HT3226 how do I clean dust from inside Mac Pro?

I have compressed air, but I know it also can leave some residue, even when it is held upright (never ever use compressed air from a can held other than upright!). But is there something like a mini-vacuum cleaner? I don't want to blow the dust and cat hair further into the machine. When using compressed air it tends to blow it everywhere...what about compressed air plus holding, nearby, the operating end of a vacuum cleaner hose?

I have just cleaned my Mac Pro. Yes you are on the right track. I pulled out the processor assembly at the bottom, the SuperDrive tray at the top (both very easy), and the graphics card (at little bit harder),  and with compressed air in one hand, and vacuum cleaner in the other, I blowed and vacuumed out all the dust, there was heaps! 
As others have suggested, use the compress air conservatively and in brief bursts, and only when the vacuum can't get to or dislodge some dust. I've had one graphics card fail due to the build up of dust in his fan fins, so I recommend getting it out and cleaning those little fins - which will probably be clogged with dust.
My Mac Pro now runs much quieter, and happier I suspect. 

Similar Messages

  • How can I remove Growl from my Mac Pro

    Hi there!
    How can i remove Growl from my Mac Pro?

    David ..
    Instructions here >  Growl - Removing Growl

  • How can I delete massages from my Mac pro

    How can I delete massages from my Mac pro

    Ok never mind I figure it out, but thank you for responding

  • How do I clean up a SLOW Mac Pro?

    Hi - Finally time to clean up this Mac Pro.  It's gettting slower and slower.
    May I please ask for your suggestions?
    Thank you

    Usually you don't
    What does slow mean or behavior, what apps.
    I wish I had $1 for every such question I see, more so on OS X forum. But also earlier today -
    https://discussions.apple.com/thread/3790641?tstart=0
    Do a clean install after you format a new drive and then after all the updates and insuring it works use Setup Assistant.
    There is no magic bullet.
    Maybe do two Safe Boots. Repair the disk drive. =
    Maybe you already deleted all the browser cache.
    Move the home folder to another drive.
    Add more RAM. Buy an SSD.
    Unplug and disconnect all the devices other than kb and mouse.
    Mac Pro normally don't slow down over time unless you have crashed and froze and haven't repaired the boot drive. Or you have been using the same system drive through two full OS upgrades. A new OS is great time to buy and use a new drive and keep the old one handy as dual boot backup.
    www.macsales.com/macpro
    www.macperformanceguide.com

  • Cleaning dust from inside G5

    Hi
    I've just had a problem
    My G5 2.5Ghz dual just shut down no warning just went off there seemed to be a bit of a burning smell when it did
    I checked it would start up again after i left it a couple of hours to cool down it seems to be ok
    I had a look inside & it looks a bit dusty in there now i have ordered some cans of compressed air but i dont just want to dive in there & start spraying it around
    What things should i be looking for is there anything i need to stay away from spraying what components if any do i need to remove
    If anyone has done this procedure could you please post the steps you took or if you know the procedures again could you please post them
    I have done a search first to see if anyone has done this before & i did find the link someone kindly posted for the service source PDF
    Thanks in advance

    None of the above. What, you think I don't watch the forums?
    The reality is that I very rarely hang onto any hardware longer than two years. I bought the DP2.7 refurbished and it still had 1 year of AppleCare left on it when I sold it. I also started using a kill-a-watt meter to measure power consumption and felt that the PMG5 used too much juice for what I was doing with it. Same goes for the server I sold and moved those operations to a mini. This MBP uses far less juice than either of the G5s and i have the electric bills to prove it.
    As an aside, I've bought nothing but refurbished Macs since they were available from Apple. I don't know if this is a fact, but it sure seems like I never seem to suffer any of the "normal" problems so it makes me think they take care of most of that stuff before shipping them back out.
    However, you've been here long enough to realize that it is true that the majority of the time when someone complains about a dead Mac they have never opened it up and cleaned it out, let alone not having it on a UPS.
    Luck-
    -DP

  • How do I print wirelessly from my Mac Pro to Epson XP-810 printer

    I recently bought a Epson XP-810 printer and conected to my WiFi wireless router ASUS N750. The printer's test sheet states that network is working correctly but a "Router / Access point channel" conflict has been detected. I'm using a macbookpro with the current Maverick OS. The system setting shows the printer is on idle, but when I try printing wirelessly from laptop it doesn't print.
    Any assistance or advice would be greatly apprecite it.

    Do you know the printer's IP? If you have it you can use Network Utility to ping the printer. Its in System / Library / CoreServices / Applications.
    Enter the IP in the empty field, the number of pings you want to send, then click Ping.
    The results might help locate the problem.

  • How do I export photos on my mac pro to my iPad

    Help please....
    How do I export photos from my mac pro to my ipad?
    Joy

    Through iTunes. Use iPhoto to store your photos. iPhoto is part of your iLife applications. Connect your device to the computer and open iTunes. Select your iPad under Devices in iTunes' sidebar. You can now configure what you want to sync to your iPad. When you've dones so click on the Sync button.
    Please get iPad User Guide - iOS 6

  • How do I uninstall mackeeper from my macbook pro?

    How do i uninstall mackeeper from my Macbook Pro?

    You may have installed a variant of the "VSearch" ad-injection malware. Follow Apple Support's instructions to remove it.
    If you have trouble following those instructions, see below.
    Malware is always changing to get around the defenses against it. This procedure works as of now, as far as I know. It may not work in the future. Anyone finding this comment a few days or more after it was posted should look for a more recent discussion, or start a new one.
    The VSearch malware tries to hide itself by varying the names of the files it installs. To remove it, you must first identify the naming pattern.
    Triple-click the line below on this page to select it, then copy the text to the Clipboard by pressing the key combination  command-C:
    /Library/LaunchDaemons
    In the Finder, select
              Go ▹ Go to Folder...
    from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
    A folder named "LaunchDaemons" may open. Look inside it for two files with names of the form
              com.something.daemon.plist
    and
               com.something.helper.plist
    Here something is a variable string of characters, which can be different in each case. So far it has always been a string of letters without punctuation, such as "cloud," "dot," "highway," "submarine," or "trusteddownloads." Sometimes it's a meaningless string such as "e8dec5ae7fc75c28" rather than a word. Sometimes the string is "apple," and then you must be especially careful not to delete the wrong files, because many built-in OS X files have similar names.
    If you find these files, leave the LaunchDaemons folder open, and open the following folder in the same way:
    /Library/LaunchAgents
    In this folder, there may be a file named
              com.something.agent.plist
    where the string something is the same as before.
    If you feel confident that you've identified the above files, back up all data, then drag just those three files—nothing else—to the Trash. You may be prompted for your administrator login password. Close the Finder windows and restart the computer.
    Don't delete the "LaunchAgents" or "LaunchDaemons" folder or anything else inside either one.
    The malware is now permanently inactivated, as long as you never reinstall it. You can stop here if you like, or you can remove two remaining components for the sake of completeness.
    Open this folder:
    /Library/Application Support
    If it has a subfolder named just
               something
    where something is the same string you saw before, drag that subfolder to the Trash and close the window.
    Don't delete the "Application Support" folder or anything else inside it.
    Finally, in this folder:
    /System/Library/Frameworks
    there may an item named exactly
                v.framework
    It's actually a folder, though it has a different icon than usual. This item always has the above name; it doesn't vary. Drag it to the Trash and close the window.
    Don't delete the "Frameworks" folder or anything else inside it.
    If you didn't find the files or you're not sure about the identification, post what you found.
    If in doubt, or if you have no backups, change nothing at all.
    The trouble may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
    This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow. Never install any software that you downloaded from a bittorrent, or that was downloaded by someone else from an unknown source.
    In the Security & Privacy pane of System Preferences, select the General tab. The radio button marked Anywhere  should not be selected. If it is, click the lock icon to unlock the settings, then select one of the other buttons. After that, don't ignore a warning that you are about to run or install an application from an unknown developer.
    Then, still in System Preferences, open the App Store or Software Update pane and check the box marked
              Install system data files and security updates (OS X 10.10 or later)
    or
              Download updates automatically (OS X 10.9 or earlier)
    if it's not already checked.

  • How do I uninstall extensions from my mac?

    How do I uninstall extensions from my mac? I'm trying to uninstall the Greatdy System Audio and Sunflower extensions. It would really be nice if macs had a comprehensive program to uninstall programs and plugins.

    Open Extensions preferences in System Preferences. That is if you mean Yosemite extensions. Otherwise, use any uninstaller provided by the developer or read the following:
    Uninstalling Software: The Basics
    Most OS X applications are completely self-contained "packages" that can be uninstalled by simply dragging the application to the Trash.  Applications may create preference files that are stored in the /Home/Library/Preferences/ folder.  Although they do nothing once you delete the associated application, they do take up some disk space.  If you want you can look for them in the above location and delete them, too.
    Some applications may install an uninstaller program that can be used to remove the application.  In some cases the uninstaller may be part of the application's installer, and is invoked by clicking on a Customize button that will appear during the install process.
    Some applications may install components in the /Home/Library/Applications Support/ folder.  You can also check there to see if the application has created a folder.  You can also delete the folder that's in the Applications Support folder.  Again, they don't do anything but take up disk space once the application is trashed.
    Some applications may install a startupitem or a Log In item.  Startupitems are usually installed in the /Library/StartupItems/ folder and less often in the /Home/Library/StartupItems/ folder.  Log In Items are set in the Accounts preferences.  Open System Preferences, click on the Accounts icon, then click on the LogIn Items tab.  Locate the item in the list for the application you want to remove and click on the "-" button to delete it from the list.
    Some software use startup daemons or agents that are a new feature of the OS.  Look for them in /Library/LaunchAgents/ and /Library/LaunchDaemons/ or in /Home/Library/LaunchAgents/.
    If an application installs any other files the best way to track them down is to do a Finder search using the application name or the developer name as the search term.  Unfortunately Spotlight will not look in certain folders by default.  You can modify Spotlight's behavior or use a third-party search utility, EasyFind, instead.
    Some applications install a receipt in the /Library/Receipts/ folder.  Usually with the same name as the program or the developer.  The item generally has a ".pkg" extension.  Be sure you also delete this item as some programs use it to determine if it's already installed.
    There are many utilities that can uninstall applications.  Here is a selection:
        1. AppZapper
        2. AppDelete
        3. Automaton
        4. Hazel
        5. AppCleaner
        6. CleanApp
        7. iTrash
        8. Amnesia
        9. Uninstaller
      10. Spring Cleaning
    For more information visit The XLab FAQs and read the FAQ on removing software.

  • How do i copy stickies from one mac to the other

    how do i copy stickies from one mac to the other?
    or are they stored in a file i can just copy them over ? if so what is the file name path?
    thanks in advance

    yes, they are stored in the file /users/username/library/StickiesDatabase. just copy it over to the corresponding location on the new computer.

  • How to print double sided from my Mac to my Canon MG6350

    I have looked up everywhere on the internet and youtube of how to print double sided from my Mac Book Pro. I am using OSX 10.8.5.
    All of the dicussions I have looked up before have told me to go to System Preferences>Print & Scan>Options & Supplies> Driver and then tick the little box that comes up and it will allow you to print double sided. I have tried doing this but THERE IS NO DRIVER TAB!!!
    I was just wondering if there was a solution to this as I can print double sided from my other appliences, like the PC and iPad, it is just my Mac Book Pro that doesn't work.
    It has become a big problem for me as I'm studying at college and I need to print things double sided quite regularly. I really need this to work.

    The print dialog has several drop-down menus, one of which initially shows the name of the application you're printing from. If the printer supports duplex, you can choose
    Duplex Printing & Margin
    from that menu. You should then see a checkbox marked
    Automatic Duplex Printing

  • How can i put photos from my mac to my ipad touch

    How can i put photos from my mac to my ipad touch
    I have them in an album.
    Thanks for your help

    See:
    iOS and iPod: Syncing photos using iTunes

  • How do I get songs from one Mac to another?

    How do I get songs from one Mac to another?

    iTunes for Mac: How to copy purchases between authorized computers
    Regards.

  • HT201250 how can i pass information from one mac to another mac by using the time capsule

    how can i pass information from one mac to another mac by using the time capsule

    If you want to transfer files, settings, etc., you must open Migration Assistant (Applications > Utilities) in the Mac that you want to transfer the files and follow the instructions

  • How can I transfer files from my mac to my iPad, e.g., mp4 files.  Do I have to use iTunes?

    How can I transfer files from my mac to my iPad in an easier way?  I'd like to put some movies on, and I can use iTunes, but is there another way?  I have transferred epub books using Dropbox.  Movies eat up a lot of dropbox space and the iPad has trouble getting them.

    USB disk. You still have to go through iTunes.
    Connect device to computer/mac
    Select your device in iTunes menu.
    Apps...
    At thebottom of the page you will see the app.
    Select it and the Add for windows and + for mac
    Hope that helped.
    In the long run there is no way to access or uplood data on your device without iTunes unless you JailBrake....

Maybe you are looking for

  • Can I use my plugins I bought at the Digi store in LE 8?

    I'm leaving ProTools LE 7.4 for LE 8. Tired of the Digi hassle and problems with the mBox and my iMac. I have a bunch of plugins that I bought from the Digi store including Sans Amp, and some Joe Meek and Bomb Factory stuff which I like, but don't us

  • New Schema

    Hi All I Need to create a new schema in a existing database. i need to create a tablespace of 10 GB with a user assocaited to that. Can anyone let me know about this and how to create a new schema. I tried creating a New user - and in that associate

  • How can we get an image of selected area of the front panel

    i am plotting some graphs and want a group photo of all those in one shot is it possible???? n i want to get the graph coordinates on the mouse click..... i.e when i click on the graph at any place the values corresponding to it must be retrieved. ho

  • What means ?=

    Hello, what means ?= e.g. DATA: r_desc TYPE REF TO cl_abap_structdescr,   r_desc ?= cl_abap_structdescr=>describe_by_data( ls_strc ). Regards sas

  • [svn:fx-trunk] 10872: Most changes already approved by PARB and a few are pending.

    Revision: 10872 Author:   [email protected] Date:     2009-10-05 12:39:47 -0700 (Mon, 05 Oct 2009) Log Message: Most changes already approved by PARB and a few are pending.  Given the two reviewers are at MAX and then there is a shutdown week we dec