HT3964 I did the SMC reset for my iMac intel-based and now it won't turn on. What can I do to fix this?
I did the SMC reset for my iMac intel-based and now it won't turn on. What can I do to fix this?
Well, first things first... is the power cord fully plugged into the back of the iMac (and the wall, for that matter)?
Make sure the wall outlet has power, too... I've scratched my head over stupid issues where I forgot to flip a wall switch.
If the outlet does have power, then try doing a pram zap. Command + option + P + R (hold those at startup).
If the machine is receiving power, you should be able to see some LEDs if you look through the bottom grate of the machine to the left of the RAM door.
Similar Messages
-
My macbook pro loads webpages fine for the first few minutes but after that the internet freezes and will not load anymore webpages. What can I do to fix this?
I let Firefox sit on my desktop for about five minutes, and it finall allowed me to use it. That is EXTREEEMELY slow. What is the problem?
-
One week ago my iPhone felt, the screen was damaged but it was still working. Today it felt again and now it doesn't turn on, what can I do? Please help me.
Hold down on the sleep button and the home button at the same time for about 10 seconds until the Apple logo appears on the screen. Ignore the red slider. When the logo appears let go of the buttons.
-
I am unable to sync all my selected songs to my iphone. The error message is that the computer is not authorized. However, I have authorized the computer and iTunes confirms that. Any ideas what can be done to fix this. My phone is an iPhone 4S.
Were some of the songs purchased from a different itunes account?
-
I reset everything on my iphone 4 and now it's stuck on a loading scree and my lock button is broken. what do i do?!
There is nothing you can do as you won't be able to reset the device.
You can wait until the battery goes flat then try connecting it to power so it restarts. If the same issue occours then you'll need to restore it on iTunes by entering recovery mode. -
I recently upgraded to to the iOS 5 on my iMac and iPad. Now when i sync my iPad it get stuck on step 8 with a prompt that says "waiting to copy items" it stays on like that for hours. When I eventually do disconnect my iPad it says sync is not complete. Now, some of my album artwork is not copied into my iPad but on iTunes in my iMac desktop everything is still there. Pulling my hair out with this one. Please help!
my iPad it get stuck on step 8 with a prompt that says "waiting to copy items" it stays on like that for hours
Reset your iPad.
Hold the On/Off Sleep/Wake button and the Home button down at the same time for at least ten seconds, until the Apple logo appears.
I recently upgraded to to the iOS 5 on my iMac and iPad
You don't need to manually sync using iOS 5.
Help here > Apple - iCloud - Learn how to set up iCloud on all your devices.
Message was edited by: Carolyn -
I
If you have Adobe Acrobat installed on your computer, and don't see the Acrobat Ribbon in Microsoft Word there can be a couple of things to check:
First of all check which version of Adobe Acrobat you have installed (Help menu > About Adobe Acrobat), then see if it is compatible with the version of Word you are using. Use the following link to check what the compatible versions are: Compatible web browsers and PDFMaker applications for a list.
If you find your version of Adobe Acrobat is fully compatible, then check and see if you have the latest updates for Adobe Acrobat installed. From the Help menu > Check for Updates. If any updates are listed, install them, by following the prompts in the dialog boxes that pop-up.
Once you've updated, reboot your computer, then launch Microsoft Word again: Is the Acrobat Ribbon available now? If not, then you might need to check and see if the PDFMakerOfficeAddin is enabled in Word - The following link provides steps on how to do this. PDFMaker unavailable | Office 2007, Office 2010 | Acrobat 9, Acrobat X, Acrobat XI
Hope this helps,
Cari -
Hey,
I keep trying to empty the trash on my macbook pro as it says i have just under 2gb of harddrive space left. I can't update my software as i don't have enough harddrive space left.
Every time i try and empty the trash it says that it can't empty the trash and gives an error code -8003.
Any ideas how i can fix this?
Many Thanks,
CharlieCan't empty trash:
http://support.apple.com/kb/HT1526?viewlocale=en_US
How to Force Empty the Trash:
http://www.thexlab.com/faqs/trash.html#Anchor-Force-11481 -
Reset ipod back to factory yesterday and now it won't turn on
I rest ipod touch back to factory yesterday and now it doesn't come on at all
First thing to try is a reboot by holding both the power and home buttons until the apple logo appears, ignore the red slider if that appears.
Next would be the troubleshooting in http://support.apple.com/kb/TS3281 -
I went to shot a video today fort he first time, but the video button would not select so I couldn't shoot a video all other buttons worked, I could take photo etc., but could not do a video; anything?
Swipe up or down to select video option.
-
I just reset my passcode on my Ipod Touch, turned it on and it locked me out. Is there a way to get this reset?
Place the iPod in recovery mode and then restore the iPod via iTunes on your computer. For recovery mode:
iPhone and iPod touch: Unable to update or restore -
I was walking and I dropped my iPod and I picked it up and it was blue so I tried turning it back on and it wouldn't what do I do any help
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
My wife and I are using the same apple ID. Up until last week we used to buy an app and pay for it only once, but use it on both devices.
since last week, the app store asks me to pay again for an app i already paid for on one device. On both devices automatic downloads (in settings) is and was always turned off.
what can I do to fix this?Actually no. After installing an app on one device, I used to see an "install" button on the second device (since it's already been paid for). Now i get the full price button on the second device. I didn't want to proceed with the purchase because i didn't want to be billed twice.
-
My MacBook Pro 2009 won't turn on. It suddenly won't charge and when it did, I shut it down and now it won't turn back on. Charging shows green and the green little dots are showing on the side. I tried smc reset, command+p+r. Any other suggestions before i take it to apple service center?
A four year battery could be dead. I'd contact an Apple Service Center.
-
My ipod touch needed to be updated so I did and now it won't turn on all it does is show the itunes icon and says toconnect it to itunes so I did and let it be updated and now it wont turn on and I tried resetting but nothing changed.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Maybe you are looking for
-
ITubes crashes when selecting tv programmes or podcasts in custom sync
Hi i want to set up my apple TV to custom sync but whenever i select this option then go to either tv programes or podcasts section it just crashes itunes. I have 160Gb model apple TV (iTunes says 144Gb so i assume it's 160 can't rememeber) and the l
-
Error in at line-selection event...
Hello experts, In my report, I am hiding the values of BUKRS, ANLN1 and ANLN2 during my loop. I am using field symbols as my work area for my itab which is it_output. The problem is, when I try to do this in my at line-selection event: at line-select
-
Change background color of ITS iViews
Hello Forum, We successfully created our own theme in the portal and used the ITS theme generator to create the ITS specific parts. This seems to work, but we need some more finetuning. One specific question is about the blue green as default, but we
-
LabVOOP article - Reusing Code by Inheritance
I've posted a new article this weekend to EXPRESSIONFLOW in an article series Introduction to Object-Oriented Programming in LabVIEW. Reusing Code by Inheritance The previous articles in the article series are: Inheritance and Class Hierarchies in Ob
-
Different masterhead image based on the user logged in portal
HI, Presently we are using standard portal theme.How can I change the image in the masterhead based on the user logged in.How can i change that and i want to assign that masteredhead to users. Can anybody give me suggesion about this. Thanks, Regards