HT4993 When i take a picture with my iphone 4s, with flash on the phone dies. Has anyone else experienced this? Does apple support this?
When I take a picture with iphone 4s the phone dies. I hold power button to power up. Thanks for any Help.
Apple Warranty should cover this hardware problem. You could try a Restore of the iPhone Firmware with iTunes on computer to confirm it is not software problem. Then make Genius reservation and take to Apple for resolution.
Similar Messages
-
I frequently have to remove and re-insert the SIM card in order to access the internet. Has anyone else experienced this? Is it a problem with the IPAD2 or with the SIM card?
Could be the SIM card, the iPad, or both.
Start with replacing the SIM card. -
I recently purchased the 16GB 5s. I didn't notice this before, but when I attempt to take a photo with the flash in the "on" position, the flash only works sporadically when I take a picture with the phone vertical. Anyone else with this problem?
I recently purchased the 16GB 5s. I didn't notice this before, but when I attempt to take a photo with the flash in the "on" position, the flash only works sporadically when I take a picture with the phone vertical. Anyone else with this problem?
-
When I got a new iPhone5, I experienced short battery life, and system sofware issues were not the cause. The camera also takes a blury picture regardless of lighting and I have the black one. Has anyone else experienced similar problems?
What makes you so sure it isn't software?
The camera can be focused by take the point of focus on the touch screen.
If it is new as you said, it should be under warranty. Make a Genius Bar appointment or contact Apple with a repair request. -
Since downloading OS X Yosemite I have been having issues with Netflix. Video slows down which causes the audio to go out of sync. Netflix plays ok on ipad which makes me think it's the software which is the issue. Has anyone else had this issue?
Try this:
Go to System Preferences - Bluetooth. Delete the keyboard from the list of devices by pressing the "-" button. Take the batteries out of the keyboard and reinsert them. In Bluetooth Preferences press the '+" button to add the new device. If the keyboard begins to pair, click the word "pair" and type in the passcode. Press return. The keyboard is now paired.
If the mouse is not pairing, try this: shut down the computer completely, unplug any USB mice, then turn off the power to the bluetooth mouse. ONce the computer starts up again, wait for the pop-up looking for a mouse. Turn on the power to the bluetooth mouse. It should work normally now. -
I am trying to use firefox as the web lauch for citrix ica client but when I go to login into remote site - I get the message waiting to find website but it nver finds the website. Has anyone else had this problem?
When I installed firefox, it asked if I wanted to use safari settings and I said yes but I think this might be causing the problem. Safari is no longer compatible with citrix ica client. When I reinstalled firefox it automatically installs the safari info. Does anyone know how to re-install firfox without installing safari info?Did anyone ever suggest you reset your PRAM?
http://docs.info.apple.com/article.html?artnum=2238
Also might want to try resetting the SMC, although I
doubt there's an issue there.
http://docs.info.apple.com/article.html?artnum=304123
I'm getting tired of people who supposedly know what
they're doing simply guessing that resinstalling the
OS might solve the issue. It's like trying to dissect
a frog with a sledge hammer, and wondering why you
didn't learn anything about anatomy in the process.
These sorts of things, although bizarre, should be
(and probably are) fixable without major surgery.
Thanks for the suggestion... but I think my first question would be why these parameters would need re-setting? This is a new machine... It has never been shut down hard. It is used at most 10 hours per week... mostly using Office 2004 for MAC. I need to figure this out as I will soon need it as a Cs2/CS3 - Aperture workhorse.
I too agree that it is best not to use a sledge when a scalpel is needed... but as a novice to the MAC world I may have been misled by Apple support. I seems to have fixed the symptoms ( some) but appears NOT to have addressed the cause... which is what I am after.
Would TechTool Pro detect a bad HD or RAM?
Thanks.... -
Hello all
I had my damaged unlocked iPhone 4 replaced by apple with a refirb model and am pretty sure they've issued me with a locked phone.
Has anyone else had this problem?
Is Apple aware that they are refirbing but not unlocking phones?
Cheers
TyIt is entirely possible that the human you spoke with at Apple simply made a mistake. You do realize that humans make mistakes, correct?
Take the device back to the store along with any documents you have stating it is or is supposed to be unlocked and let them clear it up.
This all assumes the device was unlocked by the carrier and not some shady website or local electronics store. -
Has anyone else experienced compatibility problems with the Tamron SP 70-300MM?
Is the lensora report based on actual testing... or merely theoretical?
I'm wondering ... because there's a well-established history of 3rd party lenses that should be compatible based on the mount, but have problems anyway when a new camera model is introduced that did not exist when the lens was designed.
At the same time, if you contact the lens vendor for support, they may be able to provide better data and sometimes they can re-chip or re-flash firmware into the lens to upgrade it to a compatible state.
Tim Campbell
5D II, 5D III, 60Da -
I purchased an iTune card and when removing tape number came off with it. Has anyone else experienced this problem?
See this support article:
http://support.apple.com/kb/TS1292
If you can't get to work after perusing that page - characters are completely missing, not just difficult to decipher - contact the iTunes Store Support; instructions are at the bottom of that article.
Regards. -
I am having problems copying and pasting clips from one project timeline to another. When I do this they often alter in length. Sometimes by two frames. Other times they lose a chunk off the end of the last clip in the sequence. Has anyone else found this?
You need to give a lot more information about the media specifications and the project properties you're using in the different projects.
-
Changed group membership in WGM 10.6.3 from the 10.6 server. The change takes overnight to work. Formerly ran WGM from my 10.6.8 mac (worked perfectly) but now I am at 10.7.5 and must use WGM on the server. Has anyone else seen this behavior?
Hi
"Changed group membership in WGM 10.6.3 from the 10.6 server. The change takes overnight to work"
If I've understood you correctly I've never known this or anything else to take that long? What were you trying to do exactly?
"Formerly ran WGM from my 10.6.8 mac (worked perfectly) but now I am at 10.7.5 and must use WGM on the server. Has anyone else seen this behaviour?"
http://support.apple.com/kb/HT1822
HTH?
Tony -
3 year old iMac 24 running OS 10.7.4. After it has been on for a day or so, it stops going to sleep and becomes very slow. This only happens when Safari is running. Quitting Safari solves the problem. Has anyone else have the same problem? Does not happen on MacBookpro only on iMac.
Hello Albert, see how many of these you can answer...
See if the Disk is issuing any S.M.A.R.T errors in Disk Utility...
http://support.apple.com/kb/PH7029
Open Activity Monitor in Applications>Utilities, select All Processes & sort on CPU%, any indications there?
How much RAM & free space do you have also, click on the Memory & Disk Usage Tabs.
Open Console in Utilities & see if there are any clues or repeating messages when this happens.
In the Memory tab, are there a lot of Pageouts? -
just tried using my headphones for the first time while at the gym, i had to hold the headphones in and when id let go, no sound would come out of the headphones and the music would pause, has anyone else experienced this problem?? im assuming its a hardware problem?
nevermind, i had to press it in real hard for it to click down, was scared to do so before, didnt want to break it. UGH.
-
Has anyone else experienced problems with the disc burner/driver software not being found?
I am trying to burn music onto a disc and it is telling me that the disc burner/driver software has not been found. Has anyone else experienced this with their MacBook Pro?
SuperDrives wear out - it seems that yours might be on the verge of a mechanical failure. I'd just replace it, buying a new drive from Other World Computing and installing it yourself (because Apple would charge a small fortune).
Clinton -
iPhone 4S problem: Speaker only makes 'electronic noise' with incoming calls.. Has anyone else experienced this problem ?
I've not experienced this. But I do appreciate your asking.
Did you want help with your technical issue? If so, why don't you ask. Also state what troubleshooting steps you've taken.
Maybe you are looking for
-
Hi I'm extracting the data in R/3 system using tcode RSA3 for transaction datasource (2LIS_02_ITM). When i extracted the transaction data , it was giving time out error. Then i went into debug mode to find the error. While debugging the code it gave
-
hi friends , need help in uploading the file on the server and storing the path of the file while inserting to the database . I have the code with me but that is limited to the one content type i.e text or doc format . I am noit getting as to how sho
-
X58 Pro BIOS Crash during Boot
Hi All, I have recently assembled a system with X58 Pro board and Core i7 920. It was working fine for 3 months except that it started having BIOS crashes since last night. The issue is that the mainbaord lights would be on without the POST screen an
-
Archive docuemnt is not viewing through VF07 tcode
Hi Experts, There was one issue regarding archive documents, if any body have the idea plz let me pass your views. My user is running the transaction VF07 to view the Archived documents , but getting the error with " no billing document doesn't ex
-
Unable to enable GPU rendering in Project Settings (CC 2014)
I have two GTX 580s installed and the option for GPU rendering is grayed out in the project settings dialog box. Any ideas on why that is and how to fix it?