HT4145 how to connect the i pod to airport extreme

I am trying to figure out how to connect to my airport extreme from my ipod- anyone who can give me a stepby step answer?
I am not sure which operating system it is...
Thanks!

If the AirPort Extreme is allowing other devices to connect, it is not the issue.
Follow the iOS Troubleshooting Guide for Wi-Fi Networks and Connections
http://support.apple.com/kb/TS1398
You will be better served to post in the iPod support area for questions about the iPod.  Post here:
iPod

Similar Messages

  • How to connect a hard drive on Airport Extreme (second edition)

    how to connect a hard drive on Airport Extreme (second edition)? Does it need a special format? It is now fromat on FAT32, but i don't see it ??

    The USB port your Mac is high powered. The port on the AirPort Extreme is not.
    So, it tends to be borderline as far as its ability to supply sufficient power to a hard drive...even if the hard drive has its own power supply.
    Often, users...including me....need to use a powered USB hub when they attach any drive to the USB port on the AirPort Extreme.
    You might want to give that a try. Double check to make sure that the drive is formatted in FAT32 as well, since Windows NTFS or exFAT will not work with the AirPort Extreme.
    Powering down and restarting the entire network.....modem first, then router, etc.....is something that you would always want to do after any change or addition to a network.

  • How to extend the range of my Airport Extreme network by adding an Airport Express

    How to extend the range of my Airport Extreme network by adding an Airport Express?

    You have to make sure that the AirPort Express is in Factory Default Settings. If it is straight out of the box, it is ready to be configured.
    The instructions that I will provide are for using AirPort Utility 6.0, which you have.
    Locate the Express in the same room as the AirPort Extreme for the configuration. Power it up and allow a full minute for the Express to display a blinking amber light.
    Make sure that the wireless is turned on your Mac
    Open AirPort Utility 6.0 and look at the small rectangle in the upper left hand corner of the display. It should now read something like "Other AirPort Base Stations (1)"
    Click on the rectangle, and then click on the AirPort Express xxxxxx listing
    AirPort Utility will take a minute or two to analyze the settings on your network and then suggest that  the Express be configured to "Extend" your wireless network.
    Edit the Base Station name to your liking, then click Next in the lower right hand corner
    Allow a full minute or two let AirPort Utility do its work
    When you see Setup Complete, click Done at the lower right of the window.
    Now move the AirPort Express to a location that is approximately half way between the AirPort Extreme and the area that needs more wireless coverage.
    You should be in business.

  • How to connect a Philips fidelio to airport extreme?

    I just purchased an Airport Extreme Time capsule. I cannot connect my Philips fidelio AD7000W to the network. There are no WPS button on the Airport Extreme. There is a WPS printer connection option in the Aiport app menu option but nothing for sound system. Anyone knows how to make the connection ?

    Instructions on how to connect the Fidelio to a non-WPS supported router is covered in the User Guide starting on page 13. On step 4 you would enter the specifics for your wireless network. That would be the network name, the wireless security type & wireless password. You will also want to choose the DHCP mode as enabled for these speakers.

  • How to disable the wireless section of Airport Extreme Base Station?

    Is it possible to disable the wireless section of Airport Extreme Base Station?
    It is because I do not want to have any high frequency radio signal which may be dangerous for small baby (no such proof for the moment, however).
    Anyone using the new Airport Extreme Base Station please check and help.
    Thanks!!

    I think you are a little too concerned. Just for the sake of how to, here it is.
    go to manual set up, airport, wireless, wireless mode, and then choose off.
    good luck.

  • How to access the pendrive on my Airport Extreme via my iPhone 3GS?

    I connected a pendrive on my Airport Extreme.
    After connecting my Mac to the Airport Extreme it showed the pendrive.
    But when i connected my iPhone to the Extreme it did not show the pendrive.
    Is there any app or way that I can view or acces my pendrive on my iPhone?

    Try an App like FileBrowser from the App Store.

  • How to connect a ADSL router to AirPort Extreme?

    Hallo,
    my local internet service provider forces all costumers to use their modem/router to connect to the Internet using a DSL connection.
    I have one external public IP (v4) and the router has an editable IP for the LAN set to 192.168.1.1 .
    The ISP router can act as DHCP server and NAT; I can disable the DHCP.
    What I would like to do is connect it to the Airport Extreme WAN port and give all the control to the Airport extreme: I want to use his DHCP server, NAT, port forwarding etc.
    My problem is that I am able to have Internet connection only if the ISP router has DHCP control and Airport Extreme is set to Bridge mode.
    In this configuration, in the Airport Internet configuration panel, the connection is set to Ethernet, IPv4 is using DHCP, Airport IP is 192.168.1.133 and the ISP router has 192.168.1.1 . I also have the DNS IPs set to the ones suggested by the ISP and Bridge mode.
    In this way it works: all computers can share Internet connection.
    What I am trying to do is:
    - disable DHCP in the ISP router;
    - in the Airport extreme Internet panel I choose to manually setup IPv4 and I type the same vales it is getting when set to DHCP mode: 192.168.1.133 for the Base and 192.168.1.1 for the router using the ISP dns and I select Share pubblic IP. In the DHCP panel I choose 10.0.1 class.
    I save changes and... I got that Internet is no working anymore and I cannot access the ISP router control panel.
    Does anybody have suggestion about things to try to not use ISP router DHCP or configuration changes I could try?
    Thanks in advance for any help about it!

    Thanks for the reply,
    at the end it seems that my airport extreme works too BUT with an error message saying "double NAT" and the front led turned to yellow. I have ignored such error because things seems to work and so the led color goes to green.
    What I had to do here is:
    - set previous router to IP 192.168.1.1
    - turn off DHCP on my previous router;
    - leave on the NAPT (NAT) service on previous router and set it with start and stop address to the same IP I am using for the Airport Extreme (192.168.1.100);
    - open all ports and services on previous router by faking the mac address of the Computer's NIC I was using to configure router. I say faking because previous router wants to know for which computer the ports have to be open, so I had to use the same mac address of the Airport extreme. I cannot type it, previous router will get it automatically when configuring it.
    - on the Airport Extreme, Internet side, I had to manually configure Internet options using Ethernet mode: I set the IP 192.168.1.100 for the Airport base. Then I have enabled DHCP on class 10.0.1.x .
    Airport extreme seems to work with all features now, I hope that "double NAT" warning will not create any trouble. Anybody knows about that?

  • My ipad 3 is frozen on the plug into itunes page. I have tried to follow advice I have found on these pages but I don't know how to connect the ipad to my mac (there is no usb port on an ipad). If anyone could help it would be appreciated.

    My ipad 3 is frozen on the plug into itunes page - it won't turn off or on - just stuck. I have tried to follow advice I have found on these pages but I don't know how to connect the ipad to my mac (the advice is to connect ipad to mac and there is no usb port on an ipad). If anyone could help it would be appreciated. Going nuts.

    I think you should probably also read the iPad User Guide. You didn't say what version of iOS your iPad is running, so here's the links to both the iOS 6 and iOS 7 (PDF) versions:
    iPad User Guide for iOS 6
    iPad User Guide for iOS 7

  • How to connect an apple tv to an enterprise network with a username and a password?   I need to use it over my university's wifi. theres no option to enter username and password. how to connect the apple tv to such enterprise network?

    How to connect an apple tv to an enterprise network with a username and a password?
    I need to use it over my university's wifi. theres no option to enter username and password. how to connect the apple tv to such enterprise network?

    Contact the University's IT dept, they may be able to set something up on the network to allow the ATV to connect without the need for a user name/password.

  • Does any body know how to connect the fingerprint scanner using jmf is it p

    Hai,
    I am not getting how to connect the fingerprint scanner how we can do it is it possible for device independent application
    If any body knows anything about this please mail me its very urgent for me
    hope u will be able to tell me something about this .
    Regards
    K Naveen Kumar

    Hi,
    Fingerprint scanners are not popular enough devices to be supported by Java yet. There's no general API or Java interface for it.
    Each manufacturer of a fingerprint device will probably just ship their own drivers or SDKs. More than likely DLL's, so you'd need to write some JNI to call them.
    If you want to allow your application to work with multiple devices, you will have to design it to do that. Ie. write a general "Fingerprint" interface, and write a class which implements that interface for each device you want to support.
    Eg.
    public interface FingerPrintAPI
         public void initialiseScanner ( )
                throws MyScannerException;
         public byte[] getFingerPrint ( )
                throws MyScannerException;
         public double getMatchProbability ( byte[] fingerprint1, byte[] fingerprint2 )
                throws MyScannerException;
         public void closeScanner ( )
                throws MyScannerException;
    }I haven't used a fingerprint device at all, but that's how I would approach it.
    regards,
    Owen

  • How do Connect the JAUD on a 915P Combo

    How do Connect the JAUD on a 915P Combo MB
    I have a case with a front panel. The wires are named:
    2 wires "SPK R" (2 connecters on the same wire) Red wire
    2 wires "SPK L" (2 connecters on the same wire) White wire
    1 wire "GND" (Grund) Black wire
    1 wire "M IN" (Microphone) Green wire
    1 wire "M Bias" (Microphone) Blue wire

    not sure ive looked at the main board manual  and my new blower case has the same front audio hook ups but i was not able to locate the connections  useing the mainboard manual that came with my main board im still wondering about how to connect the front audio  my self !  915p combo-fr

  • I need to know how to access the book pod in robohelp 8/

    i need to know how to access the book pod in robohelp 8/

    Hi there
    Actually, by my count there are at least five ways to coax books into the TOC
    From the menu, Click File > New > Book.
    Type the keyboard shortcut of Ctrl+Shift+B.
    Right-click the pod and choose New > Book.
    Click the New Book icon in the pod toolbar.
    If you have organized your project using folders, you may automatically create a TOC based on the file structure and each folder becomes a book. There are also multiple ways to automatically create the TOC. One is by right-clicking the TOC pod. Another is by clicking an icon in the pod toolbar and another is by clicking the Tools menu.
    Cheers... Rick
    Helpful and Handy Links
    RoboHelp Wish Form/Bug Reporting Form
    Begin learning RoboHelp HTML 7 or 8 within the day - $24.95!
    Adobe Certified RoboHelp HTML Training
    SorcerStone Blog
    RoboHelp eBooks

  • HT4262 How can I connect 6 computers simultaneously to Airport extreme?

    I have tried troubleshooting several ways and the some computers work and others don't. How can I connect 6 wireless computers to Airport Extreme?

    Matt
    Is it possible to speak on the phone?  The situation is so convoluted it might be easier to help me get back on track in person. When I first had this issue I got on an apple site that had a chat room in which I typed in my problem.  After several missives back and forth, the apple technician asked for my number and we spoke on the phone. The technician walked me through rebooting the actual airport plug (as opposed to the router box) and got me up and running. Do you know how I can relocate that chat site for technical support?
    Thanks
    David

  • My westel modem (that I rent from my phone provider) quit working with the internet.  My airport extreme seems to be working from the dsl (phone) connection through the westel, then through the ethernet cabled to the airport extreme.  Do I need the modem?

    My westel modem (that I rent from my phone provider) quit working with the internet.  My airport extreme seems to be working from the dsl (phone) connection through the westel, then through the ethernet cabled to the airport extreme.  Do I need the modem?  Is the ethernet route less efficent that going throught the internet connection?  If I don't need the westel modem; how do I make the dsl conection to the pone port in the wall?  Thanks for help on this!

    Ok, so are you saying that your Internet is or isn't working?  Does it work if you plug your computer directly into your computer and bypass the router (make sure you power cycle the modem when you do this)?  If it is working this way, then a new modem isn't going to solve a problem with your Internet not working.  If it is going slow (try running a speedtest) then you need to call your phone company to have them take a look at why your Internet is slow.  If it runs fine this way and then slows back down when you go back through your router there is something else going on.  Try unplugging both the modem and the router, let the modem fully sign back in and connect to the Internet, after it gets signed in, plug your router in, and then after it boots up fully, try running the speedtest again...See if that helps any?  Sometimes it's just an IP conflict that happens when the dynamic IP that is assigned by your Internet Service Provider changes and the change doesn't flow smoothly.

  • How to set up Guest Network, while Airport Extreme is connected to Satellite Receiver

    How to set up Guest Network, while Airport Extreme is connected to Satellite Receiver?

    Depending on how you have your AirPort Extreme configured to work with the satellite receiver, it may or may not be possible to enable the Guest Network function.
    We will need to check some settings on your Mac or PC, but in order to do that, we need to know what operating system you are using on your computer.
    If you have a Mac, click the Apple icon in the upper left corner of the computer screen, then click About This Mac. Post back with the OS X Version number that you see there.

Maybe you are looking for