HT4060 I mistakenly finish the power of my Ipad 4 and since is not take charge again

I mistakenly finish the power of my Ipad 4 and since is not take charge again

Are you trying to charge it via a computer's USB port or the wall charger ? If a USB port then a lot of computers don't provide enough power to their charge the iPad at a sufficient rate (though it mat still charge the iPad if it's screen is off).
If the wall charger then you are using the iPad's own charger (and not an iPod or iPhone charger which are less powerful), and if so have you tried a reset to see if it charges after the iPad has restarted ? Press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
Otherwise have you got a different charger and/or cable that you could try ?

Similar Messages

  • Pls i tried to update my iphone, but the itones can restore my iphone and now its not coming up again

    Pls i tried to update my iphone, but the itones can restore my iphone and now its not coming up again, it can restore and its just displaying itunes logo and USB cable, pls i need your assistance and advice.

    Hello Richyfromnig,
    Thanks for using Apple Support Communities.
    The iTunes logo on the phone means that it is in what's called recovery mode.  Take a look at this article to find out more about recovery mode, and how to fix it:
    If you can't update or restore your iOS device
    http://support.apple.com/kb/ht1808
    Take care,
    Alex H.

  • 2005 ipod classic and it will not take charge in the wall or computer.

    Hello, i have a 2005 ipod classic. It wont take charge in the wall or computer. it only works with the car charger/player and before it works it take about 15 seconds to boot. when plugged in wall or computer it only says please wait very low battery and it will sit like that for hours. I've replaced the battery once before and it worked for a month then it started doing this again. is there any way to get it working by doing it myself?

    Replacing the battery is a rather delicate operation best left to the Apple techs.  If you do any damage Apple will not touch it or give any help, even on a device out of warranty.  It sounds like a new battery is in order.

  • My ipad 2 just went off. It was working perfectly while charging. I have pressed the power button for ten seconds and it's still not coming on. What do I do?

    My ipad 2 just went off. It was working perfectly while charging. I have pressed the power button for ten seconds and it's still not coming on. What do I do?

    First, confirm that the iPad is charged and then try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad.  Again, say "yes."
    Finally, if the Restore doesn't work, let the battery drain completely.  Then recharge for at least an hour and Restore again.

  • TS2518 Help, I had aperture open and working on a image and did not have a battery in and bumped the power off. As a result it will not open my master, it is locked. when I try to open that Library  it says There was an error opening the database for the

    Help, I had aperture open and working on a image and did not have a battery in and bumped the power off. As a result it will not open my master, it is locked. when I try to open that Library  it says There was an error opening the database for the library. I have tried every thing. I updated the other libr but now it will not open the main to update. What do I do?

    Try starting Aperture with the command and option keys held down.  You'll get 3 options.
    Try each, starting at the top, in order, checking after each to see if it fixes the issue.

  • The Power Supply Fan is still working, but does not appear to respond to increased loads, and its speed cannot be increased using SMCFanControl. Any suggestions?

    Hi all - My mac pro 1,1 has an enigmatic problem. It's quad-core, 3Ghz, running OS X 10.7.5. The problem began some months back, when running HD video conferences, HD streaming videos and some other graphics-moderate (I won't say intense) uses, such as slide shows in Just Looking. My machine has an ATY, RadeonX1900 card and 2 monitors - both Apple displays, one being 30 inch 2560x1600, the other being 24 inch 1920x1200.
    When I start those types of graphics-moderate apps, after about 5 minutes, something would crash (the monitors making a noise as it did) and the displays would both go black. The power did not appear to be fully cut off from the monitors. I think that the underlying applications, however, did not crash. So, I could still hear and speak to people during video conferences, and I could hear the sound tracks of videos.
    Attempts to restart the computer and get the monitors back did not immediately work to undo the problem, if done straight away. The only way to correct the problem (so as to have the monitors work) was to wait for a few minutes and then restart.
    After a lot of puzzled looking at console logs (and I confess that I am not an expert), I ran into a blank.
    But, because of the timing of the crashes (after ~5minutes use) and restarts (after some minutes wait), I reasoned that the problem might be temperature related.
    Once on that path of thought, I found this article:
    http://worldtv.com/blog/guides_tutorials/fixing_an_overheating_mac_pro_no_expens e_required.php
    I installed both Temperature Monitor and SMCFanControl. And I experimented, and got interesting results:
    Now to the puzzling bit: SMCFanControl shows that the speed of the Power Supply Fan doesn't vary much, even if I use SMCFanControl to ramp fan speeds right up. All of the other fans react to SMCFanControl, going up to and above 2500rpm when commanded. But the Power Supply Fan does not.  Having watched it for a few days now, the Power Supply Fan, according to AFCFanControl, never varies outside of a range from about 600-640 rpm, regardless of what I do with AFCFanControl.
    Also (and not surprisingly), whenever the graphics-moderate apps run, when I ramp all the fan speeds up using SMCFanControl, Temperature Monitor shows that the all of the temperatures within the machine plummet, except in the power supply locations. Power Supply Location 2 is the worst affected. Because the Power Supply Fan does not react as the other fans do, the "crashes" still occur.
    I could post some screen shots of the read outs of SMCFanControl and Temperature Monitor, although I think I have covered the key points in this post.
    It seems that the Power Supply Fan is still working, but does not respond to increased loads.
    Instinctively, I'm worried that if that's right, it might be a hard problem to fix. Any suggestions? Help! I would really appreciate them!
    Cheers
    P

    Thanks for your response Grant. I had already read about, and I think excluded, dust in graphics card/fan/assembly as a cause. The entire inside of the computer, including the graphics card/fan/assembly, is as clean as a whistle. It looks clean. I've cleaned the dust out every now and then (including a few days ago). Also, my undersanding (derived from the article, linked in my first post) is that I might expect to see high temperatures in the Northbridge and memory module B if the graphics card was overheating. According to Temperature Monitor, however, locations do not increase in temperature when I run the relevant apps. Finally, the graphics card/assembly does not feel too hot to touch.
    It is strange that SMCFanControl lists the Power Supply Fan as being software controllable, if that fan is not. Still, your comments are consistent with my observations, as the fan simply does not respond to software control.
    There are two upsides: First, I've something of a work-around. I've worked out what temperature must be achieved in Power Supply Location 2 for a crash to occur, and I can watch that location in Temperature Monitor, terminating the process before that treshold is reached. Of course, that's not ideal. Second, ramping all the other fans up does significantly delay the onset of the problem, and makes recovery time much quicker.
    Is there any donwside to peridically ramping up the other fans when running the relevant apps? Given that it causes all of the other locations to cool significantly, could this lessesn the life expecancy of the mahcine? (I don't want to run the fans up all the time - that's like sitting next to a jet ready for take off!)
    Also, a correction to my first post: Yesterday, with all the other fans running on full and running an HD streaming video, the Power Supply Fan did, eventually, slowly, come up to ~740rpm, which is much higher than the ~640rpm maximum I had previously seen, and this may have aided delaying the onset of the problem. 
    I'm not sure where this leaves me? The problem might now be able managed. Well, sort-of. But it's not eliminated.

  • I have a Mac G4 double mirrored model and everytime I shut it off it will not go on when I hit the power off button. However, if I unplug and plug in the power cord it boots fine and everything is OK. The PMU and logic board have been reset. Any ideas?

    I have a Power Mac G4 double mirrored model and everytime I shut it off it will not go on when I hit the power on/off button again. However, if I unplug and plug in the power cord it boots fine and everything is OK. The PMU and logic board have been reset. Sometimes my Mac goes on just by pressing the power on button but most times I have to pull the power cord and put it back in. Any ideas or help out there for this? Could it be a failing power supply? Apple Care says that this model is obsolete so there is no help from there. John
    <E-mail Edited by Host>

    Hi John,
    That's often a sign of a bsad Capacitor in the Power Supply, but...
    Might be time to replace the PRAM Battery, 4 years is close to their lifespan, far less if ever without AC power, & can cause strange startup problems...
    http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/ 

  • Hi i uppdate my I phone 4 to iso6 via laptop ,during the operation the laptop restart it's self then I connect my iPhone 4 to iTunes again to finish the uppdating but its stuck to Apple log tried to restor it again via iTunes i get the same stuck to logo

    Hi i uppdate my I phone 4 to iso6 via laptop ,during the operation the laptop restart it's self then I connect my iPhone 4 to iTunes again to finish the uppdating but its stuck to Apple log tried to restore it again via iTunes i get the same problem its stuck to Apple logo i tried to restor it from another pc i get the same problem anyone can help please

    Hi, did you ever solve this problem?
    My 1 year old -- ha! one month out of warranty -- iPhone 4 has been having a nearly identical problem over the past few days.
    It started by dying completely so I had the battery replaced, thinking it was simply battery issue.
    It then worked again for a moment but started doing exactly what you describe, going through a reset cycle (longer than 30 seconds but who's counting). And it felt quite warm.
    Did hard reset, plugged into wall charger and MBP USB but the new battery wouldn't even get a full charge (a whopping 92% after nearly two days). It would even lose battery when plugged in if I opened an app. And all the while plugged in, if I left the phone on, it would cycle through these resets. So I turned it off to try to charge it.
    Now suddenly, it's dead again. Totally black, and hard reset does nothing. Up until two days ago there was nothing wrong whatsoever with this phone! And I hadn't even installed a new app that could be the root of the issue. No idea whatsoever what caused this.
    Any help would be much appreciated!!

  • After resetting my phone to factory settings, it will not turn on. When i press the power button a white screen and black apple pop up. it stays on that screen and will not go to the home screen, it will just die. please help!

    after resetting my phone to factory settings, it will not turn on. When i press the power button a white screen and black apple pop up. it stays on that screen and will not go to the home screen, it will just die. please help!

    Make sure it is charged for about 10min using the adapter, then connect in recovery mode, explained in this article:
    If you can't update or restore your iOS device

  • I have a iPhone 3GS and the power connection prongs are damaged and it won't charge or sync.  Is there any way to repair?

    I have a iPhone 3GS and the power connection prongs are damaged and it won't charge or sync.  Is there any way to repair?  Or, at least is there a way to charge so I can write down phone numbers and othe rinformation.  My power charge is totally out right now.

    If it will not turn on - you have zero chance of getting anything off the phone.

  • I have virgin mobile iphone that i found,the power button doesn't work and the phone is now saying disalbed what can i do to fix it

    I have a virgin moble iphone that i found, the power button doesn't work and the phone is saying disabled,what can i do to fix it?

    Probably nothing, the phone has a high likelihood of being stolen and if you try to Restore it you will run into Activation Lock. Turn it in to the local authorities.

  • I am john and I need help downloading a progmmme yesterday and wanted to finish downloading open it and I am not told me that the program was shut down unexpectedly and restart ponia not opened and went back to download it and not opened my back probe to

    i am john and I need help downloading a progmmme yesterday and wanted to finish downloading open it and I am not told me that the program was shut down unexpectedly and restart ponia not opened and went back to download it and not opened my back probe to turn off the computer and there was no case

    i am john and I need your help yesterday bought a program called DJAY when I finish the download and got an error opened and I saw him there was no case to install and thank you for your help anyway

  • My ipod comepletly froze and ive googled and youtubed ways to fix it! its on recovery mode and when i hold the home and power button it shows the apple button for a second and then it shows recovery mode again! i need help i DONT wanna restore!

    My ipod comepletly froze and ive googled and youtubed ways to fix it! its on recovery mode and when i hold the home and power button it shows the apple button for a second and then it shows recovery mode again! i need help i DONT wanna restore!
    ive read that alot of ppl are having this problem i need my ipod so if someone can help me ASAP

    Here is what you should do turn the device on hold the home button and the power button until the device turn off keep holding and when the device reboots release the power button but hol the home button until it shows the iTunes logo then restore it

  • HT4623 My iPhone has suddenly stopped working. It now says the battery is dying and to charge it. After charging it for over an hour, there is no change. The power won't come on, and I am left with a blank screen advising me to plug my phone into the char

    My iPhone has suddenly stopped working. It now says the battery is dying and to charge it. After charging it for over an hour, there is no change. The power won't come on, and I am left with a blank screen advising me to plug my phone into the charger.

    Try different USB Cable, try different Charger. Clean iPhone charging port with clean dry toothbrush. If still problem and you have Warranty or AppleCare, make Genius reservation and take iPhone to Apple for resolution. If no coverage, most likely it could be battery or charging port assembly that need replacement.

  • Have upgraded to Lion 10.7 from 10.6 and now it keeps logging off abruptly though the power settings are proper and i can not take backup using timemachine. any help welcome...

    Have upgraded to Lion 10.7 from 10.6 and now it keeps logging off abruptly though the power settings are proper and i can not take backup using timemachine. any help welcome...

    Have upgraded to Lion 10.7 from 10.6 and now it keeps logging off abruptly though the power settings are proper and i can not take backup using timemachine. any help welcome...

Maybe you are looking for