HT4972 can't connect to network with linksys e2500

Can't connect to network with linksys E2500. Can anyone help me?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Similar Messages

[solved] Can't connect to network with 64-bit kernel

On 64-bit Arch Linux, I can't get any network access. On 32-bit Arch Linux, I can connect to my router with an ethernet cable or a wireless card using dhcpcd or networkmanager.
In 64-bit, I have tried
- Upgrading my kernel from 3.3.8 to 3.4.2 from the testing repos
- Getting networkmanager-git from AUR
- Using the r8168 driver for my ethernet card (which is actually exactly the same one as the one from https://wiki.archlinux.org/index.php/Co … k_messages )
But I haven't been able to get "dhcpcd eth0" to tell me anything but
dhcpcd[677]: eth0: sending IPv6 Router Solicitation
dhcpcd[677]: eth0: broadcasting for a lease
dhcpcd[677]: eth0: sending IPv6 Router Solicitation
dhcpcd[677]: eth0: sending IPv6 Router Solicitation
dhcpcd[677]: eth0: sending IPv6 Router Solicitation
dhcpcd[677]: eth0: no IPv6 Routers available
while "dmesg | tail" fills with
eth0: no IPv6 routers present
eth0: no IPv6 routers present
eth0: no IPv6 routers present
My rc.conf has the correct settings for dhcp:
interface=eth0
address=
netmask=
broadcast=
gateway=
I can get whatever 64-bit packages I need to get the internet to work in 64-bit linux by downloading them in 32-bit linux and then upgrading to 64-bit linux.
My goal is to get networking to work on 64-bit linux through either eth0 or wlan0 (eventually I'll need wlan0 but right now neither works, so if one starts working, the other probably will), or for someone to say "It's impossible dude, go download opensuse and see if you get a different damning error over there".
Happy trails,
jc
Last edited by jc (2012-06-13 23:21:31)

ewaller wrote:Are you doing this on the same computer with different kernels?
Yep.
Are you sharing /etc between the 32 and 64 bit kernels?
Yes. Networking doesn't work on the 64-bit install disk either though, which obviously doesn't share its /etc with anything.
Can you post your 64 bit system's /etc/dhcpcd.conf file?
hostname
option domain_name_servers, domain_name, domain_search, host_name
option classless_static_routes
option ntp_servers
option interface_mtu
require dhcp_server_identifier
nohook lookup-hostname
noipv4ll
On your 64 bit system, what is the output of ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 14:da:e9:0f:69:85 brd ff:ff:ff:ff:ff:ff
inet6 fe80::16da:e9ff:fe0f:6985/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether e0:69:95:d3:7e:e9 brd ff:ff:ff:ff:ff:ff
What is the version of your 32 bit kernel?
3.3.8
Have you tried dhclient instead of dhcpcd ?
I have. No cake.

Can't connect to network with mac, only pc.

I have a powerbook and have just installed an airport extreme card. I do not have my own internet connection and intend to 'borrow' connections that I pick up.
In the past I have used a friend's PC laptop &belkin wireless adapter to connect to networks accidentally found in both his house and mine. This was no problem whatsoever and a connection without passwords etc was possible in both.
When I try to connect my powerbook the following happens:
1. In his house: I can connect to an open apple network but the connection is unbearably slow while I can work on his computer from the same point relatively easily.
2. In my house: When I try to connect I get 'error in connection to linksys' or similar (maybe even get asked for passwords).
I have very limited knowledge of these things and have no idea what it means or what the problem is.
If anyone can tell me why the connection always seems to be slow or unachievable on my powerbook (when an old PC laptop succeeds) I'd be most grateful.

It could be as simple as the owners of those wireless networks didn''t want other people using their networks and have added a layer of security.
One you may also want to have a look at these recent cases involving using other people's wireless networks.
UK Case
http://news.bbc.co.uk/1/hi/technology/4721723.stm
US Case
http://money.cnn.com/2005/07/07/technology/personaltech/wireless_arrest/

Can't connect to network with Airport Extreme

I have just purchased and installed an Airport Extreme card (firmware version 405.1) into my eMac (with ATI graphics). The card appears in System Profiler, and I have attached the antenna wire. However, it cannot see my network (the only network in range). My iPhone can see the network when it is in the same location (as can a few Windows devices).
I have tried turning off encyption, to no avail. I believe my router is broadcasting on a frequency my card can recieve.
I have also tried resetting my SystemConfiguration folder. What else should I try?

Thanks again for the suggestions.
I had tried the router on 1 and 6, just tried it on 11 as well. No joy.
It is broadcasting the SSID.
MAC filtering isn't on.
...and then I put it back to channel 1, and now it's working!
It's working now, and there doesn't seem to be any settings that are different to when I started.
The signal is increadibly low though. When I put the access point antenna literally in the drivebay, I get three bars (out of four). A meter away I get 2 or 1 and everything times out.
It appears that something is wrong with the antenna wire, or the connection to it. This was probably an important factor all along.

Can't connect Coby tablet with Linksys WRVS4400N Router

My new Coby tablet model #MIC1125-4G does not connect to my wireless network which is secured with a WEP key. The tablet connects everywhere else (Starbucks, etc.) and all my computers work in my wireless network. My router is a model #WRVS4400N. So it seems there is nothing wrong with my tablet and there is nothing wrong with my router. Do you know if there is an incompatibility issue?

Try updating the firmware for the router.
~Lyssa

I can't connect to network with my router

I am using the model WRT54G, and it is starting to refuse connections... Then i went to "Status -> Router" (in 192.168.1.1) and all camp fields are blank, with IP's 0.0.0.0. I upgraded my firmware and the problem stays at same...
Can anyone help me?
ThanksMessage Edited by The_Gladiator on 12-10-200610:39 AM

I had the same issue before I bought my new PC. I could not connect to the internet with my new PC wired to the router but could connected to the modem. I figured out the way to do it was clone the MAC address of the PC I used to setup the internet which was no longer wired. I disable Clone MAC and I would lose internet. Get nothing but 0.0.0.0 in the status page. I did a hard reset on the modem and disabled Clone MAC in the router. Powered everything off and waited about a minute. Powered everything back up and was in business. Had internet and didnt have to clone the MAC.
Now I dont know if this will work for you but it did for me.
If you have a modem with battery backup you need to unplug the power cord then remove the battery to truely powercycle it. (Words from Comcast)

Can't connect to network with wep enabled

I'm having problems connecting my mbp to my wireless network. It connects fine with no security enabled but when security is enabled I type in the wep key and I get a message saying there was an error conecting.
I have read loads of other posts and it seems a lot of people have managed to sort this problem by putting a '$' in front of the wep key when trying to connect. This is not working for me.
Is anyone in the same boat?
Does anyone know how to get around this?

See if any of this helps:
http://docs.info.apple.com/article.html?artnum=300153
http://docs.info.apple.com/article.html?artnum=304197
http://docs.info.apple.com/article.html?artnum=106424
http://docs.info.apple.com/article.html?artnum=106250
http://www.apple.com/support/airport/
Be sure you have the latest Airport software installed on your computer. Depending upon the particular router you are using you may need a firmware update for the router (if it's third-party or an older Apple Base Station that may need a firmware update.)

Can't connect to network with hardwired desktop

I have a network set up in my house with a wireless router. However, my desktop (MS Vista Enterprise) is and always has been hardwired to the router. Out of the blue the desktop no longer recognizes the network and cannot connect or get online. All other wireless devices work fine. I have tried rebooting the computer, rebooting the router, completing a system restore, none of which have helped. I do notice that in Device Manager that Microsoft ISATAP Adapter #3 is "not working properly because Windows cannot load the drivers required (Code 31)." When I troubleshoot the problem it tells me that Windows is looking for and cannot find a wireless adapter (of which I've never had one).
Any idea what may have gone wrong and/or what I need to do to correct it? I'm out of ideas.

Hello Lena,
Thank you for posting!
Based on my experience, Microsoft ISATAP with error code 31 is an ignorable issue. For more information, please refer to the following KB article:
(KB932520) On a Windows Vista-based computer, the Microsoft ISATAP adapter appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
http://support.microsoft.com/default.aspx?scid=kb;EN-US;932520
In such a case, I suspect this problem to be caused by network adapter missing or corrupt. Please firstly reinstall the driver for your wireless network adapter. Then try to reinstall Microsoft ISATAP using following steps:
In Device Manger, right-click the item of Microsoft ISATAP and select Uninstall.
Still in Device Manager, click Action and select Add legacy hardware.
Click Next, and select Install the hardware that I manually select from a list (Advanced), click Next.
Select Network Adapters and click Next.
Select Microsoft in left panel and Microsoft ISATAP Adapter in the right panel.
Click Next and finish the remaining wizard.
Hope it helps!
Regards,
Lionel Chen
Microsoft Online Community Support

Hi there! We just got an ipod touch 8G. We have wireless internet, but can't join the network with the ipod touch! Very frustrating and we have tried all of the troubleshooting suggestions on the support site. Help! The router is a linksys WRT120N.

Hi everyone! WE just got an ipod touch 8G. We do have wireless internet, but can't join the network with the ipod touch. Message comes up.."unable to join the network".....very frustrating! We have tried all trouble-shooting suggestions on the site, but nothing is working. Anyone out there got any ideas for us?? The router is a Linksys WRT120N.
Thanks for any help any one can give!!!

Does the iPod connect to other neworks?
Do other devices connect to the network?
What encryption are you using?
How you tried changing the type of encruption? Changing to no encryption?

HT5304 Hi Guys, I'm running snow leopard 10.6.3 recently had update which left me with a DMSL launch problem. Rei installed software and now can't connect to Internet with cable or wifi ! can see network and router,. Help

Hi Guys, I'm running snow leopard 10.6.3 recently had update which left me with a DMSL launch problem. Re installed software and now can't connect to Internet with cable or wifi ! can see network and router. Have tried many things and now pulling my hair out !

recently had update
Care to share which update?
Have tried many things
Care to share?
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios.

Can I extend a network with an AirPort Extreme Base Station Rather than with an Express?

Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?

pcbjr wrote:
Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?
Hiya.
You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

Can't connect to wifi with my iPad

can't connect to wifi with my iPad

iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Imessage wont connect using my apple id says can not connect check network conection and my network connection is fine what do i do

having trouble with imessage since i updated to the ios7 cant get it to connect to imessage when i use my apple id says can not connect check network connection and my network connection is fine does anyone know what to do to fix this

i have the same problem but i didnt update

TS1398 Can't connect to hotspot with my iPad, picks it up but unable to connect. Any sugestions?

Can't connect to hotspot with my iPad, picks it up but unable to connect. Any sugestions?

When Access Connections fails to connect it asks if I want to configure the network and there's a bunch of settings. Connection type: infrastructure or Adhoc, Wireless security type "use static WEP keys", "Use Wi-Fi protected Access - Pre Shared Key (WPA-PSK)" - I choose it and under Properties there's more options. Access point authentication, WPA-PSK or WPA2-PSK; I've tried it both ways. Data encryption: TKIP or AES, I've been using TKIP. Under Pre-Shared Key, there's the only box I see to enter a password, so I enter the password there.
Chances are pretty good that the problem is the network configuration of your PC and not the AirPort Extreme Base Station (AEBS). What configuration options you choose will depend on how you set up the AEBS's wireless network, but the following can be used as a guideline:
o Connection Type: Infrastructure
o Wireless Security Type:
AirPort Setting = PC Setting
o WEP = WEP
o WPA Personal = WPA-PSK w/TKIP
o WPA2 Personal = WPA-PSK w/AES

I can't connect to wifi with iPhone5. Does anyone knows why? and what to do?

I can't connect to wifi with iPhone5. Does anyone knows why? and what to do?
Thank you.

The Holy Mecha of Wifi
Turn router off then on Try turning your wireless router off then back on.
Change or turn off wireless security You may want to try toggling the settings on your wireless router, switching from WPA to WEP or vice versa, or, as a last resort, turning wireless security off altogether. For AirPort routers, this can be accomplished with the AirPort Admin Utility. For other routers, this can usually be accomplished by accessing the router’s configuration page — open a browser and enter the address 192.168.1.1.
Reset network settings on iPad. On your iPad, open Settings, then navigate to “General” in the left-hand pane. Scroll down and tap Reset, then select “Reset Network Settings.” This will delete any stored WiFi passwords and other information, but may result in a more stable connection.
Adjust brightness upward. Oddly, a number of users have found that they can resolve this issue by simply adjusting the iPad’s brightness level upward and off the lowest setting. To do this, tap Settings, then select “Brightness & Wallpaper” from the left-hand pane. Slide the brightness bar upward, then wait 1-2 minutes and check for an improvement in signal strength. Speculation holds that a power delivery issue associated with the screen brightness affects Wi-Fi.
Change thresholds in router settings. Access your routers configuration screen (for most routers, open a browser and enter the address 192.168.1.1), then change the fragmentation threshold and the CTS/RTS threshold as described here. Some users have found success with the settings Fragmentation= 2048, RTS = 512.
Change 802.11 spec on router. Try changing your router’s wireless spec mode from B, G and N to G only or vice versa. For AirPort routers, this can be accomplished with the AirPort Admin Utility. For other routers, this can usually be accomplished by accessing the router’s configuration page — open a browser and enter the address 192.168.1.1.
Switch routers. Although a far-from-ideal solution, some users have found success with switching to a different wireless router.
Turn off “Ask to Join Networks.” To do so, tap Settings on your iPad, then select “Wi-Fi” from the left-hand pane. Slide “Ask to Join Networks” to off. Speculation holds that leaving this option on causes the iPad to constantly seek networks, resulting in some type of interference with the network to which it is connected.
Forget network then rejoin. Tap Settings on your iPad, then select Wi-Fi from the left-hand pane. Choose the network with which you are experiencing difficulty, then select “Forget this network.” Go back to the previous screen and rejoin the network.
Turn off Bluetooth. Some users report that, perhaps due to interference issues, turning off Bluetooth can boost Wi-Fi signal strength. To do so, tap Settings then tap General in the left-hand pane. Tap Bluetooth in the right-hand pane, then slide to off.

HT4972 can't connect to network with linksys e2500

Similar Messages

Maybe you are looking for