HT4437 Help with airplay and pioneer AV amp

Hi, I have a Pioneer 1326-k (Basically an Elite VSX 53). It is wired directly into my router. I can use airplay from the PC, But not from the Ipad (belongs to the kid, don't know what gen), Iphone (3GS), or the ipod (I am guessing 4 as we just bought it). I have the blue tooth adapter, and it works fine. The wireless control of the amp works fine as well (iControlAV2). Any help appreciated.
Ian

Not sure why your Pioneer receiver is unable to perform as a DHCP client, but adding the appropriate IP address information should be relatively straight-forward.
You can easily get the information using your iMac and going to: System Preferences > Network > Ethernet or AirPort depending on how your iMac connects to the network.
Here's an example from mine. Note: I'm using OS X Lion so it will look a bit different from yours.
For the Pioneer, the DHCP address = Router address; DNS = DNS Server, etc. However, DON'T use your iMac IP address for the IP address used by the Pioneer. The IP address you should use would be in the same subnet, BUT OUTSIDE of the DHCP server range of your router. By default, the AEBS, uses 10.0.1.2 thru 10.0.1.200 for these addresses. I would suggest using 10.0.1.210 for the Pioneer.

Similar Messages

Potential Problems with Airplay and Mountain Lion

Hey Everyone,
I recently purchased an Apple TV, and I tried to use Airplay with our Macbook Pros. Airplay would work with all of the iOS Devices, but when it came to using with the MBP, it would either show a black screen, or a frozen image of my screen. I called AppleCare, and the rep told me it was a problem with the AppleTV, so I returned it and bought a new one, and it did the same thing. I found out that the problem was occuring because of the type of router I was using. I have a dualband router, and I set everything on one band of the router. I decided to try to place the laptops on a different band, and that's all it took. My airplay now works flawlessly.
So, if you're having a problem with airplay, and you have a dualband router, try placing your computer & iOS devices on the opposite band, and it should work perfectly.
Hope this helps.
- Kaytie Walters

The VPN log looks like:
1      13:34:36.904 09/11/12 Sev=Warning/3
CM/0xA3100027
Adapter address 10.211.55.6 has changed or not detected. Current address(es): 10.98.70.169.
2      13:34:52.044 09/11/12 Sev=Warning/2
CVPND/0xA340000E
Failed to get adapter index.
3      13:35:07.044 09/11/12 Sev=Warning/2
CVPND/0xA340000E
Failed to get adapter index.
4      13:35:07.123 09/11/12 Sev=Warning/2
CVPND/0xA3400015
Error with call to IpHlpApi.DLL: CheckUpVASettings: Found IPADDR entry addr=10.98.70.169, error 0
5      13:35:08.123 09/11/12 Sev=Warning/2
CVPND/0xA3400015
Error with call to IpHlpApi.DLL: CheckUpVASettings: Found IPADDR entry addr=10.98.70.169, error 0
6      13:35:09.123 09/11/12 Sev=Warning/2
CVPND/0xA3400015
Error with call to IpHlpApi.DLL: CheckUpVASettings: Found IPADDR entry addr=10.98.70.169, error 0
7      13:35:10.123 09/11/12 Sev=Warning/2
CVPND/0xA3400015
Error with call to IpHlpApi.DLL: CleanUpVASettings: Was able to delete all VA settings after all, error 0
8      13:35:11.861 09/11/12 Sev=Warning/2
IKE/0xA3000067
Received an IPC message during invalid state (IKE_MAIN:512)
9      13:35:12.407 09/11/12 Sev=Warning/2
IKE/0xA3000067
Received an IPC message during invalid state (IKE_MAIN:512)

Help with writing and retrieving data from a table field with type "LCHR"

Hi Experts,
I need help with writing and reading data from a database table field which has a type of "LCHR". I have given an example of the original code but don't know what to change it to in order to fix it and still read in the original data that's stored in the LCHR field.
Basically we have two Function modules, one that saves list data to a database table and one that reads in this data. Both Function modules have an identicle table which has an array of fields from type INT4, CHAR, and type P. The INT4 field is the first one.
Incidentally this worked in the 4.7 non-unicode system but is now dumping in the new ECC6 Unicode system.
Thanks in advance,
C
SAVING THE LIST DATA TO DB
DATA: L_WA(800).
LOOP AT T_TAB into L_WA.
ZDBTAB-DATALEN = STRLEN( L_WA ).
MOVE: L_WA to ZDBTAB-RAWDATA.
ZDBTAB-LINENUM = SY-TABIX.
INSERT ZDBTAB.
READING THE DATA FROM DB
DATA: BEGIN OF T_DATA,
             SEQNR type ZDBTAB-LINENUM,
             DATA type ZDBTAB-RAWDATA,
           END OF T_TAB.
Select the data.
SELECT linenum rawdata from ZDBTAB into table T_DATA
     WHERE repid = w_repname
     AND rundate = w_rundate
     ORDER BY linenum.
Populate calling Internal Table.
LOOP AT T-DATA.
APPEND T_DATA to T_TAB.
ENDLOOP.

Hi Anuj,
The unicode flag is active.
When I run our report and then to try and save the list data a dump is happening at the following point
LOOP AT T_TAB into L_WA.
As I say, T_TAB consists of different fields and field types whereas L_WA is CHAR 800. The dump mentions UC_OBJECTS_NOT_CONVERTIBLE
When I try to load a saved list the dump is happening at the following point
APPEND T_DATA-RAWDATA to T_TAB.
T_DATA-RAWDATA is type LCHR and T_TAB consists of different fields and field types.
In both examples the dumps mention UC_OBJECTS_NOT_CONVERTIBLE
Regards
C

After recent upgrade to Yosemite on Macbook air bluetooth audio cuts out and associated video stops with audio. Likewise with airplay and Apple TV. I have deleted all my saved wifi connections and restarted numerous times. I do not expect a resolutio

After recent upgrade to Yosemite on Macbook air bluetooth audio cuts out and associated video stops with audio. Likewise with airplay and Apple TV. I have deleted all my saved wifi connections and restarted numerous times. I do not expect a resolution from the community, but hope to get the attention of Apple engineers. If you are having same problems or have a miracle cure I am all ears.

May start my own thread, but I'm having similar issues.
I've been using an old iMac (running 10.7.5) and Apple TV for years with no issues. Last week I bought a new Macbook Pro running Yosemite and have had audio issues multiple times. The weird thing is that sometimes it works flawlessly, other times (like now) I spend half an hour just trying to get a song to play.
My issues are: When I got to "computers" in Apple TV to stream my music, my music is sometimes chopper or intermittent, and I seen to know when it's going to happen based on the status wheel just before it plays. When I choose a song, the status wheel will spin for an unusually long time, usually an indicator that the audio is either not going to work, or stutter.
When it does finally pull up a song, the playhead sits at the beginning of the song for a good 3-5 seconds before actually playing. Then, when it starts playing, it's all downhill. It will play a few seconds, drop out, play a few more seconds, drop out, and then ultimately the playhead will keep moving across the song as if it's playing, but there's no audio.
Again, this is a new phenomenon never experienced by me. I've tried everything I could think of, some of them all at once:
• restart Apple TV
• restart Macbook Pro
• quite iTunes/open
• turn off Home Sharing on iTunes then reconnect it
• unplugging and cycling both my modem and router
None of these have alleviated the problem.
The odd thing is, like this morning, the audio started up perfectly and never gave me any issues. It wasn't until later in the day that it started. Perhaps after the macbook pro had been put to sleep? Not sure.
Regardless, this is an annoying trait, one that's new to me and my system (as stated, worked flawlessly until my new purchase), and is 100% limited to either a) the macbook pro b) Yosemite or c) both of them.

Help with count and sum query

Hi I am using oracle 10g. Trying to aggregate duplicate count records. I have so far:
SELECT 'ST' LEDGER,
CASE
WHEN c.Category = 'E' THEN 'Headcount Exempt'
ELSE 'Headcount Non-Exempt'
END
ACCOUNTS,
CASE WHEN a.COMPANY = 'ZEE' THEN 'OH' ELSE 'NA' END MARKET,
'MARCH_12' AS PERIOD,
COUNT (a.empl_id) head_count
FROM essbase.employee_pubinfo a
LEFT OUTER JOIN MMS_DIST_COPY b
ON a.cost_ctr = TRIM (b.bu)
INNER JOIN MMS_GL_PAY_GROUPS c
ON a.pay_group = c.group_code
WHERE a.employee_status IN ('A', 'L', 'P', 'S')
AND FISCAL_YEAR = '2012'
AND FISCAL_MONTH = 'MARCH'
GROUP BY a.company,
b.district,
a.cost_ctr,
c.category,
a.fiscal_month,
a.fiscal_year;
which gives me same rows with different head_counts. I am trying to combine the same rows as a total (one record). Do I use a subquery?

Hi,
Whenever you have a problem, please post a little sample data (CREATE TABLE and INSERT statements, relevant columns only) from all tables involved.
Also post the results you want from that data, and an explanation of how you get those results from that data, with specific examples.
user610131 wrote:
... which gives me same rows with different head_counts.If they have different head_counts, then the rows are not the same.
I am trying to combine the same rows as a total (one record). Do I use a subquery?Maybe. It's more likely that you need a different GROUP BY clause, since the GROUP BY clause determines how many rows of output there will be. I'll be able to say more after you post the sample data, results, and explanation.
You may want both a sub-query and a different GROUP BY clause. For example:
WITH    got_group_by_columns     AS
     SELECT a.empl_id
     ,     CASE
                    WHEN c.category = 'E'
              THEN 'Headcount Exempt'
                    ELSE 'Headcount Non-Exempt'
            END          AS accounts
     ,      CASE
                    WHEN a.company = 'ZEE'
                    THEN 'OH'
                    ELSE 'NA'
            END          AS market
     FROM              essbase.employee_pubinfo a
     LEFT OUTER JOIN mms_dist_copy             b ON   a.cost_ctr     = TRIM (b.bu)
     INNER JOIN       mms_gl_pay_groups        c ON   a.pay_group      = c.group_code
     WHERE     a.employee_status     IN ('A', 'L', 'P', 'S')
     AND        fiscal_year           = '2012'
     AND        fiscal_month          = 'MARCH'
SELECT    'ST'               AS ledger
,       accounts
,       market
,       'MARCH_12'          AS period
,       COUNT (empl_id)      AS head_count
FROM       got_group_by_columns
GROUP BY accounts
,            market
;But that's just a wild guess.
You said you wanted "Help with count and sum". I see the COUNT, but what do you want with SUM? No doubt this will be clearer after you post the sample data and results.
Edited by: Frank Kulash on Apr 4, 2012 5:31 PM

MOVED: [Athlon64] Need Help with X64 and Promise 20378

This topic has been moved to Operating Systems.
[Athlon64] Need Help with X64 and Promise 20378

I'm moving this the the Administration Forum. It seems more apporpiate there.

Airplay and Pioneer Reciever Connectivity

Just bought a Pioneer reciever (VSX-2) with Airplay. I have exhausted myself trying to get the two to talk. My Pioneer needs to connect to Airport Xtreme base station. Pioneer requires DCHP, DNS, IP etc on a manual basis versus automatically recognizing like Apple TV, etc. Pioneer wisely incorporated Airplay into it's new recievers (VSX 50, 51 52, 53, etc) but made it difficult for the Apple network to recognize. I feel like they want to make you buy there adaptor which connects to the back of the receiver but that costs $149.
My quick fix is to spend $99 on Apple TV and not go throught the pain with Pioneer, then again, there must be a way to make the Airport Extreme and Pioneer VSX52 talk and I'm just one step away from seeing that happen.
Airport Express: I can use one but don't think I need one as a bridge between Pioneer reciever and Airport Extreme.
This is all recently new so the knowledge base in combining is also new with regard to recievers (Pioneer/Phillips).
Help please....

Not sure why your Pioneer receiver is unable to perform as a DHCP client, but adding the appropriate IP address information should be relatively straight-forward.
You can easily get the information using your iMac and going to: System Preferences > Network > Ethernet or AirPort depending on how your iMac connects to the network.
Here's an example from mine. Note: I'm using OS X Lion so it will look a bit different from yours.
For the Pioneer, the DHCP address = Router address; DNS = DNS Server, etc. However, DON'T use your iMac IP address for the IP address used by the Pioneer. The IP address you should use would be in the same subnet, BUT OUTSIDE of the DHCP server range of your router. By default, the AEBS, uses 10.0.1.2 thru 10.0.1.200 for these addresses. I would suggest using 10.0.1.210 for the Pioneer.

Please help with TV and home theater system for very large basement room....

I'm looking to get my boyfriend either a TV or home theater system for the basement. I know he eventually wants a 3d TV. Right now he has a set up where he has 2 tv's so he can play video games and watch sports.
The basement that the tv and home theater system will be in is large (I'd estimate at least 15 ft x 30 ft...maybe more) so I want to make sure the home theater system will be enough for the room. We live in a ranch so basically the basement is almost the size of the house with some of it being storage.
I've started to look at products online but there are so many and technology isn't really my thing.
If anyone could help with recommendations for the home theater system and/or the tv I'd appreciate it!
Thanks so so sooo much!!!!

What will he be using the HT system for? Just watching sports or skipping the movie theater and watching them at home. If you plan to watch them at home your going to be on a tight budget with the home theater system but it is possible. Spend good money on the sub, that is one speaker you don't want to skimp out on. With such a big space you have a lot of room to fill and the cheap subs aren't going to cut it. You will probably need two subs as it is. The speakers I recommend on a tight budget Polk or Klipsch. My list includes a Denon receiver as I am a Denon fan but Yamaha, Onkyo, or Pioneer will suffice.
Here is a Option 1 will run you about 1700 with just one sub. You could always go up a model on each speaker if you feel the one sub is enough. I like an explosion sounding like it happened in front of me so that is why I mention 2 subs.
http://www.bestbuy.com/site/Denon+-+630W+7.1-Ch.+3D+Pass+Through+A/V+Home+Theater+Receiver/9894577.p...
http://www.bestbuy.com/site/Polk+Audio+-+Dual+5-1/4%22+2-Way+Floor+Speakers+(Each)+-+Black/8825453.p... speakers&cp=1&lp=12
http://www.bestbuy.com/site/Polk+Audio+-+5-1/4%22+Bookshelf+Speakers+(Pair)+-+Black/8825444.p?id=120... speakers&cp=1&lp=2
http://www.bestbuy.com/site/Polk+Audio+-+5-1/4%22+Center-Channel+Speaker+-+Black/8826149.p?id=120735... speakers&cp=1&lp=28
http://www.bestbuy.com/site/Speakers/Subwoofer-Speakers/abcat0205008.c?id=abcat0205008&&initialize=f...
Option 2 will cost $1400 before a subwoofer
http://www.bestbuy.com/site/Denon+-+630W+7.1-Ch.+3D+Pass+Through+A/V+Home+Theater+Receiver/9894577.p...
http://www.bestbuy.com/site/Mirage+-+OS%26%23179%3B-CC+Ompipolar+3-Way+Center-Channel+Speaker+-+Blac... speaker&cp=1&lp=11
and 4 of the below speaker
http://www.bestbuy.com/site/Mirage+-+OS%26%23179%3B-SAT+4-1/2%22+2-Way+Satellite+Speaker+(Each)+-+Hi... speaker&cp=1&lp=15

IPad 2, AirPlay, and Pioneer VSX-60 connectivity

I purchased the Pioneer VSX_60 receiver a few months ago. Part of the selling point was the AirPort connectivity. I was able to get my iPhone 4 to connect to the receiver as well as my iPad 2 for about a month. Had a slight problem with the receiver and reset the software back to factory settings. I have not been able to connect since that time. I have the current version of software on ALL products (Apple and Pioneer). My Apple devices all "see" the VSX-60 as it appears as an option when selecting AirPlay output. When I select the receiver, music stops, if i hit play, it will default back to the current device either iPad or iPhone. I've tried checking all my settings through my AirPort Extreme base as well as my AirPort Express. AirPlay works fine through my Apple TV. Any ideas or recommendations would be greatly appreciated. Thanks in advance!

Not sure why your Pioneer receiver is unable to perform as a DHCP client, but adding the appropriate IP address information should be relatively straight-forward.
You can easily get the information using your iMac and going to: System Preferences > Network > Ethernet or AirPort depending on how your iMac connects to the network.
Here's an example from mine. Note: I'm using OS X Lion so it will look a bit different from yours.
For the Pioneer, the DHCP address = Router address; DNS = DNS Server, etc. However, DON'T use your iMac IP address for the IP address used by the Pioneer. The IP address you should use would be in the same subnet, BUT OUTSIDE of the DHCP server range of your router. By default, the AEBS, uses 10.0.1.2 thru 10.0.1.200 for these addresses. I would suggest using 10.0.1.210 for the Pioneer.

HT1600 NEED HELP WITH AIRPLAY!!!!

I have a later 2011 macbook pro and I cant get airplay mirroring to work please help!

AirPlay Mirroring is compatible with your Mac, but it requires OS X Mountain Lion > http://support.apple.com/kb/HT5404 You have two possibilities:
1. Make a Time Machine backup and/or a clone with Carbon Copy Cloner, open App Store and purchase Mountain Lion. After upgrading, you will be able to turn on AirPlay Mirroring on the AirPlay icon on the at the top right or on System Preferences > Displays.
2. Install AirParrot > http://www.airparrot.com
I recommend the first option, as you will get the most recent version

Trouble with AirPlay and streaming from iTunes when on same wireless band

I was having this problem with AirPlay before, but after the last update now I'm having the same problem with iTunes streaming. (Apple TV 2nd gen)
The problem is this: if I try to stream something via AirPlay or my iTunes library and both devices are on the same wireless band (I have a dual-band cisco E2500 router), for example, the 5ghz band, then streaming will be extremely slow and choppy to the point of losing connection. If however, one of the devices is on a different band (my MacBook on the 2.4ghz and the AppleTV on the 5ghz, for example), then everything works fine.
I've already upgraded my router's firmware, so that didn't help.
Has anyone else run into this and been able to resolve the issue?

Hi jack4120,
Thanks for using Apple Support Communities. This article has a list of things to check for issues using AirPlay:
iTunes: Troubleshooting AirPlay and AirPlay Mirroring
http://support.apple.com/kb/TS5209
Troubleshooting performance issues
Wi-Fi Connection
If you are experiencing intermittent playback or significant network lag with AirPlay, it could be due to a weak Wi-Fi connection, interference, or the distance between the Wi-Fi router and your AirPlay-enabled device.
Ensure that other devices aren't trying to stream to the same Apple TV at the same time.
Ensure that your Wi-Fi router is set up with the recommended settings for the best performance.
Certain external devices, such as microwave ovens and baby monitors, may interfere with a Wi-Fi network. Try moving or disabling these devices.
If your wireless and wired networks are the same, try connecting your Apple TV to the router via Ethernet instead of Wi-Fi.
Use the Wi-Fi network troubleshooting guide to resolve interference and other issues.
Cheers,
- Ari

What can I do with airplay and 1st gen iPad?

I just set up my new 2nd gen atv. I have a 1st gen iPad. Besides using it for movies, photos. what else can I do with Airplay. I've seen posts about using it for games such as racing but I looked at a couple of racing games I have and don't see how to send it to my tv like a movie. Any help is much appreciated!

Websites and third party Apps need enabling before they will allow AirPlay of Video content. Some Website/App developers have not enabled their products, some simply haven't got around to it yet, others have stated that they won't be enabling AirPlay (likely as a result of licensing issues).
I have created a User Tip to list Apps that have been tested with Video Airplay, if you have any Apps that you have tested please leave details in the comments at the bottom of the User Tip or email me if you don't have commenting privileges.

Suddenly I do not could reach my Time Capsule...??? I can surf on net, but I could not stream music with Airplay and my Time Machine could not either take back up!? What is wrong?

Why could I suddenly do not play music to my music components with Airplay, as I could do yesterday? And my Time Machine could not take back up because my MacBook Pro could not find my Time Capsule? My internet connect is OK...! What´s wrong today?

Power down everything in the network.. start up in the correct order..
Modem.
TC
Any other network devices.
Computers and clients.
Everything needs a couple of minutes to get running before you start up the next part.
If it doesn't fix it.. we need a whole lot more info.
What Modem? Is it a router?
How is the TC setup? How is it connected to the modem?
What are you using for airplay?
We need full details on every part of the network.. otherwise we have no way to help.

Help with Mathscipt and for loop

I have a code in Mathscript/matlab and I need to output the array out. One option is my first code,the other option is using a for loop, but I am only getting the last ouput out. I need to get the whole output out.
Any help.
Thanks
Solved!
Go to Solution.
Attachments:
Help with Mathscript_for loop.vi ‏115 KB
Help with Mathscript_for loop2.vi ‏84 KB

Here's how it should look like.
Message Edited by altenbach on 10-30-2008 05:12 PM
LabVIEW Champion . Do more with less code and in less time .
Attachments:
MathscriptInFOR.png ‏15 KB

Need help with JTextArea and Scrolling

import java.awt.*;
import java.awt.event.*;
import java.text.DecimalFormat;
import javax.swing.*;
public class MORT_RETRY extends JFrame implements ActionListener
private JPanel keypad;
private JPanel buttons;
private JTextField lcdLoanAmt;
private JTextField lcdInterestRate;
private JTextField lcdTerm;
private JTextField lcdMonthlyPmt;
private JTextArea displayArea;
private JButton CalculateBtn;
private JButton ClrBtn;
private JButton CloseBtn;
private JButton Amortize;
private JScrollPane scroll;
private DecimalFormat calcPattern = new DecimalFormat("$###,###.00");
private String[] rateTerm = {"", "7years @ 5.35%", "15years @ 5.5%", "30years @ 5.75%"};
private JComboBox rateTermList;
double interest[] = {5.35, 5.5, 5.75};
int term[] = {7, 15, 30};
double balance, interestAmt, monthlyInterest, monthlyPayment, monPmtInt, monPmtPrin;
int termInMonths, month, termLoop, monthLoop;
public MORT_RETRY()
Container pane = getContentPane();
lcdLoanAmt = new JTextField();
lcdMonthlyPmt = new JTextField();
displayArea = new JTextArea();//DEFINE COMBOBOX AND SCROLL
rateTermList = new JComboBox(rateTerm);
scroll = new JScrollPane(displayArea);
scroll.setSize(600,170);
scroll.setLocation(150,270);//DEFINE BUTTONS
CalculateBtn = new JButton("Calculate");
ClrBtn = new JButton("Clear Fields");
CloseBtn = new JButton("Close");
Amortize = new JButton("Amortize");//DEFINE PANEL(S)
keypad = new JPanel();
buttons = new JPanel();//DEFINE KEYPAD PANEL LAYOUT
keypad.setLayout(new GridLayout( 4, 2, 5, 5));//SET CONTROLS ON KEYPAD PANEL
keypad.add(new JLabel("Loan Amount$ : "));
keypad.add(lcdLoanAmt);
keypad.add(new JLabel("Term of loan and Interest Rate: "));
keypad.add(rateTermList);
keypad.add(new JLabel("Monthly Payment : "));
keypad.add(lcdMonthlyPmt);
lcdMonthlyPmt.setEditable(false);
keypad.add(new JLabel("Amortize Table:"));
keypad.add(displayArea);
displayArea.setEditable(false);//DEFINE BUTTONS PANEL LAYOUT
buttons.setLayout(new GridLayout( 1, 3, 5, 5));//SET CONTROLS ON BUTTONS PANEL
buttons.add(CalculateBtn);
buttons.add(Amortize);
buttons.add(ClrBtn);
buttons.add(CloseBtn);//ADD ACTION LISTENER
CalculateBtn.addActionListener(this);
ClrBtn.addActionListener(this);
CloseBtn.addActionListener(this);
Amortize.addActionListener(this);
rateTermList.addActionListener(this);//ADD PANELS
pane.add(keypad, BorderLayout.NORTH);
pane.add(buttons, BorderLayout.SOUTH);
pane.add(scroll, BorderLayout.CENTER);
addWindowListener( new WindowAdapter()
public void windowClosing(WindowEvent e)
System.exit(0);
public void actionPerformed(ActionEvent e)
String arg = lcdLoanAmt.getText();
int combined = Integer.parseInt(arg);
if (e.getSource() == CalculateBtn)
try
JOptionPane.showMessageDialog(null, "Got try here", "Error", JOptionPane.ERROR_MESSAGE);
catch(NumberFormatException ev)
JOptionPane.showMessageDialog(null, "Got here", "Error", JOptionPane.ERROR_MESSAGE);
if ((e.getSource() == CalculateBtn) && (arg != null))
try{
if ((e.getSource() == CalculateBtn) && (rateTermList.getSelectedIndex() == 1))
monthlyInterest = interest[0] / (12 * 100);
termInMonths = term[0] * 12;
monthlyPayment = combined * (monthlyInterest / (1 - (Math.pow (1 + monthlyInterest, -termInMonths))));
lcdMonthlyPmt.setText(calcPattern.format(monthlyPayment));
if ((e.getSource() == CalculateBtn) && (rateTermList.getSelectedIndex() == 2))
monthlyInterest = interest[1] / (12 * 100);
termInMonths = term[1] * 12;
monthlyPayment = combined * (monthlyInterest / (1 - (Math.pow (1 + monthlyInterest, -termInMonths))));
lcdMonthlyPmt.setText(calcPattern.format(monthlyPayment));
if ((e.getSource() == CalculateBtn) && (rateTermList.getSelectedIndex() == 3))
monthlyInterest = interest[2] / (12 * 100);
termInMonths = term[2] * 12;
monthlyPayment = combined * (monthlyInterest / (1 - (Math.pow (1 + monthlyInterest, -termInMonths))));
lcdMonthlyPmt.setText(calcPattern.format(monthlyPayment));
catch(NumberFormatException ev)
JOptionPane.showMessageDialog(null, "Invalid Entry!\nPlease Try Again", "Error", JOptionPane.ERROR_MESSAGE);
} //IF STATEMENTS FOR AMORTIZATION
if ((e.getSource() == Amortize) && (rateTermList.getSelectedIndex() == 1))
loopy(7, 5.35);
if ((e.getSource() == Amortize) && (rateTermList.getSelectedIndex() == 2))
loopy(15, 5.5);
if ((e.getSource() == Amortize) && (rateTermList.getSelectedIndex() == 3))
loopy(30, 5.75);
if (e.getSource() == ClrBtn)
rateTermList.setSelectedIndex(0);
lcdLoanAmt.setText(null);
lcdMonthlyPmt.setText(null);
displayArea.setText(null);
if (e.getSource() == CloseBtn)
System.exit(0);
private void loopy(int lTerm,double lInterest)
double total, monthly, monthlyrate, monthint, monthprin, balance, lastint, paid;
int amount, months, termloop, monthloop;
String lcd2 = lcdLoanAmt.getText();
amount = Integer.parseInt(lcd2);
termloop = 1;
paid = 0.00;
monthlyrate = lInterest / (12 * 100);
months = lTerm * 12;
monthly = amount *(monthlyrate/(1-Math.pow(1+monthlyrate,-months)));
total = months * monthly;
balance = amount;
while (termloop <= lTerm)
displayArea.setCaretPosition(0);
displayArea.append("\n");
displayArea.append("Year " + termloop + " of " + lTerm + ": payments\n");
displayArea.append("\n");
displayArea.append("Month\tMonthly\tPrinciple\tInterest\tBalance\n");
monthloop = 1;
while (monthloop <= 12)
monthint = balance * monthlyrate;
monthprin = monthly - monthint;
balance -= monthprin;
paid += monthly;
displayArea.setCaretPosition(0);
displayArea.append(monthloop + "\t" + calcPattern.format(monthly) + "\t" + calcPattern.format(monthprin) + "\t");
displayArea.append(calcPattern.format(monthint) + "\t" + calcPattern.format(balance) + "\n");
monthloop ++;
termloop ++;
public static void main(String args[])
MORT_RETRY f = new MORT_RETRY();
f.setTitle("MORTGAGE PAYMENT CALCULATOR");
f.setBounds(600, 600, 500, 500);
f.setLocationRelativeTo(null);
f.setVisible(true);
}need help with displaying the textarea correctly and the scroll bar please.
Message was edited by:
new2this2020

What's the problem you're having ???
PS.

HT4437 Help with airplay and pioneer AV amp

Similar Messages

Maybe you are looking for