HT5219 Can I connect my thunderbolt monitor to my MacBook Pro and iMac at the same time

I am wanting to connect my thunderbolt monitor to my MacBook Pro as a secondary monitor when running programs in windows 7 thru boot camp, and also have it connected to my iMac as a secondary monitor when working thru apps on my iMac. Is there a way to do this without having to connect and disconnect cables each time I want to switch.

I don't think it can be done without a KVM switch, & not sure they can handle that resolution.

Similar Messages

Can i use a thunderbolt display for my macbook pro and hp laptop with windows 7 and what adapters will i need

Can i use a thunderbolt display for my macbook pro and hp laptop with windows 7 and what adapters will i need

Hi jayhrab,
Currently, the system requirements listed for an Apple Thunderbolt Display are:
Thunderbolt-enabled Mac computer, including MacBook Air, MacBook Pro, Mac mini, and iMac
OS X v10.6.8 or later
Apple - Thunderbolt Display - Read the tech specs.
Regards,
- Brenden

HT5219 how can I connect two thunderbolt monitors to my macmini in windows 8 and bootcamp? Works fine in OSX

how can I connect two thunderbolt monitors to my macmini in windows 8 and bootcamp? Works fine in OSX

Did you try to hook up both monitors to the Belkin adaptor? Trying will determine if your monitor has a bad input port. See if the Belkin adaptor is the problem. I have never used that specific adaptor, but I have always had luck with the Dr. Bott's DVI for ADC adaptor. Best of luck.
www.drbott.com

I want to Connect my Mac Mini as a Slave to a Mac pro Server while at the same time using the Mac mini's thunderbolt ports peripherals ( ie monitor, Sound Card, Hard drives) Creating a poor man's new mac Pro. Can this be Done?

I want to Connect my Mac Mini as a Slave to a Mac pro Server while at the same time using the Mac mini's thunderbolt ports peripherals ( ie monitor, Sound Card, Hard drives) Creating a poor man's new mac Pro. Can this be Done?

Well, I really would love the new unreleased mac pro however , I'm not sure of the expected cost , Everyone speculates from $3,000 to $8,000, in which I may have to wait a while to purchase.
To the point .... I want fully functional thunderbolt ports to be on the current mac pro's .... wonder if anyone had workarounds yet?... or could I chain the the current mac pro to a mac mini to make that happen?

How do i connect three external monitors to a macbook pro?

How do I connect three extrenal monitors to my Macbook Pro?

I have a USB to DVI adapter from kensington. I use to use it to power at 14" display.Moving windows around had some tearing and lag. Typing lagged, but it was use-able. It was fine for displaying diffrent stats. The OS treated it as it would any additional display.
But I found it undesirable for any thing tha requires lots dragging and clicking.
Every so often the device would lock up. At witch point the computer would get stuck trying to detect the USB display. I would have to unplug the adapter, cycle the power on the adapter. And then it would be good for a couple more months.
Also some times after a reboot, the adapter would stop working. I would have to unplug it, and login, and then plug it back in.
Coping file to my USB 2 harddrive seemed to cause more lag to the USB to Video Adapter.
About the idea of dasiy chaining 3 Thunderbolt display tgeother. Apple Thunderbolt Display (27-inch): Connection options for Thunderbolt Macs states the most the current MacBook Pro 15 & 17 inch can currently drive is 2 Apple Thunderbolt Displays.

I connected an external monitor to my MacBook Pro, but it doesn't open any programs. It Just sits there with a blank screen. How do I get it to open programs and act like a monitor?

I connected an external monitor to my MacBook Pro, but it doesn't open any programs. It Just sits there with a blank screen. How do I get it to open programs and act like a monitor?

Dear Jean:
It sounds like you are trying to get your external monitor to act as the primary viewing screen. For example it would have your Doc, Icons, Etc. In order to make the external monitor the primary screen you have to:
Open System Preferences.
Choose the Displays Icon
There will be several tabs to choose from pick Arrangement
Drag the toolbar to desired display
Let me know if this helps at all!
Lance

Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.

Hi!
Didn't know exactly where to direct this question in the Apple Community so I chose Airport. To everyone, thanks in advance.
I’m really desperate. I’m a big Apple fan. I have two Apple MacBook Pro laptops with Mountain Lion software. I also have an Apple Airport Extreme. My HP Photosmart C4780 printer was also purchased from Apple. Anyway, my Internet service is AT&T. AT&T just upgraded my service with a new modem/router (AT&T U-Verse). Prior to the conversion, my wireless printer connection was working perfectly.
Now can’t print wirelessly. For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed. Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works. Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
This appears to be an HP printer problem. I went to HP community support with the information below but I have received no solutions outside of buying a new printer.
“Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly. The Diagnostic Summary in brief: Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail. Nothing else under diagnostic summary ran. Under Configuration Summary: It shows old SSID name and Mac Hardware Address but no IP Address.
Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless. It shows status – disconnected. Under general information it states the following: Network status - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0.”
To be straightforward, I’m no computer tech so I don’t know what this means or where to find. The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve tried everything to reconfigure without success. If I need to make these changes via Airport Extreme Utility 6.0 not easy to find not that I know what I’m doing.
Most importantly if I ever get wireless working again, do I still need Airport Extreme connection or is the AT&T U-Verse modem/router sufficient?
Any direction or help is greatly appreciated. Thank you for listening.

Thank you for your prompt response. I'll be honest I'm a retiree and a newbie to all of this stuff. I don't even know how to do a thread. (Embarassing) This is my first ever contact with the Apple Community so I'm slowly trying to figure this out as well.
As to your thread request, I'm assuming you want to read my post with HP. Not knowing how to thread, I've copied it below.
I have an Apple MacBook Pro laptop with Mountain Lion software. I also have an Apple Airport Extreme. My Internet service is AT&T. AT&T just upgraded my service with a new modem/router (AT&T U-Verse). Prior to the conversion, my wireless printer connection was working perfectly.
Now can’t print wirelessly. For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed. Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works. Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly. The Diagnostic Summary in brief: Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail. Nothing else under diagnostic summary ran. Under Configuration Summary: It shows old SSID name and Mac Hardware Address but no IP Address.
Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless. It shows status – disconnected. Under general information it states the following: Network status - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0
To be honest, don’t know what this means or where to find. The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve read your forum and tried everything to reconfigure without success. Any direction or help is greatly appreciated.
Thanks in advance!
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
I finally figured it out! (Sorry that I'm replying to my own posts btw, but I want to post the solution for anybody else with the SigmaplusEOL1 problem). If you have the SigmaplusEOL1 as your SSID when you print the "Wireless Network Test Report", you do NOT need to return it (I know that's hassle for people). To fix the problem, follow these steps.
1) Unplug your printer.
2) Go to your router's IP address (like 192.168.1.1 or whatever it is for your router).
3) Change the SSID of your wirelss network to "SigmaplusEOL1".
4) For the Security option for your wireless network select none (so that a password is not required to access your wireless network).
5) Power your printer back on and reprint "Wireless Network Test Repor". It should say "No problem found..."
6) The report should also have a the IP Address of the printer (under Configuration Summary at the bottom). Type that IP Address in your browser to get to the printer's settings page.
7) Click the "Network" Tab at the top.
8) Under the "Connections" header in the left pane, click "Wireless (802.11).
9) Click "Start Wizard" at the bottom right.
10) In the wizard, change the SSID and encryption (wep or wpsk) password to whatever you want your wireless network to be. So probably whatever it started out as before you changed the SSID to SigmaplusEOL1
11) Click "Finish" at the end. The page will probably try to keep loading but it won't because you changed the network settings of the printer. Just ignore that
12) Go back to your router's IP address and change the SSID and encryption password to whatever you changed the printer's SSID and password to.
13). Reprint the Wireless Network Test Report. It should say the SSID is the same as your wireless, and everything is good.
That's it. You should be good to go now.
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
Thank you for your prompt response. This has been a totally frustrating experience. I’ve spent at least 8 hours trying to fix this. My HP problems and your initial steps were identical to mine. I am by no means a tech person and my computer tech knowledge is minimal. However I followed your steps to the best of my ability.
I did get the SigmaplusEOL1 message. I was able to get to Step 6 where the wireless network test report now reads – “HP printer settings do not match your wireless router settings.” So I guess this is a step in the right direction. However unfortunately the Configuration summary message for the IP Address reads – “Not Applicable”. (Note: changing SigmaplusEOL1 to network name knocked out my Internet access. Had to switch back to regular network name to regain access.)
I’m at a loss as to what to do next.   Without the IP Address is it possible to move forward? As I stated earlier, I’m not a tech person. As to your steps 7, 8 and 9, I can’t find them on my computer or maybe I’m looking in the wrong places. In System Preferences - Network, I have none of these steps. If you’re referring to Airport Utility, with the changes in Mountain Lion, these steps are no longer there. If you’re talking about Safari, Firefox or HP, now I’m really lost.
Finally, I don’t know if you can answer this or not. If I ever get wireless working, do I still need Airport Extreme or is the AT&T U-Verse modem/router sufficient?
Again thank you for your time and patience.
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
Unfortunately I am unable to offer any further advice as I only followed the instructions listed on the other page.
Finally, as to having WEP enabled, I don't know. Don't even know where to look. The best that I could determine is that my security is WPA/WPA2 Personal.
I'm truly sorry about all of this. Thank you for your time and patience. After reading all of this and you change your mind, I would understand.

Can a mac mini be set up to run two separate users at the same time?

I work for a middle school and we need to purchase 20 computers that will just be used to run internet apps. Though we have all Macs, we don't have a big budget and for this one use only, we are condsidering purchasing inexpensive HP all-in-ones for about $450 each. However, I was wondering if a Mac Mini can be first set up with 2 partitions, install the OS on both partitions, then run two different users, with two separate monitors and keyboards, at the same time? This way, instead of purchasing 20 Windows computers, we could purchase 10 Mac Mini's (and displays) and save money, and still be supporting just one OS throughout the campus.

If you setup a server, as in the Mac OS X Server Installation, pages 23ff show configurations, you can have multiple users, but they must all have computers. Some installations can be done with dumb terminals but that is not what you seem to want. Unix machines do have a multiple simultaneous user capability but you still have to have a computer for each user, again, not what you seem to want to do. Right now there are two other users logged in on my Sun workstation on the desk behind me...they are logged in because I permit them to do so.
And last night for an experiment I connected my iMac and MBP by ethernet wire, logged in on the iMac, then logged in on the MBP and from there on the iMac...but I set up the network to permit that and then disabled it again. You can create security holes doing things like this.
As dwb points out switching from Apple to PC equipment is a false economy that lures in administrators. In our county school system we had a superintendent who hired a good friend...who had PC-industry ties. Decided to remove all Apple equipment from the elementary schools and switch to PCs. It wasn't long before they ended up going on a 4-year cycle of "refreshing" the equipment, i.e., completely replacing all hardware in every school on a four year cycle. Since my wife was a Media Specialist, aka librarian, and responsible for technology in her school, every four years she had to develop a complete school map of where each teacher wanted the computers in their classrooms, complicated by where the technicians predetermined the locations of the network wire drops, of course. then teachers get shuffled over the summer and all the plans are for naught.
Anyway, there really isn't a solution to your problem except to buy a large number of computers and let each student use one and have them networked to a server, print server, printers, etc. This is not inexpensive and cutting corners will only cause headaches for you.

My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

OK great info!
I found 2 possible ethernet to USB adapters:
By "Plugable": USB 2.0 to ethernet LAN wired network adapter - seems this will work, but I'll contact Plugable.
2. Apple USB Ethernet Adapter
Easily connect your MacBook Air computer to an Ethernet network with the Apple USB Ethernet Adapter. Small and light, it connects to the USB 2.0 port of your MacBook Air and provides an RJ-45 connector that supports 10/100BASE-T performance. BUT NOT SURE IF THIS WILL WORK ON ANYTHING BUT a MacBook Air…
One person commented:
This little gem used to be the device of choice for adding a second Ethernet interface to a Mac Mini Server and I'd been using one that way for about a year. After doing a software update to 10.6.6 it stopped working. Forewarned is forearmed – it appears that Apple is finally enforcing the MacBook Air system requirement.
Thanks for any additional comments.
Best regards,
Steve Schulte
Sunday 6 January 2013

My SB Audigy 2 card can't use headset and musicamplifier at the same time

Hi, i just bought a SB Audigy 2 [D400] and i have downloaded drivers and programs. I run Windows XP SP2.
The soundcard works fine but it is very very annoying that i physically have to change the jack in the green=line out jack from headset to musicamplifier when i want to use my musicamplifier and change back the jack in the green=line out from musicamplifier to headset when i just want to use the headset/headphones .
In the shop they told my that i can connect both amplifier and headset at the same time and then with creative software control whether there is sound in the headset or in the amplifier. But i can't simple get it work.
I tried to use the green to the amplifier and the headset/speakers in the black (line out 2) and then with creative speaker settings softeware choose headphones but still the ampliefier receive the sound and no sound in the headphones. Why? In fact no matter what configuration i try the headphones doesn't work.
But if i change the jacks so headset is in the green line out then only headset is working and the amplifier doesn't work no matter i put it in sort=line out 2 jack or orange=line out 3 jack.
Can somebody here tell me if it is possible or not to connect both headset and external amplifier and control by software which to play? and how?
please help, thx.
Michael

If you can have an ASIO compatible music playing system, then it might be possible to have system like you wish when using Creative Audigy 2 card. Since ASIO bypasses Windows Audio System, you can use both 'drivers' (ASIO - WDM/MME/DS) side by side.
Say you want to play a game (using headset /w mic) and someone other like to listen music at the same time. With ASIO capable system you can output your music for example to "center L/R (stereo) channels" and same time output sounds from other source (using MME/DS/WDM drivers) to normal output channel (Front L/R). Only thing is, you need to set your speakersystem to 4 or 6 (depending which other channel you're using) (and for better 'balance' to adjust "angle" on THX console. You get the THX console by installing Audigy 2 Zs software).
Try for example http://img332.imageshack.us/img332/463/djs9mo.jpg[/img] width="406" alt="Image Hosted by ImageShack.us" >
Another option:
Say you want to play music through external amplifier and play game online with your headset + microphone (eg. others but you listen the music, you play games)
--> try free http://img332.imageshack.us/img332/4589/tbp7rz.jpg[/img] width="406" alt="Image Hosted by ImageShack.us" >
If you use ASIO on BeatPort Player you can select L/R individually from the list(s). Same rules as described earlier.
= You can play from 2 different sources simultaoneusly (ASIO + WDM/MME/DS) to two different outputs without disturbance. The other (WDM/MME/DS) source is set 'automatically' output to (Audigy) "green" port, and the other (ASIO) to "black" or "orange" port (as set).
.jtpMessage Edited by jutapa on 09-5-2005 05:30 AM

Wi-fi connection on HP Deskjet 2540 and network at the same time?

Hello
Please can you tell me how to keep my connection to my wi-fi printer whilst connected to my Virgin Media Broadband? Every time I want to print I have to switch off the Virgin network connection and connect to the HP Deskjet Wi-fi, and then switch it back again to Virgin to browse or send emails.
Thank you for your help
AC33

Hey there @AC33 Welcome back
I understand you are looking to install your printer on your network, so you can use the internet and printer at the same time. By the sounds of it, you may be connecting the printer currently, using the Wireless Direct feature, which will only allow you to connect to the printer or the network at a time. Basically, the printer is acting like a network.
Here is a link for you to check out. It will help you install the printer on your network:
Setting Up the Printer for a Wireless network for the HP Deskjet 2540 and HP Deskjet Ink Advantage 2...
I hope this helps you, let me know the outcome
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Can WRT54G use WPA and WEP at the same time?

I used to have a smc 802.11b wireless router and a dlink 802.11b wireless print server.
In order to have WPA and a firewall, I replaced the wireless router with a linksys WRT54G.
Then I realize the dlink print server, even though it has the "g" keyword in the model name, does not do WPA (DP-G321).
Do I have to buy a 802.11g wireless print server? Or is there another solution?
I don't supposed the linksys router can do both WPA and WEP at the same time?
Connecting the print server to the router with a cable is not feasible. They are on different floors.

both of your devices are has a wireless b technology settings, just set a wep encryption on your network rather than wpa because some wireless b devices don;t work with wpa. with regards to your query if wep and wpa can be used at the same time, the answer is no.

How can I delete photos from my iPad, iPhone, and laptop at the same time?

How can I delete photos from my iPad, iPhone, and laptop at the same time so I don't have to do it separately on each device?

Photos that were synced from your computer using iTunes can only be deleted by de-selecting them from the folder from where they were synced - and then re-syncing.
Connect the iPad to the PC and launch iTunes.
Click on the iPad name on the left side under devices.
Click on the Photos Tab on the right.
If you want to remove all of the Photos - uncheck the Sync Photos from Heading
Click on Apply in the lower right corner of iTunes
If you are using iTunes 11 - this will be helpful, Setting up syncing in Windows.
http://support.apple.com/kb/PH12313

I have the IPhone, IPad and MacBook, IPad and IPhone share the same Apple ID and Icloud storage. Cannot make ID Change on MacBook as it says the ID is already taken. How can I make all three match?

I have the IPhone, IPad and MacBook, IPad and IPhone share the same Apple ID and Icloud storage. Cannot make ID Change on MacBook as it says the ID is already taken. How can I make all three match?

The problem is that all services are bundled with your Apple ID ([email protected]):
Your iCloud account (Mail, Contacts, Calendars, Reminders, Notes, Backups, etc.),
also iTunes & App Store purchases (Music, Movies, TV Shows, etc.),
and the iTunes Match services.
(I guess that all your devices - yours and your wife's are connected to one iTunes library, right?)
If you want that your wife gets her own iCloud account for Mail, Contacts, Calendars, etc. but gets also access to your media then you have two set up two things on her device:
iCloud (Settings > iCloud) with her account (e.g. [email protected])
and
iTunes & App Stores (Settings > iTunes & App Stores) with your account (e.g. [email protected]).
In this case she gets access to your library and could use the same iTunes Match account.
(See also: Using one Apple ID for iCloud and a different Apple ID for Store Purchases http://support.apple.com/kb/HT4895)

Connecting USB and Charger at the same time

Hello guys, Is there any problem connecting usb and charger at the same time? after that, the Nokia Battery Monitor 2.0 shows 93% after full charge. Any ideia?

yes, there is a male-female usb extension cable sold on computer store.
Just pick up the length you need.
But the price is almost the same with the cheapest 2.0 usb hub (4 port), so you better consider the usb hub one.
Good Luck.

HT5219 Can I connect my thunderbolt monitor to my MacBook Pro and iMac at the same time

Similar Messages

Maybe you are looking for