HT3275 I keep getting a message that says, The backup disk image "/Volumes/Data-1/iMac.sparsebundle" could not be created (error 60).
I keep getting a message when trying to back up my main computer = 'The backup disk image “/Volumes/Data-1/CMN iMac.sparsebundle” could not be created (error 60).'
The error message changes sometimes to other numbers but it is not able to back anything up. I have deleted any previous back ups and rechosen the destination disk (Time Capsule). My other computers are doing the same thing periodically but this is the most important back up that I need.
Any ideas anyone?
See #C9 in Time Machine expert Pondini's Time Machine---Troubleshooting
http://pondini.org/TM/Troubleshooting.html
Similar Messages
-
The Time Machine is not completing thte backup to my Time Capsule. I am receiving a message which reads "The backup disk image "/Volumes/Data/Mac Jet's iMAC.sparsebundle" is already in use." I cannot locate the source of the problem or what steps need to be taken to get the Time Capsule operating.
Hi, see if it shows here...
In Finder's Menu, select Go menu>Go to Folder, and go to "/volumes". (no quotes)
Volumes is where an alias to your hard drive ("/" at boot) is placed at startup, and where all the "mount points" for auxiliary drives are created for you to access them. This folder is normally hidden from view.
Drives with an extra 1 on the end have a side-effect of mounting a drive with the same name as the system already think exists. Try trashing the duplicates with a 1 or 2 if there are no real files in them, and reboot.
If it does contain data...
http://support.apple.com/kb/TS2474 -
I'm receiving this error message about my Time Capsule:
"The backup disk image '/Volumes/Data/my name's iMAC.sparesebundle" is already in use. The time capsule is not backing up any files.1. Open the Sharing preference pane and check that the computer name hasn't changed without your knowledge. For example, if the name was "X's iMac," it might now be "X's iMac (2)". In that case, restore the original name. You may have to click the lock icon in the lower left corner of the preference pane to unlock the settings. Test. If there's no improvement, or if the name had not been changed, continue.
2. If you're backing up to a Time Capsule, or an AirDisk attached to a 2013 or later model AirPort Extreme base station, restart it in either of the following ways:
☞ Disconnect and reconnect the power adapter.
☞ Select the device in the AirPort Utility application and then select
Base Station ▹ Restart
from the menu bar.
If AirPort Utility notifies you of a firmware update, install it. -
I get an error when trying to back up on my TC. Message says - The backup disk image “/Volumes/Data/Macintosh.sparsebundle” could not be accessed (error -1).
Any suggestionsSee here...
https://discussions.apple.com/message/20933934#20933934 -
My time machine will not back up. I get a Time Machine Error message that reads: "The backup disk image "/Volumes/Backup/(myname)'sMacBook Pro.sparsebundle" is already in use.
I have not been able to back up for two weeks, I think this occurred after an update to the operating system, but I am unsure.
How do I correct this problem?Have you tried restarting the computer? Also, see Time Machine Error from this pages sidebar under More Like This.
-
While backing up to Time Machine, I receive this message: time machine error says: The backup disk image “/Volumes/Data/Apple ’s iMac G5.sparsebundle” could not be accessed (error -1).
Welcome to Apple Support Communities
That message is caused by several reasons. Read the Pondini's site to fix the problem > http://pondini.org/TM/C17.html -
I have two Macs that won't back up to time capsule, says The backup disk image “/Volumes/Data/Douglas Chalmers’s iMac.sparsebundle” is already in use.
Please look over to the right of this page for the heading of More Like This.
There are multiple answers and solutions there. -
Hello,
its been few days i keep recieving a message saying:
TIME MACHINE COULDNT COMPLETE THE BACKUP TO TC.
The backup disk image “/Volumes/Data/Krzysztof’s MacBook Air.sparsebundle” is already in use.
what shall i do?Tell Apple.
Apple - Time Capsule - Feedback -
My Apple Time Capsule stopped backing up a few weeks ago and after upgrading to Mavericks on my IMac I keep getting the message:
The backup disk image “/Volumes/Data/karen’s iMac.sparsebundle” is already in use.
I have no idea what to do and am new to having a Mac -
Also a friend had orginally set my wifi up to be called "Karen's wifi" and it has also stopped connecting to the wi fi also so am using ethernet connect.
Can someone please give me an idiot's step by step guide please so my back will work again?
Thank youLocate the Time Capsule
Pull the power cord from the back of the Time Capsule
Count to ten
Plug the power cord back into the back of the Time Capsule
Wait a few minutes, then try another backup
If you are having WiFi connection problems, you should start another separate post for that issue. -
I constantly get the following error message: The backup disk image "/volumes/data/jameskehoe.sparsebundle" is already in use. This Time Machine/Time Capsul worked perfectly before I left on a four month trip. Upon returning to my domicle it will not backup and I get the mentioned error message. My wife's Mac Book Pro continues to backup normally but she did not accompany me on this trip so her computer has always remained in contact with the Time Machine. My computer is a MacBook running 10.7.5
Any help solving this problem and letting me once again backup my computer would be greatly appreciated.This question is asked several times every day.. it is a bug.
Look at the more like this column to the right..
Solution is pretty simple..
With the TC hard disk not running.. you can feel the vibration ..
pull out the power cord.. count to 10.. plug in the power cord.
If you still have the problem report back.. mostly 98% of cases that will fix it. -
My Time Machine has failed again with this message:
The backup disk image “/Volumes/Data/Shirley’s MacBook Pro.sparsebundle” is already in use.
How do I fix it?Pull the power cord from the back of the Time Capsule
Wait 60 seconds
Plug the power cord back in
This simple reset will fix this error 98% of the time. If you need more help, see this troubleshooting information:
The Backup disk image ... sparsebundle ... is already in use. -
This is the error message that comes up when my computer says that the time machine couldn't complete my backup. Does anyone know what this means?
Regards,
JbyrdksSee here...
The Backup disk image ... sparsebundle ... is already in use.
From Pondini’s excellent Information Here...
http://pondini.org/TM/Troubleshooting.htm -
I've been having the same problem that my Time Machine can't be back up to my iMac for last few months. It said," The backup disk image... sparsebundle" cannot be acessed -(error 1) . When i looked into my TC, it does connected to my iMac; but not in devices and when i clicked into imac.sparsebundle and it is no mounted file system.
I tried several changes such as new password, new device names, checked Keychain Acess, repaired the disk, got a latest air utilily... But it still couldn't help alot. my iMac software now is OSX Mountain Lion 10.8.4. However, it having the problem since i update the software... I'm not sure if it related but i'm clueless now!!!
I need help for this annoying issue!!Welcome to Apple Support Communities
That message is caused by several reasons. Read the Pondini's site to fix the problem > http://pondini.org/TM/C17.html -
I got this message when I wanted to back up on my Time Capsule. What can I do to solve the problem?
Thanks.Pull the power cord from the back of the TC
Wait a minute
Plug the power cord back into the back of the TC
Report on your results -
What does that mean and how do I correct it so it will back up?
Restart your MacBook and your Time Capsule (or disconnect your Time Machine external drive). Finally, you will be able to make backups of your files again.
If you have got a Time Capsule, Apple released a firmware update that fixes this issue. Open AirPort Utility (in /Applications/Utilities) and follow the steps. See > http://pondini.org/TM/C12.html
Maybe you are looking for
-
Short dump with error :TSV_TNEW_INDEX_NO_ROLL_MEMORY
This is the error that i'm getting ABAP runtime errors TSV_TNEW_INDEX_NO_ROLL_MEMORY Occurred on 29.01.2007 at 20:27:13 >> Short dump has not been completely stored. It is too big. No roll storage of length 64094208 available for intern
-
I've added a second monitor to my system, to drag some of the proerties boxes out of the way. The boxes will go about half-way onto the second screen then stop. Is there a setting/switch somewhere to allow me to take advantage of both screens while I
-
Flagged folder in email show numbers no content
I upgraded to mavericks and now have my flagged folder in email shows the number 121-- these are listed under different colored flags but there appears to be no content. How do I get rid of this irritating number?
-
Hi all! I'm trying to understand the basic concepts of EJB. Starting with Session Beans I read that all these beans must implement a default constructor, for instance: public class HelloBean implements SessionBean public HelloBean(){} ....And I read
-
i have a requirement to enable the scroll bar in a BDC session. FI Documents have been created from IDOCs and if we goto fb03 then i can see the with holding tax lines with scroll bar whenever there are WHT lines more than 4. when i try to modify the