HT3024 i need help on the network settings on the imacd g4
I need help with my Internet settings on the inaction G4
Hello,
What Interface are you using? Built-in Modem for Dialup, Ethernet or Airport to a Router or Modem?
Similar Messages
-
I updated my 4S phone to IOS 7.1.2 and lost my wi-fi. The wi-fi is on, but can't find ANY networks. I have been through all the steps, from turning the phone on and off, resetting the network settings, resetting the whole phone, redownloading 7.1.2 and lastly going to the Apple store for help. They tried all the exact same steps I did, took the phone apart and looked at and said it is in "pristine" condition. They have no idea why it isn't working, but they could offer to sell me another phone. This is extremely annoying! They claim it has nothing to do with the update to 7.1.2, but that is when I lost the wi-fi, so it has to be related!
My 4s i-phone which is 2 years old cannot find any wi-fi networks not even my home network... I had the same problem two months ago but i turned off the i-phone for 8 hours and then it was okay... Now it happened again.... I tried to restart the modem but whilst my laptop is connected regularly, my phone still cannot find any wi-fi networks... I restart the i-phone, i reset it, i chose reset network settings, reset all settings, i turned it off for a whole day in case it was overloaded, i turned on the airplane mode and turned it off again, i put it into the freezer for 10 minutes within a zipped bag but 3 days now and i still cannot be connected to my home wifi... I went to the technician today and he told me that it means that wi-fi is broken and that i need to change it with a charge of 70 euro but i have to give my phone for 10 working days so as to be fixed... I am so frustrated and i don't know if i want to give 70 euro for wifi since i don't know if it would make the same problems again...
-
My iphone 4s cannot join a public unsecured network, but my ipad and macbook can with no problems. I have reset the network settings on the iphone twice. Both times that fixed the problem but only for a few minutes, then I get the "cannot join network" message again. Please help! What can I do?
Anyone have any ideas or information to help with this? Any help and consideration is MUCH appreciated.
-
I can' see my apple tv listed on airplay. iI have scrolled through the entire list and mine is not there. I can see other apple tv devices on the network but not mine. I'm using an ipad 2. I have checked the network settings between the devices and they're OK. Any thoughts?
Hi jl5653,
Thanks for using Apple Support Communities. Based on what you stated, it sounds like the Apple TV is not listed in the selector window. I would recommend that you read this article, it may be able to help the issue.
iTunes: Troubleshooting AirPlay and AirPlay Mirroring - Apple Support
Cheers,
Mario -
My ipod touch wont connect to wifi after i reset the network settings
my ipod touch wont connect to wifi after i reset the network settings
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
iOS: How to back up your data and set up as a new device
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
i hv a macbook and hv not been able to figure out whr to enter d gateway pathway in the network settings so as to get my internet started on my machine.. help me..
If you go to System Preferences (under the Apple menu) and select the Network pane, then select the interface you want to use (probably Wi-Fi or AirPort if you are wireless, or Ethernet if not.) If using a static IP address you can set your router address here. If you are using DHCP, it is not needed, since the computer will pick it up automatically.
Best of luck. -
My wi-fi connection is enabled, however Safari is telling me the server stopped responding. My laptop is working fine on the same wi-fe network. I have reset the network settings and still Safari will not open any web pages. Help!
Ralph..........Did as you suggested and I am still getting the message "Safari could not open the page because the server stopped responding". I am not able to connect with anything on the Internet. Frustrating since I am able to connect with my laptop. Thanks for the suggestion.
-
How do I change the network settings on my Apple TV? We have two wireless options and need to switch.
Welcome to the Apple Community.
Settings > General > Network > WiFi and select your network. -
The wi-fi in my iphone 4S is 'greyed out' and i am not able to switch it on. I have tried resetting the network settings but nothing happened. I can't even download the new iOS7 version as it requires WI-FI to do so. Please help.
I had same problem. I removed the back cover, and warmed wi-fi module by hairdryer of my wife). five days wi-fi works great. I do not know what will happen next.
during operation iphone must be turned off. time of heating is near five minutes. wifi module is located upper the battery, on the upper right corner of device. -
New airport user need help setting up a pc on the network
went and bought a airport extream today and my mac works fine on it but i also have a pc and need help getting it to work with the airport express. it seems to see the airport in the network slection screen but after i put in the pass i get nothing and it returns to the "chose a wireless network" can anyone help?
Thanks for the reply.
That's interesting, I guess I had assumed that would be a basic thing.
Right now the 4000 number is in port 1, and then 4244 is in port 2. So if no one else is on the phone, and my boss picks up his phone, dials 9 then XXX-XXXX, he will be routed outbound on the 4000 line on port 1. Then while he's talking, if I pick up the phone and dial 9 then XXX-XXXX, I will be routed out on the 4244 line on port 2.
Am I understanding that correctly?
If that is the case, then that is a bit frustrating. Our 4000 line has everything on it, call waiting, caller id, long distance, etc. But the 4244 line is just a basic service. So if I'm calling local or toll free, I don't want to tie the other line up in case someone else needs to make a long distance call to a client. Is there any work around to that at all? Is there any way to use steering digits to point the call to the right line? Would we have to put the PSTN lines on seperate SPA400's?
Again, any comments and suggestions are much appreciated!
Message Edited by VoIP_Me on 07-30-2008 06:27 AM
Message Edited by VoIP_Me on 07-30-2008 06:28 AM -
My WiFi on my iPad has been getting poorer recently, and two days ago stopped working completely. I have reset the network settings, and when that didn't work I restored my iPad. I still cannot find or access WiFi networks, and if I do, it fails. Help!!
My WiFi on my iPad has been getting poorer recently, and two days ago stopped working completely. I have reset the network settings, and when that didn't work I restored my iPad. I still cannot find or access WiFi networks, and if I do, it fails. Help!!
-
Hello, my name is brad and I recently had a voicemail app that I was using and now i got rid of it. But now my voicemail for the phone will not work. I tried to reset the network settings and nothing happened. I was wondering if you could help me out?
When you set up a voicemail redirection, usually you have to remove that redirection from the account that redirected it. Like Google Voice, if you activate Google Voice to receive your voicemail, you will have to log into voice.google.com to turn it off. If you contact your carrier, they can tell you exactly what program has taken over your voicemail functionality just in case you are stuck, but if you know the name of that App, I'm sure you will be able to figure it out. Hope this helps you out.
-
Since I bought this iMac more then 2 years ago, I wasn't really bothered that this feature (airport) didn't work in my iMac as I connected my iMac directly via Ethernet to the routher. The wireless router then connects to the other devices in my house. But I want to move my iMac to another room and need the airport-card to work. It was bought with it, but it has never been switched on. Any suggestions, where to check:
1.if the aiport-card has been installed when I bought it?
2. if yes, how to switch it on? it doesnt pop-up on my screen when I use the '+' in the network settings? Only 'ethernet' and 'blue-tooth'.Is there a way to see if the actual hardware with driver has been installed in the iMAC?
it shows that tht following software versioin are installed for Wifi;
Software Versions:
CoreWLAN: 2.1.3 (213.1)
CoreWLANKit: 1.0.3 (103.2)
Menu Extra: 7.2 (720.1)
configd plug-in: 7.4.1 (741.1)
System Profiler: 7.0 (700.3)
IO80211 Family: 4.2 (420.3)
WiFi Diagnostics: 1.0.2 (102)
AirPort Utility: 6.1 (610.31)
But I can't find any hardware in the list of 'system report' that refers to 'airport card'
Is there a way to find out if there is any of such a device built in the iMac at all?
the hardware overview shows: no devices installed of the following:
ATA
Fiber Channel
Hardware RAI
PCI Cards
Parallel SCSI
SAS
Thunderbolt drivers not loaded.
it's a iMac, OS 10.7.5, but started with 10.6 when I bought it, 4GB, ethernet, 27".Wifi never worked.
any other solutions that could work? thanks for your help so far Barry! -
I think I need help with driver (software) settings for D110a
I think I need help with driver (software) settings for D110a all-in-one
Product: D110a all-in-one
OS: Windows XP Professional
Error messages: None
Changes before problem appeared: None--new installation
The quality of photo images (mostly JPG files) in printouts is awful even though the files display beautifully on the PC screen. I am using
IrfanView software for displaying/printing. As far as I can tell, IrfanView is not the problem.
When I print the same images on a Deskjet 5150 attached to a different PC also running XP Pro and IrfanView, the quality of the printouts is at
least acceptable, Some would probably say good or very good.
It's dificult to explain in words the problem with the printouts. A picture of really pretty vegetables (squashes, tomatoes, watermelon, etc) comes
out much too red. Moreover, the red, which appears shaded on the screen, seems to be all one shade in the D110a printouts.
Something similar happens to a view of a huge tree in full leaf. On screen, there are subtle variations in the "greenness" of the leaves. In the
printout, all green is the same shade. In the same printout, the trunk of the tree is all a single shade of grey. It isn;t even obvious that the
trunk is a round, solid object.
I liken the effect to audio that disappears entirely when you lower the volume and gets clipped into square waves in even moderately loud passages.
I don't know whether the D110a driver software permits adjusting the parameters that appear to be set incorrectly, and if adjustments are possible,
how I would identify which parameters to adjust, how I would access them, or how I would adjust them. I'm hoping that someone can help. Thanks.
I forgot to mention that I have used the diagnostic application and it tells me that there are no problems.
e-mail me at [email protected]brazzmonkey wrote:
Hi everyone,
I noticed the following message when network starts on my gateway
Warning: This functionality is deprecated.
Please refer to /etc/rc.conf on how to define a single wired
connection, or use a utility such as netcfg.
Then I realized the way network settings should be written in rc.conf has changed. But I can't figure out how this should be done.
Currently, my set up is the following (old way):
INTERFACES=(eth0 eth1)
eth0="dhcp"
eth1="eth1 192.168.0.10 netmask 255.255.255.0 broadcast 192.168.0.255"
ROUTES=(!gateway)
eth0 is on DHCP because the IP is dynamically assigned my ISP.
eth1 has a fix IP because it's on the LAN side.
No problem to use DHCP on eth0 with the new settings.
But for eth1, I don't know what I am supposed to write for gateway.
Wiki isn't clear on that one either, and it looks like many articles still refer to the old way.
Any guidance appreciated, thanks.
brazzmonkey,
you can't define 2 interfaces the old way (even though I saw some tricky workaround somewhere in the forums).
Use, f.e., netcfg:
Comment your old lines.
In /etc/rc.conf insert:
NETWORKS=(Eth0-dhcp Eth1-static)
DAEMONS=(..... !network @net-profiles ....)
In /etc/network.d create 2 files:
First one is named Eth0-dhcp.
Contents:
CONNECTION="ethernet"
DESCRIPTION="Whatever text"
INTERFACE=eth0
HOSTNAME="your hostname"
IP="dhcp"
DHCP_TIMEOUT=15
Second one is named Eth1-static.
Contents:
CONNECTION='ethernet'
DESCRIPTION='whatver'
INTERFACE='eth1'
HOSTNAME='hname'
IP='static'
ADDR='192.168.0.10'
GATEWAY='192.168.0.1' # your gateway IP
DNS=('192.168.0.1') # your DNS server
The names Eth0-dhcp and Eth1-static are not magic. They just must be the same in rc.conf and in /etc/network.d.
Hope it helps.
mektub
PS: netcfg must be installed.
Last edited by Mektub (2011-07-20 14:07:05) -
Need helping printing to networked printers.
I need help setting up network printers that have a code on them for each individual. There is no place to put a code so the printer will know who is printing what. I have installed 3 printers and they will not print, they just go to a paused mode and when you hit resume in reverts back to pause because it is looking for a code. I have tried it another way but it asks for a user name and password and all we have are codes. The workplace is using a windows based server and the copiers are listed as followed.
Konica biz hub c450
Sharp ar m700n
sharp mx700n
I need help to be able to print from my mac. I also have parallels running with xp installed and all the printers are installed on that side and printing fine. Hopefully someone can help me out.
Thanks in advanceHello and welcome to Apple Discussions.
In order to provide the user with the ability to input a user code, the respective printer driver would have to provide the facility. If this feature did exist on a previous version of OS X, then you may have to check the vendors web site to see if there is a driver for 10.6.
If you are not sure if the function was supported previously, then go through all the user menus for the driver. The function may be present but located in an unusual location. Or it could require an additional file (aka plugin) that could be missing from the driver installation or not compatible with 10.6.
The other thing to note is that if you have the Mac's printing via a Windows queue, you will have to provide user credentials for SMB print queues. This is typically a Windows user account - not the Mac's account details. If you don't want to create accounts for the Mac users on the Windows server, then you can use LPD rather than SMB to connect to the Windows queues. This does require UNIX Printing Services to be enabled on the server.
Pahu
Maybe you are looking for
-
How can we copy personalization from one to an othere resp/function
guys, As we use people and maintain function to maintain employee information, in this function we have made personalization and working fine, but after restricting function which is appearing on others button like (absence, qualification, previous e
-
Lightroom trial doesn't show complete menu selections or import button. Also get error message on launch: An error occurred when attempting to change modules. I am unable to find/see the following file to try renaming the SLCache and SLStore files
-
Mac Mini Pre 2009 Wireless Question
I have 3 ways of accessing my wireless network. My wife's new macbook (5,1), my iPhone 3G and my pre 2009 Mac Mini. All worked in our old house. We just moved and wireless router is located further away from my mac mini. Wife's computer and my iPhone
-
I have Jb0ss 4.0. I have a folder structure like D:\jboss-4.0\server\strong_server\deploy\strong_ctx I have a war file named strong_ctx.war in the above directory Now i want to place one more war named stront_1.war in the same directory. But i am not
-
Whose getting their IP4 on the 23rd?
I don't know about you but I am excited to be getting it tomorrow! Ordered through AT&T! Status: In Transit - On Time Scheduled Delivery Date: 06/23/2010 Shipped To: NEW SMYRNA, FL, US Shipped/Billed On: 06/22/2010 Type: Package Service: NEXT DAY AIR