HT2497 how to setup airport to work with IPV6
How can I setup my AE to work with IPV6 that was launch last night in the east coast? Or there is no need for me to do anything on my AE because it will setup itself automatically?
Thanks,
TCFL
IPv6 service comes in a variety of "flavors" so it would be difficult to provide you with exact configuration settings for your AirPort router.
I would first check with your ISP to see if they have implemented IPv6 service. If they have, they should provide you with what requirements must be satisfied to use IPv6.
Similar Messages
-
How to setup AirPort Time Capsule with static IP?
Untill few days ago I have been using Airport Extreme as router for my network. It was cabled to the modem from my internet-provider.
I had 2 printers, 1 iMac, 1 MB-Pro, several SONOS-devices, iPhone, Loewe-TV and iPad setup for it.
AND IT HAS BEEN WORKING GREAT FOR MORE THAN 4 years
Then I bought my new Time Capsule:
It is connected in the same way as the Extreme but now via a static IPadress.
The Airport-Utility says that I am using these set-ups:
Internet - connection "DHCP"
Network - "DCHP+NAT"
The STATUS is:
"DOBB. NAT"-message at the Airport-utility.
Internet-connection is VERY-good and with high-speed.
I am NOT able to get connection to the TV - it shows 100% connection but will NOT allow me to connect to it (password IS correct:-)
It is only possible to get connected to the one SONOS Play:5 which is connected to the Internet - all the other devices can only be connected when I change the network-setting in AirportUtility from "DCHP+NAT" to "OFF (bridge)".
I have been told that when I am using a static IP-adress for my Airport then "DCHP+NAT" is the right setting in order to make the Airport set-up dynamic-adresses for the wireless connected devices.
I am not very-clever in this - but an old man who wants to get the right advice from a clever-person in order to find a solution.
ANYONE inhere who wants to help me?
THANK YOU in advance,Sailalong wrote:
Untill few days ago I have been using Airport Extreme as router for my network. It was cabled to the modem from my internet-provider.
I had 2 printers, 1 iMac, 1 MB-Pro, several SONOS-devices, iPhone, Loewe-TV and iPad setup for it.
AND IT HAS BEEN WORKING GREAT FOR MORE THAN 4 years
Then I bought my new Time Capsule:
It is connected in the same way as the Extreme but now via a static IPadress.
The Airport-Utility says that I am using these set-ups:
Internet - connection "DHCP"
Network - "DCHP+NAT"
I am unclear as to what has a static IP address. And why did you change the setup.. Would it not have worked in exactly the same way as the Extreme?
Is the static address in the WAN setup or the LAN side setup?
Lan side it should be fine.. WAN side is not fine. There are strict rules to apply to using static IP on WAN.
If you can fill that in, it will help me understand the rest.
Also have you updated the firmware in the TC yet? As soon as you have a WAN connection please do a firmware update as there are major issues with SONOS.. which requires Spanning Tree Protocol to work. Apple bungled that one in the first firmware of the TC.. so you must have 7.7.2 and I am not sure it is fully repaired even in that.
I hope you did not reset your AE yet.. sometimes it is better to stick with what works and use the TC in bridge to it. -
How to setup discoverer to work with portal in future
Hi,
I have to setup the environment for a discoverer 10g R2 based reporting application.
The application is supposed to display reports on the portal that is hosted on Oracle 10g AS.
I started with installation of Oracle 10g R2 DB server. I have the Oracle BI suite 10g , Oracle 10g AS, Oracle 10g Portal etc with me.
Can someone guide me as to how should I proceed in the installation step-wise so as the repoting application can be hooked on to the AS and displayed in portal.
The slight catch here is there is a separate team working on developing the portal.
I need to know what is to be done so that there is a smooth merger of discoverer with the portal.
Thanks
GogaHi
The interaction between Discoverer and Portal takes place after you have installed the full-blown application server. Stand-alone Discoverer cannot be made to hook into Portal.
When you install the full application server you need an infrastructure database. You either do this manually by inserting the repository components into an existing database or you use the seeded database that comes with the install. Personally, I prefer the seeded approach.
After you have installed the infrastructure you run the installer a second time and install the middle tier. While you can install the infrastructure and middle components onto the same machine, performance is better if you use different machines. However, if you are only trying to test things out, doing all of this on one machine would be ok.
After you have got your middle tier components installed (Discoverer and Portal), make sure they are working. For Discoverer you will need to have an EUL. For Portal you only need to be able to connect to it.
Next, and only now comes the link between Discoverer and Portal. All you need to do is tell Portal that the link is to be enabled. This is called creating a portlet provider.
To create a portlet provider for Discoverer follow this workflow:
1. Connect to Portal as Portal user
2. On the top right, click the Administer tab
3. You will see three further tabs, this time on the left, called Portal, Portlets and Database
4. Click the Portlets tab
5. Locate the Remote Providers box on the top right hand side
6. Click Register a Provider
7. In Provider Information enter the following:
a) a name - for example Discoverer
b) a Display name - for example Discoverer
c) Timeout - for example 30 seconds
d) Timeout message - for example Please try again later
e) In implementation Stype select Web
f) Click the Next button
8. In General Properties enter the following:
a) In URL type http://hostname:port/discoverer/portletprovider
Eg. http://server1.learndiscoverer.com:7778/discoverer/portletprovider
You may need to omit the port on some systems so that it would look like this:
http://server1.learndiscoverer.com/discoverer/portletprovider
Note: type discoverer/portletprovider as stated
If you do need a port and are unsure as to which port number to enter follow this workflow:
i) Launch a second browser window
ii) Type http://hosntame:1811 (or whatever is the AS Control port on your system) and press Enter
iii) In username enter ias_admin and the associated password
iv) When authenticated, you will see the Farm for your infrastructure and mid tier
v) Cick on the mid tier instance (you may need to enter your ias_admin username and password again)
vi) Click the Ports link alongside the word Home at the top of the screen
vii) Note the port number for your HTTP Server Listen(non-SSL) port
viii) Close AS Control and go back to the portlet provider setup
b) Check the box Web provider in same cookie domain as the portal
c) Leave other defaults as they are and scroll down to section called User/Session Information
d) In User/Session Information check User and specify that the frequency should be Once per user session
e) Click the Next button
8. In Grant Access leave this alone and click the Finish button
9. If you get a warning about the cookie domain click the OK button
10. Exit Portal
You have now successfully created a portlet provider for Discoverer
To test that this is working enter one og these in your browser window:
If using ports:
http://hostname:port/discoverer/portletprovider
If not using ports:
http://hostname/discoverer/portletprovider
The system should respond with Congratulations! You have successfully reached your Provider's Test Page
Does this help?
Regards
Michael -
How to setup ERMS to work with Webforms?
Hello,
we want to use webforms, so that customers can post requests via internet. The webforms will be send by the webserver internal via email as XML-Attachment to SAP-CRM. I can't find any documentation about how to make CRM(5.0) read the informations from this webform and to use these informations for routing with ERMS or even the creation of activities. The ERMS_how_to and ERMS_guide_for_consultants I allready know, but it's only written there, that it is possible and not how. Do I need to setup TREX and a knowledge base also for these functionalities?
Right now it's only possible for us to route these email by subject (created automatical by the webserver)
Will reward points for needfull help. Thx
CarstenHello,
we want to use webforms, so that customers can post requests via internet. The webforms will be send by the webserver internal via email as XML-Attachment to SAP-CRM. I can't find any documentation about how to make CRM(5.0) read the informations from this webform and to use these informations for routing with ERMS or even the creation of activities. The ERMS_how_to and ERMS_guide_for_consultants I allready know, but it's only written there, that it is possible and not how. Do I need to setup TREX and a knowledge base also for these functionalities?
Right now it's only possible for us to route these email by subject (created automatical by the webserver)
Will reward points for needfull help. Thx
Carsten -
How to setup labview for work with Rational ClearCase
Has anyone set-up an interface between LabView and Rational ClearCase.
Have you looked into the tools from V I Engineering? They are about to release a product that does the ClearCase to LV interface
-
How to setup guest net work in airport extreme
Hi,
i have how to setup guest net work in airport extreme?
i have the airport extreme and the airport base station as a range extantion.
all is workig good :-)/
i the init setup (od the extreme) i setup the router to support also guest network with password.
when i scan the network i canor see the guest network.
also i canot set it up from the air play (win7 sp1)
THX :-)Mmm, generally you don't need to do much port mapping in an extreme. Not sure I understand you. What does the d-link do?
-
How do i configure my airport to work with my other wireless router
how do i configure my airport to work with my other wireless router? I want to be able to listen to itunes through my speakers wirelessly.
Please check out the following Apple Support article for details on the many methods to use an AirPort Express for iTunes streaming.
-
How can I make my first generation AirPort Express work with Mountain Lion? I have a 13" MacBook Pro (non-retina).
Hi guys, recently had the same issue. You require an older version of Airport Utility to configure the older Airport Express. It can be found here.
http://www.google.com/url?sa=t&rct=j&q=airport%20utility%205.6%20for%20lion&sour ce=web&cd=1&ved=0CFMQFjAA&url=http%3A%2F%2Fsupport.apple.com%2Fkb%2FDL1482&ei=Ip MBUPLwLoq42wW4puXMBA&usg=AFQjCNGOFUPMM0ZjsKeyj5CcL2oe9Eaf7A -
Will the airport extreme work with Iphone 4 and Ipod 3 gen without a pc or mac.
will the airport extreme work with Iphone 4 and Ipod 3 gen without a pc or mac.
You can setup an Airport device using the Apple Airport Utility for iPhone
Download it for free in the App Store on your iPhone...
It's under "Utilities" and the "Top Free" utilities. -
Does airport express work with PC
Does airport express work with a dell laptop?
Can one setup an airport express for the very first time using a dell laptop?Yes on both. FWIW, I currently have a Dell laptop that has no issues connecting to my AirPort network. I also have AirPort Utility for Windows installed on this laptop when I need to administer the base station. In my case the laptop is running Windows 7.
-
Does Airport Express work with Airport Base Station (not Airport Extreme)?
I'm needing to extend the range of my Airport base station. I purchased an Airport Extreme to funcion as a repeater, but it's not working. Will Airport Express work with a (white) Airport base station. If not, how can I extend the range besides moving the base station?
Can someone actually tell me how to set-up the Airport Express (with my Airport) so that it will act like a repeater. Once again, this is an Airport and not an Airport Extreme.
-
Does Airport Express work with a Windows Computer?
Does Airport Express work with a Windows Computer?
I'm trying to setup an older Airport Express to play iTunes
with a Windows Computer. I just want it to join my network,
since I'm already connected to another router.
Thanks,
PaulIs there a Windows version of the Airport Utility (I think that's what it's called)...
Yes. That is only needed to configure the AirPort Express (AX).
...or do I have to go through Windows setup software?
You may have to do that to get Windows to join the wireless network. -
Is it possible to have your whole family on one apple id or is it better to have each person have there own? If each has their own does each id have to buy their own music and apps? How does find my iphone work with one apple id or two? also I am going to be going off to college soon should I make an itunes id for my self and how will I get all the music from the old id?
Is it possible to have your whole family on one apple id or is it better to have each person have there own?
Yes, it is possible. 1 apple ID can be associated with up to 10 devices.
If each has their own does each id have to buy their own music and apps?
Yes, all purchases are non-transferable.
How does find my iphone work with one apple id or two?
Every device associated with one apple ID through Find my iPhone is tied to that Apple ID; Find my iPhone will work in the same way with up to ten devices associated with one apple ID. You cannot enable Find my iPhone for one device across two apple IDs
I am going to be going off to college soon should I make an itunes id for my self and how will I get all the music from the old id?
If you have authorized a computer with the old apple ID, you can transfer old media purchased through the old to other devices via iTunes. This doesn't mean the media purchases through the old apple ID it transferred to the new account. If you plan to make future purchases and don't wish to share them with others, make your own apple ID. -
Can you setup handoff to work with two mac computers on the same network?
I am attempting to setup handoff to work with two computers on the same network. I cannot seem to get it to work. Should I be able to?
I'm not sure but I haven't seen anything on the Apple site that indicates that it would not work. The following troubleshooting documents may help: Get help using Continuity with iOS 8 and OS X Yosemite - Apple Support
Note in particular the Mac models supported. The other thing that occurs to me is that in addition to being on the same network they would have to be within Bluetooth range of each other. -
I'm trying to use speech recognition to input text on my iMac running the latest mountain lion, 10.8.3.
I have sticky keys enabled.
When I try to start speaking by pressing the function key twice nothing happens. I can only get it to work if I disable sticky keys.
The same problem occurs with all the other modifier keys as shortcut, they do not work with sticky keys.
When I try to select a different shortcut, I am unable to select a two key combination, but am limited to one.
If I select the F6 key, or any other single key, I am able to start speech recognition. However the second time that I press the key, it does not stop recognition and process my words. Instead, it restarts the recognition.
Has anyone figured out how to get speech recognition working with sticky keys enabled?
Or a way to get an individual key shortcut to start on the first press and process it on the second?
Or a way to get key combinations to work, as specified by the help:
Dictation On and Off
To use Dictation, click On.
When you’re ready to dictate text, place the insertion point where you want the dictated text to appear and press the Fn (function) key twice. When you see the lighted microphone icon and hear a beep, the microphone is ready for you to speak your text.
Shortcut
By default, you press the Fn (Function) key twice to start dictation. If you like, you can choose a different shortcut from the menu.
To create a shortcut that’s not in the list, choose Customize, and then press the keys you want to use. You can press two or more keys to create your shortcut.I noticed with version 10.8.4 of OS X that I am now able to select F6 to activate, and the return key to complete the speech recognition. This is still different than the description of how these should function that's included in the help, but at least it's an improvement.
Maybe you are looking for
-
My Iphone 5s shows "No Service" in the specific network area, but if the same sim card is used with other mobiles in the same network area, it shows good network.. i did restore,change sim card, reset all the settings but still not working... please
-
Incorrect Account Determination on Foreign Currency Valuation
Dear SAP Expert, Kindly your help about my issue: My company code using parrarel curreny, 1. Company Code Currency (10) -- USD 2. Hard Currency (40) -- IDR I already complete all customizing for Revaluation such as; OBA1 for gain loss realized and Va
-
Hi, I want to know is it posible to create sales order depending on the ATP for article through customizing if yes can pl. tell me the steps. Atul
-
What is the proper SQL syntax for dates input as variable
Hello, I am working on an ASP JavaScript page that requests totals from an Access database for a specific date range. I can write the SQL statement to query the DB and get the results I need using the WHERE statement below. ...WHERE LABOR_DATE BETWEE
-
when attempting to "save as" a word document and selecting micrsoft word as the "save as type", it no longer will save it in a word icon document, the icon is just a blank document symbol and thus cannot email this document