HT3819 iTunes won't stay running

I have recently installed an Apple TV. Home sharing is working fine except iTunes seems to close after a few hours of inactivity. I tried setting it to minimize to the system tray with no luck. I have to keep going to the computer to restart iTunes. Windows 7 iTunes 10.6.3

Iam also having the same problem, plus I have lost all sound from my player. My computer will play music through windows media etc and still has all system sounds its just itunes.
Is there any one from apple out there who can help?
P.C Windows XP

Similar Messages

My spooler won't stay running, I can't add printers.

My spooler won't stay running, I can't add printers.
Not able to figure out even after firewall on/off, network on/off and all setting to default...
Regards
Reddy

find some possibility solution for spooler wont start here
https://social.technet.microsoft.com/Forums/en-US/d875ab83-1b17-4a28-8738-e67249a2bdfd/cannot-print-after-update-to-81-printers-gone-print-spooler-keeps-stopping-cannot-add?forum=w8itprohardware
I recommended this step
1. do printer troubleshooting
http://windows.microsoft.com/en-us/windows/printer-problems-in-windows-help#fix-printer-problems=windows-8&v1h=win8tab3&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1
2. Uninstall antivirus using removal tools (Kapersky)
3. Registry trick as
JSB43211 suggested, backup your registry before perform this
1. Open Regedit as Administrator
2. Find the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environments\ key.
3. If you are on a 64-Bit machine, browse to the "Windows x64" sub-key (else "Windows NT x86")
4. Under the "Print Processors" sub-key DELETE ALL THE SUB-KEYS EXCEPT "winprint" key
5. Start the Print Spooler service.
6. Test to see if you can Add a printer.

My Itunes Won't Stay Minimized In Windows Vista

My Itunes won't stay minimized. I will minimize it and then it will pop back up, i don't know if this issue has been addressed before but its driving me insane. what do i do?
Message was edited by: stop-doogle-time

I have the same problem. This problem has shown up and gone away many times over the last couple of years. Its the main reason that I rarely use iTunes.
Have you found a solution? I'm tired of buying MP3s from iTunes and playing them in Windows Media Player

Itunes won't stay open.

I recently just updated my Macbook Pro (older version from 2010, 10.6.8), including Itunes. Now I tunes won't stay open. Whenever I click on the icon to start It flashes open but then closes immediately. I recently had my hard drive wiped because of a problem so if that could be a contributing factor I don't know. Itunes was working fine before the update.

I recently just updated my Macbook Pro (older version from 2010, 10.6.8), including Itunes. Now I tunes won't stay open. Whenever I click on the icon to start It flashes open but then closes immediately. I recently had my hard drive wiped because of a problem so if that could be a contributing factor I don't know. Itunes was working fine before the update.

ITunes won't stay authorized...

Not sure when this started but everytime now I open iTunes and try to play a song, watch a movie or listen to an audiobook, I get the "This computer is not authorized" message. I put in my username and password and then I get "You have authorized 3 out of 5 computers" and then everything will work. The problem is that iTunes will stay authorized until I reboot or start the computer, then open iTunes again. Sure enought, I get the same "not authorized" followed by the "authorized 3 out of 5 computers" message. Then I'm good to go...until I reboot or start my computer after it's been shutdown.
I've tried every step in this article multiple times, and it hasn't helped...http://support.apple.com/kb/ts1389
There is only one account on my computer and it's the admin account. I'm authorizing using my correct iTunes account name and password. Tried turning off and then on, user accouts and have deleted the SC folder...doesn't help at all...Like I said, it seems like I can authorize fine but as soon as I reboot or start my computer and then open iTunes, I'm told it's not authorized again.
Any ideas on how I can keep iTunes authorized? Running Windows 7, 64 bit on a Dell 9100 desktop...
Thanks,
Al

Iam also having the same problem, plus I have lost all sound from my player. My computer will play music through windows media etc and still has all system sounds its just itunes.
Is there any one from apple out there who can help?
P.C Windows XP

Itunes Won't Stay connected Keep

I keep trying to connect to Itune's and it keep saying to check my internet connection. I know my internet works so what is going on?

Well, it looks like it's being caused by SSID not being broadcast. As long as I have it broadcasting, all is well, as soon as I disable this, it won't connect after a restart.
This is my second iTouch, the first one had a bunch of dust appear under the glass and the Apple store replaced it no qualms, couldn't be happier My first iTouch didn't act this way and was running the previous version of software. It wasn't until i got a new unit and updated to this version that the issue started.
I have 2 other iTouch's in the home with the older software and they don't have any issues with SSID not being broadcasted.
Any additional thoughts?
Toy4Rick

ITunes won't stay where I put it

Normally I run iTunes in "minimized" mode (press the "+" button) and toss it all the way at the bottom left of my screen. It fits nicely right next to the dock so I always have it visible in a usually useless area of the screen.
In the past, it would occasionally jump vertically to be above the dock, typically if I opened other "iApps" or used a full screen game, but it would stay close to where I left it and I'd just need to drag it back down. Pressing the "+" button would have it end up where it belonged or just vertical of that spot.
Recently, the last 4-5 days or so, iTunes has decided it doesn't like that corner and more often than not "minimizes" to the exact center of the screen.
There's no pattern to it, just sometimes it stays where it belongs, other times it's right in the center.

My iTunes (8.0.2) recently started centering itself whenever I tried to move or resize it. Quitting and restarting the program seems to have fixed it for now.

ITunes won't even run

I just bought an iPod Nano, installed everything, updated everything, and when I try to open iTunes, I can't even get it to run. I am working on a Windows XP. Any help would be greatly appreciated. I've tried uninstalling and reinstalling. Even starting from scratch with nothing but what came on the disc with my Nano. Help Please!!

You may have already done this, but if not, you'll want to post this in another forum: iTunes for Windows. You'll find better help and advice there.

ITunes won't stay minimised

anyone else experiencing iTunes not staying minimised either to the system tray or the taskbar in Vista? .. I keep minimising it and it keeps popping back up again (just when you least expect it) - get's to be quite irritating when you're trying to do other things! .. I've tried repairing and reinstalling iTunes and played around with various settings within iTunes - but now I'm stuck .. any advice?

hey genius .. yes that's cracked it .. thought It might have been somethign to do with the iTunes sidebar gadget at one point (although removing that didn't help either), but completely forgot about my msn live messenger settings. .. shame though - I thought the messenger feature was kinda cool.
thnaks very much

ITunes won't stay closed

Pretty much what the subject says. I close iTunes, and 10(ish) seconds later it just opens up again on its own. I'm not doing anything with it (that I know of), but it just refuses to quit. Input? Thanks!

The latter is supposed to be there - I think it lets iTunes run faster (I saw it on Windows, too, when I used it). As for the iPod thing, I don't know whether or not that is true, but if it has been reported you should try it too. If the setting is on, turn it off, click Apply, and then reproduce your problem.

Mac won't stay running, no internet? PLEASE HELP!

Hi,
I have a 13" macbook pro.bought it refurbished and it was perfect- in january i brought it into a mac & pc repair shop since it was running a little slow and refused to burn CD's.
The problem they said was the operating system and the battery, so they reinstalled the operating system with an upgrade and the battery but now the laptop isnt running properly at all! ive never seen it so bad.
When it starts up it doesnt remember date & time, or network preferences. the battery condition says "replace" and when it does remember networks it wont connect as it says it doesnt have an IP address or has a self assigned IP address most of the time. and now wont stay powered on without the AC charger being plugged in even though its says its fully charged. The guarantee on the repair that i paid for isnt valid anymore.
how can i fix this? ive already reset the PRAM by holding down cmd,alt,P,R al at the same time as the computer starts up but hasn't helped.
These are the power stats.:
Battery Information:
Model Information:
Serial Number:          W01055TW4D3BA
Manufacturer:          SMP
Device name:          bq20z451
Pack Lot Code:          0000
PCB Lot Code:          0000
Firmware Version:          0201
Hardware Revision:          000a
Cell Revision:          0158
Charge Information:
Charge remaining (mAh):          5326
Fully charged:          Yes
Charging:          No
Full charge capacity (mAh):          5423
Health Information:
Cycle count:          57
Condition:          Replace Now
Battery Installed:          Yes
Amperage (mA):          0
Voltage (mV):          12459
System Power Settings:
AC Power:
System Sleep Timer (Minutes):          0
Disk Sleep Timer (Minutes):          0
Display Sleep Timer (Minutes):          0
Wake On AC Change:          No
Wake On Clamshell Open:          Yes
Wake On LAN:          No
Current Power Source:          Yes
Display Sleep Uses Dim:          No
Battery Power:
System Sleep Timer (Minutes):          25
Disk Sleep Timer (Minutes):          0
Display Sleep Timer (Minutes):          20
Wake On AC Change:          No
Wake On Clamshell Open:          Yes
Display Sleep Uses Dim:          No
Reduce Brightness:          No
Hardware Configuration:
UPS Installed:          No
AC Charger Information:
Connected:          Yes
ID:          0x0100
Wattage (W):          60
Revision:          0x0000
Family:          0x00ba
Serial Number:          0x002b46f4
Charging:          No

You might try a SMC reset:
http://support.apple.com/kb/ht3964
However I suspect you have some hardware issues that can best be addressed at an Apple store genius bar.
Ciao.

IPhone not recognized by iTunes, won't stay Off, etc

My iPhone started giving me an error message yesterday (happens about every 30 mins or so) that "This accessory is not made to work with iPhone"
The problem is nothing is connected to the iPhone! Additionally, whenever I connect the phone to my comp, iTunes fails to recognize it. So I can't do a Restore. In fact, it appears that the iPhone doesn't realize it is plugged in.
I was able to charge it from the wall charger last night, so I am pretty sure the connector "works."
Is there a way to reset the phone without using iTunes?
(Yes, I am the original owner. No, it is not jailbroken.)
Thanks!
-PAC

I am having a similar problem. I am attempting to install the airport extreme card in my ibook g4. The computer is not recognizing the card and now it isn't recognizing the iphone. If I remove the airport card then itunes recognizes the iphone. I have the original phone with the 2.01 update. I'm stumped.

Itunes won't stay closed and keeps opening itself

Can you help me

I've seen one report of that happening for a person because EyeTV was set to open iTunes when an export was finished.
Could you have some application set to start iTunes after a task is completed?

Windows 7; Printers Have Disappeared; Printer Spooler won't stay running.

I'm using Windows 7 Home Premium and an Epson Stylus Photo R220 printer. I also had a few virtual printers (ie: Snagit) installed before the problems started.
All of the printers (from my Devices and Printers) have disappeared, except for a generic "USB Printer" selection that shows it is my Epson R220. I can't print to it, and when I try to print a document and try to "Add Printer", a warning pops up saying "Can't
Add Printer. The local print spooler service is not running. Please restart the spooler or restart the machine." I've tried both with no success.
Sometimes, when I try to start the Print Spooler, I get a message "Error 1067: The process terminated unexpectedly." or it starts and just stops again.
I have also tried reinstalling the driver for my printer as specified from Epson's website, but the installer can't detect my printer, and if I try manually finding the port, nothing comes up, which I find odd since my computer recognizes when the printer
is attached.
Lastly, and I'm hoping it's not connected although I think it likely is, last night my computer had troubles starting Windows. So I did as it directed and I loaded my Windows CD into the computer and had it "Repair the problem". After several minutes, Windows
booted fine again.
Now I really don't want to have to reinstall Windows, as that will remove all of my program files, so I'm hoping that's not the only solution. Any ideas?

I have wrestled with this issue on a client's computer for a few days now and I am coming to the conclusion that a Windows Update (do not know which one) has caused the problem.
Windows 7 Professional 64-bit installation
Printers disappeared from Devices and Printers and from the list of printers within applications. A reboot does nothing and there is a DCOM error that occasionally pops up, but the client has only seen it and I don't know the specifics.
Any attempt to start the Print Spooler gives me a 1053 error, which is "The service did not respond to the start or control request in a timely fashion."
Doing a NET START SPOOLER from a command prompt gives me "The service is not responding to the control function."
As a last resort I did an in-place upgrade of Windows 7 (run setup on the installation DVD from Windows - not from boot - and choose the upgrade option. All Windows system files are restored and user information is left in tact.)
This completely solved the problem. After doing this, however, the Windows Updates need to be brought up to date, so I went through the updating process. 15 minutes after I left, the client called me and said his printers were gone again.
I have come back today to figure this out and after trying a couple more things I decided to do a System Restore, the last of which was created before the installation of Windows Updates. After running restore, the system rebooted and all printers
were there and the spooler was running normally.
Because I thought there was some other issue, I again ran Windows Update to bring back the same updates I had done before.
Guess what? No printers, spooler not working.
I am now going to restore again to before the 64 windows updates that installed and turn off the automatic update function until Microsoft figures out what is wrong and comes up with a patch.
This is what I believe the problem is. I am going to look at the list of updates and check to see if Microsoft did a DCOM update, because that might be the problem, since DCOM is a dependency of the spooler and because there was some kind of DCOM error.

Http listener won't stay running

Originally, I had to change the hostname in my listeners.ora file for the http/8080 listener to run at all. I have been running fine until recently (about 1 month). Now, it seems to start up and then die. Once it dies then I can't connect. lsnrctl status shows
Alias LISTENER
Version TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Beta
Start Date 02-SEP-2011 10:39:19
Uptime 0 days 1 hr. 13 min. 23 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Default Service XE
Listener Parameter File C:\oraclexe\app\oracle\product\11.2.0\server\network\a
dmin\listener.ora
Listener Log File C:\oraclexe\app\oracle\diag\tnslsnr\S928908\listener\a
lert\log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1ipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=S928908.srn.sandia.gov)(PORT=1521)))
Services Summary...
Service "CLRExtProc" has 1 instance(s).
Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
Service "PLSExtProc" has 1 instance(s).
Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
The command completed successfully
The alert_xe.log has this error over and over.
OER 7451 in Load Indicator : Error Code = OSD-04500: illegal option specified
O/S-Error: (OS 1) Incorrect function. !
Is that related?
I'm running the 11gR2 XE on Window 7 Enterprise 64bit.

WeaponsInfoSystem wrote:
Version TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - BetaTry the production release. It was released less than a day ago - see forum announcement.
The alert_xe.log has this error over and over.
OER 7451 in Load Indicator : Error Code = OSD-04500: illegal option specified
O/S-Error: (OS 1) Incorrect function. !
I'm running the 11gR2 XE on Window 7 Enterprise 64bit.There's no x64 version out yet. {thread:id=2277451}.

HT3819 iTunes won't stay running

Similar Messages

Maybe you are looking for