HT3500 To add a wireless adapter to my Airport Extreme network using WPS, documentation recommends adding it under "Add wireless clients" in Airport Utility but there's no such an item anywhere in v6

I am trying to connect an Iogear Wifi adapter from my home entertainment center to my Airport Extreme home network (secured with personal WPA) using WPS. Apple's support literature says to do this through Airport Utility (v.6) choosing Manual Setup from Base Station Menu and Add Wireless Client. After hours of searching and fiddling I cannot find "Manual setup" or "Add Wireless Client" in the Airport Utility (v.6). HELP.  andy

Those instructions are for Airport Utility v5.5.3 or v5.6. As a matter of fact, Airport Utility 6.0 does NOT have that options. So assuming you have Mac OS X Lion 10.7.4, you have to download and install Airport Utility 5.6 for Mac OS X Lion. Then follow those simple instructions you have.

Similar Messages

  • New to wireless Cant get airport express to join airport extreme network

    So... I just got this MBP yesterday along with airport extreme and airport express. I got the base station set up i just cant get the express to connect for the life of me... help anybody? Everything is in range i know that for a fact. I just cant get it configured and i already looked on the airport express support page and followed the instructions and i still can't get it. :-/

    Factory reset your Airport Express (AX).
    Resetting AirPort Express
    http://docs.info.apple.com/article.html?artnum=108044
    Connect to the Airport Extreme Network
    Use the Airport Assistant to configure a new base station and configure the AX to join an existing wireless network (either use client mode, only extend your network if you need to do so).
    iFelix

  • I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

    I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.  Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

    I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
    Excellent plan.
    Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
    Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
    This Apple support document will show you how to hookup and configure the second AirPort Extreme:
    http://support.apple.com/kb/HT4260

  • Adding a non-wireless PC to an Airport Extreme network with WDS, or extend

    I have an Airport Extreme base station (802.11n), a Time Capsule, and a cable modem. Currently the Time Capsule is wired by WAN to my cable modem. It is broadcasing a wireless network to my iMac Intel Core2Duo running 10.5.2 and my AppleTV, and my MacBook Pro running 10.4.11. I'd just acquired a Windows XP PC with no WiFi card but a built-in NIC card. I'm having difficulty adding the Airport Extreme base station to the network of the Time Capsule, so the non-wireless PC can use the LAN port of the Airport Extreme and pickup an internet connection. I don't want anything connected to the WAN port of the Airport Extreme. The PC can't be moved to the room with the cable modem. Should I:
    1. Set it up from the Airport Utility of my iMac or MacBook Pro?
    2. Switch the placement of the Airport Extreme and Time Capsule?
    3. What steps should I take from Airport Utility, to add a reset Airport Extreme or Time Capsule to the network already tied to my Cable modem?

    Since both of your base stations are 802.11n, I suggest that you use the "extend a network" feature available to these, instead of creating a WDS.
    1. Set it up from the Airport Utility of my iMac or MacBook Pro?
    Your choice, you could use the AirPort Utility from either of these Macs to configure the base stations.
    2. Switch the placement of the Airport Extreme and Time Capsule?
    I'd suggest leaving the Time Capsule connected to the modem and use the AEBSn to extend its wireless network.
    3. What steps should I take from Airport Utility, to add a reset Airport Extreme or Time Capsule to the network already tied to my Cable modem?
    Here are the basic steps to configure the extended network:
    o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations. You may also want to temporarily connect the AEBSn directly to one of the TC's LAN ports during setup.
    o Open AirPort Utility and select the TC.
    o Choose Manual Setup from the Base Station menu.
    o Click AirPort in the toolbar, and then click Wireless.
    o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
    o Next, select the AEBSn, and again choose Manual Setup from the Base Station menu.
    o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the TC's wireless network from the Network Name pop-up menu.
    o Click Update to update the base station with new network settings.
    o Upon completion of the setup, you can now relocate the AEBSn to its desired location.
    (ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

  • PROBLEM: Trying 2 add an AIRPORT EXPRESS to an already existing AIRPORT EXTREME network

    I'm trying 2 add an AIRPORT EXPRESS to an already existing AIRPORT EXTREME network in my home.
    I see the EXPRESS in ARPT UTILITY but when I click on "CONTINUE" or "MANUAL", the only option I'm given is to SWITCH networks, which I do not want to do.
    I am using a MACBOOK PRO (MAC OS X 10.6.8)
    Can someone offer me help with this?
    Thanks!

    Hi, I have a similiar setup.  When you click onto the express, and it asks you to switch networks, it's not actually asking you to "change" networks.  It's just actually switching to the xpress.  When the xpress comes up, you'll input the name of your existing network, which you set up and named for the extreme.  You'll have to change the extreme to "participate in a network", which is what you'll also do for the xpress.  In the extreme under the WDS tab, you'll input the wds mode as "wds main".  And then put a check mark in the "allow wireless clients".  Where it says wds remotes, you'll input the the airport id's for the xpress's.  In each of the xpress's, you'll set up as participating in a wds network.  In the xpress's, under the wds tab, you'll set the wds mode to remote, and check
    mark in the allow wireless clients.  You'll have to input the airport id of the extreme in the wds main block.  Under the internet icon on top, in internet conect tab for connect using: airport (wds), connect sharing: off (bridge mode).
    Remember to insure that the express's show the same channel as the extreme, if you're using 802.11n (80211b/g compatible).  Of course the security that you decide to use should also be the same.

  • How to connect old aiport express to my new Airport Extreme? My Ipad says "base station e5713b cannot be configured" and my AirPort tool on my PC will not permit me to add my new Airport Extreme network (no network names to choose from)

    How to connect old aiport express to my new Airport Extreme?
    I have a PC running with Win7 and just replaced my Jensen With a brand New Airport Extreme.
    I have set up the Airport Extreme to the internet, Iphones and Ipads and it work as it should.
    I have downloaded latest Version of Airport tool on my PC. In addition i have downloaded the airport tool for Ipad.
    I have reset one of my airport Express and it now shows up both on the Ipad and on the PC airport tool.
    My Ipad says "base station e5713b cannot be configured."
    I have wired the airport Express to my Ethernet to be able to "see it" on my Airport tool.
    My AirPort tool on the PC will not permit me to add the airport Express to my new Airport Extreme network (no network names on the drop-down list to choose from). I wished for an easy set-up, but nothing seems to be plug and play as the Commercial says.. can you please help me?
    Sigve

    Hi
    Thanks for Swift reply.
    Yep - I in fact have two A1088 and one A1264
    I actually bought the new router because the Jensen
    router always lost connection to the Airport Express after some hours or days. I
    always needed to restart my Jensen to play music and that was driving my wife
    mad. The hope was that the Extreme should fix this. Both A1088 have been set up
    to only stream music to two of my stereo amplifiers from my PC’s Itunes library.
    Are the A1088 now useless?
    The A1264 has been set up to feed internet into a Denon Reciever that needed Ethernet cable.
    Please advise
    Regards
    Sigve

  • HT4259 How do I set up an Airport Extreme Base Station (v. 7.6.1) to allow wireless network extension?

    I have an Airport Extreme Base station (purchased in 2009) and an Airport Express base station (purchased in 2011 - the model that plugs directly into the electrical outlet) (both version 7.6.1 according to the Airport Utility info).  I want to use the Airport Express to extend my wireless network.  Using Airport utility setup I have a software option on the Airport Express to set it up to extend the network but I do not have an option on the Airport Extreme wireless setup screen that I can check to allow my wireless network to be extended. 
    All of the documentation I can find on Apple Support states that I should have an option I can check to allow the wireless network to be extended while in the wireles setup section for the Airport Extreme in Airport Utility; but, that check option isn't there.  Is this a case of my Airport Extreme base station being too old to offer that option?  Incidentally, when I try to select the extend wireless network option on the Airport Express from the Airport Utility wireless setup menu I get an error message (no details - just an error message).  The same Airport Express sets up fine if I select join a network (not what I want to do).  Am I just dealing with outdated equipment or does anyone have a suggestion?  Thanks.

    Close AirPort Utility if it is open.
    Temporarily, move the Express to the same general area as your AirPort Extreme and power it up and wait a minute.
    Hold in the reset button on the Express for 9-10 seconds and then release. Give the Express a full minute to restart to a slow, blinking amber light.
    Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear
    Click on AirPort Express just below that and AirPort Utility will automatically open
    Wait a minute while AirPort Utility analyzes the network and announces that the Express will be configured to "Extend" the AirPort Extreme network.
    Enter a device name for the AirPort Express and click Next
    Wait another minute to allow the configuration to occur.
    When you see the Setup Complete message, click Done.
    Now move the Express to a location that is approximately half the distance from the AirPort Extreme and the general area that needs more wireless coverage
    Power up the Express and you are all set.  Trash those old instructions.

  • I have a pc running windows 7.  I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport.  The wireless router works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

    I have a pc running windows 7.  I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport.  The Airport works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

    +For now I have it set to Share Public IP address - Is this correct for my Network Setup with The Airport Extreme being the only router being used ?+
    This would be the correct setting if the AirPort Extreme is connected to a simple modem (one ethernet port).
    *Settings I have Enabled*
    5 GHz name indicates that you have elected to use the option to assign a separate name to the 5 GHz network. This will allow you to "tell" compatible computers to connect to that network, rather than the slower 2.4 GHz network
    Use Wide Channels is recommended for 5 GHz operation.
    Interference Robustness often does more harm than good and should not be used unless you know you are in a area with a lot of wireless networks and you feel that your network is experiencing interference issues from a nearby network.

  • I just purchased the airport Express to use in hotels while traveling to create a wireless network from the hotels wired dsl.  A friend said to set up the network from home prior to traveling.  How do I set this up?  Thanks.

    I just purchased the airport Express to use in hotels while traveling to create a wireless network from the hotels wired dsl.  A friend said to set up the network from home prior to traveling.  How do I set this up?  Thanks.

    In addition to RyanJC's comments, the 802.11n AirPort Express Base Station (AXn) can store up to five different http://docs.info.apple.com/article.html?artnum=108081 configuration profiles. You will need to use the AirPort Utility to create & save these profiles.
    To create a new profile:
    Open AirPort Utility, select your AX from the list, and then, click "Manual Setup."
    From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
    Click "+" to create a new profile; give it a name, and then, click OK.
    Set options, such as network name, passwords, Internet connection method, etc.
    When done setting the options, click Update.
    To switch profiles:
    Open the AirPort Utility, select your AX from the list, and then, click "Manual Setup."
    From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
    Click on the desired profile, and then, click OK to apply the new profile and restart the AX.
    Just remember to switch to the desired configuration profile before removing power from the AX.

  • Can you guide me step by step in setting up airport express as a wireless extender for an existing Airport extreme network

    Can you guide me step by step in setting up airport express 802.11 as a wireless extender for an existing airport extreme network?

    Also check out:
    Re: Need Help Networking AirPort Exp to Existing AirPort Extreme
    Re: How to connect AirPort Express to existing AirPort Extreme Network...

  • Cannot add Airport Express to Airport Extreme network

    I keep getting the message "There was an error setting up this Apple wireless device for WDS. Quit Airport Utility and try again." So I've tried a few times with different reset/reboot/configuration changes all to end up with the same message at the end. This problem seems to almost exactly coincide with my update to 10.5.8. At least the Extreme is finally playing nice after I restored it to the factory settings and updated it to v.5.7. This is really frustrating since I pipe my music downstairs through this Express and feed the TiVo.

    I'm trying to do the same thing - extend my wireless network from my Airport Extreme to 2 more Airport Expresses. I don't have a solution yet but hopefully between us both and the help of others we can get it.
    First thing I realized - I needed to go to settings on Airport Extreme and in the 'Wireless' tab check 'Allow this network to be extended'.
    Instead of WDS, I plugged in the new Express and in the 'Wireless' tab chose 'Extend my wireless network' and then chose my Airport Extreme network. Still not there, as for some reason Airport Utility no longer picks up the extremes even though I've got them plugged in right here. Perhaps a reboot after this post and we'll see what happens.
    One question to all - does it matter if any/all of these wireless base stations have encryption set to WPA or WEP? Would it affect the Extreme's ability to connect to the Express'?

  • Is it neccessary to buy an AirPort Express or AirPort Extreme for my macbook pro to connect WI FI or wireless?

    so I have a macbook pro, but i don't know whether i need to buy an AirPort Express or AirPort Extreme to connect to WI FI or wireless.   or i only need to modem??
    HELP!!! :'(

    Airport Extreme is used by Apple for its wireless routers and the hardware inside your MacBook Pro that is used to connect to a wired or wireless router. http://en.wikipedia.org/wiki/AirPort_Extreme#AirPort_Extreme_Base_Station
    While Apple would like you to buy everything from them you can use any brand that will work with Macs. My setup is a Qwest DSL modem connected to a NetGear wireless router. The Airport Extreme card inside my MacBook recognizes them without any problems

  • I cannot add a Wi-Fi guest network. Gone to Utilities Airport Utilities and all get is an image/browser of my Airport Extreme. Looking for the browser which has the title Wireless but cannot find anywhere. I need help?

    I cannot add a Wi-Fi guest network. Gone to Utilities>Airport Utilities and all I get is an image/browser of my Airport Extreme. Looking for the browser window which has the title Wireless but cannot find anywhere. What am I doing wrong?

    Open AirPort Utility. The first screen looks something like this:
    Click on the AirPort Extreme and another screen will appear. Click Edit, then the window with the Wireless tab will appear.
    If you do not see these screens, you will need to start over and configure your AirPort again.

  • Wireless adapter not showing any available networks

    I've recently discovered that my Intel Centrino Advanced-N 6235 wireless adapter in my Asus Zenbook UX32VD running Windows 7 64 bit is not working as it won't show any available networks while my phone can find plenty in the same area. 
    So far I've:
    -Re-installed the driver. Before I did this the adapter wouldn't even show when trying to change adapter settings. When I looked at the adapter in device manager I found an error code 52 which disappeared after I re-installed the driver.
    -Re-installed the client for windows networks installed for the adapter which did not make a difference.
    -Temporarily turned off my AVG-free anti-virus which did not make a difference. 
    When looking at the adapter after clicking change adapter settings in the networks and sharing center it says it's not connected, but as stated above it doesn't show any networks to connect to.
    Also, when I try to use the networks diagnostics tool I get the following error message:
    Windows cannot find
    '::{26EE0668-A00A-44D7-9371-BEB06...\resultPage?keywords=+Network;NetworkDiagnostics'.
    Make sure you typed the name correctly, and the try again.
    Any possibly solutions I've not already tried are welcome. Thanks in advance for any help.

    Hi,
    Locate to Services and check all services relating to wireless and network are enabled: Wireless Zero Configuration and WLAN AutoConfig, etc.
    Also, make sure your NIC is working correctly from device manager.
    http://kb.linksys.com/Linksys/GetArticle.aspx?docid=108496d0924847afaf9c4a7bb72110b5_5646.xml&pid=80&converted=0
    Have you tried manually connecting to wireless?
    http://kb.linksys.com/Linksys/GetArticle.aspx?docid=8fd9ee85a0bf42f0986ed23390be8c66_19850.xml
    Andy Altmann
    TechNet Community Support

  • How can i sync ipad1/iphone4 with itunes wirelessly using airport extreme network

    how can i sync ipad1/iphone4 with itunes wirelessly using airport extreme network

    Hi,
    This is currently not supported by iOS for any devices. Rumour is that iOS 5 will finally add this function, until then I'm afraid you are stuck with the good old cable.
    Jamie

Maybe you are looking for

  • How do I preview songs within iTunes list of songs on my iPod Shuffle?

    I want to hear what songs are on my iPod shuffle with their listed title , so I know what to keep and what to delete. Because, when you know you want to delete some songs, but do not remember all the titles.

  • FM to convert XString to String

    I am developing an simple application to upload an excel file and display its contents in a table in Solution manager using Web dynpro. But 'HR_KR_XSTRING_TO_STRING' is not avaiable in DS1. Can you help me find a replacement for this function module.

  • My iphone won't connect into itunes

    So when i use a usb cord to connect my phone to my toshiba windows laptop the message asking to trust the computer keeps popping up on my phone. When i hit trust things go slightly back to normal, where my phone opens up the photo app on my computer

  • Unable to access EJB in J2EE 1.4 RI

    Hello, I am trying to connect to an EJB (in J2EE 1.4 RI) from a client using following code: Context init = new InitialContext(); Object ref = init.lookup("java:comp/env/ejb/EJBName"); It appear that client is not connecting to the naming (JNDI) serv

  • Flickering Title when exporting to any type Quicktime

    I've got a long video in FCP. I really will need it to be an MPEG2, but for right now I'm just trying to get a quicktime movie serviceable. One part of the video has a title card that flickers like crazy. It's like the white type becomes striped in b