HT3728 How can I get my airport express to show on my network ?

I did a hard reset on my airport express and now all it does is flash amber. I have thw airport utility open but it only shows my airport extreme.

I don't know what you mean by "hard reset."
I'm a great believer in the KISS principle.
Configuration is simple if you start from a factory default condition.  Then connect the Airport to AC power and finally to the Internet modem (or modem/router).  Open Airport Utility on your Mac or other computer and accept all of the recommendations.  After confirming that it works, insert your desired administrative and WiFi passwords.
Do not expect the Airport to respond instantly to the configuration commands.  BE PATIENT!

Similar Messages

  • How can I get the Airport Express to handle all the PPPoE stuff?

    Hi, I’m visiting my family in China, and now trying to help my dad, with his Airport Express and how to set up a PPPoE connection.
    We have currently set up the Airport Express in bridge mode (not distributing IP adresses and selecting DHCP under the Internet tab in admin utility). The Airport settings on our two computers is set up to connect using PPPoE using the given login name and password. (ps! we can not see the Base station in Airport Admin Utility when using these settings, we would have to select a new location from the Apple menu to see it and make condigurations.)
    What we want is to do, is to have the Airport Express connect to the ISP using a PPPoE connection and not through the computer.
    I know there is a 'Connect using PPPoE' option in Airport admin util, letting me input account name and password. If I select this setting instead of DHCP, enable distribution of IP addresses and configure my Airport card to NOT connect using PPPoE, I will see my base station in the Airport admin util with the IP address of 10.0.1.1 (or similar) and my computer will have x.x.x.2. Next to the Airport icon in the menubar, a scrolling message will say 'Looking for PPPoE host' without anything happen. I am sure my account name and password is correct as they've both worked when using this computer to connect to PPPoE (like now)
    How can I get the Airport Express to handle all the PPPoE stuff without using bridge mode?
    Ps! Both me and my dad have iPhones whom we can’t seem to get to connect unless its been distributed an IP address cause there's as fars as I know, no options of inputing a PPPoE user name and password.

    Any solutions to this? I'm in China also, in Beijing, trying to get my Airport Express to work with an ADSL modem.
    Direct ethernet cable connection to my Macbook works fine.
    When I configure the Airport Express with the ID and password that seems to be fine also – Airport Express shows a green light.
    But I cannot figure out the settings to connect wirelessly from my Macbook to the Airport Express. I get a constantly scolling message: "Looking for PPPoEhost..."
    thanks
    Paul

  • How can I use an Airport Express to join my wireless network and provide an internet signal to my Power Mac g5 via an ethernet cable?

    I have a power mac g5 that does not have a wireless card, and connects to the internet via ethernet cable.
    I want to know how to set up an airport express so that it joins my wireless home network and provides the G5 with an internet signal.
    This via an ethernet cable that is plugged  into the airport express and then into the ethernet port on the g5.
    Please advise as I have configured the airport express in every way possible, the green light is on and when I plug the ethernet cable into the G5 my network cofigurations shows nothing and says that the ethernet cable is not plugged in (It is).
    I get an internet signal if the ethernet cable is plugged directly into my wireless router, so the ethernet port works.
    Please assist. Thanks.

    Two requirements that must be met to do what you want.......
    1) An AirPort Express 802.11n must be used. Check the Model No on the label on the side of the Express. It needs to be A1264. Any other model number will not do what you want.
    2) The Express must be configured to "Join a wireless network" and the option to enable Ethernet Clients must be checked. 
    Open AirPort Utility and click Manual Setup
    Click the Wireless tab below the row of icons
    The box to "Allow Ethernet Clients" must be checked
    Please check to verify that your AirPort Express meets both requirements

  • Help!! can't get my airport express to connect to my network

    I have set up my airport express to connect to my network so I can play itunes with it but it says that the Airport has been set up but cannot connect To my network. I've tried it on both my computer and my wife's computer and we have the same problem. I have been able to connect in the past with my Airport express that I had for this one but for some reason I can't seem to connect it using this airport express. Any help would be much appreciated.

    When joining a non-Apple WEP encrypted wireless network with an AirPort, you must use one of two different styles for password entry depending on whether the network is protected with an ASCII or HEX key.
    ASCII password
    If using a password that is plain ASCII text, use the double quotation mark (") before and after the password. These are case-sensitive, and they are at least five characters long for 40-bit encrypted networks or at least 13 characters long for 128-bit encrypted networks.
    Hexadecimal password
    If using a password that uses only the hexadecimal range of characters, add a dollar sign ($) before the password. These passwords are at least 10 characters long for 40-bit encrypted networks or at least 26 characters long for 128-bit encrypted networks.

  • How can I get my airport express work with Zyxel 2812HNU-F1?

    Hi,
    I previously had a Thompson Speedtouch router and my Airport expres worked just fine. But now my internetprovider give me a new router the Zyxel 2812HNU-F1 and my airport express doesn't work properly. I use an ethernetkabel to connect the airport express with my router. The lamp on the aiport express turns green, but I cannot normally open internetpages etc, and sometimes a webpage partially appears. If I connect my ethernetkabel in my MBP, the internetconnection just works normally.
    Do you know what I have to do to let my Aiport expres work with the Zyxel 2812? I already resetted the express and in the airport utility it doesn't show that there is a problem.
    Greets,
    Don

    Obviously my objective was different (just use the Airport Express as an Airplay speaker over wired ethernet only), but for my case I finally managed to fix it: In the Zyxel LAN configuration I've set the LAN port (4) to half-duplex and 10Mbit (only!) instead of "auto" and then streaming audio works flawlessly! This is just crazy stupid and is a Zyxel issue I'm sure. For now I'm happy!
    To make the Airport wired only: disconnect wire -> factory reset -> create new (wireless) network (plus settings) -> then Network Router Mode = Off (Bridge Mode) -> then Disable wireless -> Save settings -> only then connect ethernet cable

  • Can,t get the airport express to see my wireless network

    like I said in the subject. I have Verizon Fios. and I have to use there router which is WEP. I have run the airport utility but still no Luck. Can anyone help?

    Copied this from another post hope it helps?
    Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your Verizon wireless router can be extended wirelessly with the AirPort Express Base Station (AX).

  • I just changed the channel on my Airport Extreme and now can't get the Airport Express to recognize the network.  What do?

    I changed the channel on Airport Extreme to get away from interference.  Now I can't get my airport express to recognize the network.  What do I do?

    I would suggest that you perform a "hard" reset on the AirPort Express Base Station (AX), and then, using the AirPort Utility, reconfigure it "join" or "extend" the AirPort Extreme as appropriate for your networking requirements.

  • I can't get my Airport Express model A1084 to connect to my Actiontec M1424WR modem/router.  Help?

    I can't get my Airport Express model A1084 to connect to my modem/router model Actiontec M1424WR. The Airport utility on my IMAC says it doesn't find any base stations.  Thelight on the Airport Express blinks amber only.   Any suggestions?

    The  8+ year old Express that you have will require a 5.x version of AirPort Utility to administer the product.
    Might you have an older Mac running Leopard (10.5.x), Snow Leopard (10.6.x) or a PC with AirPort Utility installed on the computer?

  • My new smart TV recognizes my network, & asks, "Please enter you WEP keys (10 or 26 hex digits)" but my netwotk uses a password of 6 characters. How can I get my smart TV to connect to my network?

    I have a current iMac with the latest OS update.
    My new smart TV recognizes my network, & asks, “Please enter your WEP keys (10 or 26 hex digits).  My  Airport Express, an early model, only requires a password of less than 10 characters.
    When I open “airport utility,”on my iMac it tells me this version doesn’t support my base station & says go to “Airport Service & Support.”  That’s what got me here.
    My earlier MacBook runs OS 10.6.8. Its version of  Airport Utility works. Its Airport ID has 17 characters, & uses the same password to access the internet, but it also has a “wireless password” of 26 characters, but only shows me the dots. i haven’t the foggiest notion  what the characters are, if I put them in there years ago when i did the original configuration, or if they got there otherwise..
    I’m afraid of changing those settings for fear that I’l mess up the whole thing.
    How can I get my smart TV to connect to my network, ?

    Please check out the following AirPort User Tip on how to recover AirPort passwords.

  • How can I get my RSS feeds to show up on my iOS devices from iCloud?

    How can I get my RSS feeds to show up on my iOS devices from iCloud?  The RSS feeds now show up just fine on my iMac. 
    On my iMac the appear in a category at the same level as In Box, Sent, etc.  However the term RSS is in lighter grey like Mailboxes, On My Mac, Reminders.  I use Snow Leopard 10.7.5.  Any help will be appreciated as I'd like to read the feeds on my iPad 2 and iPhone 5 when I'm away from home.
    Thank you.

    This is helpful, but how do you get both devices to communicate to this single calendar via the iCloud?...
    You did not mention that it must be through iCloud.  But then, it can't really do so if you want to maintain separate Apple IDs.
    So you just set up an additional calendar on your devices.
    iPads, iPhone, Macs can show multiple calendars simultaneously.  I have my work calendar and several personal calendars all showing simultaneously on my iPad, Mac Mini and Macbook Pro.   In the case of my client, they didn't need multiple calendars.  They just were going to use the one shared calendar.  But I did setup the shared Google calendar and separate personal caldendars on their iPhones.  (e.g.: Husband's iPhone = husband's personal Mac Cal + shared Google Calendar.  Wife's iPhone = wife's personal Outlook for Windows Cal + shared Google Calendar.)

  • How can you get a compilation album to show up as one album rather than be split up but song and artist?

    how can you get a compilation album to show up as one album rather than be split up by song and artist? I've got loads of albums on iTunes that are compliations and they are all mixed up by track/ artist. Even when you click 'show album' it still just shows the album title and then the artist in alphabetical order - so the album is replicated several times
    Can anyone tell me how to amalgamate compliation albums please?

    This web page will help you: http://samsoft.org.uk/iTunes/grouping.asp

  • I have made a burn folder with photos exported from I-photo.  It now shows in information, that the date is created and modified is different from the original digitized date.  How can I get the original date to show in the info from Finder?

    I have made a burn folder with photos exported from I-photo.  It now shows in information, that the date  created and modified is different from the original digitized date.  How can I get the original date to show in the info from Finder?

    The Finder reports File information. The date and time of the photo are in the Photo's Exif metadata. The Finder has no awareness of this. All photos apps on any system do.
    Regards
    TD

  • I have several pdfs on my iPad in iBooks. My iPhone shows only the categories, none of the documents. How can I get my iPhone to also show the documents that are on my iPad?

    I have several pdfs on my iPad in iBooks. My iPhone shows only the categories, none of the documents. How can I get my iPhone to also show the documents that are on my iPad?

    You will need to connect your iPad to your computer's iTunes and do File > Devices > Transfer Purchases to copy them over to your computer (that will copy PDFs and epubs that are in the iBooks app, not just actual ibooks), and you can then sync them to your iPhone. Or you might be able to open each PDF in iBooks on your iPad and use the share icon to email them to yourself and then use 'open in' in the Mail app on your iPhone to copy them to its iBooks app (if the PDF is protected then you may not get the email option via the share icon).
    The Settings > iBooks > Sync Collections setting doesn't copy items between devices, it just means that it a bookor PDF is on both devices and you move it into a collection on one device then it will be moved into the same collection on the other device

  • How can I get the direction handles to show up for the Position attribute?

    How can I get the direction handles to show up for the Position attribute?
    I have CS3 and I did the formentioned test and was able to make the handles work for the scale attribute but they don't seem to show when editing the position values.
    *I am in the graph editor looking at the "value graph"
    *I select the keys and convert the keys to auto bezier (I also tried the ease in and out buttons)
    *It changed the graph the way you might think (no longer linear) however the handles are not showing to edit further.
    *I also tried using the "convert vertex tool" (part of the pen tool) and still no luck getting those handles.
    *the handles only show up in the speed graph but that does me no good.
    Please help!
    THANKS 

    I don't have CS3 installed on any of my machines any more but your value graphs for position should look something like this:
    There are no handles for position in the Graph editor. You adjust the position curve by editing the motion path in the composition window. Press the G key to bring up the pen tool, then use the modifier keys Crtl/Cmnd and Alt/Option to temporarily switch between select and convert vertex to adjust the paths. Changes will be reflected in the value graphs. You will get editable handles with scale and rotation because these are not spatial properties. Spatial properties, position, Anchor Point, all XY & Z coordinates are edited in the comp window or in the layer window after revealing the properties. IOW, you edit anchor point position paths by opening up the layer window and choosing Anchor Point from the display options.
    The Manual isn't wrong. Here's a link to the live docs.

  • HT1386 i have noticed that the album artwork on itunes in my phone is missing when you open the "album" section of itunes installed on my phone. how can i get my album artwork to show up in the album section

    i have noticed that the album artwork on itunes installed on my phone is missing some of the album artwork when i go to the "album" section of itunes in my phone. How can i get the album artwork to show up

    first of all, no one is going to respond to this becuase limewire is used basically in your situation illegally. But let's say you import a cd, left click on the songs you imported and hit get album artwork, if nothing comes up, the album sn't in the itunes database, get it online. And I suggest never to mention limewire and music files on the same post here, since limewire is a file sharing program. Use Itunes, it's easier. theo

Maybe you are looking for

  • ORA-02149: Specified partition does not exist

    ORA-31693: Table data object "aaaa"."bbbbb":"P_2012112216" failed to load/unload and is being skipped due to error: ORA-02149: Specified partition does not exist SQL> select partition_name from dba_tab_partitions where table_name='DME_bbbbb_RES' and

  • Toshiba laptop with Atheros AR5008X won't connect to Linksys WRT350N

    Please excuse the level of detail, but I believe you need a reasonably complete picture if you are to understand the problem well enough to give a complete answer. SETUP & BACKGROUND I have three N-compliant devices and several G-compliant devices on

  • ISE WLC Integration issues

    We are in the process of integrating ISE into our WLC and are planning on implementing HReap (Flexconnect) local switching.  We have setup the ISE server as a Radius entry in the WLC and added WLC to ISE, same shared secret.  We have a test SSID conf

  • [JS/ID CC] finding properties of selection

    Hi, I'm looking for the equivalent of the AS get properties of selection for Javascript. A bit of background. I'm trying to learn JS and have no programming background except for Applescript which is not considered a "real" programing language. In AS

  • What is a domain in WLS

    Hi All, Im currently working on Oracle 10g AS, am starting to migrate to WLS. Can someone refer to some link or document that would have some concepts which are basics that are to be known to start with WLS. Thanks.