HT4241 Macbook-Air connect to TV direct HDMI / Won't Play

I have my macbook pro connected to my tv via HDMI. Nothing playing? Just a static pic...How do I get the video thats playing on the macbook air on the tv?

That's extended desktop mode. Just grab the app and drag it off the right side of the MB screen. It will appear on the TV.
Visit the System Preferences > Displays > Arrangement tab for other options.
Regards,
Captfred

Similar Messages

My Macbook Air connects to ATV at home but not at work

My Macbook Air connects at home over a Time Machine network to my apple tv just fine (including airplay); when at work on a non-apple wifi network both computer and apple tv connect but cannot see each other. As I would like to stream video to the work ATV via airplay, this is a problem... Any ideas?

Hello Allan Robinson,
After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning AirPlay:
iOS: Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS4215
Try the following suggestions:
Ensure that other devices are not trying to stream to the same Apple TV at the same time.
Ensure that your Wi-Fi router is set up with the recommended settings for the best performance.
Certain external devices, such as microwave ovens and baby monitors, may interfere with a Wi-Fi network. Try moving or disabling these devices.
If possible, try to locate your Wi-Fi router in the same room as your iOS device and Apple TV.
If your wireless and wired networks are the same, try connecting your Apple TV to the router via Ethernet instead of Wi-Fi.
If the Wi-Fi router has an external antenna, check to see that is it connected properly and in good condition.
Use the Wi-Fi network troubleshooting guide to resolve interference and other issues.
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

MacBook Air connected to projector won't display dvd in superdrive, but plays on macBook Air screen.

MacBook Air connected to projector won't display the dvd in the superdrive, but it is playing on the MacBook Air screen.
When dvd is ejected, MB A screen appears on the big screen through the projector. What do I need to do to get the training dvd showing on the screen?
Thanks

Power off the router. Unplug it from the wall. Wait a while.
Plug it back to the wall. Power the router on. Wait until all the lights are lit properly. It will take a while.
Restart the computer.
Start up in Safe Mode.
http://support.apple.com/kb/PH11212?viewlocale=en_US
Deselect proxies if selected.
System Preference > Network > Advanced > Proxies Tab
Uncheck “Auto Proxy Discovery”.
Click OK, Apply.

Been trying to use an external memory card reader with my macbook air- connecting via usb port, air does not recognize device nor the microSD card from my gopro - help

Been trying to use an external memory card reader with my macbook air… connecting via usb port, air does not recognize device nor the microSD card from my gopro … help

Some external ones do not work with the Mac's although most do. There are some driver compadibility issues with Mavericks, so I would wait for an update.

My MacBook Air is stuck in iPhoto and won't let me log out it says its downloading pics to the library but it not - can anyone help me to escape out of this?

My MacBook Air is stuck in iPhoto and won't let me log out it says it is downloading pics into the library but it is not - can anyone help me escape out of iPhoto?

Apple menu ==> force quit
Post back if you have trouble after quitting and rebooting your MBA
LN

New (3mo) macbook air screen goes black and sometimes won't come back on after I unplug it from the power cord. Any ideas why it is doing this? Sometimes I have to hold power button for 10 seconds for it to shut off then back on.

New (3mo) macbook air screen goes black and sometimes won't come back on after I unplug it from the power cord. Any ideas why it is doing this? Sometimes I have to hold power button for 10 seconds for it to shut off then back on. Sometimes holding the power button for a second is enough for it to come back on.

I took it to the Genius Bar, and they identified it as a hardware issue. Just got it back today. Parts replaced were:
620-5629 Display Module — Symptom: Distored/blurred/focus video issue
605-3284 Top Case with Keyboard — Symptom: specific key(s) do not work
So far so good. I'd suggest taking it in and not trying to work around it — it's a rare hardware issue (given the number of threads about it) and should be replaced.

My 3 year old MacBook Pro, with OS 10.7.1, won't play movie DVDs I burned on Panther. Why?

My 3 year old MacBook Pro, with OS 10.7.1, won't play movie DVDs I burned on Panther.
Why?

But to answer your question, you might be able to create a ISO of the DVD and burn that to a new DVD.
Insert your DVD.
Open /Applications/Utilities/Disk Utility.app.
In the left side of the window, select the “DVD”.
Click “New Image” from the Disk Utility toolbar and select where you want to save the temporary image. For “Image Format”, choose “DVD/CD master” and for “Encryption”, choose “none”.
The image extension in the “Save As” box will be .cdr (this is what you want) — click “Save”.
Once the temporary image is created, it will show up on the left side of the Disk Utility window. Select it.
Insert a blank DVD (I prefer Verbatim discs).
Click “Burn” from the Disk Utility toolbar.
Another problem could be that you burned the DVD using a codec that your new machine doesn't have.
Install Perian, VLC and Flip4Mac, that combination will play anything.
Also install Flash for web content and Silverlight for Netflix.
http://flashbuilder.eu/flash-player-version.html

Cannot connect Macbook Air to Samsung TV via HDMI

Hello, I have been completely unable to get my Macbook Air (13-inch, Mid 2011, running OS X 10.9.1) to connect to my new Samsung TV (UN32EH5000F) I feel like I have tried everything I can think of, have spent hours now looking for a solution online. I also consulted Samsung tech support, who were not helpful in that they insisted the problem is with my Macbook (because the HDMI port on the TV works when I hook up my DVD player).
I'm trying to connect my Macbook Air to the TV using a Mini DisplayPort (Thunderbolt Compatible) to HDMI cable. I have gotten the connection to work on my LG monitor (via the same HDMI cable), but this did require some switching back and forth between sources before it would appear as an external monitor on my Mac and doesn’t seem to work reliably. Sometimes I can get the LG monitor to work as an external display over HDMI and sometimes I can’t.
I have also gotten the TV to work ONCE on my Macbook Pro (15-inch, Late 2008, running 10.9) by plugging the cable into the Mini DisplayPort while the computer was asleep. I have not been able to replicate this in many tries since that first time.
When I insert either end of the cable (either into the TV or the Macbook Air), the screen flashes as if recognizing that the cable is plugged in, but the TV always says "No Signal."
I have also tried:
Every possible combination of plugging in cables
Shutting down my Mac and the TV and rebooting
Switching the source on my TV back and forth
Plugging the HDMI cable into both ports on the TV
Changing the name of the HDMI source on my TV (to available options like "PC", "DVI", "DVI PC", etc.)
Battery power and AC adaptor
Resetting the PRAM and the SMC
Using the Option button in Display preferences to click “Detect Displays”
Any help would be appreciated!

For Netflix viewing, youre going the LONG way around to watch same using your Macbook
Get an AppleTV which you can use for Netflix, and Airplay and watching tons of free content.
I use the same for netflix and Airplay of video over wifi.
Best $100 gadget money can buy

Windows 8.1 on Macbook Air connecting to Time Capsule

I have installed Windows 8.1 on a separate partition of my MacBook Air. My Time Capsule (2 TB) is visible when I boot to iOS X, however, when I boot to WIndows, it doesn't show in the Network devices list even though the MacBook Air is connected to the Internet through the Time Capsule's wireless network. Does anyone have any suggestions of how to make the Time Capsule available under WIndows? I have turned on Network Discovery and file sharing in Windows.
Thanks for your time.

It is very helpful to install airport utility for windows.
Although rather out of date it adds bonjour for windows and other small apps which help.
Then in standard Windows Explorer, type the TC IP address directly into address bar.. thusly.
\\10.0.1.1
Now you will need to find out the IP of the TC.. that should now be available in the airport utility you have just installed.
If it refuses to open the issue is firewall .. turn it off.. or it is network is set to work or public location not home.. reset it to home.

Question about macbook air connecting to the tv

Hi there,
I have a macbook air and a non-HDMI tv I recently procured from Goodwill. What do I need to buy in terms of cords, etc... to connect my Mac to my tv?
Thanks!

You should also ask this in the MacBook Air forum. This is the forum for the white and black plastic MacBooks that were discontinued in 2010. You should also post this question there to increase your chances of getting an answer.
https://discussions.apple.com/community/notebooks/macbook_air

Macbook Air connects to network fine but will not connect to internet?

I am staying with someone away from home and cannot use my Macbook Air (OSX 10.9.4) with the internet. They have a Comcast network and all other devices including my iPhone, connect with no problems. I have connected to the network and it works initially (loading a web page or retrieving email) but almost immediately the internet stops working and pages freeze trying to load. The wifi shows no problems but internet connection is not working for both email and safari
I have cleared the network info and set up again, reset the router, restarted my computer and other trouble shooting. I have been able to connect to the same network by tethering my phone as well but cannot use the network directly.
Everything indicates that there the network connection is fine but but no internet, please help!

Connect to the problem network. Double-click anywhere in the line of text below on this page to select it, then copy it to the Clipboard by pressing the key combination command-C:
www.google.com
Launch the Network Utility application.
Step 1
Select the Lookup tab and paste into the address field by pressing command-V. Then press return. Post the output that appears below – the text, please, not a screenshot.
Step 2
Select the Ping tab and do the same. Please enter the same input as you did in Step 1. Don't use the output of Step 1 as input to Step 2.
Important Note
Some web browsers and mail clients will automatically convert a domain name such as "www.example.com" to a clickable URL, such as http://www.example.com. That will interfere with the test. If necessary, edit the input in the Network Utility window to remove any added characters.

Macbook Air: connecting Canon Office All-In-One PIXMA MX330 printer

I purchased my Macbook Air a few months ago, and I selected theCanon Office All-In-One PIXMA MX330 printer to go along with it. I have tried to install the printer a few times in various ways. Initially, I used my Macbook Air superdrive to attempt to load my new printer with the included disk. However, installation requires that the printer be connected to the Macbook via USB. Since the superdrive was occupying my only USB, I tried to connect my printer wirelessly with another computer. The laptop I used was not a Mac, and I simply could not get his computer to recognize the disk for my Macbook. So I tried something else; I borrowed my school libraries USB splitter in a last attempt to connect them both to my Macbook Air at the same time. However the superdrive does not react when not directly connected to the computer...
In short, I cannot find a way to connect my Canon Office All-In-One PIXMA MX330 printer to my Macbook Air.
Help?

Connect the SuperDrive to the computer, use the Disk Utility in the /Applications/Utilities/ folder to create an image of the installation disk, disconnect the SuperDrive, plug in the printer, and install the software from the image.
(44558)

MacBook Air connected to a Laserjet Pro MFP but not printing

Hi, I am trying to print from an HP LaserJet Pro MFP M-125a which is connected to a MacBook Air via a USB cable. The software has been downloaded and the print job window is always showing as if it is in the process of printing the print job given but no printing is issued and the print job is seen as done. Can you please tell me what's wrong why the print outs are not coming out?
This question was solved.
View Solution.

Hi @Lilium ,
I see that you are having issues printing through the USB connection. I would really like to be able to help you resolve this issue.
Did you download and install the full software solution or run the Apple Upates?
Check the driver name that is installed for the printer. Make sure it shows just the printer's name.
Click the Apple menu and then click System Preferences. Click Printers & Scanners, highlight the printer name on the left side and on the right side of the screen it should show the printer's name. (LaserJet Pro MFP M125a )
If the full printer name isn't listed correctly, delete it and add the printer name back in from the list. Click the - sign to delete the driver and then click the + sign to add the driver, might have to click the drop down to select the printer's name to add it in.
How is the printer name listed?
If the issue persists, please try the following steps:
Repair the Disk Permissions on the Mac:
Close all applications.
On the Apple menu bar, click Go, click Applications and then click Utilities.
Double-click Disk Utility.
Highlight your hard drive/partition on the left.
Click Verify and then Repair Disk Permissions.
Restart the computer..
Reset the Printing System:
Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol.
Click the Apple icon and then click System Preferences.
Click Printers & Scanners.
Right-click (or Ctrl +click) in the left white side panel, then click Reset printing system.
Click OK to confirm the reset.
Type the correct Name and Password.
Click OK to reset the printing system.
Then click the + sign to add the driver, highlight the printer. (you might have to click the drop down to select the printer's name) Then click on the Add button.
Try printing again.
If you need further assistance, just let me know.
Have a great day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Macbook Air (mid 2012) Thunderbolt to HDMI Stopped working

Hey Guys,
I have searched this issue and have found several threads some 50+ pages long but I could not find a soluition. I currently have a macbook air 13" mid 2012 model.
Problem: I was using a thunderbolt to HDMI cable to watch movies on my SONY Bravia tv and it was working fine one day and after I updated my software to mac OS X 10.7.5 it stopped working. All i get on my TV is "no signal" and the screen on my MBA starts to flash blue every now and then.
I took it into the genius bar and they plugged it in to their system and it seemed to work, so the guy said to get a new cord.
I ordered a new cord and tried it at home and its still not working. After searching the forums I see that alot of others seem to be having the same issues and I am pretty sure its related to a software issue seen in the thread below.
https://discussions.apple.com/thread/3196192?start=75&tstart=0
Anyone have a similar issue and found a fix??

A new Mac is in warranty for 1 year from the date of purchase. Why not use it?
You may have to take the computer to the Apple store to have it checked out.
All hardware related issues should be brought to the attention of Apple.

Problem with MacBook Air connecting to Epson Stylus sx600fw wirelessly

Hi
I have been trying to set up my new Macbook Air with Epson Stylus sx600fw. Previously this printer was being used via USB with a PC. I have set up the printer on macbook via USB, but under the advice of online resources, erased that and began trying to set it up for wifi use. The printer cannot be found in the Print & Scan section of settings, and when i enter it in manually with IP address, it can find the software to install but gets stuck and says "Unable to verify the printer on your network". After further research i have tried to Ping the printer, which does not work. One thing that i notice is that the Subnet Mask is different than the apple default...for the printer it is 255.255.0.0, where for apple it is 255.255.255.0 but i dont know how to change this
Any advice for where it might be getting stuck or what I can do?
thanks!!!

Welcome to the forums @lesleglreglpegl ,
I have a few suggestions for you that might help with the connection problem you're having with connecting your OJ J4680 to your Mac.
Here are the steps:
Mac OS X: How to reset the printing system
Repair disk permissions
Restart the Mac
Re-add the printer (do not use the AirPrint driver)
Good luck to you, have a great Monday
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

HT4241 Macbook-Air connect to TV direct HDMI / Won't Play

Similar Messages

Maybe you are looking for