HT4993 how do i unlock and reset phone

how do i unlock my phone

if you mean unlock it from Sprint, only they can provide that service.

Similar Messages

  • HT1212 How do I unlock and reset my 4s? . iPhone Disabled

    I recently purchased an iPhone online and it is loced and disabled. I attempted to connect to iTunes and add new device however this has not worked. How do I unlock this phone and reset it?

    Follow the instructions in this support document, like explained in the earlier part of the thread. Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support

  • I have forgot my Iphone passcode. Itunes will not let me restore it, i do not have icloude,or find my iphone,and the closest itunes store is 4 hours away how can i unlock, or reset my phone?

    I have forgot my Iphone passcode. Itunes will not let me restore it, i do not have icloude,or find my iphone,and the closest itunes store is 4 hours away how can i unlock, or reset my phone?

    Try this:
    Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
    Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
       1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
           other end of the cable connected to your computer's USB port.
       2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
           until the red slider appears, then slide the slider. Wait for the device to turn off.
                  * If you cannot turn off the device using the slider, press and hold the
                    Sleep/Wake and Home buttons at the same time. When the device turns off,
                    release the Sleep/Wake and Home buttons.
      3. While pressing and holding the Home button, reconnect the USB cable to the
           device. The device should turn on. Note: If you see the battery charge warning,
           let the device charge for at least ten minutes to ensure that the battery has some
           charge, and then start with step 2 again.
      4. Continue holding the Home button until you see the "Connect to iTunes" screen.
           When this screen appears you can release the Home button:
      5. If necessary, open iTunes. You should see the following "recovery mode" alert:
      6. Use iTunes to restore the device.
    If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
    Additional Information:
    If you have a problem getting into recovery mode then try: RecBoot: Easy Way to Put iPhone into Recovery Mode.
    Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

  • HT1688 How do i unlock my I-Phone 4? The phone turns on and turns off by itself!

    How do i unlock my I-Phone 4. The phone turns on and off by itself! I need to resiolve this problem asap!
    Thank you,
    Mark

    OK, first - typing in all caps is the equivalent of yelling at people.
    If your device is disabled, then you will need to follow the steps in the link below that best apply to your situation. If you  do not have a backup in iTunes or iCloud to restore from, then I'm afraid that you will lose whatever data you have on the device:
    iOS: Device Disabled
    Best of luck,
    GB

  • How to factory unlock my i phone 5

    How to factory unlock my i phone 5

    Ask your cellular provider to unlock the phone if they are able, and if they will unlock it.

  • HT1386 Just downloaded 7.2 into my Iphone 5 what a mess.  Dropped called no audible notifications for email or text messages.  Went to the apple store and reset phone to original specs. Now trying to restore apps and music and itunes will not recognize th

    Just downloaded 7.2 into my Iphone 5 what a mess.  Dropped called no audible notifications for email or text messages.  Went to the apple store and reset phone to original specs. Now trying to restore apps and music and itunes will not recognize the phone.  I have gone thur the steps for windows 7 and still nothing???  I have downloaded the newest version I itunes too. 

    Hi Midwestboy,
    If your iPhone isn't being recognized by iTunes on your Windows machine, you may find the following article helpful:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    Regards,
    - Brenden

  • I used to be a softbank Japan Iphone 4 customer and i had cleared all the dues. Now i don't have softbank contract and i am in my country Nepal. How can i unlock and use my Iphone here in Nepalese Network ?

    I used to be a softbank Japan Iphone 4 customer and i had cleared all the dues. Now i don't have softbank contract and i am in my country Nepal. How can i unlock and use my Iphone here in Nepalese Network ?

    Hi Edward,
    You should still be able to manually manage the music on your iPhone within iTunes. Make sure that when your iPhone is plugged in, look in the Summary tab to see if “Manually manage music and videos” is enabled and you can even you turn off Automatically Sync when this iPhone is connected. Take a look at the first article below to give more information on that. As far as your other questions about calling someone, I have provided two options for you. If it is for feedback on iTunes, you can use the second link to give detailed feedback on what is going on. If you want to actually talk to someone, the last link has a list of numbers for you to call for any support or service that you may need.  
    Manage content manually on your iPhone, iPad, and iPod
    http://support.apple.com/en-us/HT201593
    Product Feedback
    http://www.apple.com/feedback/
    Contact Apple for support and service
    http://support.apple.com/en-us/HT201232
    Take it easy,
    -Norm G. 

  • My iPod nano has a lock on the screen.How can I unlock and use my nano?

    My iPod nano has a lock on the screen. How can I unlock and use my iPod?

    Do you know there is the lock/unlock thing on the top or bottom right? If that doesn't work, hold down the middle circle and top portion of the circle button at the same time and hold until the screen goes black. Let go and soon an apple will appear. If you wait / press some buttons (i am not sure exactly how this part works) it will turn white and then the screen will appear again. You have all your music and everything still but the problem should be gone. This also works if your iPod ever freezes.

  • I am traveling out of state every time ,how can i unlocked my i phone 4 to using overseas

    i am traveling out of state every time,how can i unlocked my i phone 4 to use outside u.s ??

    All iPhones sold in the US are locked to either AT&T or Verizon with no offical way to unlock them.

  • My deceased brother's IPad was given to me but it is locked and passcode protected.  I do not want access to the data on it, but would like to be able to use it.  Can it be unlocked and reset to factory settings?  Thanks!

    My deceased brother's IPad was given to me but it is locked and passcode protected.  I do not want access to the data on it, but would like to be able to use it.  Can it be unlocked and reset to factory settings?  Thanks!

    You can try this: If you can't update or restore your iOS device
    If he had not turned on Find My iPad then it will work, if he had you will run into Activation Lock. If you do run into it you can take a copy of the will (or probate finding if he died without one) and/or a Letter Testamentary and ask if they can look up where he purchased it. If they can, and you have the other documents, they can reset it for you.

  • How do I erase and reset parental password?

    My 12yr old daughter set but doesn't remember the parental password on her ipod touch. How can I erase and reset everything?

    Two possible ways:
    - If you have a backup made without the Restrictions passcode, restore the iPod from the backup.
    - Restore the iPod to factory settings/new iPod.

  • HT4993 How do i unlock my phone if i forgot the simple 4 digit code

    How do i unlock my iphone if i forgot my 4 digit simple code

    Back it up and restore it using iTunes on the last computer you synced it with, as explained here: http://support.apple.com/kb/HT1212.

  • N900 - How to update software and Reset ALL data.

    If you have tried to reset an N900 from the settings menu on the device, you would have noticed it would have left all your data intact.
    Sometimes you want to start from scratch and delete all data in one go. 
    Here is how you do it.
    Its quite extensive, but comprehensive.
    From a windows PC
    You first need to download three pieces of software.
    The first software you need is called "Maemo Flasher", and this is the program that needs to be installed on your PC and can be found here:
    http://tablets-dev.nokia.com/maemo-dev-env-downloads.php
    Download the latest version of Maemo Flasher (which is currently 3.5 at time of posting this), and make sure you download the .exe file (maemo_flasher-3.5_2.5.2.2.exe).
    Install that file.
    Next you need the software for the N900 itself.
    That can be found here:
    http://tablets-dev.nokia.com/nokia_N900.php
    This page will ask you to enter your IMEI, with very clear instructions on where to find it.
    Follow the on screen prompts until you reach the download section.
    There are two pieces of software you need to download from there.
    eMMC content - This is the package to erase all data held on your 32GB storage.
    The Operating System.
    OS 2009
    PR 1.1.1
    PR 1.2
    There are, unfortunately, 3 different names for the OS.
    Latest version is "PR 1.2 version 10.2010.19-1".
    Download the latest eMMC package available, It's version 10.2010.13-2.
    The OS is a little more difficult to figure out which one you need.
    The notes alongside the software lets you find the right package easier.
    I found the best way to check is to do the following: (On the N900)
    Menu
    Settings
    About Product
    This will show you this image(or similar)
    Note the Version number on your N900's screen.
    Download the OS package that matches the Version on your device. As shown in the image above, using the red text as an example.
    For people that purchased the N900 in the UK, the OS package will probably be the same as the red text. But make sure you check.
    Software downloads complete.
    Place these two software packages in the following location on your PC.
    c:\program files\maemo\flasher-3.5
    You should now have two .bin files in the directory above.
    Next steps.
    Updating the N900 OS
    Your battery needs to be 100% full to prevent any crashes which could leave your phone dead.
    Turn your N900 off.
    Press and hold the U key on the keypad.
    Insert the USB cable (a USB symbol should appear on the top right of your N900 screen, and also the Nokia logo in the centre).
    You can now let go of the U key.
    On your PC: Navigate to the Start Menu and select Run.
    In the Run box, type: cmd. Then OK
    In the command window, type: cd\program files\maemo\flasher-3.5
    Type: flasher-3.5 -F RX-51_2009SE_1.2009.42-11.203.2_PR_F5_203_ARM.bin -f
    (the file name above may be different to yours, you will need to replace the filename with the filename of the software you downloaded).
    This image below shows the completed update of the OS, in the command prompt on your PC. This would have now removed any Apps you may have installed on the device, and reset the homescreens to how they were when you turned it on for the first time.
    Your personal data, such as Contacts, Images, SMS will still be on the device.
    So if you want to remove these aswell, follow the next steps.
    Resetting the Mass Memory
    Your battery needs to be 100% full to prevent any crashes which could leave your phone dead.
    Turn your N900 off.
    Press and hold the U key on the keypad.
    Insert the USB cable (a USB symbol should appear on the top right of your N900 screen, and also the Nokia logo in the centre).
    You can now let go of the U key.
    (If you have left the command prompt open on your PC from updating the OS in the previous section, ignore steps 5,6,7)
    On your PC: Navigate to the Start Menu and select Run.
    In the Run box, type: cmd. Then OK
    In the command window, type: cd\program files\maemo\flasher-3.5
     Type: flasher-3.5 -F RX-51_2009SE_1.2009.41-1.VANILLA_PR_EMMC_MR0_ARM.bin -f -R
    (the file name above may be different to yours, you will need to replace the filename with the filename of the software you downloaded).
    This image below shows the completed reset of the eMMC (32GB HDD), in the command prompt on your PC.
    This would have now removed any data you had stored there. Including Music, Photos, Contacts, SMS..
    The complete reset of your N900 is now complete.
    I hoped this has helped.
    My posts are my opinion and in no way the direct views of Nokia.
    If my posts are helpful, please give me some KUDOS using the green star on the left.

    Hmm, it's odd, because the wiki.maemo and another thread here say it works fine on 7. I have put flasher into xp compatibility, but the cmd box has no way to change it - at least, if it does it's through a back route that i'm unaware of.
    Attached the screen i see
    Edit: what "run" dialog box? is that the cmd box?
    Attachments:
    cmd.jpg ‏55 KB

  • How can i unlock my i phone 5

    hello
    how can i unlock my iphone 5.

    Not sure what you mean.  Is the phone lcoked to a particular carrier or is the phone locked up and you cannot use it?  Please give more information.

  • I have disabled ipod touch.. how can i unlock without resetting to factory default?

    i have a disabled ipod touch. how can i unlock with password without resetting to factory default?

    You can rstore from backup but you must restore the iPod
    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen                         
    If recovery mode does not work try DFU mode.                        
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings        
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up     
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload most iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store        

Maybe you are looking for

  • MAPPING USING FLAT FILE SOURCE MODULE

    I created a mapping using a flat file as source and a dimension as target, I've already configure both modules and their locations. When I try to deploy this mapping in the deploy manager, it generates the script for the control file and when I hit t

  • Final cut studio can't start (boot up)

    I can't start up my final cut pro when I switch on my Mac. I tried reinstall the program for many times, but still did not work. Can anyone tell me how to make it work again? Thank you.

  • Has Oracle published the source for frmwebutil.jar?  (Duncan?)

    After working with webutil for quite some time now, I recently discovered a problem. Before I give details, I must emphasize that I am running using the Java Plug-In (JRE 1.5.0_11) under IE 6.0, which is certified at level 3 (passes Forms functional

  • Flash drawing (outline) insights

    Does anyone have some insights on exporting vector drawings on Flash? I wanted to produce beautiful 256 color bitmaps like the character flo in the Diner Dash series, but I haven't found any luck. My bitmap is more jaggy and the outlines look terribl

  • IE browser windows crash at Flash player websites

    My computer seems to be running much slower at sites where Flash Player is used.  Myspace crashes/automatically closes very often.  I have downloaded Flash Player 10.  I have no idea where it is on my computer though.  I am using Internet Explorer 7,