HT3500 I am using Mac 10.4.11 and I am having a problem when my printer wont print what I tell it too. Please Help
I am using Mac 10.4.11 and I am having a problem when my printer wont print what I tell it too. Please Help!
A warm welcome to Apple discussions!
A 2003 iMac cannot support Snow Leopard 10.6; you'd need an Intel processor and that cannot be retrofitted to your Mac. What does "About this Mac" in your Apple menu say for your processor speed? What does it say about how much RAM you have?
If the processor is 1ghz or faster, you can run OS 10.5; otherwise, you are maxed out at 10.4.11.
Also, are you running any commercial ("pay for") anti-virus or security software? They are notorious for slowing most Macs to a fraction of their speed potential.
A too-full hard drive can drag down performance, especially if you don't have a lot of physical RAM installed. If you single-click your hard drive icon and then do command i, you'll see the disk usage. Looks like this:
The value for "Used" should be no more than about 90 percent of "Capacity." In the example image, that drive has about 34 percent of its space used and 66 percent free--more than enough. Please post what you see for your Capacity and Used numbers
There are a few more things we might check but this is a good start.
Awaiting your information,
Allan
Similar Messages
-
Hello I am using Ipad 4 and its charger is not working while I was using it few days before and it was working properly now it says that the cable does not support this Ipad Please Help me out.
Try a reset:
- Hold the home button and sleep/wake button down at the same time. When the Apple logo appears release both buttons then try and charge again.
If issue persists try:
- Another known working cable
- Check the charging port for any damage or debris
- You could also use a dry soft bristle toothbrush and gently brush it on the port to clean it of any debris that could be in there -
Hello, I'm using a PAP2T and I'm having a problem when I...
Hello, I'm using a PAP2T and I'm having a problem when I dial into a menue, I can dial perfeclty but when I dial into a menu my phone will not send the digits pressed. In other words press 1 for so and 2 for so, I can press either and nothing happens. Recently I rebooted my PAP2T and since then I can't figure out what the problem is. Can anyone help. Thanks.
Maybe this has the fix for your problem:
http://forums.linksys.com/linksys/board/message?board.id=VoIP_Adapters&message.id=440&query.id=157098#M440
Anyway if it doesn’t, just try to search this forum with something like DTMF. -
Since dowloading Mavericks last week my Mac is very slow. Anyone else having this problem? any suggestions as to what to do to speed things up?
It will help people help you better if you post your iMac variant and Mac OSX version. Please do "About this Mac" from your Apple menu and, in the resulting window, click the "More Info" button. That will give this window:
The model is in the line I've indicated with the red arrow. Please also post the results for "Memory" and "Processor."
DO NOT post the serial number, however. -
Not rally a question, just wanted to share my absolute frustration with the update of iTunes...this is, without a shadow of a doubt THE WORST application i have EVER used, Mac or PC! And that's saying something with the amount of PC dross that's out there...Apple...PLEASE update and give us back the old version of iTunes...
Pull down View > Show Sidebar. This will give you back the same functionality of iTunes 10.x.x.
-
i m using apple mac pc, when we start windows 7 , apple mouse doesn't work properly it take to much time to gain signals from the pc and many times it not work but when we use mac it moves fastly and works properly. please suggest me.
thanks
ravi
<Email removed by Host>sounds more like Bluetooth rather than moue, but w/o knowing w/o posting mac model type/year we... will... not... know... what you have
All computers are personal computers, a PC though is also "non-Apple" in common usage.
Mac also is platform and OS.
Very confused reading what you are trying to tell us. -
I use MAC OS 10.9 and accidently uninstalled photoshop elements 9. How do I reinstall this?
I use MAC OS 10.9 and accidently uninstalled photoshop elements 9. How do I reinstall this?
I did the "uninstall"
Sent from my iPad -
I deleted/uninstalled iMessage on my Mac (using iTuneUp) but now I want it back. How can I do that? I have OS X Yosemite. Please help.
Hello ac4320a,
Thanks for using Apple Support Communities.
To reinstall any application which came with your Mac, you will need to reinstall OS X.
OS X Yosemite: Reinstall OS X
Have a good one,
Alex H. -
Hi. I forgot my passcode and now I am unable to unlock my ipod. I tried restoring it using itunes in recovery mode as well as dfu mode but it says unable to restore,unknown error occured (3004). Please help me out. My ipod is locked for one hour now.
Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
1. iOS- Forgotten passcode or device disabled after entering wrong passcode
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. Restoring iPod touch after forgotten passcode
4. What to Do If You've Forgotten Your iPhone's Passcode
5. iOS- Understanding passcodes
6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
Forgotten Restrictions Passcode Help
You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
Also, see iTunes- Restoring iOS software. -
I use Outlook for my email, and about 90% of the time when I want to attach a pdf or jpg file it failes and andout 50% of the time when I'm trying to send a standered text email I also failes and the email masage crashs. The only way I can get my Outlook to work is if I switch to Firefox. I would rater not have to swich all my bookmarks over to Firefox.
Has any one eals had this problem?That's an Outlook issue. You'll probably get better responses posting on the Office for Mac forums.
-
My MAC is running slowly and I am having to continually remove unwanted pop ups and leave unwanted pages which appear including MACkeeper. If I am on a sports website, betting pages appear - any ideas?
Click here and follow the instructions, or if there’s a type of adware not covered by them on the computer, these ones. If you're willing to use a tool to remove it(you don't need to, but may find it easier), you can instead run Adware Medic; this link is a direct download.
(120718) -
I'm trying to buy a video and I keep getting a message that says, "This Apple ID cannot be used for the iTunes Store." Anyone else having this problem? I just bought a movie last night without any problem.
I am having the same problem. You are only able to purchased when you first open Itunes after the first purchase the password and login details are no longer accepted by the itunes store. This has only happened after I installed the latest Itunes (11.03 (42)) so I assume that it is a bug in the software that that corrupted something on my mac.
On the bright side it means I do not give apple money -
Apparently you can have 5 computers registered for iTunes. I have 3 active computers but I guess I have other computers that are still activated that I no longer use and I no longer have as they crashed. Is there a way to delete or see what the other computers are so that I can go in and delete them? I've tried to email Apple directly but apparently I need my hardware # and obviously I do not have that # since I don't have the equipment any longer. Any help is greatly appreicated. I am trying to add another computer and it won't allow me to as they say I'm at my limit. Please help!
Sure.
Just open up iTunes on your computer -> Go to the iTunes Store -> Click your e- maill address (top right corner of the window) -> Type in your password for your Apple ID -> Under Computer Authorisations (underneath your Apple ID account balance and address) -> Press 'Deauthorise All'
-> This will deauthorise all computers and devices from your iTunes account -> you then need to re- authorise any computers/ devices you would like to use with your Apple ID for iTunes content -> to do this, select the Store tab along the menu at the top (where 'File', 'Edit', 'View' etc..... are) -> Then click 'Authorise this Computer' -> Type in your Apple ID -> Voila!
For any iOS devices (non- computers) you wish to re- authorise, these will automatically do so when you go to play iTunes content, download an app or anything like that on those devices!
Hope this helps! -
I am having a problem when I plug my iPod into my macbook. When I plug the cable into my mac I get the following message - "Because a USB device was drawing too much power from your computer, your USB device has been disabled." CAN SOMEONE PLEASE HELP!
The rest of the message in the pop up window says "To prevent damaging your computer, the USB device drawing too much power has been disabled. Other devices may have also been disabled. When you disconnect the device drawing too much power, your other USB devices will be enabled again."
-
My iTunes library will no longer sync to my iPhone or iPad, nor will it play from my Mac. My Library is on my external HD. iTunes is correctly looking to the HD as its library. Please help...
Guys, I found another user and what he said to do worked!!! I have copied the information below:
This was 1 of the things that happend to me too, the other one was that at the bottom of the itunes page were it says all the memory info, it marked that I had over 3gb of other memory wich I didn't.
Anyways what I did was to unmark the calendar, contacts etc. ( so that they wont sync with the computer ), pressed apply, then I marked all of them again, apply again and for last I pressed Sync wich is at the bottom right coner by the apply botton.
I'm not sure that had anything to do with it but it worked, my music appeard both of my itunes playlists and the ones I bought in itunes. Also the other memory dissapeard and it's all good.
I'm not sure this will help you but thats my 5 cents, if the problem continues its better to call customer service and ask for a technician.
Hope your problem gets solved. Have a nice day.
Maybe you are looking for
-
Creation of xml file in r3 application server (AL11)
Hi All I need to create xml file in r3 application server (AL11) using PI.Can we achieve this using file adapter or we need to proceed with proxy. As I tried with file adapter with FTP transport protocol. Its giving the error as "Unable to create new
-
Iphone 4 won't show up in itunes. what do i do?!
I just got my iphone 4 today in the mail and i connected it fine the first time to my computer but somehow it disconnected and now it won't reconnect. I have restarted the phone and my computer multilple times. I also switched usb ports and did the t
-
How to build a executeable shared variable engine (DSC 8.0)
Hello! At first a short overview about the actual data-flow at my system: there are several Fielpoints and a Diagnostic-PC which also produces data. All measurement data should be logged at a server. Therefore in Labview 7.1 i used the Tag-Engine and
-
MI424WR (Rev. E) Power Adapter
Hey everyone. I recently got a Rev. E router to replace my slowly failing Rev. D. The only issue is I don't have a power adapter for the Rev. E. It requires a 10V, 1.6A power adapter. Does anyone know where I can get an adapter (do Verizon or Actiont
-
Archive and reinstall - now all photos gone
I needed to reinstall a new OS on my eMac and so did an archive and reinstall. I did not select keep user settings and now have lost all my photos. Is there anything I can do about this?