HT4106 the "Accessory unavailable the attached accessory uses too much power" any suggestions ? it is an Olympus FE camera

Useing the camera connection with the USB cable the ipad says "Accessory unavailable the attached accessory uses too much power, the camera is an Olympus fe.

It depends on the camera, but some have a special mode for offloading photos but not trying to charge the camera through the USB port. For others, you may have to pull out the SD card (if that's what it uses) and use the Lightning to SD card reader instead.
Maybe if you told us what camera you are connecting, somebody here with the same model can give you more specific information.

Similar Messages

  • When I plug in my Olympus TG 820 to my iPad2 a message pops up warning me that the attached device uses too much power. Is there a way around this?

    When I plug in my Olympus TG 820 to my iPad2 a message pops up warning me that the attached device uses too much power. Is there a way around this?

    1. Turn off iPad
    2. Connect camera to iPad
    3. Turn on power of camera
    4. Turn on iPad

  • I bought a camera connection kit , while connecting my camera (Samsung ex1) , I got this message from my iPad "my attached accessories using too much power "

    I bought a camera connection kit but fail to connect to my iPad . My iPad prompt me that my attached device using too much power ! I got no problem using the SD connecting kit. My camera is Samsung EX1 , pls advise

    Do your cameras support Picture Transfer Protocol (PTP) and/or USB Mass Storage Device Protocol (http://support.apple.com/kb/HT4106), and if so do you need to change a camera menu setting in order to enable it ?

  • HT4101 When connecting my camera to my IPad mini via lightniing to usb camera adapter,I get "The attached accessory uses too much power" .Any solutions?

    When I connect my Ipad mini to my camera via lightning to usb camera adapter all i get is a message "The attached accessory uses too much power."Any solutions

    It depends on the camera, but some have a special mode for offloading photos but not trying to charge the camera through the USB port. For others, you may have to pull out the SD card (if that's what it uses) and use the Lightning to SD card reader instead.
    Maybe if you told us what camera you are connecting, somebody here with the same model can give you more specific information.

  • Error msg 'attached accessory uses too much power' ??!

    WOW...HELP!!
    I get an error message:  'attached device uses too much power' virtually every time I attach ANYTHING.  Really?  Is this related to my distressingly sophisticated cyber-stalker- from- ****?  All I want to do is download some pics from my camera, for heaven's sake!  As a bonus, it would be cool if the apps I've purchased would actually function; scratch that - if they'd just show up in the apps list in my settings, even...that would be progress!
    I love Apple; my issues are NOT the result of the product, nor a lack of patience (and kindness) on Apple's part.  However, I refuse to accept 'statistically impossible error' as my lot in life...especially not as the result of some idiot stalker.
    BUT....
    I am woefully outclassed by this hacker jack***
    HELP!

    I get an error message:  'attached device uses too much power' virtually every time I attach ANYTHING.
    What are you trying to attach?
    As a bonus, it would be cool if the apps I've purchased would actually function; scratch that - if they'd just show up in the apps list in my settings, even...that would be progress!
    If there are no user settings in the app, it will not show up in Settings since there is nothing you can set.

  • To upload photos from my pc onto my ipad using a usb stick. I bought a camera connector kit and tried placing the usb stick onto one of the white square adaptors, stuck it into the ipad2 and I got 'the device uses too much power'' message. Pls help.

    I am not very familiar with the ipad2. I wished to transfer some photos from my pc (not an apple pc but that is the only one I have) to my ipad2 as I thought it would be easier to cull them, edit, crop etc to create albums for our recent trip (the photos are already on the pc and no longer on the camera memory card). When I place the usb stick on the adaptor and stick it onto the Ipad2 I keep getting 'device uses too much power/ requires too much power' message. I read somewhere on the internet that a usb hub could be used to solve the issue but that did not work either. What am I doing wrong? Is there actually a way around this problem. If not why does apple sell this product for Ipad users at all?
    Thank you for any help/ solution you can offer.
    Regards

    I'd ask that on the iPad forum.
    https://discussions.apple.com/community/ipad

  • HT4101 When I connect using the USB version I get a message on the ipad saying "the attached accessory uses too much power. What can I do?

    Ipad2 Camera Connection Kit
    When I connect using the USB option I get a screen on the ipad which says "Accessory Unavailable. The attached accessory uses too much power"
    What should I do please?
    David

    I believe your camera uses a micro SD card. The CCK accepts the full size SD card. Do you have a SD card adapter to plug the micro into?
     Cheers, Tom

  • I can no longer download photos to my ipad with the camera attachment. the message says thats its using too much power. i have a 100% charge and i used it before and it worked fine.

    I can no longer upload photos with the camera attachment. I am getting an error saying the device uses too much power. I have used the device before. Is there anything that can be done to fix this problem?

    You don't actually say what the problem is, but maybe this can help:
    USB and Firewire information:
    http://support.apple.com/kb/HT1151?viewlocale=en_US
    http://support.apple.com/kb/HT4049?viewlocale=en_US

  • HT4106 unplug the device using too much power to re-enable USB devices

    iPad min cannot be changred, it shows
    unplug the device using too much power to re-enable USB devices

    Try unplugging it. Give your iPad a reset by holding down the sleep and home keys for about 20 seconds (until it reboots) then try again.

  • Camera Connection Kit - Accessory uses too much power

    I am trying to import photos from my Kodak EasyShare M873 via the USB connector from the CCK. About a quarter of the way through the import, the iPad disconnects and states, "The attached accessory is using too much power". Is anyone else getting this. I suppose I could just remove the SD card from the camera everytime I want to import. But then what is the point of having the USB adaptor if the iPad can't handle connecting to a semi-low quality consumer camera?

    The USB cable is great if the battery is full and you don't have a ton of photos, or if the camera either has photos in its "built-in" memory or doesn't use SD.
    PERSONALLY I'm glad they included both, but plan to use only the SD adapter on trips.
    Doug
    PS: It might be interesting, though probably camera-specific, to compare transfers times both ways...

  • HT4101 It says accessory will use too much power.......what do I do?

    I have bought the lightning to USB camera adapter for my new iPad but it is saying the accessory uses too much power? What do I do? Please help

    Is the adapter an Apple product or 3rd party?
    Try this first - Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
     Cheers, Tom

  • On my MacBook Pro with Retina Display, Why does the "USB Devices Disabled Unplug the device using too much power to re-enable USB devices" keep coming up after I unplugged the usb device?

    On my MacBook Pro with Retina Display 15", that I purchased a few weeks ago, started coming up with the following message on my desktop:
    "USB Devices Disabled Unplug the device using too much power to re-enable USB devices".
    I unplugged the device and the message still keeps coming up.
    This is what I have done so far to troubleshoot:
    I shut down the laptop. When booting up I pressed the command+option+p+r at the same time. It comes up with a menu to reinstall OSX, Get help online, Run Disk Utility, etc. I choose the disk utility and repair the disk and then restarted.
    The message keeps popping up and I can't seem to get rid of it. Why does the message keep popping up even though I don't have any devices hooked up to the laptop at all? Any help to reenable my usb ports and get rid of the messaage would be helpful.

    I talked to Apple Support and we at least stopped the bleeding, a little bit. These are the troubleshooting steps I did before I contacted Apple Support:
    1. Reinstalled OSX
    2. Restore the last known good Time Machine Backup.
    This did not fix my issue, so I called Apple Support and they told me this:
    1. Turn Power off.
    2. Wait 15 seconds.
    3. Plug in Magsafe adapter.
    4. Wait 15 seconds.
    5. Hold down the Shift+Option+Power Button for 20-30 seconds.
    6. Turn Power back on.
    Ok, this stopped the bleeding a little, but as soon as I plugged in a Apple USB Superdrive
    and a Apple Mini Displayport to VGA Adapter. This "USB Devices Disabled" pop-up pops up like every 30 minutes now. At least, it is not constantly popping up after I close it, so I guess it will do for the temporary. Going to contact Apple support, later, though to see what else can be done.

  • Why does my Macbook pro said "unplug the device using too much power to re-enable USB devices" when i plug in my iphone's charger to connect my phone with the mac?

    my iphone 5's charger is not working anymore with the mac or the normal plug in neither, i dont know why. whenever i plug in my mac, i have to twist the charger a little and my mac said "USB Devices Disabled: Unplug the device using too much power to re-enable USB devices". of course it cant connect with the itunes in my mac, but somehow it still syncs the music to my iphone... i don't understand why. please help me thanks!

    try resetting the ipad,or change the cable ,it woould work 

  • I can no longer charge my iPhone5 through either of my macbook pros. I get the error message that a USB device is using too much power. Can anyone help?

    I can no longer charge my iPhone5 through either of my macbook pros. I get the error message that a USB device is using too much power. Can anyone help?

    I reconnected the original powered hub that I thought probably caused the problem and this time it shut down the whole computer. When I rebooted everything now works perfectly. The system reset. I tried another powered hub and it didn't have the same effect so the old one is heading for the bin and with fingers crossed all systems are now working perfectly. Trying to reset PRAM or reset the SMC didn't work but causing the same power issue did. Thanks for your input though. It did get me to think what was the original cause.
    Cheers
    Guy

  • I made an extra backup on a USB device and now I can't get it back because "the device uses too much power". Why didn't it a few weeks ago and how can I use the device anyway?

    because "it uses too much power"
    I did'nt get that message a few weeks ago when I used Snow Leopard and now I can't approach the files I saved on the external disk.
    Question 1: How do I solve the problem? (Without going back to Snow Leopard)
    Q2: Why this parential supervision by Apple?

    riks1105 wrote:
    because "it uses too much power"
    I did'nt get that message a few weeks ago when I used Snow Leopard and now I can't approach the files I saved on the external disk.
    Question 1: How do I solve the problem? (Without going back to Snow Leopard)
    Q2: Why this parential supervision by Apple?
    Get a powered hub
    USB is cranky, you're not the first (probably not the last) to have this happen.

Maybe you are looking for