HT4259 Does Airport Express extended network inherits wifi time restrictions?

Hello:
I have created a network with my Airport Extreme and I've set up some wifi access time restrictions based on mac addresses. Now I want to extend this network adding an Airport Express at the living room. Everything went smooth but I'd like to know if I need to set up the restrictions at the Express or does it inherit them from the Extreme.
Thanks!

Inherits from the Extreme as they are determined by the connected devices to the Wi-Fi.

Similar Messages

Iphone will not connect to airport express extended network - macbook and ipad will - Help

Iphone will not connect to airport express extended network - macbook and ipad will without problems.
iphone will connect to base station no problems, I've restored settings and started again but still the same, the iphone picked up the network for the last couple of months, but not now ?

I'm having the same issue. My AExpress used to give a good signal strength on the far side of the house extending he network created by my Extreme. However, I've noticed lately that my iPhone does not receive the same strong signal it once did. AE has a green light, I've rebooted it, and my Extreme but there is no change in signal strength. Other than the green light, how can I tell if the Express is working if I don't get a good network signal?

Time Capsule & Airport Express Extended Network loses connection!

OK, so I am an Apple virgin of 2 months experience, after many many years with Windows based PCs, so please be patient and gentle with me. Sorry about the long explanation.....
My set-up comprises of a Time Capsule, which is connected to the Internet via a NetGear ASDL modem. Both pieces of equipment are situated in my wife's office on the first floor of our house. My office is on the ground floor, where I have a 27" iMac and an Airport Express which is connected to a printer via the USB port. The Airport Express is sited about 10 feet from the iMac.
All software and firmware are lastest versions - TC v7.5, AX v7.4.2 & Airport Utility v5.5.
For the past 2 months, I have only been using the AX to print wirelessly and the set-up has worked faultlessly.
Earlier this week, I decided change the configuration to extend the network to allow me to use my laptop & iPhone in areas of the ground floor where I had no signal. I followed the online instructions and first changed the TC to check the box to 'allow this network to be extended', after updating the configuration successfully I moved to the AX. Here I changed the wireless mode to 'Extend a wireless network', selected the network name and checked the 'Allow wireless clients' box. This also updated successfully.
Everything ran correctly and the range of the network was greatly increased.......great, job done...not!
After about 3 hours the iMac lost the connection and the TC disappeared from the Airport Utility pane and refused to reappear. I checked but also couldn't connect or see any network on the laptop or iPhone, so have dismissed a fault with the iMac. I finally got things back up after doing a power reset of the TC, but after a few hours same problem occurred, and occurred and occurred. By clicking the Airport Utility icon on the top right of the screen and following the prompts from 'no Internet connection', I can at least get things up and working without a power reset of the TC, but the connection still drops after 2-5 hours each time.
My first call to Apple Support led to a full reset and re-config of both the TC and AX, setting the extended network up as I had done originally. The only difference was an iMac reset (alt/cmd P&R on power up) and changing the 2.4Ghz channel from 1 to 11. This had no affect and the connection drop-out problem continued.
My second call to Apple Support led to me being passed to a Level 2 Techie, who first suggested that I tried disabling the Guest Network - tried it, and it made no difference. I was then told to try a WDS network, which whilst not losing connection, is slower and has less range than the original extended network and frankly sounds a cop-out.
Has anyone had a similar problem, anyone solved the problems, can anyone offer any help or advice please.. I'd appreciate any input....thanks.

Similar problem here. Cable Modem (Moto SB6120)->AEBS (802.11n dual-band)>AX (802.11n) for wireless connection to MacBook Pro running Mac OS X 10.6.2. AEBS configured as dual-band: 801.11a/n at 5GHZ and 801.11b/g/n at 2.4 GHZ. AX configured to wirelessly extend the AEBS 5GHz 802.11a/n network. I am able to run on the extended 5GHz network (via AX) for varying lengths of time, until the internet connection dies. When this occurs, I am able to switch over to the 2.4GHz network to get back online. Solution up until now has been to unplug the AX, then plug it back in. After the AX restarts, I am able to hop back onto its 5GHz signal and get to the internet. However, the internet connection on this band will drop again after some time.
I was on the phone with Apple Support twice in the past week to get this resolved, but no joy. Senior Advisor seemed to think that my AX was working properly, and that that the problem could be with my AEBS -- perhaps the 5GHz antenna might be bad in my AEBS? Seems odd to me, since both my AEBS and AX are less than 2 months old...
I just read the post from LocoDoc and decided to see if I could replicate the problem. Sure enough, when I am connected to the internet via my AX extended 5GHz network signal and a Time Machine backup starts, the internet connection quits. Only recourse is to restart the AX. Note that I do not experience this problem with Time Machine while connected wirelessly straight to the AEBS 5GHz signal. Only when I am connected to the "extended" signal via the AX.

Airport Express extending network needs to be restarted daily

I'm having a really annoying problem with my Airport network. Here's the configuration:
Den: Latest generation simultaneous Dual-Band Airport Extreme
Living Room: older 802.11g Airport Express used only for AirPlay
Office: older 802.11n Airport Express wired to the Airport Extreme via ethernet, extending network
Hallway: 802.11n Airport Express wirelessly joining and extending network
Bedroom: Latest generation simultaneous Dual-Band Airport Express wirelessly joining and extending network
I have an older house which is not terribly big but the radio-opaque walls make it difficult to propogate wireless, thus the need for so many units.
It all works pretty well except for my bedroom Airport Express (simultaneous Dual-Band). On a daily basis it will lose connection with the network or go so painfull slowly that it's pointless. The only solution is to do a reboot of the unit which works temporarily (good connection / good speeds) My son likes to watch Roku in our bedroom and that Roku uses the WiFi that the Airport Express should provide. Needless to say troubleshooting wifi when your 3 year old is crying because he can't get 30 seconds of streaming before the signal craps out is not fun. Anybody have any suggestions???

"Hard reset" the bedroom Extreme to preclude the possibility that some corrupted internal parameter is limiting its performance. Consider doing that with all of them. They will subsequently need to be reconfigured.
Configure the den Extreme to provide a unique name for its 5 GHz network, and ensure all the devices capable of using it are using it, and not 2.4 GHz. Find out what your Roku is capable of using.
The key to solving problems, if your challenging requirements are solvable, is to start with as simple an installation as possible, then progressively add to it. Find out the maximum usable range of your den's Extreme in both 2.4 and 5 GHz bands, then position any devices used to "wirelessly extend" its signal roughly half the distance to that Extreme - not a different base station. The ideal location for the Roku's Express may not necessarily be in the bedroom.
Run speed tests each time and make sure you are not trying to "extend" a weak signal. "Extending" a weak signal makes it stronger, but no faster that what it receives.
That's all you can do.
... I thought "N" networks minimized that problem.
You're right about that.
The thing is I get decent wireless reception in the bedroom WITHOUT the express plugged in.
I wonder if those devices are really using the Express you think they are. That's the problem with multiple base stations. There are ways of addressing this question but not with the current AirPort Utility version.

IPhone 5 won't connect to Airport Express extended network

I've just bought a new Airport Express and have succesfully set it up to extend my exisiting network through the Time Capsule. Now when I'm in the area where i need to connect my iPhone 5 to the new airport express, I'm not seeing it in my wifi settings on the iPhone. My understanding was, the express would create a an extended wifi area that any device could connect to. Is this correct?

It should but you probably have it in the wrong mode.. it is joining a wireless network not extending.
Go back to the airport utility and change the setup of the express.. make sure it is extend not join.
You may need to reset it to factory and start over.

Multiple AirPort Express - Extending Networks

Hello
I have been at it all morning trying to get it to work, no luck thus far.
The network I have at the moment consists of
Adsl modem > (cat5) Airport Extreme > (wirelessly extended by) Airport Express 1F > (wirelessly extended by) Airport Express 2F
I am running this network in a 3 storey building
Ground floor - Airport Extreme
First floor - Airport Express 1F
Second floor - Airport Express 2F
The Express on the first floor picks up the network created by the Extreme on ground floor and successfully extends it to the second floor.
This is the part that is giving me a world of trouble.
The Express on the Second floor picks up the network being extended by the Express on the First floor, but fails to extend it.
The green light is on and everything, settings are correct (identical to 1F).
Though when I am on the second floor and start to venture away from the limits of 1F, the 2F doesn't seem to boost the signal or extend the network, after walking 5 meters away I lose connection to the network.
Can anyone help?

As I have 3 Airport Express' all up, would I theoretically set it up so that 2F would "Join a wireless network" > allow ethernet clients then plug the third Express (3F) to 2F. Then setting 3F up to create a wireless network? clients would have to reconnect between the two, but it would be a temporary fix until I can have a network cable installed to connect the Extreme with 2F.
You could leave AirPort Express 2F in the "extend a wireless network" configuration because the ethernet port is enabled in this type of setup.
Then connect an ethernet cable to 3F from 2F and configure 3F as a "bridge" (Connection Sharing = Off (Bridge Mode)) to "create a wireless network" using the exact same wireless network name, security and password as the main router. Then, computers would not have to reconnect as they move around the house.
If you configured the network this way, you would not need to connect AirPort Express 3F all the way back to the AirPort Extreme. But, you would have better bandwidth if you did connect it directly to the AirPort Extreme.
Message was edited by: Bob Timmons

Airport express extend range of wifi

How do I extend the wifi signal in my house with the 2nd gen Airport Express? I have a non-Apple router (Orange) and an old Mac Mini. Thanks in advance. Sang

hello
i want to buy the TP LINKhttp://www.amazon.com/gp/product/B00E98O7GC/ref=ox_sc_act_title_4?ie=UTF8&psc=1& smid=ATVPDKIKX0DER
and i have a question
i have no longe the normal router. i have the Apple Airport Express ( and I am going to buy another airport express to even more get a better wifi range)
my question is. how can i set the TP link with the airpot express?
regards

AirPort Express - extend network and/or AirTunes - one or both ?

I would like use my second AE to extend my existing AE network AND wire it to my stereo to use the AirTunes feature. No trouble setting it up for AirTunes but can't seen to get it to extend the network. Any tips about how I can get both features to perform as advertised?

If you need more wireless coverage, you can use the WDS configuration method for a "mix" of older "b/g" and newer "n" devices.
The big downsides here are that WDS operates only at "g" wireless, so you lose any faster "n" capability on the network...and...the bandwidth of the entire network will be cut in half. So, in effect you will have a bit more wireless coverage, but it will be a "g" wireless network running at half speed.
I don't recommend this, but if you want to try, post back for more details.

Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range

Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range.

You cannot extend wifi from a different brand router..
Only apple to apple.
But the apple router does not have to be the main router.. it can be in bridge.. as long as it is creating a wireless network it will work fine.

Problem with airport express extending wifi from extreme

My setup is an airport extreme wired to the internet with two iMacs connected by wire and an airport express to extend wifi from the extreme to the further parts of my house. When originally installed about a year ago this arrangement worked perfectly, but I noticed a few weeks ago that neither my iphone, ipad, nor my MBP 13" is connecting to the aitport express anymore and the network extension is not working as intended.
Last night I investigated the isue and found that the express is connected wirelessly to my extreme because when I wired my MBP to the express and turned off the wireless connection it could still reach the internet. But, even with the express sitting plugged in next to my iPhone I could not get it to connect to the express - it always uses the extreme and while I'm in range there is no problem. The problem is that my house is old and the wals tend to cause problems with reception and I can't get wifi in the garden and some parts of the house.
I have the express and the extreme configured to allow access only by the client macs that I have provided and it looks like the two devices share this information when they are in extend mode (but not sure about that). When I set up the system I added the aitports mac addresses to the approved list in the access control screen, which seemed to be necessary then though I removed them (the airport mac addresses) fromt he list last night to see what effect this had and biefly the airport did connect to my MBP. But after returning it to its location where it usually is I have not been able to reconnect to it.
In brief; I have an airport express extending an airport extreme wifi, it used to work, but now all wifi clients will only connect to the master. I have a suspicion that a recent airport update has caused this (both airports are up-to-date) but can't be sure. I have the express correctly configured to extend the wifi of the extreme as it was originally working.
One thing I have noticed - I had the express set to use a fixed IP by setting 'static' in the internet screen - this is not the current setting (it's reverted to DHCP) and I cannot force it to update to and remain set to static.
Does anyone know how I can restore the correct functioning of the express as an extension of the wifi network?
Thanks
Damon

Perform the Factory Default Reset one more time. Hold the reset button until the amber light has been blinking rapidly for 8-10 seconds before you release the reset button
Run the setup wizard, and wait for screen similar to this to appear, then click on Other Options:
Select the Add to an existing network option, then click Next and follow the prompts.
If you are still having difficulty, try running the setup utility on an iPhone or iPad, since Yosemite has a number of bugs in the setup process.

Can AirPort Express Extend non-Airport WiFi?

The description of the AirPort Express at:
http://www.apple.com/airportexpress/features/sharing.html
has this footnote: "AirPort Express can extend the range only of an AirPort Extreme or AirPort Express wireless network.”
Is this literally true or just a legalistic disclaimer. Is it possible to make AE work with a Netgear or Linksys router's WiFi? Or not?
One of our user group members does not have a stable connection between her iBook G4 and a Comcast router by Netgear. This is in a townhouse with two floors between them.

Is this literally true or just a legalistic disclaimer. Is it possible to make AE work with a Netgear or Linksys router's WiFi? Or not?
Pretty much. There are only a very very few non-AirPorts that are WDS-compatible. One is the Linksys WRT54G ... and only with a specific firmware version. You can do a quick Google-search, using terms like: Linksys AirPort WDS, and find at least a dozen references.
But, this is not really any different with the other vendors as most of their equipment, if extend-able, only do so with their own.

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

Hello Hornet12,
Indeed, iTunes 10.2 or later will be required to utilize AirPlay.
Using AirPlay
http://support.apple.com/kb/HT4437
AirPlay requirements and capabilities
To get full AirPlay features, make sure your AirPlay-enabled devices are running the latest software updates. The table below identifies minimum AirPlay requirements and capabilities:
Stream content from
Requirement
Notes
iPad
iOS 4.3 or later.1
From the Videos, iPod, Photos, Music, and YouTube apps on iOS devices, stream videos, music, and photos to an Apple TV (2nd and 3rd generation), or stream music to an AirPort Express or compatible third-party device.
With iOS 4.3 and later, you can also stream video and audio from a website or a third-party app installed on your iOS device if the developer for the app or website has added AirPlay functionality.
iPhone (3GS or later)
iPod touch
(2nd generation or later)
Computer
iTunes 10.2 or later.
Stream videos and music from your iTunes library to an Apple TV (2nd and 3rd generation), or music to an AirPort Express or compatible third-party device.
Apple TV
Apple TV software version 5.1 or later.
Stream music from your Apple TV to another Apple TV (2nd and 3rd generation), to an AirPort Express or compatible third-party device.
Cheers,
Allen

Does a second airport express extend the wireless signal from the first?

After a long search on his forum and not finding an answer, this is my question:
I have a Time Capsule connected to a Speedtouch router/modem. The Time Capsule has its own network. Because of the distances in my house, I use an Airport Express to extend the wireless range for my MBP. This doesn't seem to be enough to cover the whole distance (app. 35 meter) there is poor or no connection. So, my question is: can I use a second AE to extend the range even further? Will it pick up the signal from the first AE or do all the AE's in use need to connect with the Time Capsule?
The first AE is app. 12 meter from the TC.
many thanks,
Inge

Welcome to the discussions!
The answer is yes and no.
No, if you are using the "extend a wireless network" feature because each AirPort Express communicates directly to the Time Capsule, not to another AirPort Express. It's like the hub and spokes on a wheel. The Time Capsule is the hub and the Express devices are at the ends of the spokes. The devices at the ends of the spokes communicate directly to the hub, not to another spoke.
Yes, if you are using the "WDS" feature because this type of setup allows a "main", "relay", and "remote" device to be configured. But, there is a big penalty with this type of system:
o The network will operate at "g" wireless speeds only
o The bandwidth on the network will drop 50% for each "relay" or "remote" device. So, with two devices, the first cuts half of the bandwidth. The second devices cuts half again. So, you are down to only 25% of the original bandwidth.

Airport express extending wifi extremely slow

Hello,
I have a time capsule creating a wireless network and a airport express extending the wireless network.
When I'm connected to the time capsule I have around 12mbp of speed but when I am connected to the airport express I have around 0.2mbp
In the airport utility it says the connection is good she connected to the airport express.
Everything was working fine a few days ago.
I was reading the the forum that it may be interference from a neighbour and to change the channel but I can fine where to change the channel.
Is changing the channel the solution? How can I access where to change the channel?
Or is there another solution?
Anyone knows how to fix this speed problem in airport express?
Cheers
Francisco

What is the distance between the Time Capsule (TC) and the AirPort Express Base Station (AX)? Are they in the same room, different room, different floor from each other? If in different rooms/floors, what is the basic building material used in the walls/floors/ceilings?
It is important to understand that the AX can only extend the TC's wireless network at the same bandwidth that it receives it. If you are only getting around .2 Mbps at the AX, then either there is too much distance between routers or there is some form of Wi-Fi interference (other Wi-Fis or the builiding material) between them that is preventing the AX from getting a strong enough signal to extend.
Changing channels is one possible solution. You would do so using the AirPort Utility. If you are using version 5.x of that utility, you would change channels as follows: AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless tab > Channel. By default Channel is set to "Automatic." Click on the up/down arrow to the right of the Channel window to get the other channel options.
If this doesn't resolve the problem, please check out the following AirPort User Tip for details on how to best place each base station for maximum bandwidth in an extended network.

Trying to connect my airport express to my home WIFI

Hi,
I have been trying to connect a airport express to my home WIFI connection for the purpose of wirelessly transmitting itunes to my Alfresco area using my iphone as a remote.
The problem i currently have is that the airport does not seem to pick up my wireless broadband.
My router is a Netgear dgnd3700.
The procedure i followed so far is : 1. Reset the airport back to factory settings.
2. Plug the ethernet cable in and open airport utility.
3. Tick the circle saying " join existing network ". Here's the problem, my wireless network does not show up.
I can type in the name of my network and also the password but the airport is not picking up the signal .... i cant choose a network.
I can create a new network no worries and connect devices to it but that's not what i'm after. I'd like to join my existing network so i can transmit itunes to my amp.
I've gone through the discussion forum but can't find an answer. I have also tried to manually set up the connection .. same result.
Any help would be great ... i'm about to give up and think it was abad idea ....

If it is the old G version Express you cannot use 6.3 utility.
You must use the 5.6 utility.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.
For screen shots see this post.
https://discussions.apple.com/thread/4668746?tstart=0

HT4259 Does Airport Express extended network inherits wifi time restrictions?

Similar Messages

Maybe you are looking for