Http Instance always dropped

Hello
Anybody can help me to find out why the HTTP Instance always dropped by itself and have to restart manually once its dropped.
My messaging Server and Directory server sits in two different physical servers.
For for infomation:
Messaging Server
Sun One Messaging Server 5.2 (build Feb 21 2002)
Sun Solaris 8
Sun Fire 280R
Directory Server
Sun One DIrectory Server 5.1 SP1
Sun Solaris 8
Sun Fire 280R
Error Message
Server instance: /iplanet/servers/msg-messaging
Alarmid: serverresponse
Instance: http
Description: server response time in seconds
Current measured value (01/Jul/2003:09:38:05 +0800): 10
Lowest recorded value: 0
Highest recorded value: 10
Monitoring interval: 600 seconds
Alarm condition is when over threshold of 10
Number of times over threshold: 1
Thanks....

Tim Bao wrote:
I am running iPlanet Web Server 6.0 SP1 Evaluation version on my
W2k professional. But I found something strange and want to know why
NES always sends header in lower-case, ie., "Content-type" instead of
typical "Content-Type". I do know the header name is case-incensitive,
but it causes some dedicated HTTP client cannot recognize these
headers. Can I configure NES so that it will return "Content-Type"
instead of "Content-type"?You could conceivably modify this behaviour with your own NSAPI plugin, but
there is no configuration option that causes the sever to output
"Content-Type" instead of "Content-type".
A client that doesn't recognize "Content-type" and "Content-Type" as synonyms
is very badly broken.

Similar Messages

Why does my ipad2 always drop my wi if connection?

No matter what I do or how close I am to a wi if connection, it always drops. During surfing or downloading, I always have to reconnect. I bought this iPad 2 with the hope it was better than pc...but never had this issue with my net book.
What can I do, and what is apple dong to correct this issue?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Turn Off your iPad. Then turn Off the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
On your iPad go to Settings > General > Reset > Reset network settings and see if that enables you to connect.
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom

My s5 is always dropping calls, is there a setting I need to change or what could be wrong?

My s5 is always dropping calls, it doesn't matter if I am calling someone who has a cell phone or a landline. Is there a setting I need to change?

tbo27
Good Idea on the swap I was thinking of mentioning it after I posted silly me if doing the swap & the phone works better, then a Sim is definitely on Order.! And you can Order one through Customer Service Just make sure O.P. they send you the correct one you'll need the Nano Sim to fit in your s5
Customer Service's number 1-800-922-0204 or *611 when the automated gets to 3 and ask what you'd like to do say you want to talk to a Representative.. then tell them of the issue and you'd like to get a new Nano Sim.!

When I put my iphone5 on charge no matter where I am and even when I have full signal my phone will always drop the signal and continue to have no signal until I take it off charge. Is anyone else having this problem?

Everytime I put my iphone5 on charge now matter where I am and even when I have signal it always drops the signal and continues to have no signal until I take it off charge. I have the up to date software on it and everything and is relatively new. Is anyone else having this problem and how do I fix it?

This is a user to user support forum. We are all iphone users just like you.
You are not addressing Apple here at all.
This is an odd way to ask your fellow iphone users for help. Berating oterh users will not help you.
"it's too fragile"
No it is not. i have never damaged one, nor has anyone I know.
" U loose data when Ur phone is locked"
No you don't. Why do you think this?
"and there is no customer support!!! "
Wrong yet again. Apple has an 800 number and they have many retail stores and they have support articles that you can access using the search bar. Or you can contact them throgh express lane online
"but I will go back with Blackberry "
Please do.
Good ridance

When speaking to someone, my call is always dropped, whether I call my contact or she calls me. How to remedy this without expense?

When speaking to someone, my call is always dropped, whether I call my contact or she calls me. How do I remedy this without expense? I only receive one "dot" (or "bar") inside my home and even on the patio. Coverage is better in the driveway! I live in Florida my home is build like a bunker--poured concrete for protection against hurricanes. Well, it's protection against calls too. How can I fix this without spending lots of money?

VZW has a Network Extender that may work...I don't think it's too terribly expensive (depending on what you consider expensive)...but I've read on here where some people have had lots of luck with it...and others not so much. May be worth a try...give VZW a call and see what they can do for you.

Lync Monitoring Database, Named Instance, Always On

I have a SQL Server 2012 named instance (LYNC_MONITOR) on a specified port which is Always On enabled for deploying LYNC 2012 Monitoring and Reporting. I had moved the databases from another DB server into a Always On AG, which works fine, and set
up Listener on the defined port. My issue comes in when changing the topology. In the topology builder, the requested information is server name and instance (default or named). Well an AG Listener on a specified port is neither of those. If the instance was
actually default, then it would be no problem (but the default instance is SharePoint). So I need to be able to provide the Listener/port combo as the server name without specifying the instance. Currently it's just pointed to the primary node (server/instance).
Does anybody know of a way to get around this? Thanks much.
Tim Hacker

Currently SQL Always On is not supported for Lync 2013. That being said have you looked at setting up a SQL Alias (cliconfg.exe) on the Front Ends? I've used this when the SQL port is not the standard one: http://blogs.technet.com/b/nexthop/archive/2011/04/12/using-lync-server-2010-with-a-custom-sql-server-network-configuration.aspx
Please mark posts as answers/helpful if it answers your question.
Blog
Lync Validator - Used to assist in the validation and documentation of Lync Server 2013.

PS CS4 CSXSLibrary: "CSXSInterface.instance" always null

I was referred to this sub section of the adobe forums for this question:
I want:
Start creating my own Photoshop CS4 SWF panel coded with the FlexSDK in FlashDevelop (pure AS3, no flex).
I have:
FlexSDK & FlashDevelop
CSXSLibrary-2.0-sdk-3.4.swc
Photoshop CS4
issues:
whenever I try compile or test my compiled SWF movie in Photoshop I get a null object for the CSXSInterface.instance. This object however is supposed to be the bridge between AS3 and the Photoshop JSX interaction.
here is a simplified code that causes this error:
package
     import com.adobe.csxs.types.*;
     import com.adobe.csxs.events.*;
     import com.adobe.csxs.core.CSXSInterface;
     import flash.display.Sprite;
     import flash.events.Event;
     public class Main extends Sprite
          public function Main():void
               if (stage) init();
               else addEventListener(Event.ADDED_TO_STAGE, init);
          private function init(e:Event = null):void {
               CSXSInterface.instance.addEventListener(StateChangeEvent.WINDOW_OPEN, creationComplete);
          private function creationComplete(e:Event):void {
Once I compile the SWF and have it run in the debug Flash Player I get a error message:
[Fault] exception, information=TypeError: Error #1009: Cannot access a property or method of a null object reference.
And whenever I test the SWF as a Photoshop panel (by copying the SWF file in the plugin../panel folder) I get null objects whenever I try to access it which blocks any associated actions (events, triggers,...).
I am using CSXSLibrary-2.0-sdk-3.4.swc in combination with Photoshop CS4. Is that library perhaps not suited for CS4? Do I need a older library and if so where can I download it. Most of the libraries seem to be rather difficult to find on the internet anyway - which is a big drag for me.
The SWC library itself however is just fine added to the library as I can even access the CSXSInterface class itself booth while coding and at runtime. Just the .instance or getInstance() singleton returns always NULL.
Any insight or input would be greatly appriciated

I'm having the exact same problem, attempting to make a panel in Flash CS4 to run in Photoshop CS4.
I've tried CSXSLibrary-2.0-sdk-3.4.swc and CSXSLibrary-2.0-sdk-3.3.swc in the SDK, and the separate CSXSLibrary.swc that's been linked to. None of them work; CSXSInterface.instance is always null when my ActionScript runs in Photoshop.
All I'm doing right now is creating a single Button component, with a script that attempts to run a test function in Photoshop.
What's interesting is I can put the ShortcutButtons.jsx and ShortcutButtons.swf from the SDK into Plug-ins/Panels and that works just fine. My JavaScript is essentially the same:
function TestFn()
     alert("Hello, world!");
     app.documents.add();
And my ActionScript is as follows:
import com.adobe.csxs.core.CSXSInterface;
var btnTest = (root as MovieClip).btnTest;
btnTest.addEventListener("click", testFn);
function testFn(event:MouseEvent)
     CSXSInterface.instance.evalScript("TestFn");
(I've put other test code in the testFn() that confirms that the click event is registered correctly.)
I link the CSXSLibrary.swc in the "Library path" section of the ActionScript 3.0 settings, and I know it's being linked to because the size of my SWF balloons from 20 kB to anywhere from 50 to 300 kB depending on which library I'm trying.
What am I missing here...?
Thanks,
Dan.

Oracle instance always in 'shutdown' phase one day after installation

I have Windows 2003 Server (SP1) and Oracle database 10g release 2 installed.
On the installation day, after completing the installation everything worked just fine.
One day after that and on, everytime I boot up my OS the Oracle database instance is always in the 'shutdown' phase (though the listener is up).
So I have to manually start the database in 'open' mode.
The Enterprise Manager Console tells me that "TNS:Listener does not know the SID in the connect descriptor." This is strange, because I didn't change anything in the listener.ora and tnsnames.ora files after installation.
Could someone help me handle this problem?
Is this inherent in Oracle database 10g release 2?
P.S.: I have been using release 1 for some time and this never happened even months after installation.
Many thanks,
(Mario Andretti)

Please verify that you can get the database open manually.
If you can, then I suspect the problem is with the Enterprise Manager configuration. I believe the Enterprise Manager 10gR2 uses a different port by default than 10gR1. Depending on how you did the upgrade, you may need to look at the old port (or the new port) instead of the one you are using.
Further, if the database runs OK, and the problem is isolated to Enteprise Manager, you might be able to resolve the problem using emca (EM Config Assistant). In which case, I'd check the docs for further info, as I'm definitely a novice at emca.

Failover Cluster Instance always on

we have two node cluster active passive with shared storage , I have setup AlwaysOn as DR on standalone instance
daily morning on failover cluster events, i am getting following critical events
On windows log i couldn't see much information, please help me

Can you provide the version of Windows Server that you are using as cluster nodes? Behavior will be different between Windows Server 2008, 2012 and 2012 R2. While in the past, changing the NodeWeight property of a cluster node may be an appropriate solution,
Windows Server 2012 R2 introduced dynamic witness where a witness is configured to either have a vote or not have a vote depending on the state of the cluster and the quorum. Combined with dynamic quorum (which was introduced in Windows Server 2012,) which
dynamically adds or removes a vote from a node depending on the status, the behavior will be different depending on what version of Windows Server you are running. A more appropriate approach (if you are running Windows Server 2012 or 2012 R2) is to configure
the LowerQuorumPriorityNodeID property of the cluster.
http://technet.microsoft.com/en-ca/library/dn265972.aspx
Edwin Sarmiento SQL Server MVP | Microsoft Certified Master
Blog |
Twitter | LinkedIn
SQL Server High Availability and Disaster Recover Deep Dive Course

Specific WiFi access point HTTP proxy always turning off?

Hello,
My corporate - issued iPhone 4S which is currently sporting 6.1.1 has a weird issue - the corporate WiFi access point HTTP proxy setting always defaults to Off after trying to set it up with a Auto setting and entering a URL to our company's PAC file. My colleagues do not have the same issue - they are able to setup HTTP Proxy to Auto and enter the URL to the PAC file. I tried this with other access points (non-corporate) and it works fine. Is this something specific to the WiFi profile pushed to my device? I've tried contacting our company's IT personnel in charge and they weren't able to give me an answer. Hoping someone here can. Thanks in advance!
Cheers

To remove access poit, go to settings>connectivity>settings>Destination>Internet>long hold access point and select delete.
For Gmail, don't use it, but if you remove/delete mailbox and then set it up again it should work fine, also heard that during set up if you reject terms and conditions and set up manually it works better ?
http://asimag.wordpress.com/2007/06/22/how-to-configure-gmail-account-on-your-n95n73/
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Internet, but not local, service always drops at same time each day. HELP!

Hi there,
At first this was laughable but now it's becoming a real pain. For the past three weeks, sometime between 4 and 6 AM my router or modem drops the internet connection, but leaves the local only service in place. After a simple reboot with the router everything is back to normal. I am wondering what could be causing this? It's always at the same time. This doesn't happen at all during the day. The router does not indicate a problem with anything, since it can still generate local service, just not internet.
We did recently upgrade to the high speed internet up to 7000 instead of 2000. It's been happening since then. We're using a Westell 2200 modem (have had for years, it seems) and an Apple Airport Extreme for a router.
Any ideas would be appreciated. I am not sure how to get the numbers that were spoken of. I do have a phone plugged into another jack, but that's it. Have the inside wire maintenence plan if need be.
Thank you!
---Sarita

I had the same arrangement and Verizon sent a new 6100 modem/router for the higher speed service. The old modem did quite well but could not maintain the higher speed sync. I was advised by Verizon, when I upgraded to the higher turbo speed, that a new modem would be needed. I received one for no charge. I was surprised that the old unit performed as well as it did considering it was not designed for the higher speed. I suggest you call Verizon and request a new unit. I am in MA also.

IPhone 6 - Wifi always dropping, nightmare to reconnect

I wasn't allowed to post in any iPhone community for some bizarre reason..but I'm having serious trouble with my iPhone 6 and wifi.
The connection drops constantly and then it takes around 15 minutes of continuously clicking to get it to reconnect. This has happened since the moment I took it out of the box, and it took me over an hour before I was even able to progress through the initial setup (there was no skip wifi setup the first time round!).
I get the 'unable to connect' and 'incorrect password' messages over and over, despite the password being correct (as it always eventually does connect). If I leave my phone unattended for a second then it will disconnect, and it will never connect automatically when I get home. To get it working, I literally have to toggle airplane mode around 100 times and continuously click our wifi until finally it decides to connect. When connected though, the wifi works great. But it disconnects so often (every time I pick up my phone) and it takes so, so long to reconnect that it's basically unusable.
- Handset has been changed, so it's not a hardware issue with the phone.
- Software all up to date, on the phone and the router.
- Router is standard from TalkTalk (Huawei HG523a), but it works so great and fast for every other device (iPhone 5s, Macbook Pro) and hasn't ever lost connection with those, so I'm assuming the hardware is also fine with that.
- Tried all the usual things on the phone - 'reset network settings', restoring (as new and NOT from iCloud backup), etc.
- Made sure all my internet settings match these: iOS and OS X: Recommended settings for Wi-Fi routers and access points - Apple Support.
It seemed to connect fine to the wifi in the Apple store when I got the phone changed for a new one, to which I was advised my problem might be specific to password protected wifi's....? Any help would be appreciated. I'm not buying a new router just so my iPhone 6 connects better - iPhone 4 and 5 connect fine, so why doesn't the 6?

So, how would your question relate to the products that we support in this forum pictured below? The iOS experts do not hang out here.
If you cannot post in the iPhone support forum, try a post in the iPad support forum, since iOS is the same on both the iPhone and iPad
Using iPad

Oracle 10g http issue. always ask for XDB and APEX password

As i m uses oracle 10g express edition, it ask for XDB and Apex password frequently.
i changed the port from 8080 to 8181 but still same problem.
Any solution?

If you wish to enable anonymous access to the ML DB repository, the following code creates the "<allow-repository-anonymous-access>" element if it is missing, or updates it if it is already present in the xdbconfig.xml file.
CONN sys/password AS SYSDBA
SET SERVEROUTPUT ON
DECLARE
l_configxml XMLTYPE;
l_value VARCHAR2(5) := 'true'; -- (true/false)
BEGIN
l_configxml := DBMS_XDB.cfg_get();
IF l_configxml.existsNode('/xdbconfig/sysconfig/protocolconfig/httpconfig/allow-repository-anonymous-access') = 0 THEN
-- Add missing element.
SELECT insertChildXML
l_configxml,
     '/xdbconfig/sysconfig/protocolconfig/httpconfig',
     'allow-repository-anonymous-access',
     XMLType('<allow-repository-anonymous-access xmlns="http://xmlns.oracle.com/xdb/xdbconfig.xsd">' ||
     l_value ||
     '</allow-repository-anonymous-access>'),
     'xmlns="http://xmlns.oracle.com/xdb/xdbconfig.xsd"'
INTO l_configxml
FROM dual;
DBMS_OUTPUT.put_line('Element inserted.');
ELSE
-- Update existing element.
SELECT updateXML
DBMS_XDB.cfg_get(),
'/xdbconfig/sysconfig/protocolconfig/httpconfig/allow-repository-anonymous-access/text()',
l_value,
'xmlns="http://xmlns.oracle.com/xdb/xdbconfig.xsd"'
INTO l_configxml
FROM dual;
DBMS_OUTPUT.put_line('Element updated.');
END IF;
DBMS_XDB.cfg_update(l_configxml);
DBMS_XDB.cfg_refresh;
END;
/

Swing Program Slow on Some Computers Second Instance Always Fast

I am having a unusual and frustrating problem. I have a java swing application compiled and run with 1.5.06.
On some computers the program runs very slowly and takes a long time to paint to the screen. If however, you run a second instance of the program the second instance runs very fast. If you close the first instance the second instance remains fast.
Running the java console first will also make my program fast.
On other PC's with the identical hardware it runs fine the first time. All the computers involved run windows 2000.
Please help with this weird problem. Thanks.

It seems that you need to fine tune ur JVM based you requirement.
Try setting the max heap size.
Also, You can tyr -XX jvm option. But the decision purely depends on you applications behaviour.
Thanks
Jobinesh

When I open fiefox, several instances always open at once. can't open just one.

whenever I click on Firefox icon or taskbar , several firefox windows now seem to open. At the moment, one click has resulted in 17 instances of firefox.

Don't what to say but WOW! downloaded and ran malwarebytes. It found a Trojan and something else. At the same time, my Trend Micro finally ran a scan and found 2 trojans and a cycbot, both associated with Adobe. Did the superantispyware program too, found a couple things. Uninstalled reinstalled firefox without any of the old personal settings, so NO add-ons at all. Opened in SAFE MODE and the error STILL persists. Computer does not want to shut-down and I find that I can do a few things then programs won't open anymore (such as my Trend Micro antivirus and even firefox.) I have no idea how any of this happened. I know a fair amount about computers and do NOT open links etc that I am not sure about. It was working fine while using in my truck yesterday. When I brought it in the house, it started doing all this. Just plain WEIRD! Any other ideas?

Http Instance always dropped

Similar Messages

Maybe you are looking for