HT4623 after updating my iphone4 it couldn't install the update becose the cable disconnected ,after reconection it still can't insall the software what ca i do
after update of software,my usb cable got disconected so the bsoftware coudn't install,how can i proceed to install the software back to my iphone.
Try going to settings, reset , reset network settings.
Similar Messages
-
Software update says I need to download MacOS 10.6.7. Each time I try, I have tried 6 times, the software downloads, it has me restart the system, it then writes the files to disk and then I get an error measage that "there was error in installing the softare. Anybody have this problem and how do you fix it? I am running 10.6.6
Try this before trying to install the update.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If you still have a problem then I suggest you download the 10.6.7 Combo Updater and install it. -
I updated my 2nd gen apple tv and after completing the downloading and installing the software I got an itunes picture that means i have to connect it to iTunes,, can i skip this ? coz i don't have the mini usb cable
No, if you have that picture it means the update went wrong and you need to restore via iTunes.
AC -
I updated my 2nd gen apple tv and after completing the downloading and installing the software I got an itunes picture that means i have to connect it to iTunes,, can i skip this ? because i don't have the mini usb cable
No, if you have that picture it means the update went wrong and you need to restore via iTunes.
AC -
i have dropped my iphone4 . i cant get to the software update the error has occured wt can i do for software update
What is the exact wording of the error message received?
-
i used my wifi to download ios 8 after like 5 hours it finished and then it let me install, while installing the software it shutdown and everytime i try to open it it shows up the itunes and the usp cable logo... when i plug in the usp cable it says in itunes( ipad recovery mode) and when i press restore it start downloading the ios software again...... wats tht and what i can do pls help. thnx
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary. -
I have an iPhone 4s and I attempted to update my device's iOS to 7.0.2. The download was successful but when I tried to install the software, it asked me to connect my device to iTunes. I did but my phone failed to load: ERROR 4013. What to do?
Hi there KrisonCastillo,
I would recommend taking a look at the troubleshooting steps found in the article below.
iOS: Unable to update or restore
http://support.apple.com/kb/HT1808
-Griff W. -
I Just downloaded the latest software for Yosemite 10.10 after it restarted and installed the software it stopped, now I have a white screen. What should I do now?
Hi ..
Hold down the power button until the screen goes black.
Wait about ten seconds then restart your Mac while holding down the Command + R keys.
From there you should be able to access the built in utilities to verify and repair the startup disk if necessary and reinstall OS X. (10.10.1) -
HT4623 How do I instal the software updates? My iphone does not show the software update
How to do I instal the software updates to my iphone?
Same as always.
Tun on your computer.
Open itunes
Connect iphone.
That's it. It will prompt you to update if one is available -
Can't install the software because it is not currently available from the Software Update server. this is the message that i get a few days now that i am trying to install windows through boot camp to my macbook!does anybody knows what i can do????
You keep it on the usb stick for after you boot into Windows. From Windows you install the Windows Support software on the stick. Do you realize that you need to buy and install Windows? The Windows Support software you downloaded is only the Windows drivers for your hardware.
Read the Boot Camp installation instructions and help guides located here: http://www.apple.com/support/bootcamp/ -
Can't install the software for the EPSON Epson Stylus Photo R2000 because it is not currently available from the Software Update server???
I am using mac osx 10.8 and now cant get print software for epson R2000 printer.After system update, my Epson Stylus SX 535WD was ''gone''. I tried in vain to add it as an IP printer (got the IP-address from the printer). The printer model is correctly recognized, software download starts -- but then the "software ... is not currently available..."
Resetting the printing system did not help. Downloading Epson Printer Drivers v2.15.1 from here
did not help either, downloading Epson Printer Drivers.
In the end, I re-installed the printer software from the original CDs. After that the printer showed up as a Bonjour Printer, and I could add it without problem.
But note: although the printer is installed now and working properly, I still get the old error message (...software ..not available...) if I try to add the printer as an IP printer !? -
I am trying to install the software drivers for Windows 7 Home using Boot Camp 4 Assistant. I receive the following message: "Can't install software because it is not currently available from the Software Update server." Why is this happening?
You keep it on the usb stick for after you boot into Windows. From Windows you install the Windows Support software on the stick. Do you realize that you need to buy and install Windows? The Windows Support software you downloaded is only the Windows drivers for your hardware.
Read the Boot Camp installation instructions and help guides located here: http://www.apple.com/support/bootcamp/ -
Error: Boot camp assistant: Can't install the software because it is not currently available from the Software Update server.
OS 10.9.1
iMac 27-inch, Late 2009
Boot Camp Assistant Version 5.1.0 (473)
Every time I run this I get the above error after I hit "Continue" on the "Save Windows Support Software" page and subsequently hit "Download Windows 7 Support Software."
How do I successfully install 64 bit WIndows 7 on my iMac?
Thank you!Waited a month and tried again with the same result. What gives? Does Apple no longer support Bootcamp with Windows 7? Do they not read these posts and help out customers? If Apple doesn't care and won't help, can anyone else suggest something? My large company does not like Apple and barely supports those of us who buck the trend and buy Macs. If I have to buy a PC to support their software to work from home this only gives them more "ammunition" to decline to support Macs. Any advice anyone can give would be greatly appreciated!
-
I'm trying to setup my Canon MX870 USB ink jet printer plugged into my Airport Extreme's USB port. However, I keep getting a message of; "Can't install the software for the Canon MX870 series because it is not currently available from the Software Update server." And then I have to click cancel.
The "Print & Scan" from System Preferences, can see the printer as it has the NAME: Canon MX870 series, and the LOCATION: 'the name of my network', and USE: MX870 series. But after clicking "Add", it tries to install the software (I've already installed the latest drivers however on my Mac Pro) and that's when I get this message;
"Can't install the software for the Canon MX870 series because it is not currently available from the Software Update server."
Any ideas, help would be greatly appreciated!
MartyHello Marty,
It sounds like you are not able to add your Canon printer in System Preferences. I found an article with steps you can take to resolve this:
Resolution
USB printers and Bonjour-enabled network printers
Follow these steps until the issue is addressed:
Make sure that the printer is powered on, has ink / toner, and that there are no alerts on the printer’s control panel. Note: If you cannot clear an alert on the printer's control panel, stop here and check the printer's documentation or contact the manufacturer for support.
Ensure the printer is properly connected to a USB port on the Mac or AirPort base station / Time Capsule. If the printer is a network-capable printer, make sure that it is properly connected to your home network.
Use Software Update to find and install the latest available updates. If an update is installed, see if the issue persists.
Open the Print & Scan pane or Print & Fax (Snow Leopard) pane in System Preferences.
Delete the affected printer, then add the printer again.
If the issue persists, try these additional steps:
Reset the printing system, then add the printer again.
If the issue still persists, reset the printing system again. Download and install your printer's drivers. Then, add the printer again.
Contact the printer vendor or visit their website for further assistance.
You can find the full article here:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Thank you for posting in the Apple Support Communities.
Best,
Sheila M. -
We have a canon printer and it connects fine to my boyfriend's HP. I can't get it to connect to my macbook though--when I plug it in with USB it asks me if I want to install the software, has me agree ot the user terms and conditions, and then I get the error message. I've installed all updates, tried turning my computer on and off. Where do I go from here?
Did you install the Software Update beforehand? I believe you need this so that your Mac's database will update on your newly connected devices. Try the solutions here. I just did what it says there and then restart my computer and my router after all the process and it works for me. Goodluck!
http://www.techyv.com/questions/software-not-available-software-update-server
Maybe you are looking for
-
I've made several books (8-10) using iphoto 5 with no problems. iphoto six has failed every time I've tried it with 2 books printed with no cover or inside typing and two books rejected (unprintable) at the web site. The failure is evident when previ
-
I have been having trouble with Illustrator quiting unexpectedly. Apple gathers the info and tries to send the problem but for some reason I get a message that it couldn't submit the report and it has failed and to try again. I have checked my securi
-
Not using substitute material while creating sales order with function?
hi experts. I use SD_SALESDOCUMENT_CREATE function to create a sales order. Material A has a substitute material B with substitute reason 0005. So if I use material A when creating sales order with SD_SALESDOCUMENT_CREATE, the order is created with m
-
An error occured during the installation of assembly component
Hello, there is an error durring the installation of Adobe Reader X: >> An error occured during the installation of assembly component {B708EB72-AA82-3EB7-8BB0-D845BA35C93D}. HRESULT: 0x80070BC9. << To give you some backround informations: It is a Wi
-
Error when invoking webservice from ODI
Hi all, When I execute my ODI scenario ( This scenario call a BPEL websevrice ) ,I Have this error , please have you any idea, com.sunopsis.wsinvocation.SnpsWSInvocationException: Error doing JNDI lookup on target jdbc/PRT_DBDS at com.sunopsis.w