tried to turn it on but it wouldn't budge. Then I remembered it had low battery so it must have shut down because it had no more battery power left. I charged my iPod Touch and tried to turn it on a again but i wouldn't. It would normally turn on and show the Apple Logo and go directly to the lock screen but it just stayed black. I searched up how to fix this but the only way to turn it back on is doing something with the home button but I couldn't since it was broken. I tried to find computer but they were all occupied and the only that wan't occupied was a Chromebook but it my USB couldn't fit in because it was too big. I try to find other ways but there was nothing that could work. I think my iPod Touch isn't charging because whenever I charge my iPod and it has no battery power left, it would usually turn on by itself. I really don't want to go out and fix my iPod at a store because it'll cost a fortune. Please help!! Thank you

    Turn on without Home/Power Button
    You need a computer with iTunes which rules out a Chromebook

  • MSI X58 Platinum - power button after hibernate not working

    Hi,
    I have MSI X58 Platinum board that is having a problem recovering from hibernate state.
    When I press the power button, it will turn on for about 2 seconds before shutting off again. Nothing is shown on the screen.
    After pressing the power button several times more, it will then power up again and wake up from the hibernation. Everything is back to normal after that.
    It used to work fine where single press to the power button is all it takes to wake up.
    Has anyone experience this problem? It has no problem going to hibernate state (S3).
    Thanks.

    Ok, here's my complete configuration:
    1) Motherboard: MSI X58 Platinum
    2) Processor: i7-920
    3) BIOS version: 3.80 (latest version)
    4) VGA: Inno3D 8800 GT (512 MB DDR3)
    5) Memory: 3 x 2 GB (Corsair DDR3 triple channel)
    6) Hard drive: 300GB (Western Digital Velociraptor) + 1TB (Western Digital Caviar Black)
    7) Optical Drives: DVD-RW (Asus), DVD-ROM (Asus)
    8) Operating System: Windows 7 Ultimate (64 bits)
    9) Power Supply: Sensonic 650 Watt

  • HT4528 power button and screen not working - is this fixable and where do I go?

    Last night my phone was knocked out of my hand and fell hard on the sidewalk.  It doesn't look broken, I have it encased in an Otterbox but I can no longer see my screen, where do I get it fixed and is it fixable?  Also a couple weeks ago my power button stopped working.  Where do I go to get this fixed or do I have to get a new phone?  I didn't get the insurance as I never had an issue with my phones before this.

    Hi dreamy2273!
    I have a link that can help answer these questions for you:
    Contact Apple for support and service
    http://support.apple.com/kb/he57
    Thanks for coming to the Apple Support Communities!
    Regards,
    Braden

  • Replaced screen power button and lcd not working

    I just replaced the lcd/digitizer on my ipod touch 4.  The lcd turns on only if plugged to charge from a dead battery, otherwise, I can't get it to turn on at all.  I can't reset it either, as the power button doesn't work.  More than 1 problem,  I'm sure.Any thoughts?  Itunes doesn't see it either.  I have made sure the connections are good. 

    Very likely you damaged something when replacing the screen.
    - Try taking it a part and verifying that everything is correct.
    - Take it to someone with more experience.

  • HT5957 I have downloaded the ios 7 for my ipad and now my screen is locked and shows a plug pointing towards an itunes symbol.  Does anyone have an way out of this frustrating problem?  Holding down the home and power buttons together has not worked.

    I have downloaded ios 7.2 update for my ipad and now my screen is locked and shows a picture of a plug and the itunes symbol.  Does anyone have advice to fix this frustrating problem?  I have seen help online for iphones, but none for ipads.  The screen will not budge.  I have tried holding down the power and home buttons at the same time, to no avail.  Please, can some of you smart people help me?

    Hi there Martha250,
    I would recommend taking a look at the troubleshooting steps found in the article below.
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    -Griff W.

  • Ipad will not slide to unlock. have tried home key and power button and still wont work

    Ipad will not slide to unlock. Have tried home key and power button but has not worked. Help please?

    Did you input you correct passcode? The iPad may be disabled.
    How can I unlock my iPad if I forgot the passcode?
    http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
    iOS: Device disabled after entering wrong passcode
    http://support.apple.com/kb/ht1212
    How can I unlock my iPad if I forgot the passcode?
    http://tinyurl.com/7ndy8tb
    How to Reset a Forgotten Password for an iOS Device
    http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
    Using iPhone/iPad Recovery Mode
    http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
    You may have to do this several times.
    Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
    ~~~~~~~~~~~~~
    ‘iPad is disabled’ fix without resetting using iTunes
    Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
    I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
    Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
    1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
    2. Open iTunes with the iPad disconnected.
    3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
    4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
    5. Click ‘Setup as new iPad’ and then click restore.
    6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
    7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
    8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
    If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
    ~~~~~~~~~~~~~
    Try it and good luck. You have nothing more to lose if it doesn't work for you.
     Cheers, Tom

  • My iphone's screen goes black and it behaves like that it is switched off.No switches work and the power button also does not respond.The ringtone do not also respond.The only way to switch on the phone is to press  home button and  power button together.

    My iphone's screen goes black and it behaves like that it is switched off.No switches work and the power button also does not respond.The ringtone do not also respond.The only way to switch on the phone is to press  home button and  power button together.

    Pressing the Home button and the sleep/wake or on/off button together until you see the Apple logo and then release is called a reset.
    If no change after a reset, the next step is restoring your iPhone.

  • I have reached out  to this community as my Iphone display gone black and got the solution to keep home and power button pressed. It worked but I would like to know why it went black

    I have reached out  to this community as my Iphone display gone black and got the solution to keep home and power button pressed. It worked but I would like to know
    1. Why it went black and is there a permanent fix for this
    2.Will the IOS gets automatically updated as I feel the IOS was 5 when I got the phone in 2012 december
    3.Do you suggest 7.1 for Iphone 4

    1. There is no way of knowing. These things happen.
    2. The iOS only gets updated when you want it to be.
    3. You should always update to the latest iOS your phone will support. Apple do not write the updates to make your experience worse.

  • I tried to restore my iphone 5s but it shut off during the restore and wont turn back on I tried reseting it with the home and power button but it doesnt work and I tried connecting it to itunes but it doesnt show up

    I tried to restore my iphone 5s but it shut off during the restore and wont turn back on I tried reseting it with the home and power button but it doesnt work and I tried connecting it to itunes but it doesnt show up

    Did you try to connect in recovery mode, as explained in this article?
    If you can't update or restore your iOS device
    If this does not work, get it checked by an Authorized Apple Service Provider or by Apple:
    iPhone - Contact Support - Apple Support

  • HT4623 iOS 6.1 no longer available because you are no longer connected to the internet- this is what my iphone 4 shows. iv tried switching off again and again, closing apps by double tapping the home button but still not working. please help.

    this is what my iphone 4 shows. iv tried switching off again and again, closing apps by double tapping the home button but still not working. please help.
    is there any other method to download ios 6.1.2.
    my phone is not being recognized by itunes on my new windows 8. neither its working on touch copy.
    kindly help.
    thanks

    well in thatcase, i need another help .
    thanks for your instant reply.
    i have currently bought a new laptop (windows 8) and my iphone is not being recognized by itunes.
    because i have no backup on my previous laptop, i downloaded touchcopy but even touch copy is not recognizing my iphone.

Maybe you are looking for

  • Running XI and 6.5 Services on same Business Objects Server

    We are currently thinking about  migrating to Business Objects XI from 6.5 SP4. We are running with a 3-tier architecture, with the Business Objects services running on a Windows Server. Due to the number of users and reports in circulation we would

  • XML Parser for Java v2. Applying XSLT to DOM tree

    I encountered pretty weird behavior of XML Parser for Java v2. While applying XSLT to XML document created in memory using DOM interface I couldn't access element attributes. For example, given the XML document: <root> <Item ID="00001">Value of Item

  • How to test the parameters *SQLNET.INBOUND_CONNECT_TIMEOUT

    Dear all, I want to test the parameters SQLNET.INBOUND_CONNECT_TIMEOUT, I have set the SQLNET.INBOUND_CONNECT_TIMEOUT=10, but i can not how to test it.

  • Macbook pro starts up in windows always help change to leopard

    I have just reinstalled windows vista i bootcamp as i got the blue screen of death before ( windows rubbish) however i need sometimes , anyway since my reinstall the computer always starts up in Windows where as before it started in Leopard and if i

  • EVDO Rev.A support

    I could not find any previous posts on this topic but does anyone know if RIM is planning on a firmware upgrade to allow 8830 CDMA phones to take advantage of EVDO RevA speeds?  A lengthy call to VZW seemed to indicate that the radio hardware is capa