HT3819 My new Apple TV works fine but turns off Home sharing at regular intervals. This requires me to re-enter my itunes password and start over again. It is not my computer. I've checked and home share is still on in itunes. Any advice on where I should

I just installed Apple TV. Works fine but turrns itself off at regular intervals of about 30 minutes. This requires me to re-enter my Apple ID and re-start all over again. Wjen I check iTunes on my computer, home sharing is still turned on. THis leads me to think the problem is in how I configured Apple TV on my HDTV. Any advice on where I should look?
THanks in advance.

I have had no luck. After an hour with phone tech support I have re-installed the current Apple TV software update., re-booted the entire system three times., checked each of my two Airport Express's.,unplugged and re[plugged in every cable,  ad infinitum, ad nauseum and still no luck. I have also decided iTunes 11 *****. Not near as intuitive especially with regard to moving stuff around between my playlists, etc.
Alright guys, is this a problem because of iTunes 11? Is Apple releasing stuff before adequate debugging? Did Steve take his high standards with him?

Similar Messages

  • I just upgraded my operating sytem to 10.6.8, to accomadate my sons new ipod which worked fine , but on plugging in my iphone 4 , itunes doesn't rcognise my phone , just says no camera found, help please.

    I just upgraded my operating sytem to 10.6.8, to accomadate my sons new ipod which worked fine , but on plugging in my iphone 4 , itunes doesn't rcognise my phone , just says no camera found, help please.

    Try Here  >  http://support.apple.com/kb/ts1591

  • I HAVE A USER ID, A SYNC KEY BUT NO WORKING PASSWORD ; CAN I CANCEL THIS ATTEMPT AND START OVER again.

    i followed all the directions e ,mailed to me ,but when i tried to sync my iphone the error message said incorrect password. I then asked for a second set of instructions and redoubled my efforts and still no sucess i tried to reset tghe password but I don't have a sync tab setup under firefox/tools/options. If allowed to cancel the sync key and start over again knowing the pitfalls I have encountered I would be succeswful. i THINK FIREFox is the best system I enjoy using it every day. thankyou

    On the iPad tap Settings > iCloud
    Toggle Documents & Data off then back on then restart your iPad.
    Hold the On/Off Sleep/Wake button down until the red slider appears. Slide your finger across the slider to turn off iPhone. To turn iPhone back on, press and hold the On/Off Sleep/Wake button until the Apple logo appears.
    On the iMac open System Preferences > iCloud
    Deselect the box next to Documents & Data then reselect it then restart your iMac.

  • HT4889 Hi. I`ve just started transferring from my old Imac to a new Macbook, using the WIFI. But I realize it will take days to get it done. Can I cancel the process, and start over again using the thunderbolt port? Without causing any trouble?

    Hi. I`ve just started transferring from my old Imac to a new Macbook, using the WIFI. But I realize it will take days to get it done. Can I cancel the process, and start over again using the thunderbolt port? Without causing any trouble?

    See Pondini's Setup New Mac guide for possible answers.

  • Pls have been having issues upgrading to the os 10.9. downloads encounter error when it gets to 955mb and starts over again-.suggestions pls?

    pls have been having issues upgrading to the os 10.9. downloads encounter error when it gets to 955mb and starts over again….suggestions pls?

    http://www.apple.com/support/mac/app-store/contact/

  • I installed PP6 on my Lenovo Laptap with Win8.1. Worked fine. Turned off computer. Turned back on. Can not open ANY PP6 program.  No Adobe app shows as a listed program to uninstall.  However, Adobe PP6 files shows in directory search.  How do I fix?

    How do you uninstall PP6 with win8.1 when it no longer shows up as a program listed with an uninstall options.  PP  worked until I turned off computer and restarted.  All start up links are gone.   I can see where Adobe PP6 files installed when I do a directory search but no .exe start files in those directories work.  I can not uninstall PP6 and try again to re-install.    How do I fix this problem?

    Thanks Michael. Apologies for the slow reply I was away for a bit (holiday blitz at work and visiting family madness etc.etc.) back now, I set both options you requested to "never " and retried the CMS software with no change. 
    I do have progress of a sort though, as a test I took a separate test PC and put a clean install of Win7 on and loaded up the CMS software (it worked perfectly) and then took the version of ole32.dll off that machine and put it onto the computer I had built
    for her (using Linux) and...
    got a new error code. Darn I was so sure I had found a clever solution this time lol.
    Anyway now when the CMS fails it gives me a similar error but the offending module is "ntdll.dll" sooo... I tried taking the "working" version of ntdll.dll from the test box and moving it over (making sure to back up the existing ones
    first so I could put them back if needed) to her new PC and the PC would not boot. 
    It seems to want the original versions of a few Dynamic Link Libraries and if I could somehow give it those while not breaking Win7 it should theoretically work seeing as it no longer errors with ole32.dll. 
    ntdll.dll however seems necessary for Win7 to boot.
    So what I am wondering now is:
    Is there some way to have both versions of the DLL file in the system32 folder (bypassing the "cannot have two files with the exact same name in the same folder" thing) or rename the original DLL's something else and somehow make the CMS look for
    the new named versions so the system has the updated DLL's it needs to boot/run and the CMS has the old ones it wants to run or is there someway to have a self contained install of the CMS, say on a USB flash drive and give it it's own E:/windows/system32/needed
    dll's  path to the files it needs? 
    Willing to try any other options or settings you may have come up with as well.
    Thanks again for your reply and my apologies for not answering sooner.

  • Airplay movie stops and start over again

    I have problem with AirPlay while watching play-channels from my iPad. After a while the program just starts over again. What can I do to fix this?

    Welcome to the Apple Community.
    Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
    You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
    Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
    There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment.

  • HT1420 I have used all or almost all of my 5 authorized computers with my iTunes account. Several are for old computers. Is the best thing to do to deactivate all and start over? Is do not have these old computers anymore. Thanks!

    I have used all or almost all of my 5 devices under my I'd on iTunes. Several are on old computers no longer in my possession. Should I simply deactivate all devices and start over? I just want to make sure this does not invite unanticipated issues. Thanks,

    Yeah, if you're up to five authorisations I'd deauthorise all and then reauthorise the ones you still have access to.

  • I phone frozen Can anyone help, my iphone is frozen with a screen that shows Itunes logo an arrow and USB cable. Tried to reset, Apple screen comes up, the itunes screen, then shuts off and starts over again. Any ideas, this happened while updating.

    Help my iphone is frozen in a screen with iphone logo and usb cable.  Happened while I was updatting.

    plug it in youre computer and hold the power button and the home button for 30 seconds and then it should have a blck sctreen then press the on button for 15 seconds and an apple logo shoul appear. please answer my problem.

  • As a novice emailer, I keep getting "Firefox prevented this page from automatically redirecting to another page" and I have to close and start over again EVERY TIME.

    I don't use this computer's new gmail very often. Therefore, I had some 150 emails that I was trying to go thru & delete if possible. Many emails gave another site to go to complete my understanding of this email. But "Firefox prevented...." statement appears on the top w/ only a blank screen. I try to go back a page...nothing happens. I have to close all the tabs and get out of it completely. Then I have to click on Firefox icon...go to gmail...select the same email if there was more to read on it or just skip to the next new email. Very frustrating to a computer-illiterate. I don't understand any of the computer lingo (jave...etc); it took me 1 hour to figure out how to get to this space to type in this question. I have already failed 3 times in asking/typing in the question box. PLEASE try not to give me technical phrases.....left, right, top, works best for me.... mahalo, cecile

    I don't know if this is still a problem but to stop it go to Firefox>Options>Options>Advanced>General Then third line down there is a box to remove the warnings. (These instructions are for Firefox4; I don't know how to access this from other versions.)
    I'm also not sure whether this just removes the service of stopping redirection or whether it just removes the warning so beware.

  • Why can I only download 25 mb of itunes 10.6 and at 25.1 mb, it resets and starts over again????

    This is making me want to throw the iphone, the iMac, the windows pc (because it has itunes on it) and anything else related to apple into the freaking ocean and even stop eating apples.  I have been searching the web rying to find answers and always get sent to the "support" community.  Jock straps and bras are support... this community is a place for frustrated users to vent--thats it!  I never once seen anyone from apple get on here and help out.  The only support you get from apple has to be bought.  I don't even know why I am complaining about free software...IT'S FREE, hence the lack of apple support.  Oh well, I will just add the 5 minutes of wasted time I used to type this to the hours and hours of wasted time I have spent dealing with this.  I hope everyone here (besides apple "support team" has a great day, night or whatever it may be where you are.

    iTunesux wrote:
    this community is a place for frustrated users to vent--thats it!  I never once seen anyone from apple get on here and help out. 
    Had you bothered to read the terms of use that we all agreed to when signing up to post here, you would have seen explicitly that this IS a user to user technical support forum and Apple has no presence here.
    Think you could stop ranting for 2 minutes, pull your head out of your rear-end and provide some details of the issue you're having? 

  • Limited history available with "go back" button -- maybe 30-40 pages, then must go to initial page and start over again. Can I take page limit off of Go Back button?

    When using "firstview.com" and scrolling through pictures, I wish to return to my initial viewing page. I use the "go back" button and am able to return 30 or so pages, and then it does not allow further "go back." Can I increase or eliminate the limit on the capacity to go back using the go back button?
    == This happened ==
    Every time Firefox opened
    == n/a

    You can try to increase the pref '''browser.sessionhistory.max_entries''' on the about:config page.
    To open the ''about:config'' page, type '''about:config''' in the location (address) bar and press the Enter key, just like you type the url of a website to open a website.
    If you see a warning then you can confirm that you want to access that page.

  • My apple tv worked fine till i got new Panasonic 55 plasma. now the tv doesnt recognized the hdmi unless i unplug and replug the apple tv.

    my gen 2 apple tv worked fine on my 5 yo Panasonic Viera with HDMI cable.
    i bought new 55 inch Panasonic and new hdmi cables.
    the apple tv works fine but...if i turn off the tv and leave it off for a while, then try to watch apple tv, the apple tv is off and no signal seen at the tv
    if i unplug and replug the apple tv it reboots and works fine on the tv
    i tried with three diff hdmi cables and three diff ports on the tv.. all same problem
    help

    After successfully logging onto your network, your tv screen should display a 5 digit passcode for you to enter into your mac. Does it do this.
    The tv should now have appeared in your device list in itunes and by clicking on the device you should be able to enter the passcode to register with itunes. Can you do this.
    I suspect you can do neither from what you have said but whilst I wouldn't be surprised if the later didn't happen, I'd be surprised that the former didn't.

  • I updated an app on my iPhone 4 and it has went onto the loading icon but has stalled, the phone works fine but I can't download anymore apps help?

    I updated an app on my iPhone 4 and it has went onto the loading icon but has stalled. The phone works fine but i cant download anymore! Anyone had this before

    The app store has been down at times throughout the day today.
    Just be patient and wait it out.

  • I seriously don't know what caused this to start being a problem until today it worked fine, but I added an exception for popups full question in DETAILS

    is there anyway to allow Firefox to allow pop ups from this 1 page of Facebook / well this 1 game https://apps.facebook.com/vampiresdarkside/ and not the entire pan in the Ass Pop up happy site, I cant see any sense in allowing popups from all
    apps.facebook.com
    and when I try to add it as the exception should be your program edits it to be that crap above instead of the exception I entered specifically,
    apps.facebook.com/vampiresdarkside/
    I seriously don't know what caused this to start being a problem until today it worked fine, but I added an exception for popups from this one site in Chrome and Firefox decided it wouldn't allow it popups from this part of Facebook and no I am not allowing all the FB apps to have popups I never had to before
    apps.facebook.com/vampiresdarkside/
    have popups after adding the popup exception in chrome, and no I did nothing to Firefox but it is kinda asking me to switch to Opera or some other crap browser with it acting like this, I modified the exception in chrome and Firefox now wont allow the pop ups it always had up until chrome allowed them WTF

    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
    *Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
    *Do NOT click the Reset button on the Safe Mode start window
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
    Do a malware check with several malware scanning programs on the Windows computer.
    Please scan with all programs because each program detects different malware.
    All these programs have free versions.
    Make sure that you update each program to get the latest version of their databases before doing a scan.
    *Malwarebytes' Anti-Malware:<br>http://www.malwarebytes.org/mbam.php
    *AdwCleaner:<br>http://www.bleepingcomputer.com/download/adwcleaner/<br>http://www.softpedia.com/get/Antivirus/Removal-Tools/AdwCleaner.shtml
    *SuperAntispyware:<br>http://www.superantispyware.com/
    *Microsoft Safety Scanner:<br>http://www.microsoft.com/security/scanner/en-us/default.aspx
    *Windows Defender:<br>http://windows.microsoft.com/en-us/windows/using-defender
    *Spybot Search & Destroy:<br>http://www.safer-networking.org/en/index.html
    *Kasperky Free Security Scan:<br>http://www.kaspersky.com/security-scan
    You can also do a check for a rootkit infection with TDSSKiller.
    *Anti-rootkit utility TDSSKiller:<br>http://support.kaspersky.com/5350?el=88446
    See also:
    *"Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked
    *https://support.mozilla.org/kb/troubleshoot-firefox-issues-caused-malware

Maybe you are looking for