HT2937 how do i solve idvd not burning double layer disc?

I have an iDVD project that will not burn to a double layer disc. It burns to a single layer with no problems, but with a double layer the disc ejects when it finishes multiplexing and burning. There's still 18 minutes left! I have tried burning it x2 but no luck. Any ideas how to solve this?

How long is the video?
Are you using good media like Verbatim DVD-R DL?
Use the setting Professional Quality:
iDVD encoding settings:
http://support.apple.com/kb/HT1502?viewlocale=en_US
Short version:
Best Performance is for videos of up to 60 minutes
Best Quality is for videos of up to 120 minutes
Professional Quality is also for up to 120 minutes but even higher quality (and takes much longer)
That was for single-layer DVDs. Double these numbers for dual-layer DVDs.
Professional Quality: The Professional Quality option uses advanced two-pass technology to encode your video (The first pass determines which parts of the movie can be given greater compresson without quality loss and which parts can’t.  The second pass then encodes those different parts accordingly) , resulting in the best quality of video possible on your burned DVD. You can select this option regardless of your project’s duration (up to 2 hours of video for a single-layer disc and 4 hours for a double-layer disc). Because Professional Quality encoding is time-consuming (requiring about twice as much time to encode a project as the High Quality option, for example) choose it only if you are not concerned about the time taken.
In both cases the maximum length includes titles, transitions and effects etc. Allow about 15 minutes for these.
You can use the amount of video in your project as a rough determination of which method to choose. If your project has an hour or less of video (for a single-layer disc), choose Best Performance. If it has between 1 and 2 hours of video (for a single-layer disc), choose High Quality. If you want the best possible encoding quality for projects that are up to 2 hours (for a single-layer disc), choose Professional Quality. This option takes about twice as long as the High Quality option, so select it only if time is not an issue for you.
Use the Capacity meter in the Project Info window (choose Project > Project Info) to determine how many minutes of video your project contains.
NOTE: With the Best Performance setting, you can turn background encoding off by choosing Advanced > “Encode in Background.” The checkmark is removed to show it’s no longer selected. Turning off background encoding can help performance if your system seems sluggish.
And whilst checking these settings in iDVD Preferences, make sure that the settings for NTSC/PAL and DV/DV Widescreen are also what you want.
http://support.apple.com/kb/HT1502?viewlocale=en_US

Similar Messages

  • DVD drive not burning double layer discs

    I was burning a double layer DVD this morning, using Verbatim media, which I've never had any problems with. The drive I was using was a Pioneer DVR-A18M. All of a sudden, after I successfully burned one disc and inserted another DL disc, it refused to burn anymore. I forget the exact error message, but it was something along the lines of the media wasn't recognized, and this persisted for multiple discs that I tried.
    Now, yesterday, a friend let me borrow a movie that had a crack in it and the disc came apart in my internal Pioneer drive - but it still worked after that. Odd thing was that the drive would still read and play movies, music, etc but it wouldn't burn anything, tho I don't know if it would burn things other than DL media because I didn't try.
    Anyways, while the Pioneer drive - which I just bought after New Years - had been working well, I decided to replace it due to the fact that it wouldn't burn DL discs and a few other minor issues I'd been having with it. The one main issue was that if I left a disc in the drive for too long, I wouldn't be able to eject it or load any new applications. I'd have to reboot the computer to get the disc out, something I never had to do with the only Sony drive that came with my G5.
    So, I replaced it with an LG GH22. Upon trying it out, it burned a single layer DVD-R, but will not burn a DL disc. The error message this new drive gives me is, from with Toast:
    Sense Key = Illegal Request
    Sense Code = 0x24
    Invalid Field in CDB
    If it would help, I could put the Pioneer drive back in and see exactly what that error message was.
    Oh, one last thing. I'd like to replace the E-IDE cable I have, as disc media is never able to reach its full burning speed potential. I'm guessing it's due to the old IDE cable, as my G5 is from 2005?
    Thanks!

    Ok, I tried using Dragon Burn instead of Toast and it worked fine and the DL disc plays. I have to run out to MCAT class but when I get home, I'll mess around with it some more and try using Toast again, the old drive, etc.

  • IDVD will not burn dual layer disc correctly.

    I have an iMac9,1 Intel Core 2 Duo 2.66 GHz with 8 gigs of ram, with a OPTIARC DVD RW AD-5670S DVD-writable to -R, -R DL, -RW, +R, +R DL, +RW. It will not spit out a properly formated disc from IDVD. I get the "Supported disc not available" message, even though I have encoded it for dual layer in NTSC.
    Has anyone ever experience problems with this? If so, what did you do to resolve it? I've burned through a half a dozen dual layer disc and these are still not supercheap.
    TommyBoye

    Yes I called and my warranty was up so the nerd on the other end tried to sell me the applecare protection program. I guess my next step is to go to an apple store, but as the person that replied last in that discussion said time is an issue. I guess my biggest problem with this whole thing is that it is obviously the update that messed up all of these superdrives, so warranty shouldn't be an issue. Apple even removed the download link: http://www.macfixit.com/article.php?story=20070716082804520&query=superdrive

  • MBP C2D - Problems burning Double Layer Discs

    I encounter massive problems when trying to burn DVD+R DL Discs. The MBP C2Ds internal drive is supposed to burn DL media but the only way to burn them is under win xp using my external philips ED16DVDS usb2 burner. Nero produces coasters using the internal matshita burner.
    Under Mac OS Toast as well as Mac OS X give me error messages before starting to burn.
    The Media I use is called intenso DVD+R double layer. Intenso media has worked exceptionally well for my needs over the last years. This is no cheap stuff.
    I am thankful for any suggestions.
    MacBook Pro C2D 2,13 GHz   Mac OS X (10.4.8)   Seagate 300GB FW Drive, WD MyBook Pro II 1TB FW800

    Can you tell us exactly what the error message says under Toast?

  • IDVD not burning film onto disc

    I have been trying to burn my film through iDVD. Last week I burned two DVDs with no problem. I now have a new packet of the exact same blank discs, but the burning doesn't work, and the disc is ejected in the multiplexing stage with nothing on the ejected disc.
    I've looked over other threads, and followed their instructions (changing to x1 speed / having over 25GB space before I begin burn) and have also been told to delete the .plist file, but I cannot find it anywhere.
    This is extremely frustrating, as I do not know what has happened in the past week, same project, same blank DVDs.

    Hi
    • Delete iDVD pref. file - or rather start a new user/account - log into this and re-try
    iDVD pref. file resides.
    Mac Hard Disk (start-up HD)/Users/"Your account"/Library/Preferences
    and is named.
    com.apple.iDVD.plist
    While iDVD is NOT RUNNING - move this file out to desk-top.
    Now restart iDVD.
    If You run Mac OS X.7 or more - then the Library in the User-account folder is invisibly and need to be set to be viewable. IT IS NOT in the Library on Root level (when opening MacintoshHD - first window = root level)
    ( It can be done like this: Open Terminal, then enter: chflags nohidden ~/Library
    Press return, then restart, and it will always be visible until the next major update, when you do the same thing again. )
    Yours Bengt W

  • How can i solve "could not load language and text preference "

    how can i solve " could not load language and text preference ".. help everyone...

    Please read this whole message before doing anything.
    This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
    Step 1
    The purpose of this step is to determine whether the problem is localized to your user account.
    Enable guest logins* and log in as Guest. For instructions, launch the System Preferences application, select Help from the menu bar, and enter “Set up guest users” (without the quotes) in the search box. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
    While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
    Test while logged in as Guest. Same problem?
    After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
    *Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
    Step 2
    The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
    Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
    When you see the gray Apple logo, release the shift key.
    If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.  The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    *Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode.
    Test while in safe mode. Same problem?
    After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

  • Burning Double Layer DVDs in iDVD 6.0.3

    I can't seem to burn double layer DVDs. I am using an intel iMac which says i should be able to but it won't accept discs to burn.
    Is it because i am using 8.5GB discs because iDVD says in the project info that double layer DVD should be 7.7GB?
    Any thoughts...?

    I am having the same problem!
    I am Using basic DVD+R DL discs.
    Under "Project" and "Project Info" i change the "DVD Type:" to "Double-Layer (DL) - 7.7 GB"
    the burn process will act completely normal until the very end.
    It will spit out the disk and stick on "cleaning up" or on "writing lead-in".
    Then, when DVD is reinserted in to the computer, it will read it like a blank disk (it gives you the "you have inserted a blank disc" menu).
    If any one has any idea what's going on please let us know. it would be extraordinarily appreciated!

  • Trouble burning Dual-Layer discs using various programs... suggestions?

    Hello, I could really use some constructive, helpful recommendations here. I've been trying to burn some large (5+ GB) disc images (ISOs, but mostly VIDEO_TS files) to a Dual-Layer disc that would play on a regular DVD player.
    So far I've tried a couple different DL disc brands (HP, Memorex), and various programs (Finder, Liquid CD, even Toast Titanium 10 seems to have a hard time doing so), but without much luck-- mostly just end up with coasters.
    Have you had this problem trying to burn Dual-Layer discs? And what's a good freeware/shareware program or method that's done the job that you can recommend? I have at least 75GB of space on my 250GB drive (so I would imagine that's enough for any temp burn folder purposes...)
    Thanks!

    I use Verbatim usually and never have any problems so try one of those if possible, but before you do run a DVD Lens Cleaner disc through it as just a small spec of dust or dirt can sometimes play havoc.
    I burn most things with Toast or the Mac OS itself.

  • How can I use iDVD to burn movies I legally purchased online?

    Please help, I have an older macbook pro with updated iDVD program. I am new to making DVDs so I have been watching and reading and trying to find any info on how to burn a dvd that can be played on any dvd player. I have purchased movies through itunes over the years and want to be able to use them off of my laptop, and i also have torrents that I want to burn. they are all either .avi or .m4v  and every time i import them into the iDVD project it will show the titles of the chapters but no movie, no pictures, and will not even autofill dropzones! Please help, I have read that i need to make the .avi into .mov but i don't have the slightest idea how to do that without paying for something to slow my computer down even more. Any solutions that are not too complicated or expensive?

    From iTunes Help:
    Movies and TV shows purchased from the iTunes Store can’t be burned to a DVD or VCD that will play in a DVD player or Video CD. 
    As for the various .avi and .m4v files, you need to convert them to something that iMovie can use, like DV,, and then pass it to iDVD for burning - always assuming they are not copy protected and you are not breaching copyright.
    For that you need mpegStreamclip:
    http://www.squared5.com/svideo/mpeg-streamclip-mac.html
    which is free

  • IDVD not burning SOME transition frames

    I have an imovie 06 movie where I set chapters and transitions. When I burn the DVD (I have tried 3 times) the first 4 chapters and transitions work OK, but on the final 6, the 4 second transition frame with the title I set in iMovie mysteriously drops out. Any idea what could be causing this. Maybe an incompatibility between iMovie 06 & iDVD 08?
    I've been trying to burn this movie for a week! I already reverted back to imovie O6 when I realized how awful imovie 08 was (NO CHAPTERS!) Now this is just the latest iDVD 08 headache. From what I've read it seems a little more difficult to revert to iDVD 06. Is that true?
    Message was edited by: John Hall3

    Actually, I just looked at the disk closer, and the transition frames actually ARE there, but the chapter markers are not burning in the right place, so when you hit the chapter, the title frame is already over. When you place the movie in iDVD before you burn it, everything is aligned properly.

  • Please help! why is the DVD burner not burning dual layer media in my G5?

    I have tried, unsuccessully, to burn dual layer DVD's on my G5 using the latest iDVD software (iLife '08) but to no avail. I switch to dual layer in iDVD but invaribly, I always get a multiplexing error at the end of the burn. Any suggestions?
    Rick

    Are there any plans to update OS 10.4.11 to include a firmware update for the DVD drive? Or has it already been changed in Leopard?
    Depending on what model of Superdrive you have, there may be a firmware update from the manufacturer, just not from Apple. Updating to the latest firmware from the manufacturer often provides for better media compatibility, faster burn speeds, and sometimes even features that were disabled by Apple's version of the firmware.
    DVD-R DL discs have one major drawback if you're using them to burn video DVDs - you have no control over where the layer break is placed. The first layer must always be filled completely before any data is written to the second layer. DVD+R DL does not have this limitation. You can place the layer break anywhere you like, just as long as the first layer is more full than the second.

  • HELP: Burning double layer DVD does not work as expected by project info

    Hi,
    I have the following problem: I created an new project in iDVD and choose the following settings in the project info: Video-Modus=PAL, Coding=HighQuality, Format=16:9 and DVD-Typ=DoubleLayer. When I saved the project and open it again the project info dialog shows me the following amounts of used space: 1867 MB DVD-ROM, 4595 MB Diashows, 128 MB Menus, 0 MB Film, alltogether 6,48 GB and 200 minutes of duration.
    NOW: When I choose to burn the DVD it first tells me that I need to use a double layer DVD because the project is too large to be burned to a normal DVD. If I press OK (having inserted the DL-DVD), I am back in the standard iDVD editing mode. If I then have a look to the settings in the project info it is as follows: 3733 MB DVD-ROM, 4595 MB Menus, 128 MB Menus, 0 MB Film, alltogether 8,31 GB and still 200 minutes of duration. This obviously does not fit to the 7,7 GB DL-DVD so I cannot make iDVD to burn my DVD...
    QUESTION: What happend ? Why doubled the DVD-ROM space ? In fact what I can see is that there are several diashows doubled and even lots of picture more than once on the DVD. Could it be that there is a trash somewhere implemented ? I cut and pasted some of the diashows to a different place on the DVD...
    Thanks for answers and support.

    In fact what I can see is that there are several diashows doubled and even lots of picture more than once on the DVD.
    Do you mean "slideshows" instead of diashows?
    Did you add anything to the dvd-rom section of the DVD? If not, you may want to check this section to see what's going on.
    Also what does map view look like? Does it show anything that may have been duplicated?
    Please tell us your current ecoding settings.
    In other words, is the encoding set to Best Quality, Best Performance, or Professional Quality?
    Lastly, is this Dvd made up of of only slidesshows / images? Or did you also add a movie/s with actual video footage? And if so, what is the total playback / run time of this Dvd in hours and minutes? (keep in mind iDvd doesn't look at size/s but rather total QT playback in minutes; not to exceed 120 mins per SL Dvd-R and twice that amount for DL media).
    Message was edited by: SDMacuser

  • Will not burn photos to disc

    iPhoto will not burn photos to a DVD disc(Maxell DVD+R).
    iMac response is:
    "The burn to the SuperDrive drive failed. The disc drive didn’t respond properly and can’t recover or retry."
    These Maxell DVD's are probably 2+ years old. However, I was able to burn 2 disc early this morning. Could it be a heat problem with the SuperDrive?
    Your Thoughts?

    If you have burned 5 or 6 disc in a row then maybe heat could be a concern.  I don't think so with just 2.  Are you able to burn a disc, CD or DVD, from the Finder or is it just from iPhoto?
    Run the Apple Hardware test as described here: OS X Mountain Lion: Use Apple Diagnostics or Apple Hardware Test
    OT

  • How does it work? SuperDrive with double-layer support

    Hi,
    Can anyone help me? I own a macbook with SuperDrive with double-layer support. I want to try to burn a dvd with the dual layer, how does this work? Which applications do i need? I have been searching for info on this subject but havent succeeded so far..

    Any standard burning application such as Toast (or OS Xs built in burning) will burn a dual layer disk. You don't need to do anything special... it will just see the disk with double the capacity. What you do need to do is get dual layer DVDs. They're not all that easy to find at many retail stores, but they're pretty easy to find online.

  • Help! Can't Burn Double Layer DVD

    I bought some Double Layer DVD+ DVDs to archive photos and other files for storage in my safe deposit box. When I try to burn the DVD from the finder I get the message that an unexpected error has occurred. The disk does not even get burned. I can reinsert it into the internal DVD drive and it shows up as a blank DVD. The following is from my system profiler:
    MATSHITA DVD-R UJ-845:
    Firmware Revision: DBN9
    Interconnect: ATAPI
    Burn Support: Yes (Apple Shipped/Supported)
    Cache: 2048 KB
    Reads DVD: Yes
    CD-Write: -R, -RW
    DVD-Write: -R, -RW, +R, +RW, +R DL
    Burn Underrun Protection CD: Yes
    Burn Underrun Protection DVD: Yes
    Write Strategies: CD-TAO, CD-SAO, DVD-DAO
    Media: No
    How can I archive the files to a DVD +R DL disk?
    Thanks in advance.

    Thanks for the advice. However, I bought these DVDs at a closeout sale. They are labeled "Comp USA" who has gone out of business. I bought a spindle of 20 DVDs for $9.95. I wonder why the DVD burner is so particular?

Maybe you are looking for