Hunt group question

We have a customer who is currently set-up in the following manner: All external calls ring a receptionist. If she is busy or not available, the call hunts to another user and so on. There are currently five (5) users set-up like this. These users all have a button on their existing phones labeled Available. When this button is inactive (not pushed), they are in the incoming calls hunt group. When this button is active (pushed), the user is no longer available to receive calls from this hunt group. They can still make and receive calls to their internal extensions.
Short of installing IPCC, how can I mimic this functionality?
Its easy enough to set-up a hunt group, but I dont know of a way to take the extensions out of availability for the hunt group when the users dont want to take these calls but still want to receive internal calls made to their extensions.
Thanks in advance for your assistance!
Chris

Chris,
You can accomplish this with Attendant Console. The users would have a piece of software on their PC that controls their availability. Please see the following link for details.
http://www.cisco.com/en/US/products/sw/voicesw/ps555/index.html
http://www.cisco.com/en/US/products/sw/voicesw/ps555/products_installation_and_configuration_guide09186a0080176f6e.html
Hope this helps. If so, please rate the post.
Brandon

Similar Messages

Hunt Group Shared Line question

Customer has the following call routing scenario:
CCM 4.2(3)
CTI Route Point is CFwdAll to a Hunt Pilot.
Hunt Pilot contains Hunt List containing a broadcast Hunt Group of 5 phones.
4 of these 5 phones each have the other phones' shared line appearances (ring disabled) so they can see if they are on the phone.
Issue - When incoming call hits the CTI RP, it then goes to the Hunt Pilot, Hunt List, then it "should" ring all the phones in the hunt group. But it only rings the very first DN in the Hunt Group and the DN of the phone that is not setup as a shared line on the other phones. The 4 phones that have each other's DNs setup as shared lines only see the call info popup on the LCD screen showing that the first DN is receiving the call, but their phone doesn't ring.
As a test, I switched the order of the hunt group DNs. After the switch, I realized that only the first number in the broadcast hunt group will ring. Kind of defeats the purpose of a broadcast hunt group. :(
I am starting to see where the issue may come from. If a phone has shared lines setup for DNs that are in a broadcast hunt group, each time a call comes in, then the phones would fill up the LCD with the call info for the 4 shared line DNs.
Any suggestions on allowing phones to be in a broadcast hunt group, and having shared line appearances to monitor the status of the other phones in the hunt group?
Thanks,
Kevin

Hi Kevin,
You are right on the money! Here is an odd tech note that applies to CCM 4.1.X , 4.2.X and 5.0.x. The reason I say odd is that it is hard to read or make sense of, but it is saying exactly what you have discovered.
Note: Do not put DNs that are shared lines in a line group that uses the Broadcast distribution algorithm. Cisco CallManager cannot display all DNs that are shared lines on devices where the DNs are configured as shared lines if the DNs are members of a line group that uses the Broadcast distribution algorithm.
From this doc;
Cisco CallManager Administration Guide, Release 4.1(3) Line Group Configuration
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00803ed665.html#wp1036009
In the current environment I can't think of a good way to accomplish your goal of being able to monitor each others activity while using Broadcast hunting.
I know this doesn't help, but at least you know why it works the way it does. (and have some documentation)
Take care!
Rob

Setting up Hunt Group using an extension number instead of a pilot number

Hi Guys,
I would like to set up a hunt group. My question is can I use a real extension number assigned to a phone to be a pilot number instead of creating a new pilot number.
The requirements are if no one is answering a call to an extension 1000 (extension 1000 is assigned to a user) it should be forwarded to 1001, 1002, 1003 and back to 1000. I was thinking of using 1000 as pilot number. Is that possible ?
Thanks Guys

Hi Guys,
Thank you very much for your suggestions. Here is what I have done:
With Manish's solution the call forwarding works upto the third phone then it got disengaged. Looks like there is a timer I need to increase so that the call will not time out. Could you please let me know which timer I have to adjust. I have checked the max forwards hops and they are set to 15-20 so don't think this is an issue.
With regard to Jamie's solution, I have created a separate partition and assigned same DN 1000 to it. It works great when I call from inside. However when I call it from outside using the full E164 number the call goes to 1000 then it just go to the voicemail of 1000 if not answered. I have removed the settings under DN page so that it will not go to voicemail. After doing this the phone with extension 1000 keeps ringing until it times out. Not sure where the issue is here.
I have given a suggestion to my customer to use a new pilot number with hunt groups. I have tested this as well. When I call it from outside the call goes to all the five phones and it just keep going into circle until someone answered and that's what I want. But when I call DN 1000 from inside it goes to all the five phones and when I reaches to the last phone configured under the line group member the call then just dropped out. Is there a way to fix this so that when someone just dial the extension number from inside all the phones keep ringing in circle manner and did not drop until someone has answered it.
Thanks a lot guys.
Regards

Lync RSG Hunt Group not working as expected, not getting calls on lync clients

I have created an Hunt Group in Lync. When i dial the number i do get the welcome message but after that it does not get forwarded to the test user which is configured in the Group. (Created a Queue and selected the group here and assigned this to the workflow)
Error on Lync report:
Request: BYE Response: 200
Diagnostic ID: 26029 Category: Unexpected
Component: Response Group application
Reason:
Call is disconnected because of invalid configuration.
Description:
Call is disconnected because of invalid configuration.
Error in Event Viewer:
The workflow runtime encountered a critical error.
Failure occurrences: 8, since 4/17/2012 7:47:14 AM.
The last encountered error was from a workflow with the display name: TestRG, the URI: sip:[email protected], and the GUID: 810c628c-d0c5-4b31-b8d5-f61595def5b0
Suhas

HI,
Do you deploy standard lync server or enterprise lync server?
If enterprise lync server, please log in SQL server and search the rgsdyn--dbo.ActiveFEInstance. Please check you can find the FE server FQDN and the port 8404 in this table.
Please running the Lync server logging tool on the FE server to find why the Response Group can not transfer the calls to the agent.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

UM Hunt Groups

We have one Lync Enterprise pool and several branch sites with SBA's.
We have two Exchange 2010 pools, one for users in the West Coast, and one for users in the East Coast. Each Exchange pools has CAS, Hub Transport, Mailbox, and UM servers.
Should there be a UM Hunt Group to link every gateway (ie Lync FE & SBA) to every UM server, or do I need to be more restrictive, such that only those Lync servers on the West Coast link to those UM servers on the West Coast, etc?

Hi,
Understood your question let me try to answer this.
If you have two sites Site A and Site B. In site A you have Lync Server 2010 FE and another site you have SBA's. so assuming you have two have two Central Datacenters for Exchange correct?
Site A is having different extension with a dial plan ans site B has different extensions with different dial plans correct?
"Dial plans ensure that all extensions are unique within the architecture by mapping a dial plan to a PBX. Extensions within a dial plan must be unique. However, extensions between different
dial plans do not have to be unique. A user can only belong to a single dial plan and will have an extension number that uniquely identifies him within the dial plan"
I also believe that these two Datacenters are not failover of each other?
If yes then take a look in to this http://technet.microsoft.com/en-us/library/gg398656.aspx
ISolation of gateways and UM servers
if you are going to isolate gateways and UM servers assuming you have single UM server in both sites and you are going to isolate it then there will not be any failover with in the site and one server goes down you will not have any redundancy how ever you
can isolate it. If you have two um servers i believe go with the isolation create different dial plans for respective gateways.
Without Isolation of gateways and UM servers
If you are not going to isolate you will have redundancy between sites which gives you high avialability. might be the best option to go but network bandwidth and network latency should be taken care.
I suggest to have a look in to this which will give you more help
http://technet.microsoft.com/en-us/library/bb123925.aspx
http://technet.microsoft.com/en-us/library/bb125141.aspx
http://technet.microsoft.com/en-us/library/gg399031.aspx
Hope above make sens.
If answer is helpful, please hit the green arrow on the left, or mark as answer. Salahuddin | Blogs:http://salahuddinkhatri.wordpress.com | MCITP Microsoft Lync

Hunt Groups and Voicemail

Was not sure if this was the right group to post these questions. I believe that these will be super easy for this group, and I want to double check my thinking against you guys. So, here they are.
If we elect to use a BROADCAST type of hunt group in some of our departments (all phones in the hunt group ring simultaneously when a call is directed to the group) and then direct that call to a DEPARTMENTAL VOICE MAIL BOX in a BNA condition:
1. Can the call ring with a unique ring that those in the hunt group can identify as different from a call that is directed specifically to their personal extension?
2. If the call to the hunt group ends up in the departmental HUNT GROUP VOICE MAIL BOX, will all phones in the hunt group receive notification that a message exists in the GROUP voice mail box?
3. If yes to 2 above, when any one individual in the group dials in to the group box and listens to the message, are all message waiting indicators subsequently turned off and does the person who responded to the message then become the owner of the message in his personal mail box?
Additional questions not related to hunt groups:
4. Do internal station to station calls ring with a special tone that differentiates them from external inbound calls?

Brian,
1. There is not a distintive ring option in CM. You could create a 2nd line on your user's phones and add those lines to the hunt. From there the user can select a different ring for the line (this is a local phone option for ring).
2. Setup alternate MWI on the group vmail box. Alternate I believe has a limit of 9. If you have more users than that then create a DN on each of their phones with the same # of the voicemail box. If that number is the original vmail pilot that is a CTI or other device then you wont be able to do that but you could create another DN and use a translation and the Multiple Tenant MWI option in CM service. Reply back if you need more detail.
3. MWI is turned off. The message stays in the group mailbox, there is no forwarding unless the user manually forwards it.
4. Not by default and I don't believe you have that option but not totally sure.
Please rate any helpful posts
Thanks
Fred

Hunt Group with Pots lines in Call Manager

Hello all. I have a site with 12 Pots lines. It is all configured via Call Manager. We are using mgcp. I asked the telco to setup the numbers to hunt which they said they did but still when I call the main number second time it just rings and eventually get some voicemail that is not from the call manager. I think I need to setup Hunting in the Call Manager? Is that correct?
Line Group --> Add the extensions in here and set them up to hunt?
Hunt List --> Create a Hunt list and associate a Line Group with it?
Hunt Pilot --> I add all the extensions in here?

Let's take one step back. What are you trying to accomplish? I am assuming you want to market one number but have the ability to accept multiple calls on that number. If that is the case, having the telco set up a hunt is the way to go.
Beyond that, where do you want those calls from the PSTN to route? Are you wanting those calls to ring a hunt group on your side? If so, you will need to do the following:
     1. Configure a Line group. (Call Routing -> Route/Hunt -> Line Group) This is where you will be adding the extensions. You will also need to specify a distribution algorithm. The distribution algorith, is where you will be choosing how you want the extensions to ring. For instance, if you set the DA to broadcast, every extension in the line group will ring at the same time. Click Help --> this page, while you are in the line group configuration page to get more information about the settings you can modify and different algorithms you can use.
     2. Configure a Hunt List. (Call Routing -> Route/Hunt -> Hunt List) You will need to create a new Hunt List and add your line group to it. The hunt list is evaluated in a top down fashion. You can get pretty tricky with multiple line groups with different distribution algorithms in your hunt list, but if you just want something basic,just add the line group you made.
     3. Configure the Hunt Pilot. (Call Routing -> Route/Hunt -> Hunt Pilot) The hunt pilot will be the dialed number that triggers the hunt group. Make sure you select all the required settings. You will be selecting the hunt list you just made in this configuration page. Be sure to set a maximum hunt timer and final destination so that the calls do not just ring forever. You can get pretty granular with the settings in here. Reference the help --> this page document for more information.
     4. POINT THE FXO PORTS TO THE HUNT PILOT. This is very important. Calls to your analog lines will not trigger the hunt group unless you point the ports to the Hunt Pilot. If you are using MGCP/SCCP you will need to enter the hunt pilot in the "Attendant DN" field for EVERY FXO port. If you do not enter a value here, CUCM will have no idea what to do when the port rings. It will not answer the call if there is no value specified. This would explain why your calls were ending up with the telco voicemail service; CUCM was never answering the call.
If you completed the above steps correctly, you should be able to call the main number multiple times and have the calls go to a hunt group on your side, no matter which line the call ends up coming in on.
Let me know if you have any questions, this can be kind of tricky at first.
PS, if the calls were going to a voicemail that wasn't from Call Manager (Unity Connection) call the telco and have them remove voicemail service from the lines, assuming you have configured Unity Connection to handle that.
Hope this helps,
Dallan

Hunt Group Queues

We are evaluating moving from an Avaya 8710 based enterprise PBX to a Cisco PBX. A sticking point we have come accross is how to do basic phone features supported by the Avaya system. A major one is the ability to queue calls in a hunt group. We have sites that have up to 3 or 4 hunt groups and if a call comes in and all members in the hunt group are not available then the call goes to Music on hold until the call can be picked up by the next available in the hunt group.
Is this really a limitation in Call Manager 5.x, 6.x or CME 4.3?

To answer your question about IPCC express, I know it used to be free with CallManager 4.x, not sure with 5.x and came with 5 licenses. But with IPCCx, you can do just about anything you want when it comes to queing, onhold, music, transfers, etc.
But from looking at the doc I sent you:
Understanding Call Queuing
You can configure a pilot point to support call queuing, so when a call comes to pilot point and all hunt groups members are busy, Cisco CallManager Attendant Console sends calls to a queue. While in the queue, the callers receive music on hold if you have chosen an audio source from the Network Hold Audio Source and the User Hold MOH Audio Source drop-down list boxes in the Device Pool window or the Pilot Point Configuration window. The attendants cannot view the queued calls. When a hunt group member becomes available, Cisco CallManager Attendant Console redirects the call to that hunt group member.
You enable queuing for a pilot point by checking the Queuing Enabled check box on the Pilot Point Configuration window. You must also enter a value in the Queue Size field and the Hold Time (in Seconds) field. The queue size specifies the number of calls that are allowed in the queue. If the queue is full, Cisco CallManager Attendant Console routes calls to the "always route" hunt group member that is specified on the Hunt Group Configuration window. If you do not specify an always route member, Cisco CallManager Attendant Console drops the call when the queue size limit is reached. The hold time specifies the maximum time (in seconds) that Cisco CallManager Attendant Console keeps a call in the queue. If the call is in the queue for longer than the "HoldTime," the call gets redirected to "AlwaysRoute" member. If the "AlwaysRoute" member is not configured, no action occurs.
This is saying that the CCM Attendant Console will take care of what you need. It's basically a big queing machine. You dont have to have a live person answer to start the que from what it looks like, just point the calls to the pilot number and let the server take control of the ques.
You can do this one ccm cluster, or hub and spoke in your case. Just remember, that if you are queing calls, you are tying up WAN bandwidth the more you que. But it may work out ok, depending on how much bandwidth you have.
You can get MOH streams off your local router at the remote site, so you are not streaming MOH over the WAN, so that should take care of itself.
Unity can act as a poor man's que. Basically you can have ccm hunt the groups, no one answer, go to Unity voicemail, play a message, transfer back to the hunt group, hunt the group, then possibly back to Unity to play a message, then take a message. (just using a different mailbox and a different pilot number)
Sometimes you have to get creative with these products to make them do what you want them to do. Out of the box, it's not always the exact feature you need, but you have to tweak it.
Most companies that use hunt groups, understand that they are basica in CCM until you port it to IPCC Express. Unity does do menu trees very well, multilevel voicemail, multiply extesnsions to one account, etc.
My best advice for you, get together with your local Cisco SE to go over the features you require and see how it can be done.
cheers!

Hunt group and 2911-CME SRST

Imagine this is (1) main hub with a Cisco CUBE 2900, 2 remote sites with Cisco 2911 CME-SRST. All connected via MPLS.
Goal:
If MPLS link or MPLS CE in remote site1 fails, I want to have *inbound* calls forwarded to the POTS line in the branch1.
VoIP Service provider does offer a feature which allow me to select target DIDs and have inbound calls forwarded to whichever number I specify.
Question:
Let's say there 20 people in the branch office1.
Can I setup a hunt group using Cisco 2911 CME and that single number which received the call start ringing the phone of all staff until we find someone to take call? Does CME and support hunt groups and this scenario?

Yes, CME supports various types of hunt groups.
However to have more than one phone ring at once, the best is to use a shared DN.

CCX using Place Call to hunt group. Unable to determine who answered

I'm trying to use the CCX to place a call to a CUCM hunt group and then once the answered, determine which member of the hunt group answered the call.
I have used several of the Get Info steps, including:
Get Call Contact Info
Get Enterprise Call Info
Get Contact Info
However, all of those steps always just report back the CUCM hunt pilot number, instead of the actual line group member who answered the call. Can anyone think of a way to determine the extension of the line group member that answered the call ?
If it matters, I am using CCX 9.0.2su1

I lack a system to test this on at the moment but perhaps try this CUCM Service Parameter. The question is whether CTI Manager will follow this logic or if this is only respected by the CDR flat file export.
Show Line Group Member DN in finalCalledPartyNumber CDR Field
This parameter determines whether the the finalCalledPartyNumber field in call detail records (CDR) shows the directory number (DN) of the line group member who answered the call or the hunt pilot DN. Valid values specify True (the finalCalledPartyNumber in CDRs will show the DN of the phone that answered the call) or False (the finalCalledPartyNumber in CDRs will show the hunt pilot DN). This parameter applies only to basic calls routed through a hunt list without feature interaction such as transfer, conference, call park, and so on. If a feature is involved in the call, then the hunt pilot DN will show in the finalCalledPartyNumber field regardless of the setting in this parameter. This parameter does not apply to Cisco CallManager Attendant Console.
This is a required field.
Default: False

Hunt Group and Voice Mail - How?

Hello,
We are setting up a Hunt Group (Line Group, Hunt List, Hunt Pilot) for call distribution. We don?t want to use the Attendant console for this, we just want the calls distributed. We need to send some calls and broadcast them to different phones. We have it working but we have a need that if no one answers to send the call to voicemail.
The way we have it configured right now?
Line Group:
Broadcast Distribution
2 Lines ? Client Phone Lines
Hunt List:
Line Group Above
Hunt Pilot:
Number & Information Configured
Hunt List Above
What we planned on doing was to take and add a second line group with a single number that is forwarded to voicemail. Then in the hunt list, if no one answers the fist group, go to the second. The problem is, CTI Ports and CTI Route Points don?t seem to be able to be added to the Line Group.
Someone suggested that I add a ?fake? phone and forward the line to voicemail. I tried that and when I call that number it goes to voicemail but when I add it to the Line Group it rings fast busy when it rolls to it.
Any ideas?

I did understand you do not want the attendant console, which is why I said similar but using AC.
The key thing in my earlier reply is that the last member of my hunt group is another CTI routepoint with another DN which is the actual directory number I use in Unity as an alternate extension, but it might be that this does not work for you.
For your case it might be something like:
On the xisting CTI routepoint configure the forward no answer to VM (this works today, correct?)
Then add another CTI route point to your hunt list and configure that CTI route point with forward all to VM.
Then setup Unity with the DN for the first CTI route point and add the DN of the second CTI route point as an alternate extension.
That way I believe it will go to VM directly when no huntgroup members are available, and go to VM if no answer.
Again, this works for me, with the only difference my line group contains AC users and is not broadcast, but the principle would be the same I guess.
But I might be misunderstanding what you are trying to achieve. If so, I am sorry for misunderstanding ;-)
Thanks,
Leo

Voice mail as last stop for hunt group

Hello:
We have no ACD ability, so I have a hunt group set up with 3 extensions (one each as second line on each of 3 phones). If no one is available on any of the hunt extensions, I want it to go to a shared voice mail box.
Can anyone help me know if this is do-able and how (nothing I've tried has worked!). Using CM 6.1/Unity 5.0
Thank you,
Linda

Hi Linda,
This is most possible :) I'm going to add a touch to the great info from Tere (+5 points for this Tere)
In this example we are going to do what you are trying to do as well as Light the MWI Lamp on the phones within the Line Group when a Message is left for the group.
Lets say the Hunt Pilot number is 5000 and one of the second line DN's on the Line Group member phones is 2355. Set the Hunt Pilot to Forward (CFNA) to the Unity Pilot #.
If you don't use a Routing Rule as nicely suggested by Tere you can Create a mailbox for 2355 with 5000 as an Alternate Extension. When the call routes through to Unity via the Hunt Pilot No Answer Unity should see the CLID of 5000 which will then be connected to the Mailbox on 2355. This will take care of one of the Line Group Member phones but we want to light the Lamp on the second and third phone as well :)
Try setting the the DN's of the other two Line Group members as Alternate MWI's (in Unity) as well;
Setting Up Alternate MWIs for Extensions on the Same Phone System
Cisco Unity can activate alternate MWIs for extensions on the same phone system. Note that depending on the phones and phone systems, some additional phone system programming may be necessary. Refer to the installation guide for the phone system.
To enable alternate MWIs for extensions on the same phone system, do the following procedure for each subscriber who needs alternate MWIs.
To Set Up Alternate MWIs for Extensions on the Same Phone System
Step 1 In the Cisco Unity Administrator, go to the applicable Subscribers > Subscribers > Messages page.
Step 2 Confirm that the Use MWI for Message Notification check box is checked.
Step 3 Click the Add button located beneath the MWI Extensions table to add a row to the table. By default, the first row in the table contains an "X" to indicate the primary extension assigned to a subscriber. If you want one more extension and do not need to activate the MWI on the primary extension, you can also modify the first row.
Step 4 Enter the applicable extension in the Extension field of the table. MWIs are automatically enabled for all rows in the table. When entering characters in the MWI Extensions table, consider the following:
â¢Enter digits 0 through 9. Do not use spaces, dashes, or parentheses.
â¢Enter , (comma) to insert a one-second pause.
â¢Enter # and * to correspond to the # and * keys on the phone.
Step 5 Click the Save icon.
Step 6 Repeat Step 3 through Step 5 as necessary.
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/401/integration/guide/c50acu4x.html#wp1808513
Then tweak the Message Lamp Setting in CCM for the second Line appearances;
For the second Line Setting on (each phone)-
Line Settings for this Device - Changes affect only this device
Message Waiting Lamp Policy - Light and Prompt
The RED Message Lamp will then work for these Second lines on each phone.
Hope this helps!
Rob

CUCM 8.6 - Call Forward All Doesn't Work With DN In Hunt Group

Hello,
I'm trying to make a hunt group that's sole purpose is to dial out to our Help Desk member's cell phone (on-call after hours). The idea is that we want the hunt group to broadcast the call to the on-call engineers. Whoever picks up first takes the call.
At least that's the idea now. They may want to change that to - ring primary on-call cell phone, if no answer ring secondary on-call engineer.
The target cell phones will change every week and I wanted to give the supervisor a means of changing the numbers through the ccmuser page.
I created two DNs and placed them in a hunt group, each with call forward all to a cell phone number.
It seems that the hunt group ignores the call forward all setting and that is by design (https://supportforums.cisco.com/document/9126/cisco-callmanager-call-forward-all-cfa-does-not-work-if-line-hunt-group).
Does anyone else have any suggestions on how to accomplish this?

That's correct, what you're seeing is WAD, this topic has been discussed plenty of times before, the only option you have is SNR

CCME Call Forward from one Hunt Group to another Hunt Group Failure

Hi I have a couple of hungroups in Cisco Call Manager Express. I am trying to configure a Call Forward no answer from one hunt group to another. Does anybody know if this is possible? If so, is there a config available? Here is my config, but it is not working.
Thanks,
Derek
voice hunt-group 20 parallel
final 2290
list 2201,2251,2252
timeout 30
pilot 2209

Hi Derek,
This is supported with the restriction shown below;
final number
Router(config-voice-hunt-group)# final 8888
Defines the last extension in a voice hunt group.
If a final number in one hunt group is configured as a pilot number of another hunt group, the pilot number of the first hunt group cannot be configured as a final number in any other hunt group.
From;
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmecover.html#72373
Cheers!
Rob

CVP 7.0(2) SIP RNA Timer with CUCM Hunt Group

I have a very simple ICM 7.5(9) script which simply assigns a call type then forwards to a label on CUCM 7.1(5), which is a hunt pilot containing a hunt list with 2 line groups...a circular LG with 10 members (RNA reversion timeout of 20 sec), followed by a broadcast LG with different 10 members. There is no CFNA/CFB forwarding set up on the hunt pilot.
In CVP, the SIP RNA timer is set on for this DN at 120 seconds, and I can see that get set in CVP logs (IP addresses and dialed numbers modified to protect customer data):
41762417: 10.100.1.41: Dec 03 2012 20:23:28.977 -0500: %CVP_7_0_SIP-7-CALL: {Thrd=Pool:SIP[7059609]} Matched 666333315555551111 to proxy.customer.uc
41762418: 10.100.1.41: Dec 03 2012 20:23:28.977 -0500: %CVP_7_0_SIP-7-CALL: {Thrd=Pool:SIP[7059609]} Using Local Static Route for sip:[email protected]
41762419: 10.100.1.41: Dec 03 2012 20:23:28.977 -0500: %CVP_7_0_SIP-7-CALL: {Thrd=Pool:SIP[7059609]} Matched 666333315555551111 to TimeoutMatcher: patterns like 66633331> will use RONA of 120
41762420: 10.100.1.41: Dec 03 2012 20:23:28.977 -0500: %CVP_7_0_SIP-7-CALL: {Thrd=Pool:SIP[7059609]} CALLGUID = 0B19E39A3CE811E28B7DA21700DE4950 LEGID = 0B19E39A3CE811E28B7DA21700DE4950-135458420897716680 - [OUTBOUND]: INVITE TO <sip:[email protected];transport=udp> FROM "--CVP" <sip:[email protected]:5060> EXPIRES[120] 100REL[Unsupported]
The hunt group then begins hunting, and can be answered normally. However, a CANCEL is sent at 60 seconds, and I am not sure why:
From the gateway:
2106715: Dec 3 20:24:29.095: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
CANCEL sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.100.1.5:5060;branch=z9hG4bK2C171513C0
From: "--CVP" <sip:[email protected]>;tag=20687DD0-DAF
To: <sip:[email protected]>
Date: Tue, 04 Dec 2012 01:23:29 GMT
Call-ID:
[email protected]
CSeq: 101 CANCEL
Max-Forwards: 70
Timestamp: 1354584269
Reason: Q.850;cause=19
Content-Length: 0
From CUCM SDI traces:
12/03/2012 20:24:29.169 CCM|//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message from 10.100.3.30 on port 43568 index 566129 with 389 bytes:
CANCEL sip:[email protected]:5060;transport=tcp SIP/2.0
Via: SIP/2.0/TCP 10.100.3.30:5060;branch=z9hG4bK51cac6f4-76fb29a5-78d5dd99-9a021233-1
Call-ID: [email protected]
From: "--CVP" <sip:[email protected]:5060>;tag=ds229f1b0f
To: <sip:[email protected];transport=udp>
CSeq: 1 CANCEL
Content-Length: 0
I am trying to determine which timer is limiting the hunt to 60 seconds.
Can anyone suggest where I might begin looking?
Thanks so much!!!

I've run into a similar problem recently with a CVP 8.5(1) SIP deployment and have found in the CVP documentation that the RNA Timeout is a range configurable between 5 and 60 seconds.
You can enter a larger value through OAMP on the Call Server-->SIP-->Advanced Configuration tab but when you Save and Deploy, it reverts back to the max of 60 seconds. The CVP help file indicates the 5-60 second range.
Regards,
Matt

Hunt group question

Similar Messages

Maybe you are looking for