Husbands and my iPhone 4 home button faulty at same time.
My husband I noticed that the home button was unusable at the same time and then started working again at the same time. We both had a good signal and were in the same room. Today the same thing happened didn't work then did around the same time..
I checked with my daughter and her home button has been having problems during the times we have had them too. Does anybody think this is all just coincidental?
Similar Messages
-
my iphone 4 stopped working suddenly....it wouldnt charge or anything...i was told to push the on button and the home button at the same time and it came back on.
is this a fault with the iphone????
i cant have my phone switching off randomly...any help please...thankyou.sometimes it happens, a hard reset will sometimes solve the issue.
If the issue starts happening more often, I would consider restoring the device to factory settings to install clean software. If the issue still persists after that, the device might need a hardware repair.
More info on backing up and restoring the software: http://support.apple.com/kb/HT4137
Good luck
Stijn -
I have a brand new Ipod touch with front facing camera. Not sure which generation it is. My wife connected the iPod Touch and chose the restore option when connecting to iTunes. It was a mistake and by the time I got there, I saw the screen with USB cable with an arrow facing towards iTunes logo. I cannot get the iPod out of this state.
Try here:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows
Also reset the iPod.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears. -
One day I was going to download music from my laptop to my ipod, I was able to download all the songs I wanted but later when I try to charger my ipod it wouldn't let me. The next day I bought a new charger but it still didn't charger. I try pressing the power And home button at the same time but it still wouldn't turn on or charger.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
plz hlp
- See if resetting the iPod will make it visible in iTunes so yu can restore the iPod.
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Next see if placing the iPod in recovery mode will allow iTunes to see the iPod so you can restore the iPod. For recovery mode see:
iPhone and iPod touch: Unable to update or restore
- Last, see if DFU mode will allow a restore.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
When my Ipod touch is in autolock I can only restart the device holding the sleep/wake button and home button at the same time for 10 seconds. While in auto-lock it is using battery power and will do so until the battery is drained. Whats wrong?
- Try a reset. Nothing is lost:
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears
- Connect the iPod to your computer and try to restore via iTunes. Try placing in Recovery mode if necessary to restore.
- If you can't turn the iPod completely off, let the batter fully drain. After charging for at lerast anhour try again
- If still not successful time for an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. -
is there another way i could turn my phone on? it wont turn on or show me the battery screen to show its charging. i already tried to hold the on and home button at the same time but it does not want to turn on. please help?
Device Not Recognised
For PC
http://support.apple.com/kb/TS1538
For Mac
http://support.apple.com/kb/ts1591 -
hello i hav an ipad mini and i was in the middle of the ios 8 update and i held the sleep and home button at the same time to cancel the update and now it wants me to connect to itunes i dont no how to do that can someone pleaze help me?
RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary. -
I recently reset my iPod touch 4th gen. (holding power and home buttons at the same time.) now it won't let me change my wallpaper, in the photo section or the settings. Any ideas, please? Thanks.
What happens when you try to change them?
Try:
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device. -
I am having trouble with my iPad, i can start it, but the iPad does not work. i tried to use the power and home button at the same time, the apple logo appears, but the iPad does not work. What am I suppose to do?
After the Apple logo appears, what happens then? Can you hear any sounds or if you tap on the screen, does it seem like apps can open or are you just seeing a black screen? You might have a hardware problem, but you can try restoring the software and see what happens.
Read this in its entirety before you do anything. Make sure you read the sections at the end about using recovery mode.
iTunes: Restoring iOS software - Support - Apple -
My sons iPod touch stopped working, it won't charge in a docking station and the computer/itunes won't recognize it when connected. We have tried holding the power and home button at the same time for several seconds, and the screen still stays black. Thanks!
Hello skdog I possibly think your ipod touch is black because it has not charged. If your dock is broken it might just mean the dock will be broken and so might be the USB port. You should see an Apple shop nearby and hand it over and see what they can do. I hope this information works!
-
my ipad will not let me slide to log in, or power off. I have tried to hold down the sleep and home button at the same time, but that did not work. D o you have any tips for me? Thanks.
recovery mode
open itunes on computer
plug cable into computer not iOS device
turn phone off
hold home button and plug cable into phone. do not release home button until an itunes graphic appears on device.
look to computer should have message about recovery mode click ok and restore
Peace, Clyde
if u need an article see
http://support.apple.com/kb/HT1808 -
Ipad2 won't shut down even when i press the sleep/wake button and the home button at the same time.
I can't shut down my ipad2 even when i press and hold the sleep/wake button and the home button at the same time.
If the screen appears to be zoomed in, then does tapping the screen with three fingers zoom you back out ? When zoom is on you should also be able to scroll around the screen using three fingers on the screen.
If you are seeing the keypad then that should be for the iPad's passcode, I assume that you have one set ? If the iPad is disabled then I wouldn't expect the keypad to show. -
my ipad is on an infinite loop. I used ios7 for a few days and then did updates on some of my apps. that's when the infinite loop started. I have tried pressing the power and home button at the same time, but it doesn't work. Please help!
I even tried some hints posted for ios6 (turn off Ipad, holding home button and plugging in power cord at the same time and then releasing the home button)
I did manage to get a different screen that shows the itunes icon and a power cord, but nothing happens.You were on the right track. You got the connect to iTunes screen and you ended to use iTujes to restore your iPad. Try recovery mode again.
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad. -
Hi there guys i got an ipod touch 4 generation last yr it turns on and shows the apple but then freezes ive even tried to click the home button and on button on the same time but it restarts and freezes at the apple any suggens to fix it guys please thanks heaps guys
Try #2 and #3 in link below. If neither work, you most likely have a hardware issue.
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro 8G RAM 750G HD + OCZ Vertex 3 SSD Boot HD
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
In Memory of Steve Jobs
Maybe you are looking for
-
SharePoint 2013 with sp1 install on windows server 2012 R2
Hi All: excuse me I have a question about sharepoint installation. I install sharepoint 2013 with sp1 on windows server 2012 R2,but i always got "Configuring Application Server Role, Web Server (IIS) Role" message. I refer to this article <http://sup
-
How to produce a word document to show on a smartboard at school
I want to produce a word document with mac for microsoft windows 2011 , i need to know how to make a one page document and then make it into 2 pages to view on a smartboard at school for large type and easy viewing. I used to just go into view and th
-
Hi. I have got problem with my smartform. When i look at smartform from spool or from print preview it looks ok, but when i try to make pdf file using OTF table my smartform is without special characters (polish letters). Any advice ?
-
BI 4.1 installation in Red hat Linux 6.5
Hi Experts, we are planning to have one cluster environment in Red hat Linux 6.5. 1) Two nodes in cluster ( two red hat Linux 6.5 servers) 2) 1 server with Websphere as a web application server. From the last two years i am completely working on wind
-
Maintain pricing conditions for the material for the excise invoice date
When I am doing MIGO (Release GR Blocked Stock-movement type) t)he system is giving an error "Maintain pricing conditions for the material for the excise invoice date"I am attaching screen shot for reference. I request if any one can provide me the s