HT5815 my macbook pro 15 inch 2.2 does not start up anymore after update, even after shift V.

after installing the update the machine rebooted. But only the apple logo en circle appeared. and then....stuck.
a hard shut down and reboot with Shift hold down until the bar did get it in safe mode (or was it the command V) but it freezes there....

Another post did add some light to it too.
Finally my mac started up. Backing up now. :-) tnx
Kappy Tampa, FL and Vancouver, BC
Re: PROBLEMS WITH 10.8.5
Sep 13, 2013 10:43 PM (in response to papanast)
You might try this:
Repair the Hard Drive and Permissions - Lion/Mountain Lion
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Then download and install: OS X Mountain Lion Update v10.8.5 (Combo).

Similar Messages

I bought 2 new memory card to 4 grams each - replace them in your MacBook Pro 13-inch but it will not turn on - If you are installing a card for 2 and one for 4 d all works - tell me what could be the problem

I bought 2 new memory card to 4 grams each - replace them in your MacBook Pro 13-inch but it will not turn on - If you are installing a card for 2 and one for 4 d all works - tell me what could be the problem

I assume that you have installed new RAM in your MBP.
It would be helpful if you indicated the EXACT model/year MBP that you have.
What the the RAM specifications that you are trying to install?
Ciao.

My macbook pro 13-inch, Late 2011, is not charging properly.

My macbook pro 13-inch, Late 2011, is not charging properly. it charges for 4-5 seconds then stop and then continue. It charges normally when turned off. Could anyone care to explain what the problem is?

Hi OneManArmy_,
Thanks for using Apple Support Communities. I would try resetting the SMC and seeing if that allows the charge to work when the system is on:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
Cheers,
- Ari

Ever since last night my macbook pro 13 inch has been doing weird and not so wonderful things.

Ever since last night my macbook pro 13 inch has been doing weird and not so wonderful things. It will only power up with the power pack attached as soon as the battery pack is removed my lappy goes dead. The charge icon shows when its connected. Also if the lid is shut while it is still operating and not been shut down it completely shuts down, whether or not it has been shut down properly it takes 4-5 attempts of opening and closing the lid to get it to start up. It only seems to restart with the lid closed and only reason I know it has is because the apple icon lights up. When I finally get it started up the clock has reset itself back to 2008, requests for internet access pops up, outlook is not allowing me to delete emails, etc. Help!!!
TIA
Amethsytfyre

yea man you need to take it to the Apple store ASAP. This is why I bought the Apple Care warranty when I bought my Macbook pro. At the Apple store they will trouble shot your problem and if it cant be fixed you may end up with a new lappy toppy good luck my friend, hope everything goes good, and your partner isn't to badly damaged

I can't install my old logic 8 on my new macbook pro. It says it does not support powerpc applications anymore. what do i need to do?? this is ridiculous!!!

I can't install my old logic 8 on my new macbook pro. It says it does not support powerpc applications anymore. what do i need to do?? this is ridiculous!!!

Logic 8 will probably run on your new machine but the installation program contains some older PPC code for pre Intel Macs. This was not a problem as all OSX versions contained the "Rosetta" PPC emulation, that is, up until Lion when all PPC emulation was dropped.
There are ways to do this however, try searching Google for: Installing Logic 8 under Lion or Mountain Lion.

HT201343 I just verified that i have an early 2011 Macbook Pro and the airplay icon does not appear. i also have a 2013 Macbook Pro which shows the airplay icon. do i need to enable airplay on my early 2011 or is there an update that is needed? Confuse

I just verified that i have an early 2011 Macbook Pro and the airplay icon does not appear. i also have a 2013 Macbook Pro which shows the airplay icon. do i need to enable airplay on my early 2011 or is there an update that is needed? Confused.

To check your model go to About This Mac (by clicking on the Apple icon, top left) and then select more info. If you wish to use mirroring you will need one from 2011 or later running OSX 10.8 or later. The alternative would be to use 3rd party software like Airparrot.
About AirPlay Mirroring in OS X

My MacBook Pro, running 10.7.3, does not recognize when my iPhone and iPad are on the same network, thus it does not synch. Any ideas?

My MacBook Pro, running 10.7.3, does not recognize when my iPhone and iPad are on the same network, thus it does not synch. Any ideas?

Try the basics first:
Change your router channel number. Most times this works & is all you have to do.
Disconnect & reconnect your modem. unplug it for about 10 seconds. Plug it back in. Do the same for Apple’s routers. Wait for everything to reboot.
System Preferences>Network
Click the Assist Me button.
In the next window that pops up, click the Diagnostic button & do the necessary.
Research Knowledge Base for network problems that pertain to the OS that is currently installed on your computer. See these basic networking KB Articles: http://support.apple.com/kb/HT1401 AirPort troubleshooting guide
http://support.apple.com/kb/HT2712 Using network locations in Mac OS X
Manually provided DNS server addresses are higher priority than DHCP's
http://support.apple.com/kb/HT1714 Solutions for connecting to the Internet, setting up a small network, and troubleshooting
============================
What to do when you can't connect to the Internet
Also, run the Airport Utility app which is located inside the Utilities folder.
=====================
If using a Linksys router, contact LinkSys Customer Support and/or post in their forums.
If using Apple's Airport, please re-post over in one of the AirPort Forums.

I am trying to install a brand new WD 500 gb sata internal hd in my macbook pro. the original install dvd does not recognise the hd. all hardware is ok. any help?

I am trying to install a brand new WD 500 gb sata internal hd in my macbook pro. the original install dvd does not recognise the hd. all hardware is ok. any help?

For some reason OS X disks (whatever edition or flavors) that are supplied with Apple products only seem to contain a limited knowledge of available hard drives on the market at the time of thier publishing. This (rather opportunistically) creates a "Best Before" stale-OS X-software-copy situation where upgrading to or replacing a defective internal SATA hard drive with a newer, better or larger one is a largely hit and miss affair.
If you buy the latest and greatest disk drive available for any older Mac you are likely to run into unresolvable problems making a clean re-install of your own, old edition or flavor of OS X onto any newer or larger hard drive since the OEM (gray) "OS X Install Disks" that Apple supply with retail products seem to contain only time-sensitive lists/mapings of then-known target drives that the Drive Management Tool in the then-published old "Installer Software" will support.
Presumably new (colorful "X") retail versions of OS X (10.whatever.whatever) also contain time-limited Installers with limited knowledge of and adaptability to/compatability with a limited number of old hard drives then kicking-around on the market.
This is especially a problem nowadays since the countless "puny old" hard drives that have been on the market are largely obsolete in a few months time, as manufacturers continue to produce larger and cheaper units, discontinuing older puny products... So if your drive fails you need an exact old (or similar familial) replacement drive for your "backup copy of OS X" to do a fresh, clean OS X re-install. Otherwise you need to purchase a new retail version of OS X, since yours is now effectively obsolete. Purchasing an old, puny drive to re-install your version.flavor of OS X to avoid buying a new version of OS X is a rather false economy.
If you still have a working old hard drive with your old polluted 10.version.flavor of OS X still working on it you apparently must clone it with Time Machine or the newest version of Disk Utility (disk image copying) to most newer, larger drives, and a clean reinstall to such new hard drives is not possible.

MacBook Pro 17" (mid 2010) desktop does not fill entire screen

Hi,
First of all I apologize for posting such a long question but in order to best describe the problem I am having with my MacBook Pro, I had to mention every detail.
I recently installed windows 7 x64 home premium on my new MacBook Pro 17 inch (mid 2010). After successfully installing the Bootcamp drivers (version 3.1) I have noticed that my screen resolution has become slightly smaller than before. There are half an inch thick black bars on the right side as well as on the top of the screen.
This problem is not limited to windows, I'm having the same problem in mac osx after the windows 7 installation. Even on the start up gray screen.
I have tried almost every trick in the book, adjusting the screen resolution from the display settings menu (which by the way are on 1920x1080), checking all the settings on the nvidia control panel, resetting the SMC, resetting the VRAM, running the hardware diagnostic test (short as well as the long one), formatting the windows partition, formatting the Mac OSX partition then performing a fresh install of both. So far, I have been frustrated with failure.
After trying my best to resolve this issue on my own, I tried my luck with apple support. The customer representative was very helpful and listened carefully as I explained the problem to him. He asked me first to check for any available updates on my mac osx as well as in win 7. I told him that I had already installed every available update in both the OS's. He then asked me to reset the SMC and after that to reset the VRAM. Even though I had already tried this, I still gave it another shot but that didn't help.
Since my MBP was still under the standard warranty, (I have also purchased the Apple Care Protection Plan) he asked me to take it to an Apple Authorized Service Provider. I took his advice and went to the nearest AASP. The Apple Engineer over there performed the same steps, adjusting screen resolution, resetting SMC and VRAM, but even he was not able to resolve this problem. He suggested that I should get my graphics card replaced or if required upon inspection, the logic board replaced. To be very honest, I was very skeptical about his suggestion as the laptop is brand new, hardly 2 months old. How is it possible that there could be a problem with the hardware? I asked him whether it is possible to restore the firmware of the graphics card as the problem could be software related. He said that Apple have not started issuing firmware restoration CD's for the latest mid 2010 MBP's so a firmware restore won't be possible. My best bet would be to get the graphics card replaced or the whole logic board replaced.
So you see, I have been down almost every possible road which could have lead to resolving this issue but unfortunately I am stuck with it. I hope any of you could offer a different approach in order to get rid of this annoying problem.
Any help would be highly appreciated. (Trust ME!!!)
PS: I have also posted this question on the Bootcamp forums page. Since the problem is not limited to windows 7, I decided to post here as well.

UPDATE: I just came back after a visit to the apple service provider here in New Delhi. They have replaced the logic board on my macbook pro and guess what? the situation is still the same. No difference what so ever as far as the screen resolution is concerned. I can still see those black bars in the exact same places i.e. the right hand side as well as on the top of the screen. Even the size of the black bars are still the same.
I am so upset right now. After trying my best in order to solve this problem I went to the AASP with high hopes. I was very confident that after replacing the logic board this annoying problem would go away but unfortunately that's not the case. Even the Apple Engineer was clueless on how to solve this problem.
I think I'll call apple care and speak to the customer relations regarding a replacement.
If any of you can come up with a solution to this problem please let me know.
I'm all ears!!!

MacBook Pro 13-inc, keyboard backlight does not work

My keyboard backligth does not work.
I have a MacBook Pro 13-inch, early 2011 with MAC OS X Lion 10.7.3.
I already set the preferences to be on in autmatic mode with low ligth on but this did not work.
When I turn on the computer the keyboar lights on but as soon as the computer finish the log on the keyboard goes off.
I will appreciatte any advise.

Powerplan works great!

My 2011 MacBook Pro does not start and stop after the apple appear, they said that the problem is a video problem and need to change the logic board. Cost almost same to buy a new one. Somebody have the same problem?

I have a MacBook Pro early 2011. Does not start. After the apple show, a blank screen appear. The service said that the problem is with the video plaquue in the logic board. Need to change. Cost lmmost the same than a new MacBook Pro. Somebody has the same problem? What we can do?

I hate to break this to you, but life isn't fair. If your job is that critically in need of a computer, then you should have a spare to use for just this kind of situation or have your employer provide you with a computer to use.
Computers break down, just like cars. If your car breaks down do you curse the car maker or get it fixed? Surely, you paid more for your car than the computer.
This is reality. Best get used to it because it won't get any better.

Acrobat Pro X 10.1.10 Does Not Start Windows 8.1

I have Create Suite CS6 which apparently bundles Adobe Acrobat Pro X. I have upgraded to 10.1.10. Under Window 8.1, this version simply does not start. There is no startup screen. There is no error in EventViewer of Windows. It simply does NOTHING.
I went to Windows Program and Features and did a "Repair" on Acrobat Pro X. This redid the install but the result is the same.
Is there a known compatibility issue here? How do I work around this?

Hello,
Have you tried to run the Acrofix patch on your computer?
If not, please follow this link, http://helpx.adobe.com/creative-suite/kb/acrobat-failed-launch-30-days.html
Regards,
Yuvraj.

My Mac Pro (1,1 Intel core) does not start up and the white light is blinking

Mac Pro does not start up, the white light is blinking. I check the conexion with the monitor and tried the monitor on another Mac Pro (5,5) and work correctly

When the Power light blinks in a deliberate pattern at Satrtup, that indicates not enough RAM, in full working order, is available.
You will need some known-good RAM to make progress.

Macbook pro default maximum screen size does not cover the bottom inch

Kind of frustrated by my new macbook pro.
At the bottom of the screen, there's the icon bar (icon dock), which is about inch height. I adjusted it to smaller size, about half inch. This is what I did, not sure if related to my problem.
At the beginning, I thought it was Safari's problem. Later I found all programs has the problem. I'll use Safari as example to describe the problem though.
When I open Safari, it does not expand to the bottom inch of the screen, as if the icon dock prevents it expanding to the icon bar area of original icon bar size (i.e., inch, not half inch I'm using), and as if there was a line at the bottom inch. I click the plus sign (maximum screen), it still leave the inch uncovered. However, if I use full screen modle, Safari would covers the whole screen.
when not in full screen model, I can drag the bottom edge of Safari, but can only drag to the virtual icon bar line (at bottom inch position). When bottom edge is at the virtual line, the drag arrow is single direction pointing to up. However, I could move Safari to lower and cover the bottom inch area (with icon bar on the top), and then drag the top edge to make it cover all screen area.
What makes more annoying is if a new tab automatically opens, Safari will goes to the size with the bottom inch uncovered. This problem does not happen if program runs in full screen model.
I tried a few programs, all have such problem. Looks to me default maximum screen size excludes the bottom inch (because by default that area is supposed to be occupied by icon bar although I changed the size or just simply hide the icon bar).
Anyone know why? How to solve the problem? TIA.

called Apple, the solution is:
1, turn on sound
2, shutdown
3, press and hold these four keys the same time: left option, left command, R, and P
4, press and release power button to restart
5, after first starting chime sound, continue hold those four keys
6, after second starting chime sound, release keys
this resets some settings --- not sure what is reset though.

My mid 2010 MacBook Pro 15 inch unibody battery will not accept a charge

HI there one and all!
                                    My mid 2010 MacBook Pro 15" unibody laptop will not accept a normal charge using the mag safe cord. I have replaced the original battery with a factory new replacement, but I still have the same results.
    The computer powers up and runs only with the mag safe cord attached and when shut down, does not switch from green to orange to indicate the charging mode.
    Can anyone be of assistance or perhaps has had a similar issue? Thanks in advance to anyone for their insight and help. If it makes a difference, my computer information is as follows: MacBook Pro 15", Mid 2010
                                        Processor 2.66 GHz Intel Core i7
                                        Memory.    4 GB 1067 MHz DDR3
                                        Graphics. Intel HD Graphics 288 MB
                                        Serial number. W80---------------
                                        Software     OS X 10.9.4 (13E28)

Please find "System Information" in this folder path---Applications > Utilities---and launch it. When it opens, find "Power" in the left-hand contents pane and click it to get something like this in teh main pane:
Copy everything in the "Battery Information" and copy/paste it here. The number values in that report may help us diagnose what is happening.
Also, did you buy this battery directly from Apple or from another source. There are an increasing number of reports showing up that suggests some counterfeit batteries being sold.

HT5815 my macbook pro 15 inch 2.2 does not start up anymore after update, even after shift V.

Similar Messages

Maybe you are looking for