HT4245 when trying facetime i get not connected to wifi.
cannot get facetime to work without being connected to wifi. why?
if i have an active phone account it should work..help?
Does your wireless carrier support Facetime over cellular data connection?
Similar Messages
-
I have been unable to use FaceTime on my iPad2 when I only have a 3G connection. I get a message saying " You do are not
connected to wifi." Does it only work with wifi?"I have been unable to use FaceTime on my iPad2 when I only have a 3G connection"
Correct.
"I get a message saying " You do are not connected to wifi." Does it only work with wifi?"
Yes. -
I get not connected to internet when trying to open TLS 1.0, what can I do to correct problem
I get not connected to internet when tring to open TLS 1.0 site, what can I do to correct problem?
'''[https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode Start Firefox in Safe Mode]''' {web link}
While you are in safe mode;
Type '''about:preferences#advanced'''<Enter> in the address bar.
Under '''Advanced,''' Select '''General.'''
Look for and turn off '''Use Hardware Acceleration'''.
Poke around safe web sites. Are there any problems?
Then restart.
Some added toolbar and anti-virus add-ons are known to cause
Firefox issues. '''Disable All of them.''' -
Hi. I have an iPhone 4 with iOS7 and no data plan. When I am not connect to wifi I don't receive iMessages, but then when I do connect to wifi I get the messages telling me they were sent earlier. Is there any thing I can do to fix it? I don't remember how long this has been happening but it is very frustrating. Any suggestions would be great! Thanks!!!
If you don't have a cellular data plan, then why are you expecting that you will have an active internet connection unless you are connected to wi-fi?
iMessages require either wi-fi or a cellular data connection. -
hi just got a gift of an ipod touch model MD720LLA with operating system iOS7.1.2
I get the following error message when trying to sync "could not be synced because the sync session failed to finish"
what could be the problem
have also uninstalled and re installed itunes
thanks
<Re-Titled By Host>Mac Unidentified Developer Issue
Here's how to open apps that apple should not be blocking:
http://www.imore.com/how-open-apps-unidentified-developer-os-x-mountain-lion -
getting error message could not activate cellular data network when trying to access the internet without using wifi. what do i need to do? i have already restore the phone.
contact your phone carrier as they handle cellular network.
-
getting not connected to internat message when i back page or fill out forms
If you are using Safari, go to the Safari menu bar click Safari / Preferences then select the Autofill tab.
Click the Edit button next to: Other forms. Click Remove All.
Back to the menu bar, click Safari / Empty Cache.
Restart your Mac. -
've tried everything and all of the sudden my macbook air will not let me use my PhotoBooth or FaceTime it says not connected to camera? help!?
iSight camera failure after OS X 10.9 Mavericks update
-
my imac will not connect to wifi what so ever. i have tried 3 different routers and all my other apple devices work fine. when i take it to the genius bar it seems to work with apples instore wifi. thus leading the "geniuses" to say nothing is wrong.
Back up all data before making any changes.
Step 1
Take all the applicable steps in this support article.
Step 2
If you're running OS X 10.8.4 or later, run Wireless Diagnostics and take the remedial steps suggested in the summary that appears, if any. The program also generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
Step 3
If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. Continue if you find that Wi-Fi is faster with Bluetooth disabled.
From that same menu, select Open Bluetooth Preferences. If the box labeled Discoverable is checked, uncheck it. Click the Advanced button, and in the sheet that opens, uncheck the top three boxes, if any are checked. Click OK. Enable Bluetooth and test again.
If the application called "Bluetooth Setup Assistant" is running, quit it.
Step 4
This step will erase all your settings in the Network preference pane. Make a note of them before you begin, and recreate them afterwards. It may be helpful to take screenshots of the preference pane.
Triple-click the line below on this page to select it:
/Library/Preferences/SystemConfiguration
Right-click or control-click the highlighted line and select
Services ▹ Reveal
from the contextual menu.* A folder should open with an item named "SystemConfiguration" selected. Move the selected item to the Trash. You may be prompted for your administrator password.
*If you don't see the contextual menu item, copy the selected text to the Clipboard (command-C). In the Finder, select
Go ▹ Go to Folder...
from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
Step 5
Reset the System Management Controller.
Step 6
Make a "Genius" appointment at an Apple Store, or go to another authorized service center.
Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
*An SSD doesn't need to be zeroed. -
I cannot upgrade my IPad 2 with IOS.70, the download appeared to be complete but while it was verifing a "not connected to WIFI" message appeared yet IPad was connected and working. Not sure what is wrong, even tried to turn off Advast VPN thinking that was the issue but cannot complete upgrade.
try resetting your phone by turning it off and back on again. Also try resetting your network settings under Settings > General > Reset > Reset Network Settings.
-
I have an iphone 4 and trying to upgrade ios 6, downloaded the version and when trying to install get an error that i need internet, i have internet of course... please help...
C Mawle wrote:
Thanks. I have followed all the instructions as recommended and nothing has worked so it looks like the restore/update may have been interrupted - would loss of internet connection do this?
Yes it would, possibly even brick it.
Have successfully connected my ipod nano with iTunes so looks like the device driver is working.
Can I use my ipod nano USB connector to check?
It is not much help to you, since the device that you need still not recognized.
Anyway looks like I may have to swallow the loss of data. Have set-up a call for tomorrow with Apple support so will wait until after this before doing the factory restore!
Good luck, but if you expect miracle from that call good luck again. -
While calling on Facetime , it does not connect , it says connection lost
While i calling on facetime, it does not connect , it says connection lost all the time
After trying everything, here,s what worked to me: go to settings - facetime, and when it asks how you want to be reached on facetime, uncheck the icloud email option. Hope it works!
-
I cannot update my ipad2 to ios5. Updating through iTunes on pc Windows Vista, Error message reads "cannot connect to iPad Software Update Server. Tried resetting network settings, still not connecting. Tried updating iTunes, still not connecting.
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Cheers, Tom -
I need to fix my ipod and i don't know how, i am hoping that if i leave it alone over night that it will fix itself,
its on the lock screen and i cant do anything with the screen, i tried restarting it and it didnt work, so because i restarted it, it is not connected to wifi.
please help.
will getting a new screen help? or is there an easier, less expensive way?Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
When trying to update getting (error surle error domain error-1100). It started yesterday, any help would be great. I have Mountain Lion 10.8.1 on a new macbook pro with retina display.
There are many people suffering from this problem right now (including me). It appears to be a server issue. Just wait and try checking for updates again tomorrow.
Some things I have heard indicate that this may be a regional problem, though what parts of the world are affected I don't know yet. A few people have been helped by deleting the following preference file (paste the path into the Go -> Go to Folder window in the Finder to locate it), though most have not:
~/Library/Preferences/com.apple.SoftwareUpdate.plist
Note that if you are trying to download iTunes 10.7, that can be found here:
http://support.apple.com/kb/DL1576
Also, note that there is no reason to be anxious to get it, as the only thing added in iTunes 10.7 is compatibility with iOS 6, which will not be available until the 19th, and the new iPhone, which will not be available until later as well. The new iTunes that was announced is iTunes 11, which is also not yet available.
Maybe you are looking for
-
Error ITS_TEMPLATE_NOT_FOUND when calling a function code from the web
Hi Experts, I have craeted a simple module pool program and a service for the same in SICF. The module pool has only one screen where I am giving the input to the two fieds 1. year 2. category. when I click on FIND button the result will appear on t
-
MI 7.1: Obtain SYNC_KEY from DB
Hi experts, I have a problem, i want obtain the SYNC_KEY from DB, but if i do the SELECT SYNC_KEY FROM table the SYNC_KEY appear: "001E4F1D754C1DDD8CC9420C1C8E587E", it has char, and should be only number. How can convert it? Thanks in advance,
-
Don't want ADC port/just 2 DVI's!!!
Sirs & Madams: Point me to a video/graphics card with 2 DVI ports. Sick of adaptors that don't work. Simply want 2 monitors for video editing. I have both and have spent WAY too much on quick fixes. New video card...2 DVI ports...NO ADC display ports
-
My E-Mail is going off the screen, Help!
I have a MacMini with Mail Version 2.1 (752/752.2) Very recently my e-mail both mine outgoing and my incoming mail have gone off the screen and I cannot read. Suggestions? Questions for me? Please help.
-
Selection screen variant for report
Hi, Can we restrict the selection screen variants for reports by user? For example my report is ZREPORT. Different users can save variants for the report. When they choose a variant for executing the report, they would like to see only the variants t