Huey Pro not working after Windows 7 Ultimate install on W510

I just received my W510 and installed Windows 7 Ultimate x64 as well as all of the relevant W510 drivers. I've also installed Huey Pro. I've read many similar posts regarding the Huey Pro issue and followed all of them. Unfortunately Huey Pro isn't able to turn on the monitor when the lid is closed. I installed the Lenovo power driver and set the to do nothing with the lid closed. I set the same settings for Windows power management just in case. To make sure I have the right drivers I installed the Thinkpad System update.
How can I make Huey Pro work?

Make sure you have the Lenovo Thinkpad Communications Utlity installed.
mullion wrote:
I just received my W510 and installed Windows 7 Ultimate x64 as well as all of the relevant W510 drivers. I've also installed Huey Pro. I've read many similar posts regarding the Huey Pro issue and followed all of them. Unfortunately Huey Pro isn't able to turn on the monitor when the lid is closed. I installed the Lenovo power driver and set the to do nothing with the lid closed. I set the same settings for Windows power management just in case. To make sure I have the right drivers I installed the Thinkpad System update.
How can I make Huey Pro work?

Similar Messages

  • Satellite Pro U400-15I - Sound Wheel not working after Windows 7 install

    The sound wheel on my Satellite Pro U400-15l does nothing after the Windows 7 clean install from XP pro.
    I used the recommended Software update tool downloaded from Toshiba. The VolumeIndicator.exe process is running and the sound works OK - just not under the control of the wheel! Also the Toshiba Power control is not there but this is not a problem.
    Any suggestions welcome.
    Bob Sheppard

    Hi Syntax,
    there is no option to add the volume control to the taskbar in the control panel.
    The sound driver is 'Conexant High Definition Smart Audio 221'
    Interestingly, when I click on the speaker icon on the taskbar and select the mixer option I get 3 sliders called 'Device','Applications' and 'Sound Volume Indicator of Toshiba Control'. If I move this slider with my mouse I get the indicator I am looking for ( The Toshiba indicator I had under XP). However, this slider only works as a 'minimum' for the other sliders.
    Thanks for your help but I still would like that volume indicator back!
    Bob Sheppard

  • Communication to internet not working after Windows 10 installed

    I just upgraded to windows 10 and after installing everything worked fine, then I did a couple of updates today for Windows 10 and then I could not connect to internet either via wifi or hardwire.  My connection to the internet would start but then drop off withing a minute.   any suggestions?

    It could also be problems associated with the service pack reinstalled when you reinstalled - you may need to get service pack two on a disk to bring it up to speed.   It may also be that your windows reinstall does not supply the drivers for your NIC, which probably was supplied by the PC manufacturer, or, if your NIC was ever upgraded or replaced, its drivers would not be in your windows reinstall.
    cjacobs001

  • Brightness Control not working after Windows 8 install...

    Hi All,
    I have a late year 2010 MBA core2duo with 4GB of ram, and I was running Windows 7 for a long time and recently bought a Windows 8 upgrade key. I heard the boot camp drivers were updated so I decided to load it up. I installed the new boot camp drivers on the Windows 7 side before the upgrade (had to use the command line to do the driver upgrade).
    Windows 8 is all installed and the only issue I have is the brightness control doesnt work at all. I disabled the adaptive brightness as a lot of threads have been saying. Anybody have any ideas what I need to do to fix this?? It seems to be stuck on BRIGHT.

    I have been having the issue of no brighness control when running windows through bootcamp for about 6 months now and have not found any applicable solution online.
    While messing around trying to figure it out yet again I noticed that my monitor driver was signed by team viewer...
    Sure enough clicking the roll driver back button resolved the issue by rolling the driver back to the Microsoft driver...
    So long story short:
    Right click "My Computer" click properties
    Click device manager (lop left of window)
    Expand Monitors section
    Double Click monitor
    Click driver tab
    If the driver here is not signed by Microsot or Apple click the roll back button. My driver version is 6.1.7600.16385 (Driver date 6/21/2006)
    Rolling this back instantly resolved my issue. I will now propagate this post to all the threads I saw regarding this issue.
    I am running windows 7 x64 Ulti on a 15" rMBP.
    Best of luck

  • Re: Graphics card not working after Windows 10 install

    Hi, i still have my original SCM installed, like from the original 8.1 install.
    Is there a new version released for Windows 10 maybe? I don't know what could be causing this.

    Hi there,
    I am using MSI motherboard 970A-G45 and windows 7 BIOS is at 1.11
    However if i upgrade to Windows 10 does that mean i have to upgrade to (Windows 8) BIOS 2.7 or wait until they release the BIOS driver for Windows 10.
    They managed to update mo...

  • Beats Audio Control Panel software not working after Windows 10 upgrade.

    Beats Audio Control Panel software not working after Windows 10 upgrade.  the Beats sound enhancement is useless in WIndows 10. When opening the Windows 10 sound properties  I'm getting this box message: Auido enhancement problem Windows has detected the audio enhancement for the following device are causing problems: Speakers / Headphones (IDT High Definition Audio Codec) Woud you like to disable driver enhancement for this device?  IDT High Definition Audio CodecBeats Audio Control Panel version6.10.6491.02013.11.2009:43:18 Please provide some kind of fix for this?

    Well, it has been a long road on the Win 10 upgrade. At first I got the same error message as above, but after deleting the Dolby Advanced Audio v2 in Win 10 using Control Panel Programs and Features and rebooting, I got into the continual BSOD upon reboot. Here are the steps I took to at least get stable on Windows 10. First, I rolled back to Windows 8.1 using the advanced feature in the BSOD recovery options. Once back in Win 8.1, I deleted the Dolby Advanced Audio v2 using Add/Remove Programs in Control Panel. Then I downloaded the Win 10 update and re-installed it. Once that completed, I updated the Intel Graphics driver under the display adapters (on my G780 it is an Intel HD Graphics 4000, and the driver can be found at  https://downloadcenter.intel.com/). Currently I am running version 10.18.10.4252 for my machine. Then, under the Device Manager, I updated the Conexant SmartAudio HD driver under the Sound, video, and game controllers. That driver is currently at 8.66.4.50 and was automatically downloaded from the web when I requested to update driver.  I also changed several others settings such as Notify to schedule restart after updates are installed instead of automatic (under Settings --> Update & Security --> Advanced Options) and Do you want Windows to download driver software and realistic icons for your devices? --> No, let me choose what to do, never install driver software from Windows Update.  After that, I shut down the machine, waited a moment and booted back up. I have no idea why this helped or if it is overkill, but I am stable and running without a fear of rebooting now. Hope this helps if someone else is having this same issue.

  • My laser jet 100 color MFP M175nw is not working after windows 8.1 upgrade,

    my laser jet 100 color MFP M175nw is not working after windows 8.1 upgrade, driver on your website fails to setup at 83 % with an error message

    Welcome to the HP Forums  MillaMagia,
    I see by your post that the USB isn't being recognized.
    I can help you with this issue.
    Are you using the same USB cable? (known good USB cable)
    You want to use the normal USB slot 2.0 cable and not the latest USB 3.0.
    USB 3.0 are supposed to be backwards compatible.
    Try another USB port on the Laptop, some of the USB ports are more powered then others.
    I have provided a document to see if the printer is partially recognized in the device manager, which is causing the printer not to be recognized again. (the uninstall from the CD should have removed the entry and the printer from the registry)
    Leave the printer turned on and the USB cable connected directly to the computer and the printer's power cord directly into a wall outlet.
    How do I get into Windows Device Manager?
    Here is a document for Identifying problems in Windows Device Manager.
    Check to see if there are any hardware driver conflicts, you might see a ! mark or a red x beside a device with a conflict or unknown device, look under universal serial bus controllers, look for USB printing support or mass storage device, delete the entry by right clicking and select uninstall, OK.
    Let me know how it was listed. (screen shots welcome)
    If this is a Laptop then check the power management settings.
    Access the device manager. Windows 8-How do I access the Device Manager.
    Select universal serial bus controllers from the list, for each USB root hub, right click and left click on properties, for power management remove the check mark for "Allow the computer to turn off this device to save power". It allows the computer to limit or turn off power for this device.
    Disconnect the USB, run the full uninstall and reinstall the printer software again.
    If you need further assistance, let me know.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • HP Photosmart C6300 printer/scanner not working after Snow Leopard install

    HP Photosmart C6300 printer/scanner not working after Snow Leopard install
    Reinstalling etc does not work - does anyone else have the same problem or a clue as to how to fix this?

    Keith,
    I got a C6280 and the scanner does not work anymore. I am for 6 days in contact with HP. The last printer driver install form the apple web site does not open the image of HewlettPackardPrinterDrivers.dmg because of an invalid checksum. The skipping of the validation gives and error in the install.

  • HT3917 My apple wireless keyboard is not working after new batteries installed

    My apple wireless keyboard is not working after new batteries installed.

    Do you get a steady green light to say there is a connection.    If not, are the batteries the right way round.   Do you have a monitor to tell the batteries strength. Is there a reading.   Are the batteries good quality ones, Duracell, Energiser or Apple rechargeables.

  • Fingerprint Reader not working after windows password reset

    Hi There
    I was using windows login (single admin user) and fingerprint reader to login to my Thinkpad T510. Yesterday night I changed windows password and I didn't update finger print. Unfortunately I am not able to login when I tried to login using windows login today, I forgot the password and when I tried finger print reader it is just throwing error.
    Why finger print is not working after windows password reset? What should I do to login?
    Help would be appreciated!!

    I just called the tech support just now? I just asked the 'why the finger print reader not recognizing the finger print after changing windows password?', and he gave the following answers
    1. You should change fingerprint while changing windows password.  I don't understand the reason behind it, btw is this true?
    2. We can't do anything for this issue.

  • Touch screen not working after windows 10

    Touch screen is not working after windows 10 was down loaded.  Also the zoom keeps changing on it's own.  Does anyone know how to fix this?

    Could you provide the unit's Model name/number?

  • Compaq Presario CQ62 DVD not working after Windows 7 automatic install of upgrades

    The DVD in my Compaq CQ62 stopped working after Windows 7 automatically installed updates. The driver seems to be corrupted. When I open Device Manager, the DVD comes up as hp DVD RW AD-7701H SATA CdRom Device and the device status displays...A driver (service) for this device has been disabled.  An alternate driver may be providing this functionality. (Code 32).. There are two drivers installed--cdrom.sys from Microsoft,  File Version 6.1.7600.16385(win7_rtm.090713-1255) and PxHlpa64.sys File Version 2.03.32a from Sonic Solutions. If anyone knows the link to download the new driver or how to resolve this problem please let me know.

    We are not sure what might have caused this issue. You may try removing the affected filter drivers and check. This has helped few.
    To do this, follow these steps:
    1. Click Start , type regedit in the Start Search box, and then click regedit in the Programs list.
    If you are prompted for an administrator password or confirmation, type your password, or click Continue.
    2. Locate, and then click the following registry subkey:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
    Caution There can be many instances of the registry subkey that is mentioned in step 2. You must make sure that you are in the appropriate registry subkey before modifying the UpperFilters and the LowerFilters values. To verify that you are in the appropriate registry subkey, make sure that the Default data value is DVD/CD-ROM and the Class data value is CDROM.
    3. In the right pane, right-click UpperFilters, and then click Delete.
    4. Click Yes to confirm the removal of the UpperFilters registry entry.
    5. In the right pane, right-click LowerFilters, and then click Delete.
    6. Click Yes to confirm the removal of the LowerFilters registry entry.
    7. Exit Registry Editor, and then restart the computer.
    Note After you remove the UpperFilters registry entry and the LowerFilters registry entry, you may lose functionality in certain programs such as CD recording programs. In this scenario, you must reinstall any affected programs.
    See which Windows updates are installed
    http://windows.microsoft.com/en-US/windows7/See-which-Windows-updates-are-installed

  • Touchsmart 320-1030 Touchscreen is not working after OS re-install

    HDD crashed, and was replaced with new, re-installed system from factory recovery CDs, now touch screen does not work. I have re-installed the drivers to no avail. system Properties says under Pen and Touch:  No Pen or Touch Input is available for this Display. It used to work before the hard drive crashed. Is there a setting in the BIOS? or something else I may have missed?
    Thanks

    Hello @ncmich2,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how the Touchscreen of your desktop computer is not working after replacing the Hard Drive, and I would be happy to assist you in this matter!
    To re-enable the touchscreen features on your computer, I recommend re-installing the original software and hardware drivers that first came with your computer. This can be done by following the steps in this document on Using Recovery Manager to Restore Software and Drivers (Windows 7). To update the newly installed software, please follow this resource on Using HP Support Assistant (Windows 7).
    Please re-post with the results of your troubleshooting, and I look forward to your reply!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Z580 Dolby digital plus not working after Windows 10 upgrade

    Dolby Digital Plus is not working after I installed Windows 10 upgrade, I've tried several things to fix the problem with no luck, has anyone else experienced the same problem and found a fix ???

    Hi,I have tried by switching dolby on but its not showing any difference. The app is installed but not working you can do on/off, set equlaizer but it doesnot show any effect. Recently i have upgraded to windows10.I used to love the Dolby experience but now its not working and its really disappointment for music lovers & gamers. Please provide any help on this issue. ThanksGopal

  • Acrobat X Pro not working, tryed to re-install and does not recognize Serial Number?

    Acrobat X Pro not working, Serial Number not recognized?

    Hi lv123321,
    Do you have Acrobat only License no or is it a part of suite. If Acrobat X pro is a part of suite then you need to use the suite setup to install Acrobat.
    Also if possible could you please private message me the serial no so I can try decoding it.
    Regards,
    Abhijit

Maybe you are looking for