HV20 and Print to Video or Edit to Tape?

Has anyone figured out the workflow for final cut pro and getting video back out to tape using
"print to video"
or
"edit to tape"
with "edit to tape" I get an "unable to initialize" error where it tells me to check the audio/video settings.
with "print to video"
I'm using the record/pause function from page 71 of the manual, but the hv20 doesn't see to see a signal. Also the playback on the mac is interesting. it's in the middle of the screen, and not showing the full resolution..
basically I'm just trying to dub an hdv tape.
thanks!
-Josh

ok, the only things listed in the audio/video settings are the ntsc and pal firewire devices.
when I try to set it to hdv 1080i60 firewire basic, I get the error:
unable to locate the following external devices:
HDV (1440 x 1080) 60i
but the camera is both connected... and on. Is there a reason it would see the camera as an SD device instead of a HD device?

Similar Messages

Print to video vs. edit to tape

what is the preferred format? i've been using print to video
but i hear edit to tape is a lot better.
did a search but not much came up.
any comments?

Print to video just outputs the timeline to tape...to possibility of timecode lock. It preps the cut then prompts you to press record.
Edit to Tape gives deck control. And it allows for locking the deck to output to your timelines timecode...with the show starting at hour 1;00;00;00.
Shane

Print to video or edit to tape?

i just finished my project on fcp4.5hd and i was to put it back onto a mini dv tape so i can send it away, do i edit to tape or print to video? and can you please explain how to do it? thanks for your help

Don't double post. Only confuses the issue.
http://discussions.apple.com/thread.jspa?threadID=1728346&tstart=0

Print to video vs edit to tape - which to use?

I'm new to FCP. I want to output to a tape that has not been entirely blacked or striped. Should I use Edit to Tape assemble edit? Or will Print to Video work?
thanks!

Thanks. I just read the user manual PDF and think that is the way I am going to go. I want to start at 01:00:00;00 and be frame accurate.
thank you!!

Edited on MacPro, needs to Write Video to Edit-to-Tape on PowerMac G5?

Anyone else run into this issue?
I edit programs for broadcast on my MacPro at home (same version & settings as Final Cut software on systems at the office). Everything right up through rendering is done on my home system.
I bring it in via G-raid(firewire800) to one of the office systems with decks for printing, both of which are PowerMac G5s.
Open project - timelines look/play rendered as they did when I finished them at home.
Edit to Tape - after I drag/drop the sequence to Insert in the Edit-to-Tape window, Final Cut then proceeds to "write video" for at least 45 minutes as if it's re-rendering the entire sequence.
Through a TON of elimination & troubleshooting, we discovered this error is consistent when our other MacPro in the office gets the same result when an edited/rendered sequence from it is brought over to the G5s.
What are your thoughts?

I have often found that the rendering FCP needs to do just before an Edit to Tape to be very inconstient. I wonder if it could be writing the render to a different drive on the MacPro other that the G-Raid. I also wonder if it might be rendering to RAM for output.... I've never heard of this so it's just a theory. Do you do a Sequence > Render Only > Mixdown? Might try that. Also do a forum search for "Edit to Tape" as there are many topics on the subject.
And welcome to the forum.

Print to Video "beep" also on tape

Hi,
I'm using final cut express and I have captured some movies without any problem to my harddisk. Now I made a compilation and want it to print to video (using the menu option "Print to Video". When I do that, my camcorder records the sound and the image. That's oke. The problem is that a continous beep is also being recorded. My ToneLevel is -60dB.
Questions: How can I "Print to Video" without that annoying beep ?
I'm using FCE4, on OSX10.5 and a MacBook, 2Gb, capturing on a DV camera.
Thanks,
Rokesh

The Command+R worked on the Sequence.
I tried to "print to video" an imported DV file (so no sequence, but directly).
Thanks for all the help. I finally got it working.
First I created a sequence, than dragged the movie on it, then Command +R, then print to video.

Print to Video Error msg: audio and vide devices may not match

When I attempt to print to video (using a Sony DV deck that has werved me well for years) I receive the message:
"The selected audio and video devices may not match:
-Apple FireWire NTSC (720 X 480)
Please verify that the audio and video outputs are externally routed to the intended device(s).
Do you want to proceed?"
I tried proceeding, and the video images output to the tape but without a sound track.
What to do? I must deliver a tape to my client!
I recently did a software update to 10.4.6. Could that be part of the problem?
Of did some setting change somewhere without my knowing it, and I need to reset it, if so what?
Thanks in advance

Hello!
Thank you for this. I did check the audio playback settings and it was NOT set to audio follows video. I then CHANGED it as you have kindly instructed. The audio video settings box you mention was NOT checked, so I didn't need to do anything there.
I then tried o launch Print to Video (not Edit to Tape) and sadly, the same error message occurred. Any suggestions would be much appreciated.
I am running FCP 4.5, recently upgraded to OS 10.4.6
Thanks in advance.
Hey Pamela,
Have you been monitoring externally this whole time?
If you have, and you've been getting external audio
and video, then this is probably a case of a
setting being off somewhere.
First, check your View > Audio Playback
setting. It should be set to Audio follows
Video.
Second, press Option-Command-Q to bring up the
Audio/Video Settings dialog. Click on the right-most
tab (A/V Devices) then confirm that the box for 'Use
Different output for Edit To Tape/Print To Video' is
not checked.
And please confirm that you're doing a Print to Video
and not an Edit To Tape. I ask because the only time
that I can remember getting this message is when I've
tried to do an Edit To Tape and didn't drag the
correct sequence from the browser (if I remember
correctly, I accidently dragged a sequence that was
also open in timeline).

Help with timecode and video freeze during Print to Video

This has happened twice in last couple months. Timeline is usually around 22 - 23 minutes. At some point during playback to HDV deck using Print to Video via FireWire, the timecode freezes and so does the video for approx. 2-3 seconds, then resumes on 2-3 seconds later in the timeline. Everything is still in perfect sync. Playing back the timeline on computer reveals nothing. Please, does anyone have any suggestions at all??

You should be mixing down the audio before you record to tape, try that if you haven't done it first...
If that fails, export a self contained QuickTime movie, then see if it doesn't print to video or edit to tape better.
Use the fastest drive you have for the QT movie's playback, and it should be something other than your startup disk.
Jerry

Print to Video Does not Work

I am running Final Cut pro 5. I am trying to send my time line to a mindv deck using print to video. I have a monitor hooked up to the deck to watch what is being recorded. I set my in and out points in the time line and and select print to video from the menu. I do not have any of the boxes checked, because i have black and color bars already in my time line. I select in/out and hit ok. The screen goes black and my video shows up in the middle playing, but nothing shows up on my monitor and when i watch the tape that i am recording to, there is nothing on there as well. The device control is working, because I can capture footage off of the deck, but it seems to not be getting a signal when I am trying to print to tape. I have also tried edit to tape, and I press record on the deck after setting up the sequence and then I play the sequence, and nothing is still recorded onto the tape. For both edit to tape and print to tape, everything is working, but nothing is being recorded onto the tape. I have also tried hooking up my sony camera to be used to record, but that doesn't work either. Any help would be great thanks!
G5 Mac OS X (10.3.9)

Make sure the deck has it's input selection set to firewire for starters...
I'm not clear if this is part of the problem, but FCP 5.0.4 will run better in Tiger.
But if you can see external video, you should also be able to print to video or edit to tape... if you can't then keep troubleshooting your Firewire connection... got a different cable to try? Can you capture video OK?
Jerry

Printing to video error

I am using the latest version of Final Cut Pro. Whenever I finish a video, I print it back to a DV so I have an original. It continues to play on the computer and I do not see any errors when it plays on the computer. However, sometimes on the DV, the audio cuts out and sometimes both audio and video cuts out, but then comes back. Sometimes both audio and video come backa and sometimes only video.

I am using the latest version of Final Cut Pro. Whenever I finish a video, I print it back to a DV so I have an original. It continues to play on the computer and I do not see any errors when it plays on the computer. However, sometimes on the DV, the audio cuts out and sometimes both audio and video cuts out, but then comes back. Sometimes both audio and video come backa and sometimes only video.
Rebecca, would you mind elaborating on your hardware setup? You list your machine as a G4 - does that mean PowerMac, PowerBook, iMac, eMac, iBook?
Where does your media reside? (internal drive? external drive?) Please speak on how large - and how full - your media drive(s) is/are as well. What else - if anything - is on your FireWire bus? (how many hard drives? any other devices [like an iSight or an iPod]?)
Also, how are you getting back to tape? Print To Video? Edit To Tape? Or are you simply outputting from Timeline?
Are the two dropped frame warning in your User Preferences - 'Report dropped frames during playback' and 'Abort ETT/PTV on dropped frames' - checked? (If not, try a Print To Video with the warnings enabled.)
While I think this is some type of hardware issue - since you're not getting errors from within FCP - but if it is an FCP issue, speak on the contents of this sequence - any nested sequences, or large still images, or 44.1khz audio files that could cause drop outs like that?

Help urgently needed with edit to tape / print to video error

I have tried to edit to tape and print to video a sequence (0my whole project, worked for way too many nights to let go... so frustrated and sad right now because it doesn't work.
The project is saved on an extern harddisk, my harddrive on teh pc is too full (not big enough).
My camera and FCP connects but all the time I get an error that 'the tape may be locked' . AND I HAVE TRIED WITH DIFFERENT TAPES, none of them were locked!
I am not really sure how to set the camera in this VTR mode... I have tried in the settings to set it in webcam mode... and I have tried without... and I dont have a button or setting called VTR, only a *PLAY' option or a 'FILMØ option....
My A/V settings are FireWire PAL and DA PAL 48khz ... however have no ide what that means or if these should be changed...?
I checked from apple but cannot find my DV cam on the list... hmm, does that mean I cannot do edit to tape recordings???
My Dv cams informations:
NV-GS140 by Panasonic, Model 0x80330B, 0x804580114B5DD1
I checked the system settings and was able to the FireWire/NV-GS140 Unit
I have a MacBook1,1 / Intel Core Duo/ 2 GHz
OS 10.4.11
I use the version FCP 2
Please help me out, I am really without any good suggestions how to proceed!

You're going to have to use a dvd authoring program. Burning the seq to a dvd qill just create a qt movie on a dvd data disc. It won't create a dvd video disc that plays in a dvd player.
Export from fcp a QT movie, current settings, self-contained. Use Anamorphicizer (http://mac.softpedia.com/get/Video/Anamorphicizer.shtml) to make imovie recognise it as 16:9. Then import that file to idvd.
Or you can drop your 16:9 sequence into a new 4:3 sequence to letterbox it, then you can do the export as above but skip the anamorphicizer step.
It's better to use compressor on the original 16:9 sequence and then use dvdsp to author, but if you've never used dvdsp it's a big program to get your head round.
The export can be done in two ways;
1. Export from fcp using 'export using compressor'.
2. Export a QT ref/self-contained movie and import that into compressor.
3. Export a QT movie and import it direct into DVDSP.
The second option will take longer initially (if you use the self-contained option) but will then allow compressor to work in the background, the first option will tie up fcp for the duration of the encode.
Once in compressor use one of the 16:9 dvd presets, depending on the duration of the movie and the quality you want. Don't try to adjust the settings. If your movie is 31 mins just use the shortest option (i think it's 60min) and make sure you select the m2v video and ac3 audio options. If you just select the mpeg 2 video you'll only get video, as you've discovered.
Open dvdsp and create your opening menu and a video track, import the movie file, add it to the video track, and then add the audio to the track as well. Then add any chapter submenus you may want.

Print to Video - freeze and lost sound

Hi,
I'm using a Mac Pro and FCE HD 3.5 with a La Cie 250 GB external drive attached through FW 800. The whole thing is attached to a Sony DSR 11 deck.
Everytime I try to print my (six minute) project to video, it runs for about 4 minutes and then freezes at exactly the same point. Then after a couple of seconds, it starts up again but with no sound. At the same time, I hear the La Cie drive whirring and then seeming to power down (but I'm not sure). I have done a disk repair on the La Cie and it's verified etc.
I checked the shot where the freeze occurs and it seems OK - it's about 300 MB large, no movement, no transitions or color correction or sound filters etc applied - just a straightforward shot. The file does not seem to be corrupted (but is there any way of telling?)
When I play the project in the timeline it runs fine. I have done all the necessary "render sequence" and "audio" renders, even each time before print to video (even though it does not seem to need rendering).
I also exported the projected to Quick Time and used the QT to try and print to video but with the same result.
The strange thing is that another sequence in the same project that is 8 minutes long, prints to video perfectly.
I am totally mystified by this and wonder if anyone can help me.
Thanks!

Before you go off & spend money, are you absolutely sure you have actually rendered everything & mixed down your audio?
Sequence > Render All > Both
Sequence > Render Only > Mixdown Audio
Also, for what it's worth, I have encountered enough problems with Print to Video that I have taken to just playing from the timeline when I want to record on an external device, and not bothering with PrintToVideo.

HDV Print to Video not showing metadata

I'm running Final Cut Studio 2 and a Canon HV20 camcorder. I'm trying to consolidate footage from one tape to a new tape using "Print to Video" but the metadata such as date and time doesn't transfer. It works perfectly when I tested with DV format (consolidating 1 DV to another) but HDV only transfers video and audio with no metadata, and I'm guessing timecode too but I'm not sure. The original tape shows metadata.
I'ved tried with different settings. Captured using HDV Firewire, HDV Firewire Basic, HDV Firewire Basic NDF, AIC and print to video using HDV (1440 x 1080) 60i. They all record to tape fine but no metadata. I've even tried capturing and export to tape using iMovie with the same results (only video and audio with no metadata/timecode). What am I doing wrong?

Nope, I'm not talking about photo EXIF metadata, I'm talking about actual video. If I play DV or HDV tapes on my camcorder the date and time of the recording displays in the lower right hand corner of the LCD screen and the time even changes based upon when it was recorded. I've owned 3 DV camcorders and used friend's and they all do this.
When recording DV or HDV the date and time is registered somewhere. Even the new iMovie '08 will name the clips you import by date and time shot for DV or HDV (ex. clip-2003-02-09 13;57;34.dv).
Again, I can import any DV tape (video) now, export it to another tape, play it and the date and time of when it was recorded is retained, even if I rearrange it's order in iMovie or FCP. This is something I've done for years. I just can't accomplish it with HDV. I'm sure it can be done I just need to see what I'm doing wrong in the chain.
Please don't let my use of the word metadata confuse you that I think it's photo EXIF metadata. I used the word metadata because it just means "a set of data that describes and gives information about other data."
Thanks.

Print to Video error

I've created a project using both GL1 and XL1 video footage in FCP 3.
Everything has gone fine with the digitizing and editing, but when I try and Print to Video, it goes to a blue screen during the XL1 footage.
What gives?

Try making a self contained quicktime (if you have the hard drive space) and exporting that. Make it with 'use current settings'.
Does it work?
x

Print to Video quitting

I have done this a million times without a problem, but now...
When I hook up my HV20 deck and print to video(minidv), it works for awhile and then arbitrarily quits without any error message. My deck keeps recording, but the screen just goes back to my timeline.
I have tried it multiple times and it quits at different spots each time.
I have conformed my HDV project, so that it can shoot it out from the timeline like I always do.
I got a new firewire, but that isn't the problem.
The original file is on an external hard drive that is connected via firewire.
Any suggestions? I am at my wits end.

1) Are you printing "entire media" or "in to out" if it's the later make sure your "out" is in the right place.
2) try exporting your project as a self-contained movie, put it in a new timeline and then print to video

HV20 and Print to Video or Edit to Tape?

Similar Messages

Maybe you are looking for