HT4061 how to enabled my ipad

Please help me to enabled my ipad as i can not do it with itunes.

What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Update and restore alert messages on iPhone, iPad, and iPod touch
http://www.buybuyla.com/tech/view/012953a0d412000e.shtml
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
 Cheers, Tom

Similar Messages

  • How to enable my ipad air coz of wrong password and Findmy ipad air is on

    How to enable my ipad air because of wrong password and i cannot recover or restore my device coz Find my ipad setting in my device is on. Itunes said this must be off before anything, but i cannot turn it off in setting because device is disable. Help me

    Try DFU mode:
    Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
    Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
       1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
           other end of the cable connected to your computer's USB port.
       2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
           until the red slider appears, then slide the slider. Wait for the device to turn off.
                  * If you cannot turn off the device using the slider, press and hold the
                    Sleep/Wake and Home buttons at the same time. When the device turns off,
                    release the Sleep/Wake and Home buttons.
      3. While pressing and holding the Home button, reconnect the USB cable to the
           device. The device should turn on. Note: If you see the battery charge warning,
           let the device charge for at least ten minutes to ensure that the battery has some
           charge, and then start with step 2 again.
      4. Continue holding the Home button until you see the "Connect to iTunes" screen.
           When this screen appears you can release the Home button:
      5. If necessary, open iTunes. You should see the following "recovery mode" alert:
      6. Use iTunes to restore the device.
    If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
    Additional Information:
    If you have a problem getting into recovery mode then try: RecBoot: Easy Way to Put iPhone into Recovery Mode.
    Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

  • How to enable my Ipad after it has been dissable by too many wrong attempts to enter passcode?

    How to enable my Ipad after it has been dissable by too many wrong attempts to enter passcode?

    You have to restore the iPad in order to unlock it using these instructions.
    http://support.apple.com/kb/HT1212?viewlocale=en_US&locale=en_US

  • How to enable my ipad air..

    how to enable ipad air...??can somebody help me..

    iPad disabled?
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.

  • How to enable my IPad.

    My Ipad mini is disabled due to too many failed attempts to log on with new pw....I wen to Itunes site as it instructed but it says that I have to enter my pw into the device, but it wont let me add the password because it is disbled. How can I enable my Ipad? Thank you.

    FORCE IPAD INTO RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.

  • How to enable back ipad if on disabled mode?

    Anybody can help me on this , I forget my passcode. How to enable back my Ipad?

    If you've never synced then you won't have a backup on your computer and you will therefore lose all your content from the iPad. You need to connect your iPad to your computer's iTunes - see this page for a locked iPad : http://support.apple.com/kb/HT1212 . You may need to put the iPad into recovery mode first : http://support.apple.com/kb/ht1808

  • HT4061 How to restore my ipad after downloading itunes?

    How to restore my ipad after downloading itunes?

    Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
    Before restoring:
    Verify that you are using the latest version of iTunes.
    Back up your device.
    Transfer and sync content to your computer.
    Restoring your iOS device
    Connect your device to your computer.
    Select your iPhone, iPad, or iPod touch when it appears in iTunes. Select the Summary tab, and click the Restore button.
    Click Restore.
    After a restore, the iOS device restarts. You should then see "Slide to set up". Follow the steps in the iOS Setup Assistant.
    If needed, restore your device from a previous backup.
    If restoring does not finish successfully or if a restore error appears, see iOS: Resolving update and restore alert messages.
    Additional Information
    If your device is continually restarting, not responding, or showing the Apple logo with no progress bar or a stopped progress bar, place the device into recovery mode and try restoring again.
    Devices with cellular service should activate after a restore. If activation is not successfu, see the options below.
    Symptoms
    Your iPhone may display one of the following messages when you attempt to activate it:
    "Your iPhone could not be activated because the activation server is temporarily unavailable."
    "The iPhone is not recognized and cannot be activated for service."
    "iTunes was unable to verify your device."
    Resolution
    Perform the following steps if you receive one of the messages above:
    Restart the iPhone.
    Try another means of reaching the activation server and attempt to activate.
    Try connecting to Wi-Fi if you're unable to activate using a cellular data connection.
    Try connecting to iTunes if you're unable to activate using Wi-Fi.
    Restore the iPhone.
    If you receive an alert message when you attempt to activate your iPhone, try to place the iPhone in recovery mode and perform a restore. If you're still unable to complete the setup assistant due to an activation error, contact Applefor assistance.

  • HT204053 How to enable my Ipad

    how to enable my Ipad

    Does it say it is disabled?
    Forgotten Passcode or device disabled after entering wrong passcode

  • HT4061 how to find my ipad serial number

    I'm trying to find my IPad serial number
    Also I'm not receiveing my email

    If you don't know your lost/stolen iPad's serial number, use the instructions below. The S/N is also on the iPad's box.
    How to Find Your iPad Serial Number
    http://www.ipadastic.com/tutorials/how-to-find-your-ipad-serial-number
     Cheers, Tom

  • HT4061 How to track stolen ipad mini wifi?

    Can any please help me is there a possibilty to track stolen ipad.
    Regards,

    What To Do If Your iDevice Is Lost Or Stolen
    If you activated Find My Phone before it was lost or stolen, you can track it only if Wi-Fi is enabled on the device. What you cannot do is track your device using a serial number or other identifying number. You cannot expect Apple or anyone else to find your device for you. You cannot recover your loss unless you insure your device for such loss. It is not covered by your warranty.
    If your iPhone, iPod, iPod Touch, or iPad is lost or stolen what do you do? There are things you should have done in advance - before you lost it or it was stolen - and some things to do after the fact. Here are some suggestions:
    This link, Re: Help! I misplaced / lost my iPhone 5 today morning in delta Chelsea hotel downtown an I am not able to track it. Please help!, has some good advice regarding your options when your iDevice is lost or stolen.
      1. Reporting a lost or stolen Apple product
      2. Find my lost iPod Touch
      3. AT&T. Sprint, and Verizon can block stolen phones/tablets
      4. What-To-Do-When-Iphone-Is-Stolen
      5. What to do if your iOS device is lost or stolen
      6. 6 Ways to Track and Recover Your Lost/Stolen iPhone
      7. Find My iPhone
      8. Report Stolen iPad | Stolen Lost Found Online
    It pays to be proactive by following the advice on using Find My Phone before you lose your device:
      1. Find My iPhone
      2. Setup your iDevice on iCloud
      3. OS X Lion/Mountain Lion- About Find My Mac
      4. How To Set Up Free Find Your iPhone (Even on Unsupported Devices)

  • HT4623 how to enable my ipad?

    My daughter was playing with my ipad and how it say" ipad is disabled" connect to Itunes. When I connect to Itunes nothing happens.

    iOS: Device disabled after entering wrong passcode
    http://support.apple.com/kb/ht1212
    Using iPhone/iPad Recovery Mode
    http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
     Cheers, Tom

  • Can someone tell me how to enable and ipad that has been disabled without using iTunes

    My sons ipad is in disabled mode and his mom doesn't have access to iTunes. Can anyone tell me how I can get it working again?

    Take it to an Apple Store for assistance. However, the iPad will be returned to its out of the box configuration (erased). You may be asked to provide proof that the iPad is yours.
    Make a Genius Bar Reservation
    http://www.apple.com/retail/geniusbar/
     Cheers, Tom

  • HT4061 How to check if iPad is new ipad or iPad 2 ?

    I have recently purchased a new iPad. But surprisingly I cannot identify visually if it is new iPad or iPad 2!!!! Can someone help me ? I purchased this in china

    Here's the various iPad model numbers and order numbers. The model numbers are on the back of the iPad
    Apple iPad Wi-Fi (Original) 16, 32, 64 GB
    The wi-fi only iPad configurations are assigned model number A1219.
    MB292LL/A is the order number for the 16 GB configuration. The 32 GB configuration is assigned MB293LL/A and the 64 GB configuration is assigned MB294LL/A.
    Apple iPad Wi-Fi/3G/GPS (Original) 16, 32, 64 GB
    The Wi-Fi/3G/A-GPS iPad configurations are assigned model number A1337.
    MC349LL/A is the order number for the 16 GB configuration. The 32 GB configuration is assigned MC496LL/A and the 64 GB configuration is assigned MC497LL/A.
    Apple iPad 2 (Wi-Fi Only) 16, 32, 64 GB
    The wi-fi only iPad 2 configurations are assigned model number A1395.
    MC769LL/A is the original order number for the 16 GB configuration in black. The 32 GB configuration in black is assigned MC770LL/A and the 64 GB configuration in black is assigned MC916LL/A. The original 16 GB, 32 GB and 64 GB configurations in white are assigned MC979LL/A, MC980LL/A, and MC981LL/A, respectively. On March 7, 2012, Apple discontinued the 32 GB and 64 GB configurations and assigned new order numbers of MC954LL/A and MC989LL/A for the black and white 16 GB configurations, respectively.
    Apple iPad 2 (Wi-Fi/GSM/GPS AT&T) 16, 32, 64 GB
    The Wi-Fi/GSM/GPS iPad 2 configurations are assigned model number A1396.
    MC773LL/A is the original order number for the 16 GB configuration in black. The 32 GB configuration in black is assigned MC774LL/A and the 64 GB configuration in black is assigned MC775LL/A. The original 16 GB, 32 GB and 64 GB configurations in white are assigned MC982LL/A, MC983LL/A, and MC984LL/A, respectively. On March 7, 2012, Apple discontinued the 32 GB and 64 GB configurations and assigned new order numbers of MC957LL/A and MC992LL/A for the black and white 16 GB configurations, respectively.
    Apple iPad 2 (Wi-Fi/CDMA/GPS Verizon) 16, 32, 64 GB
    The Wi-Fi/CDMA/GPS iPad 2 configurations are assigned model number A1397.
    MC755LL/A is the original order number for the 16 GB configuration in black. The 32 GB configuration in black is assigned MC763LL/A and the 64 GB configuration in black is assigned MC764LL/A. The original 16 GB, 32 GB and 64 GB configurations in white are assigned MC985LL/A, MC986LL/A, and MC987LL/A, respectively. On March 7, 2012, Apple discontinued the 32 GB and 64 GB configurations and assigned new order numbers of MC755LL/A and MC985LL/A for the black and white 16 GB configurations, respectively.
    Apple iPad 3rd Gen (Wi-Fi Only) 16, 32, 64 GB
    The Wi-Fi Only iPad 3 configurations are assigned model number A1416
    MC705LL/A refers to the 16 GB configuration in black. The 32 GB and 64 GB configurations in black are MC706LL/A and MC707LL/A, respectively. The 16 GB, 32 GB and 64 GB configurations in white are MD328LL/A, MD329LL/A, and MD330LL/A, respectively.
    Apple iPad 3rd Gen (Wi-Fi/4G LTE AT&T/GPS) 16, 32, 64 GB
    The Wi-Fi/4G LTE AT&T/GPS iPad 3 configurations are assigned model number A1430
    MD366LL/A refers to the 16 GB configuration in black. The 32 GB and 64 GB configurations in black are MD367LL/A and MD368LL/A, respectively. The 16 GB, 32 GB and 64 GB configurations in white are MD369LL/A, MD370LL/A and MD371LL/A, respectively
    Apple iPad 3rd Gen (Wi-Fi/4G LTE Verizon/GPS) 16, 32, 64 GB
    The Wi-Fi/4G LTE Verizon/GPS iPad 3 configurations are assigned model number A1403
    MC733LL/A refers to the 16 GB configuration in black. The 32 GB and 64 GB configurations in black are MC744LL/A and MC756LL/A, respectively. The 16 GB, 32 GB and 64 GB configurations in white are MD363LL/A, MD364LL/A, and MD365LL/A, respectively.
     Cheers, Tom

  • HT4061 how to fix the iPad with screen freeze.

    My iPad wont go back the screen the way it should be, it just like its freeze up the screen, could someone any idea to fix it.

    Give it a reset. Hold down the sleep and home buttons for about 20 seconds or so. You should see  a black screen, then the silver apple as it reboots.

  • How to enable a disabled iPad?

    my brother entered the wrong password on my iPad and it got diabled and it says to connect to itunes. But the computer i have synced the ipad to is not working and i have no idea how to enable my iPad. Does anybody know what i can do for this?

    FORCE IPAD INTO RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.

Maybe you are looking for