HT4061 my ipad air is in recovery mode and it is not starting.I pressed the main key when connected to my computer but there was no response
My ipad has gone in recovery mode when I tried to upgrade my system software.it showed a loading bar and then turned off and never started.i tried to turn it on by pressing the home key and start button simultaneously but there was no response.i even connected it to the itunes but there was no response by the ipad
RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. If you did not do step 4 properly, start all over again.
Similar Messages
-
I tried updating to iso 8.0.2 and now my iPad is stuck in recovery mode and will not do anything. it will not reset.
RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary. -
My IPad is stuck in recovery mode and now ITunes will not recognize it, it just gives me this long error message. What do I do, I've uninstalled and reinstalled ITunes.
Check USB connections
Related errors: 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650, 2000, 2001, 2002, 2005, 2006, 2009, 4000, 4005, 4013, 4014, 4016, “invalid response,” and being prompted to restore again after a restore completes.
If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
To narrow down the issue, you can also change up your hardware:
Use another USB cable.
Plug your cable into a different USB port on your computer.
Try a different dock connector (or no dock).
Add (or remove) a USB hub between your device and computer.
Connect your computer directly to your Internet source, with no routers, hubs, or switches.
If you checked your connections and are still seeing the error message, check for hardware issues.
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support. -
My ipad 4 is in recovery mode and says connect to itunes, but when i connect to itunes it says nothing. but in the device driver properties on my computer it says my ipad is in recovery mode. what should i do?
please help!See: http://support.apple.com/kb/HT1808 to restore the phone using Recovery Mode. You will lose all content on the phone. This is the only way to bypass the lock screen if you don't have the last computer the phone was synced to.
-
TS3694 Ipad is stuck in recovery mode and can not advance after attempted IOS 7 update
After attempting to upload IOS 7 for ipad the Ipad locked up in recovery mode and I get the 3194 error message
I'm getting the same message, and I have had to restore my iPad and lost all my settings!
-
Hi,
my phone is in recovery mode and wont restore. instead i receive the error message 1604. i have used alternative usb cables and am at a loss. has anyone else had this problem?Hi there hstear93,
You may find the information in the article below helpful.
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
-Griff W. -
My ipod touch 4 is stuck in recovery mode and i do not know what to do help me
my ipod touch 4 is stuck in recovery mode and i do not know what to do help me
Connect the iPod to your computer and restore via iTunes
iTunes: Restoring iOS software -
My iphone is stuck in recovery mode and itunes will not recognize my phone. I've tried pretty much every trick i can and i still do not know what to do. Someone please help me
I've done all of these, even trying a different USB port, and still, nothing. This is really confusing. Windows 8.1 said something to do with USB malfunction or something and nothing works. I need to restore my iPhone quickly and nothing has happened. My cable is not genuine Apple product. iTunes makes the noise that it makes when I connect the device, but it doesn't say 'iPhone is in recovery mode' or even say 'iPhone' in the corner. I am really fed up and would really appreciate a response.
Thanks,
Nathan. -
help me
My iPhone is in recovery mode and I do not see it on my laptop and on iTunes. Moreover, I can not turn it off and when I try it comes up all the time in the recovery mode.Hey Yan Heng,
Thanks for the question. It sounds like your iOS device is not recognized in iTunes for Windows, while in recovery mode. The following resource may help to resolve your issue. While you should run through each step, the specific information related to your symptom is outlined in Step 5 (If the device is not recognized while in Recovery Mode).
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Thanks,
Matt M. -
I have a iPhone 4 in recovery mode and it will not restore to factory settings.
I have a iphone 4 in recovery mode and it will not restore to factory settings. I get the error message error 21 and 2001. What can I do? I have tried all the steps.
Alextails998 wrote:
I have tried all the steps.
All what steps?
Did you go through the troubleshooting information here: http://support.apple.com/kb/TS3694?viewlocale=en_US&locale=en_US
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support.
and
Check USB connections
Related errors: 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650, 2000, 2001, 2002, 2005, 2006, 2009, 4000, 4005, 4013, 4014, 4016, “invalid response,” and being prompted to restore again after a restore completes.
If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
To narrow down the issue, you can also change up your hardware:
Use another USB cable.
Plug your cable into a different USB port on your computer.
Try a different dock connector (or no dock).
Add (or remove) a USB hub between your device and computer.
Connect your computer directly to your Internet source, with no routers, hubs, or switches.
If you checked your connections and are still seeing the error message, check for hardware issues.
If so, then it's a hardware problem. Make an appointment at the genius bar and get it replaced. Based on the "it was water damaged", I think it's a safe bet that it's toast. -
Hi, I have an iphone 5s went into recovery mode and reset does not clear up the problem, How to slove?
imansoheili wrote:
Hi, I have an iphone 5s went into recovery mode ...
Once the Device is asking to be Restored with iTunes... it is too late to save anything...
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps...
After you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766 -
IPad Air stuck in recovery mode!
Tried to update my iPad Air to iOS 8 this afternoon. Plugged into my brand new Macbook Air (about one month old), backed up to iTunes. Clicked to begin the update and install, left the room.
Came back to find the iPad Air in recovery mode (iTunes logo and lightning cable on the screen). iTunes reporting that it has detected an iPad in recovery mode and needs to restore. Since I have a backup already, I go ahead and click on Restore iPad, and then Restore and Update (my only option besides Cancel).
The progress window gets all the way to "Restoring iPad Software" and the progress bar starts to climb, but then I get the error message:
"The iPad "iPad" could not be restored. An unknown error occurred (9)."
I've repeated this process many times, usually the error occurs right at the beginning of the progress bar, but one time it almost got to the end before giving me the error message.
I read up on Error 9 and it says it may be something amiss with my security software. I have not installed any antivirus or firewall software. My firewall is off and always has been. Like I said, this is a pretty new Macbook Air, I've installed very few programs on it (Crashplan, Dropbox, Google Drive, Lightroom).
Any thoughts on what to do? It's completely frustrating. My iPad's been bricked. ;(Hi jzn_omg,
If you are having issues with the update and now restore of your iPad Air, you may find the troubleshooting steps outlined in the following articles helpful:
Resolve iOS update and restore errors in iTunes
Resolve iOS update and restore errors
Regards,
- Brenden -
When I downloaded (on PC) the new 5 it crashed my iPad 2. I worked for two days to get it to stop the malfuction, went to the apple store for four hours, iPad crashed again, got a new one, new iPad crashed when I tried to restore my back up. Down loaded iTunes to an employees computer, I was able to restore iPad to factory settings but my itunes account is on my office computer and now I am afraid to plug it into my computer. I did delete the back up as maybe that is currupt and making it crash??? Any body know about this?
This is Linda again. The new iPad actually as not restored on my employees computer. I thought it was working. Message said the device is in recovery mode and can not be restored. I have been at the Apple store for a total of 6 hours and on the phone with support for at least 4 hours. And now the replacement has crashed??? Has this happened to any one else?
-
IPad 2 went in Recovery Mode and I don't want to lose my data
Well, hello.
I have a big problem with my iPad2. From the begining: I wanted to update the iOS to 7.1.2. The progress bar appeared and I left it like that. When I returned, it showed me that I have to connect the device to iTunes. When I did this, it said that I have to restore it. The big problem is that I don't have any back-up of my iPad. I had, but my old laptop broke and I can't open it anymore. So I got a new laptop (Windows 8) and never connected the iPad to it, only now, when it is in Recovery Mode and... I tried to hold the Home+Wake up button both pressed in the same time, but still no change: the Apple logo appears only for a few seconds and it goes back to the Recovery Mode screen. I also downloaded TinyUmbrella from here: http://tinyumbrella.en.lo4d.com/ but nothing happened (it appeared something like TinyUmbrella: Verifying libraries, reticualting something). I also contacted the service in my country, but they said that nothing can be done, I have to restore it and, by this, erase all the data on it. Please, is there any way in which I can save the data? I'm more than desparateYes, I know... I discovered now that I have saved the photos I wanted from it long time ago (for the same reasons, i didn't wanted to lose them). So I'm kind of saved. Also it has been like crap because the laptop where I had my backups is as dead as can be. That was the moment when I panicked. From now on... I'll back-up it everyday. Thank you a lot!
-
My iPad is stuck in recovery mode, and wont stay turned off in order to use redsnow.
Alright so my iPad is stuck in recovery mode. I did some research and arrived at redsnow to fix the problem. In order to use redsnow's recovery fix option I have to power down my iPad. When I hold the sleep button though, no "slide to power off" appears, the screen just goes black then reboots into recovery mode 3 or 4 seconds later. Restarting it via holding the sleep and home buttons doesn't do anything. How do I get it to stay powered down? Any advice would be greatly appreciated.
I believe I may have used the wrong terminology. My iPad screen looks identical to the picture shown in the link, which is what I reffered to as Recovery Mode. I was looking for a way to return to normal functionality, without having to restore my iPad. I have never backed up this iPad and would prefer not to lose any information on it. If this is impossible then I will just restore it and carry on.
My main issue with restoring it is that I don't want to lose the pictures on it. If the restore doesn't erase the pictures, then I apologize for wasting your time and will be restoring it immediatly. However if I will lose the pictures than I'd prefer any other method of exiting this screen.
Maybe you are looking for
-
I was transfering photos from an external hard disk. While doing this somehow or another I created another library. I have an additional icon on my desktop. I tried to put it in the trash but then it deletes iphoto from the computer. I just would lik
-
FAQ: How can I make money in the App Store the easy way?
Suppose I have an app, like a game. It's not very good, I didn't really invest anything, there are a lot better ones out there but I want to make money with it. Are there ways I can do this? Q: Can I pay an "agency" in India, Russia, China or here in
-
Calling a java class in a JSP file
Hello, I have a jsp file in which I call a java class. I work with Tomcat 4.0.1 If I modify the java class and then I execute my JSP, it still be the old version of my class that is executed. I don't understand why since if I creates a main function
-
List Manager based on LOV returning values with missing spaces
I am using a list manager based on a pop up lov, in this case it is a list of supplier names. When the pop-up list is shown the values are displayed as expected, with all spaces intact. When I click the supplier name, and then click Add to add to the
-
So is there a fix for this Time Zone bug?
apple, is there a fix to this Time Zone bug in Calendar?