HT4367 Did a restore on a 3rd generation ATV thru iTunes but ATV wont power up. I changed battery on remote too. Any ideas?
Did a restore on a 3rd generation ATV thru iTunes but ATV wont power up. I changed battery on remote too. Any ideas?
Welcome to the Apple community.
Did you follow the following instructions exactly:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Source list, and then click Restore.
Similar Messages
-
My iphone suddenly stops working and asked for activation required. I did restore it thru itunes but it asks me to turn off "find my iphone". How can i disable "find my iphone" if i can open the iphone itself. please help me.
My iphone 5 suddenly stops working and asked for activation required. I did restore it thru itunes but it asks me to turn off "find my iphone". How can i disable "find my iphone" if i can't open the iphone itself. please help me.
-
IPod touch 3rd generation not accessing iTunes account through wifi.
I have a 3rd generation iPod touch with iOS 4.1. I currently have no computer so I download music directly through wifi. When I try to download music it asks for my iTunes password, and when I enter it the message pops up asking for the password again. It does this over and over. I am using the correct password and even changed my password just to be sure. The same thing happens when I try to redeem an iTunes card or view my account. Not sure if it matters but I've been doing this at 2 different Starbucks. Any ideas?
It sounds like this may be the fix:
http://support.apple.com/kb/TS3540
(Mac OS X v10.6 or later: iOS device not recognized in iTunes after restart) -
I just did a restore to my new iPhone 6 from iTunes and now my phone will not turn on at all. How do I get it to re-start?
Hi denise mfrompalatine,
If your iPhone won't turn on, try the steps in the resource below:
If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
https://support.apple.com/en-us/HT201412
Hope that helps ...
- Judy -
My iphone 4s is saying NO SERVICE.I tried to put it on airplane mode,tried to reset the network setting and also tried to restore my phone but none of the above things worked.Do you guys have any idea what should i do now?
Hi sunnylordz,
Thanks for using Apple Support Communities. Based on what you stated, it sounds like you have no service on the iPhone. It looks like you have already done some troubleshooting. There is one step you did not mention trying that i think is worth trying.
If you see No Service in the status bar of your iPhone or iPad - Apple Support
Remove the SIM card. If the SIM card is damaged, worn, or bent, or if it's too big or small for the SIM tray, contact your carrier for a new one. Then reinsert the SIM card.
Cheers,
Mario -
My ipod touch is stuck on a white screen and i did everything hold the home botton and sleep botton togher, but it wont respnd it is just stuck on the white flash scree HELP PLEASE!
- Let the battery fully drain. The charge for an hour and see what happens, Try resetting too:
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Connct to computer and restore if it shows in iTunes.
- You can try placing the iPod in recovery mode and then trying to restore. See:
iPhone and iPod touch: Unable to update or restore
- Also see:
iPod touch: Hardware troubleshooting
Frequenly the white scree is due to a hardware problem. -
I have had to put my ipod touch in Recovery Mode and tried to sync it with itunes but it wont restore itself. What can I do?
http://support.apple.com/kb/TS3694#error3194
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro 8G RAM 750G HD + OCZ Vertex 3 SSD Boot HD
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
In Memory of Steve Jobs -
Ipad won't start; trying to restore thru itunes, but get the message - can't restore because ipad is not set up. It was set up and has been in use for about a year. What do I do now?
I Have seen people report this issue when they try to sync their devices but in never seen it when trying to restore an unresponsive iPad. I would sguggest trying recovery mode now.
If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support
This procedure will totally erase the iPad so I hope that you have a backup that you can restore from....assuming that it works, that is. -
i down loaded ios 6 now my phone wont turn on it has been 2 days and it is really bugging me it keeps saying link to itunes but it wont link itunes asks me to restore the phone and i dont want to loose my info ps i have itunes 10.7
you must restore i would put in dfu mode if it isnt asking to restore when you plug it in
-
I cannot activate my phone to restore factory setting, I have tried through Itunes but receive the message the message that activation server is temporarily unavailable.
booner2@@@ wrote:
I cannot reactivate my phone, activation server is down, cannot get a response from you at Apple. Please respond.
And you're not going to get a response from Apple on this forum. Again, this is a user-to-user technical support forum.
To contact APPLE support, go to getsupport.apple.com. -
Hi i wanna restore my ipad 2 thru itunes but popup error 3194 what should i do now?
hi i wanna restore my ipad 2 thru itunes but popup error 3194 what should
Have you tried the troubleshooting for error 3194 on that page, including the 'This device is not eligible for the requested build' section towards the top of the page ?
-
My iPod touch was stolen.. and recovered.. but the kid that stole it cleared my iPod and "made it his own".. it has a password that makes me unable to use it. (He won't give up the password). I have tried to do the restore thru iTunes but the "note" from iTunes says it is unable to restore without the current password.. is there anyway around this... HELP !
You'll need to connect it to the iTunes library you normally sync it with and restore it. If iTunes asks you for this passcode before it will let you proceed, connect the iPod to iTunes in recovery mode instead using the instructions in this Apple support document.
iOS: Unable to update or restore
B-rock -
since upgrading ical on mac for .me account can't sync calanders with older generation itouch using 3.1.3os now calander on itouch generates blank screen...any ideas
Thank you for suggesting the link. it seems the problem was even simpler than I had thought had I read the FAQ link of the iCal/me upgrade notification ... Apple's latest version of iCal simply does not support versions of the iOS earlier than 4.2. The device I had been using was a first generation touch... Still working ... with out error in good condition despite having been to hades and back... But no longer supported by the newer versions of the iOS and the .ME ical application...
Another beautiful but orphaned device:-(. Like the absence of support for "ancient" apple operating systems, including their more interesting applications, it is simply no longer supported...one must move on to purchase new hardware and it's associated software to keep up with the evolving cloud os. The blank screen ical problem, on the touch, was corrected by performing the standard start up reboot procedure...with no loss of data and a return of the screen interface in the end. Again another example of the really outstanding past efforts to make robust system products. I will try to put my old touch to good use in its new " retirement" status ...use it some where else, like my original 128k Mac ( that still works as well!). Guess it is time to purchase a newer tool ;-)
Thanks again for taking the time to make the effort to assist -
did an update for my 4s now it tells me i need to connect to itunes but phone wont connect to itunes also i have got ios6 on my screen and thats all the phone will do
They will be gone from the iphone, but you should be syning all contacts to your computer regularly and should be importing all pics to your computer regularly, particularly before any update.
Have you failed to do this? -
HT4367 Unable to restore Apple TV 3rd Gen
The indicator on my Apple TV started blinking rapidly. Took the steps as per HT4367. Tried all steps to update thru I-Tunes. It downloads the update but then says firmware incompatible. Any ideas?
Hi daveledward,
Thanks for using Apple Support Communities. Based on what you stated, it sounds like you have a flashing light on the Apple TV. I would recommend that you read these articles, they may be helpful in troubleshooting your issue.
Apple TV: About the status light - Apple Support
Flashes quickly
Having issues. Try restarting or waking your Apple TV. If your Apple TV does not start up properly, you might need to reset the Apple TV or restore it to factory settings. See Apple TV (2nd and 3rd generation): Restoring your Apple TV. If this does not resolve the issue, refer to the Service FAQ for additional assistance.
Apple TV (2nd and 3rd generation): Restoring your Apple TV - Apple Support
Cheers,
Mario
Maybe you are looking for
-
How to make an index use in a query execution
Hi, I have the below query for which ename column has an index. As of my knowledge below queries 1st and 2st will not use index. Hence i used the 3rd statement and that too its not using the index. Finally i used the 4th query, but even the 4th query
-
Short Dump Error while loading master data.
Hello All, I am trying to load data from PSA to Info Object (0Material_Attr) via DTP, I am getting error and itu2019s giving the short dump. Runtime Errors UNCAUGHT_EXCEPTION Exception CX_RSR_X_MESSAGE. "UNCAUGHT_EXCEPTION" "CX_RSR_X_MESSAGE" "SAPLRR
-
I've done something (but not sure what!) to change the size of the icons on my desktop (plug in USB drive, harddisk, etc icons) they are all tiny - barely as large as a single letter in the text underneath the icon. I cannot see any setting to adjust
-
I'm going crazy! Setting up Airport Express to extend existing wireless net
Please help me, I'm going crazy! I am trying to set up my Airport Express as a "WDS remote/relay station" to bridge my existing BT HomeHub (the new black one) broadband wireless network to other wireless PCs, Playstation, etc located in other rooms o
-
Set waveform chart size to value 1000
Is there any possibility to set the size of waveform chart buffer to value >1000 in LabVIEW? Message Edited by Konigusko on 05-03-2006 09:40 AM