HW recommendation and advice on optimal setup
I have two requierments:
Security
Failover/redundancy
Related information:
6 external links:
4 dsl from 4 different ISPs (2 mbps up/down)
two point to point microwave links (15 mbps up/down)
Public access services:
Webservice, should be set to failover between 4 DSL
X service, should be set to failover between two microwave links. (will consume 10 mbps up/down)
LAN related services:
AD
DNS
etc..
Initial thoughts:
SLA trackign for ISP to satisfy failovers
HW failover between two cisco appliances for hw failures.
three different DMZ :
webservice related servers
X service related servers
LAN related servers
No ideas what so ever when it comes to security (ips,ids,etc.. )
Any recommendation or advice would be appreciated.
Happy to help. I will be candid in that I have not used the RV016 yet. That said, please see page 75 (Multi-WAN) of the admin guide.
http://www.cisco.com/en/US/docs/routers/csbr/rv0xx/administration/guide/rv0xx_AG_78-19576.pdf
It states:
"IP Group (By Users): Select this option to group traffic on each WAN
interface by priority levels or classes of service (CoS). With this feature, you
can ensure bandwidth and higher priority for the specified services and
users. All traffic that is not added to the IP Group uses Intelligent Balancer
mode. To specify the services and users, click the Edit icon for the WAN
interface and then add protocol binding entries for each service, IP address,
or range of IP addresses."
This would lead me to believe that you can accomplish what you are wanting to by using CoS and IP Group.
As for the ISA question. I'm a long time user of the ASA, and the PIX before it. The ISA is not a replacement to the ASA in any fashion. It's directed at a different target audience. That said, I've been very impressed with how functional it is. There are some things it can't do (like NONAT). However for the most part it's very similar to the ASA in how it uses Address/Service Objects/Groups, NAT/PAT, Static NAT, Access Rules, etc. It's doesn't have a CLI. It doesn't have an Active/Standby option however it does support VRRP. To answer your last question, it doesn't have a modular capability to support expantion. As I said at the beginning, I've very impressed with it though. You can take a look at the emulator if you want. It's located here:
http://www.cisco.com/assets/sol/sb/isa500_emulator/index.htm
Shawn Eftink
CCNA/CCDA
Please rate all helpful posts and mark correct answers to assist others searching for solutions in the community.
Similar Messages
-
Hardware recommendations and advice for 100 client network
Hi
We are currently looking at setting up a very basic separate wireless network for a client in two adjacent large cabins (3m apart) that will support up to 100 clients max concurrently. This will be solely for contractors to access basic internet, connections to web mail etc. There will be no existing infrastructure to connect to, so we will be looking at an internet connection of some form, a small switch and the wireless network. Range isn't an issue as they are next to each other its the support for such a large amount of connections. I thought a clustered setup of 2-4 WAP321 might be a bit stretched and we might get issues as the number of simultaneous connections gets near 100. I was also looking at a couple of standalone Aironet 1600s, one in each cabin.
The network itself is very basic, as it is literally just shared internet access but I need to ensure that it's reliable with 100 clients connected.
I did ring presales tech but they weren't mcuh help and sounded like they knew less than me, so any help would be appreciated.
Regards
HarryDear Harry,
Thank you for reaching Small Business Support Community.
By checking on the WAP321 datasheet I see:
- Recommended user support = Up to 32 connective users, 20 active users
- Active clients per cluster = 80
I agree with you when say "might be a bit stretched and we might get issues as the number of simultaneous connections gets near 100", therefore I suggest you to go for an enterprise-class, entry-level device like the Aironet1600 you mention. I would anyway suggest you to contact back the presales team or the Wireless-Mobility Support Community for further assistance and advice.
Thank you for your time on this matter and please let me know if there is anything I may assist you with in the meantime.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found. -
Audigy platinum ex questions and advice - dual ouput or dual card - motherboard audio op has died
Hi all.
im new to the forums and would like some advice please.
i use my pc for mixing music and DJ'ing, but the problem that i have is that the onboard sound output has died. i need 2 intendant / separate sound outputs, one for preview, and one for main/live output.
Now, is it possible to configure a audigy platinum ex to provide the required outputs, and if so, how.
if this is not possible, can i use a soundblaster live card in the same pc to provide the required outputs, or as i suspect the answer is no to this due to shared file names within the drivers and such, is there a recommended card that i can use in conjunction with the audigy, or will any generic sound card do the job (for preview output).
i dont want to replace the motherboard and reinstall all the software at the moment, and i use mixmiester, fruityloops, reason and such for mixing/creating, and either mixmiester, tracktor, or pcdj fx for dj'ing.
many thanks in advance for your help and advice.
Adrianmikiem ........... your a STAR.......
i didnt know that you could do that.....using the AISO driver allows access to all sorts of outputs..........when i have time im going to have to see what they all do, and what else is available, but the biggest thing is that it has sorted out some of my immediate problems......
i will need to go through all the software to see if i can get access to these outputs from it all, but it definitely works with mixmiester, so i dont need to re plot all the files.
just so that people know, i set the audigy speaker config to 4.0/4.1 in THX setup, and then looked in the advanced audio output section of mixmiester (under output config) and presto....2 independent audio outputs.
dont suppose that anyone knows where to get a complete and detailed manual for what all the software and hardware does and how to configure it all........
HUGE thanks mikiem........ -
What is POP, POP3, and IMAP When I Setup My Email Account in the HP ePrint App?
I have done as much research as I can do in regards to setting up the HP ePrint App Email Accounts. If you do not see your email information listed here, feel free to post it below or contact your internet service provider, phone or email company, or whomever else that might know this. I am certain there are many more that could be added but this is a rather extensive list. I hope you find what you need to finish setting up your email applications.
I have noticed information differs from website to website but as I have learned over time, with domain masking and companies buying out other companies, I just researched all the information I could find and that way if one of the hostnames or ports don’t work, then you can continue to view further into this page to see if that information is the same. At that point, if you can’t find what you need here, I would say you have done all that you can do before contacting the appropriate support team for your email information.
Most of the links are active and the ones listed below should send you directly the pages I pulled this information from but only a few of them were from the actual support sites themselves (Apple support was vague, as well as Microsoft, Macintosh, and commonly used ISPs). Save yourself some time by searching here first. I hope you find what you need in this one-stop-shop and if you get an email address not listed here please post it below and I will add it to this original document.
Lastly, as this information is from forum-based and other unofficial websites, I would like to add that this is a copy/paste/edit-for-easy-reading document I created in my spare time. This is a very long document so I do recommend using the search and find quick keys to search for the email you need but the top part of this has definitions as to what servers, ports, and hostnames are and the basic setup in case you need to know what these options are used for and what they mean.
Below are the most common settings needed to set up most POP3/IMAP Email Clients or Devices:
The following information below can be found at http://www.swestcom.com/Support/q4.htm
“What is POP3?
Post Office Protocol version 3 (POP3) is a standard mail protocol used to receive emails from a remote server to a local email client. POP3 allows you to download email messages on your local computer and read them even when you are offline."
"What is IMAP?
The Internet Message Access Protocol (IMAP) is a mail protocol used for accessing email on a remote web server from a local client. IMAP and POP3 are the two most commonly used Internet mail protocols for retrieving emails. Both protocols are supported by all modern email clients and web servers."
"Main difference between IMAP and POP3:
The POP3 protocol assumes that there is only one client connected to the mailbox. In contrast, the IMAP protocol allows simultaneous access by multiple clients. IMAP is suitable for you if your mailbox is about to be managed by multiple users."
"What is SMTP?
Simple Mail Transfer Protocol (SMTP) is the standard protocol for sending emails across the Internet. SMTP uses TCP port 25 or 2525 and sometimes you can have problems to send your messages in case your ISP has closed port 25 (How to check if port 25 is open?). To determine the SMTP server for a given domain name, the MX (Mail eXchange) should have more information."
"When setting up:
POP - choose POP and the incoming server port will default to 110
IMAP - choose IMAP and the incoming server port will default to 143
All other settings are the same.
Username = [email protected]
Password = the password you set up when you configured your mail box
Incoming Mail Server = mail.yourdomain.com
Outgoing Mail Server= smtp.yourdomain.com
Outgoing Server Requires Authentication (typically found in advanced options or settings)
Do NOT check "Log on Using Secure Password Authentication"
Use the same Username and Password as Incoming or select "Use Same Settings as Incoming"
Outgoing Server Port= 2525 or 587This is subject to change based on the individual preferences of your ISP"
Note - Substitute your actual domain name for "yourdomain.com" and substitute the first part of your email address for "user."
Email Ports
For networks, a port means an endpoint to a logical connection. The port number identifies what type of port it is. Here are the default email ports for:
POP3 - port 110
IMAP - port 143
SMTP - port 25
HTTP - port 80
Secure SMTP (SSMTP) - port 465
Secure IMAP (IMAP4-SSL) - port 585
IMAP4 over SSL (IMAPS) - port 993
Secure POP3 (SSL-POP) - port 995.
For Mozilla, Outlook, Windows mail, Windows Live, Outlook 2003-2010, Entourage for Mac OS, and Mail for Mac OS follow this link: http://help.outlook.com/en-ca/140/cc875899.aspx (this website has not been looked over for validation but may assist in other leads towards the right direction)
Have you ever wished you could use your AOL email account with something else, something more powerful, something more convenient than AOL, something like Outlook, Windows Mail, Outlook Express, or The Bat!? Thanks to the wonders of IMAP, you can.
If you set up your AOL email account in any email client capable of IMAP, you can receive and send messages easily. Even the AOL folders — Spam, Saved, Sent Items and your Trash will be there automatically. Of course, you can also use POP to fetch incoming mail in an uncomplicated fashion.
For instructions on how to assist you with this you can also follow this link: http://email.about.com/od/aoltips/qt/Access_an_AOL_Email_Account_with_any_POP_IMAP_Email_Program.htm
Set Up POP or IMAP E-Mail on an Android G1 How do I set up POP or IMAP E-Mail on an Android Device?
From the home screen, tap Applications > Settings > Accounts & sync > Add account > Manual setup.
On the Incoming settings screen, in the Protocol drop-down menu, select IMAP or POP3. We suggest you select IMAP because it supports more features.
In the Email address and Username text boxes, enter your full e-mail address, for example [email protected], and then select Next. Your user name is the same as your e-mail address.
In the Password text box, enter your password.
In the IMAP server or POP3 server text box, enter your IMAP or POP server name. For information about how to look up the server settings you need to complete this step and other steps in this procedure, see “How do I find the server settings” later in this topic.
In the Security type drop-down menu and Server port text boxes, specify the POP or IMAP settings that you looked up in step 5, and then tap Next. Your e-mail application will check your IMAP or POP settings.
On the Outgoing server settings screen, the Login required option should be selected for you, and the Username and Password text boxes should be filled in.
In the SMTP server text box, enter the SMTP server name you looked up in step 5.
In the Security type drop down menu and Server port text box, specify the SMTP settings that you located in step 5, and click Next.
In the Account name, text box, enter a name for your account (for example “Office 365 email” or “Work email”). In the Your name text box, enter the name you want displayed when you send e-mail to others (for example “Tony Smith”), and then select Finish Setup.
What else do I need to know?
If your e-mail account is the type that requires registration, you must register it the first time you sign in to Outlook Web App. Connecting to your e-mail account through a mobile phone will fail if you haven't registered your account through Outlook Web App. After you sign in to your account, sign out. Then try to connect using your mobile phone. For more information about how to sign in to your account using Outlook Web App, see How to Sign In to Your E-Mail Using a Web Browser. If you have trouble signing in, see FAQs: Sign-in and Password Issues or contact the person who manages your e-mail account.
Information below provided by: http://www.defcon-5.com/support/index.cfm?docid=95
Yahoo:
POP3: pop.mail.yahoo.com Port 995
SMTP: smtp.mail.yahoo.com Port 465
ESMTP should be enabled
SSL: YES
User name must not include the @yahoo.com
GMail:
POP3: pop.gmail.com Port 995
SMTP: smtp.gmail.com Port 465
ESTMP should be enabled
SSL: YES
AOL:
IMAP: imap.aol.com Port 143
SMTP: smtp.aol.com
SSL: NO
ATT World Net:
POP3: ipostoffice.worldnet.att.net Port 995
SMTP: imailhost.worldnet.att.net Port 465
SSL REQUIRED for Incoming and Outgoing
Cox:
NOTE: With Cox you can only use their SMTP servers while on their network.
Central
POP3: pop.central.cox.net
SMTP: smtp.central.cox.net
ESMTP should be enabled
SSL: NO
East Cost
POP3: pop.east.cox.net
SMTP: smtp.east.cox.net
ESMTP should be enabled
SSL: NO
West Cost
POP3: pop.west.cox.net
SMTP: smtp.west.cox.net
ESMTP should be enabled
SSL: NO
Comcast:
POP3: pop3.comcast.net Port 110
SMTP: smtp.comcast.net Port 587
ESMTP should be enabled
SSL: NO
User name must NOT include @comcast.net
Comcast SMART ZONE:
POP3: sz-pop.mail.comcast.net Port 995
SMTP: smtp.compcast.net Port 587
ESMTP should be enabled
SSL: NO
User name must NOT include @comcast.net
Earthlink:
POP3: pop.earthlink.net Port 110
SMTP: smtpauth.earthlink.net Port 587
ESMTP should be enabled
SSL: NO
User name must include @earthlink.net
Hughes Net:
POP3: mail.hughes.net Port 110
SMTP: smtp.hughest.net Port 25
ESMTP should be enabled
SSL: NO
User name must include @hughes.net
Metrocast:
POP3: pop.va.metrocast.net Port 110
SMTP: smtp.va.metrocast.net Port 25
ESMTP should NOT be enabled
User name MUST be full email address
SSL: NO
MSN:
POP3: pop 3 . live. com port #995.
SMTP: smtp.live. com port #25
SSL: YES
ESMTP: should be enabled
User name must have the full email address
NetZero:
POP3: pop.netzero.com Port 110
SMTP: smtpauth.netzero.com Port 25
ESMTP should be enabled
SSL: NO
User name must include @netzero.com
Verizon:
POP3: incoming.verizon.net Port 110
SMTP: outgoing.verizon.net Port 25
ESMTP should be enabled
SSL: NO
The following information is according to a forum comment at the bottom of this webpage concerning HOTMAIL and mail server settings:
“As other web based email services, Hotmail is using the HTTP protocol for connecting you to your mailbox. If you want to send and receive Hotmail emails using an email client software, then your software must support Hotmail HTTP access for your email account. Some email clients, such as Outlook Express or Microsoft Outlook, offer builtin support for Hotmail accounts, so you only have to select HTTP when you are asked to select your email account type and select Hotmail as the HTTP Mail Service Provider.”
Mail Server Settings for Hotmail using the Microsoft Outlook Connector
If you are using Microsoft Outlook & the Outlook Connector, you can define your Hotmail account just like any regular POP3 email account:
Hotmail Incoming Mail Server (POP3) - pop3 . live. com (logon using Secure Password Authentification - SPA, mail server port: 995)
Hotmail Outgoing Mail Server (SMTP) -smtp . live . com (SSL enabled, port 25)
Additional information from this website has not been confirmed or validated as of yet but it does include additional information or perhaps corrected information. If the above steps do not fix the problem with setting up an email account for the HP Apps then read on:
Yahoo! Mail Settings
Yahoo Mail offers standard POP3 access for receiving emails incoming through your Yahoo mailbox, by using your favorite email client software. To setup your email client for working with your Yahoo account, you need to select the POP3 protocol and use the following mail server settings:
Yahoo Incoming Mail Server (POP3) - pop.mail.yahoo.com (port 110)
Yahoo Outgoing Mail Server (SMTP) - smtp.mail.yahoo.com (port 25)
POP Yahoo! Mail Plus email server settings
Yahoo Plus Incoming Mail Server (POP3) - plus.pop.mail.yahoo.com (SSL enabled, port 995)
Yahoo Plus Outgoing Mail Server (SMTP) - plus.smtp.mail.yahoo.com (SSL enabled, port 465, use authentication)
· Google GMail Settings
The Google GMail service offers email client access for retrieving and sending emails through your Gmail account. However, for security reasons, GMail uses POP3 over an SSL connection, so make sure your email client supports encrypted SSL connections.
Google Gmail Incoming Mail Server (POP3) - pop.gmail.com (SSL enabled, port 995)
Outgoing Mail Server - use the SMTP mail server address provided by your local ISP or smtp.gmail.com (SSL enabled, port 465)
MSN Mail Settings
The MSN email service allows you to use the MSN POP3 and SMTP servers to access your MSN mailbox.
MSN Incoming Mail Server (POP3) - pop3.email.msn.com (port 110, using Secure Password Authentication - SPA)
MSN Outgoing Mail Server - smtp.email.msn.com (select "My outgoing server requires authentication")
Lycos Mail Settings
The Lycos Mail Plus service allows you to use POP3 and SMTP servers for accessing your Lycos mailbox.
Lycos Mail Incoming Mail Server (POP3) - pop.mail.lycos.com (port 110)
Outgoing Mail Server - smtp.mail.lycos.com or use your local ISP SMTP mail server
AOL Mail Settings
The AOL email service is a web based system, designed for managing your AOL mailbox via HTTP IMAP access. Unlike Hotmail, you can use any email client to access your AOL mailbox, as long as it supports the IMAP protocol.
AOL Incoming Mail Server (IMAP) - imap.aol.com (port 143)
AOL Outgoing Mail Server - smtp.aol.com or use your local ISP SMTP mail server
Mail.com Mail Settings
The Mail.com email service allows you to use POP3 and SMTP servers for accessing your Mail.com mailbox.
Mail.com Mail Incoming Mail Server (POP3) - pop1.mail.com (port 110)
Outgoing Mail Server - use your local ISP SMTP mail server
Netscape Internet Service Mail Settings
The Netscape e-mail system is web-based, which means you can access their e-mail from any Internet connection. Netscape Internet Service also supports AOL® Communicator, Microsoft® Outlook, Microsoft® Outlook Express, and other POP3 e-mail software. The outgoing mail server needs SSL support, so make sure your email client software supports SSL connections over the SMTP protocol.
Netscape Internet Service Incoming Mail Server (POP3) - pop.3.isp.netscape.com (port 110)
Netscape Internet Service Outgoing Mail Server - smtp.isp.netscape.com (port 25, using a secure SSL connection)
Tiscali Mail Settings
The Tiscali email service allows you to use POP3 and SMTP servers for accessing your Tiscali mailbox.
Tiscali Incoming Mail Server (POP3) - pop.tiscali.com (port 110)
Outgoing Mail Server - use your local ISP SMTP mail server
Freeserve Mail Settings
The Freeserve email service allows you to use POP3 and SMTP servers for accessing your Freeserve mailbox.
Freeserve Incoming Mail Server (POP3) - pop.freeserve.com (port 110)
Outgoing Mail Server - use your local ISP SMTP mail server
Supanet Mail Settings
The Supanet email service allows you to use POP3 and SMTP servers for accessing your Supanet mailbox.
Supanet Incoming Mail Server (POP3) - pop.supanet.com (port 110)
Outgoing Mail Server - use your local ISP SMTP mail se
AT&T SMTP IMAP Server
smtp.att.yahoo.com
SSL Port 465
imap.att.yahoo.com
SSL Port 993
Iphone POP/IMAP Setup
Although I am sure it is out of scope for HP to assist with iPhone setup with mail, contact, calendars, etc so here is a PDF with pictures and a walkthrough from:
https://www.millikin.edu/it/services/HandH/Documents/iPhone%20IMAP%20POP%20Setup.pdf
This hyperlink seems inactive so you may have to copy and paste for a direct walkthrough of this comprehensive pdf.
Lastly if the above information is incorrect or does help, here is one last website to provide you with a complete list that I found located at att.com to assist their customers trying to setup emails in conjunctions with their apps.
Popular POP and IMAP e-mail providers and their incoming server names
http://www.wireless.att.com/support_static_files/KB/KB5892.html
SUBJECT:
Popular POP and IMAP e-mail providers and their incoming server names
What are the AT&T outgoing (SMTP) server names?
SYMPTOM:
ISP E-mail servers
E-mail
ADVISORY:
This information has been retrieved from the proper e-mail provider support pages. This is not an exhaustive list, please refer to your e-mail provider for additional information and compatibility.
FIX:
Outgoing Servers
AT&T outgoing SMTP server policy
Incoming Servers
Users must contact their e-mail service providers for server addresses not included in this list.
Incoming POP3 server uses default port of 110.
Incoming IMAP4 server uses default port of 143.
When using SSL (Secure Socket Layer):
The incoming POP3 port needs to be set to 995.
The incoming IMAP4 port needs to be set at 993.
Internet Service Provider (ISP)
Incoming Server Address
Username
Port
1and1.com
POP: pop.1and1.com
IMAP4: imap.1and1.com
More information at 1and1.com Article.
full e-mail address
POP3: 110
IMAP4: 143
Adelphia
mail.adelphia.net
username only
POP3: 110
Airmail.net (Internet America)
pop3.airmail.net
username only
Alltel.net
(See Windstream)
Ameritech (at&t Yahoo!)
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
AOL (America Online)
Instructions and Disclaimer
username only
IMAP4: 143
AIM Mail
Instructions and Disclaimer
username only
IMAP4: 143
AT&T Broadband Internet (ATTBI)
mail.attbi.com
AT&T Worldnet
ipop.worldnet.att.net
-or-
ipostoffice.worldnet.att.net
Informational only:
AT&T WorldNet e-mail may not be accessible from any device e-mail client due to firewall restrictions implemented by AT&T WorldNet.
See alternatives for accessing AT&T WorldNet:
- Former AT&T Wireless customers
- New and Existing AT&T wireless services customers
full e-mail address
POP3: 995 uses SSL
Bell Atlantic (Verizon)
pop.bellatlantic.net
Bell South
mail.bellsouth.net
username only
Cable One
mail.cableone.net
More information at Cable One.
username only
Cablevision
mail.optonline.net
username only
Charter
pop.charter.net
username only
Clearwire
mail.clearwire.net
More information at Clearwire Article.
full e-mail address
POP3: 110
Comcast
mail.comcast.net
More information at Comcast Article.
username only
POP3: 110
ComNetcom.net (Earthlink)
pop.comnetcom.net
Compuserve Classic
pop.compuserve.com
Compuserve
imap.cs.com
username only
Concentric
pop3.concentric.net
Coqui (Puerto Rico)
pop.coqui.net
Covad
pop3.covad.net
More information on support article.
full e-mail address
POP3: 110
Cox Central
pop.central.cox.net
More information at Cox Article.
username only
POP3: 110
Cox East
pop.east.cox.net
More information at Cox Article.
username only
POP3: 110
Cox West
pop.west.cox.net
More information at Cox Article.
username only
POP3: 110
Cox Business
pop.coxmail.com
More information at Cox Business Article.
full e-mail address
POP3: 110
Earthlink
pop.earthlink.net
full e-mail address
POP3: 110
Eudora
mail.speakeasy.net
Excite
pop3.excite.com - Requires "Premium/Gold" subscription for POP3 access. More information at Excite.com Article.
full e-mail address
POP3: 110
Flash (SBC Yahoo!)
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
Gmail (Google Mail)
Instructions and Disclaimer
full e-mail address
POP3: 995 uses SSL
Go Daddy.com
pop.secureserver.net
More information at Go Daddy.com Article.
full e-mail address
POP3: 110
Grande
mail.grandecom.net
More information at Grande Article.
username only
POP3: 110
GTE.net (Verizon)
mail.gte.net
Hughes Direcway
mail.hughes.net
More information at Hughes Direcway Article.
full e-mail address
POP3: 110
Ix.Netcom.com (Earthlink)
pop.ix.netcom.com
Insight Broadband
mail.insightbb.com (SSL must be enabled for remote access)
More information at Insight Broadband Article.
username only
Juno
POP3/IMAP4 is not available.
More information on support article.
Lightfirst (Avenew)
inmail.lightfirst.com
Mac.com (Apple Computer)
mail.mac.com
POP3 access will not work with "alias" accounts.
More information at Mac.com. Related articles 25275, 51729, and 86685.
username only
POP3: 110
IMAP4: 143
Mail.com
pop1.mail.com
POP3: 110
Mediacom
mail.mchsi.com
More information at Mediacom Article.
full e-mail address
POP3: 995 uses SSL
MEdia Net
POP3 access is currently not available to MEdia Net e-mail accounts. Please access MEdia Net e-mail through the device browser.
POP3: 110
Mindspring (Earthlink)
pop.mindspring.com
full e-mail address
POP3: 110
mMode
pop.mymmode.com
username only
POP3: 110
MSN
pop3.live.com
For subscribers that use (and pay for) MSN as their Internet Service Provider, MSN provides POP3 access to their e-mail. More information on configuring e-mail applications, see Microsoft Article 930008.
Alternatives for accessing MSN from a mobile device:
- Former AT&T Wireless customers
- New and Existing AT&T wireless services customers
full e-mail address
POP3: 995
uses SSL
MSN Hotmail
MSN Hotmail is a HTTP e-mail service so a POP3 server name is not offered by MSN Hotmail. While some 3rd party e-mail servers allow access to Hotmail accounts, this may put e-mail security at risk. AT&T will not house 3rd party e-mail server information.
Alternatives for accessing MSN Hotmail from a mobile device:
- Former AT&T Wireless customers
- New and Existing AT&T wireless services customers
NetAddress or Usa.net
pop.netaddress.com
POP3: 110
Network Solutions
mail.yourdomain.com
Network Solutions Support Page
full e-mail address
POP3: 110
NetZero (United Online)
pop.netzero.com
NetZero E-mail Support Page
username only
POP3: 110
Netscape
pop3.isp.netscape.com
Netscape E-mail Support Page
full e-mail address
POP3: 110
NVBell (SBC Yahoo!)
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
OptOnline
mail.optonline.net
OptOnline Support Article
username only
PacBell (SBC Yahoo!)
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
PeoplePC
mail.peoplepc.com
- or -
pop.peoplepc.com
PeoplePC Support Article
full e-mail address
POP3: 110
Pipeline (Earthlink)
pop.pipeline.com
POP3: 110
Prodigy (SBC Yahoo!)
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
Qwest in Albuquerque, New Mexico
pop.albq.qwest.net
POP3: 110
Road Runner
pop-server.xxxx.com
"xxxx" equals the users e-mail domain, which can be in the region format ("cfl.rr" for Central Florida or "nyc.rr" for New York City) or simply "roadrunner". The domain can be found after the @ symbol in the e-mail address i.e. [email protected] or [email protected]
Road Runner Support Pages - Choose the appropriate region/state and select the Help menu to locate e-mail settings as they are different based on each region/state.
username only
POP3: 110
sbcglobal.net
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
snet.net
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
Surewest
pop.surewest.net
More information at Surewest Article.
full e-mail address
POP3: 110
swbell.net
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
Verizon
incoming.verizon.net
username only
POP3: 110
Verizon (custom server)
pop.verizonemail.net
POP3: 110
Verizon (Yahoo! Mail)
incoming.yahoo.verizon.net
More information at Verizon Yahoo! Article.
full e-mail address
POP3: 110
wans.net
pop.att.yahoo.com
More information on support article.
full e-mail address
POP3: 995
uses SSL
Websitepros
Server information varies on product.
Contact Information
Windstream
pop.windstream.net
More information on support article.
full e-mail address
POP3: 110
Yahoo!
pop.mail.yahoo.com - Requires a monthly subscription fee for POP3 access.
More information on support article.
See Alternatives for accessing Yahoo! E-mail:
- Former AT&T Wireless customers
- New and Existing AT&T wireless services customers
username only
POP3: 995
uses SSL
Yahoo Small Business
pop.bizmail.yahoo.com
"Forwarding" must be disabled and "POP access" must be enabled. Yahoo Small Business Support Page
SPAM/Bulk folders should be emptied if receiving errors occur.
full e-mail address
POP3: 110
If you are viewing information on devices or services, please note: content reflects instructions for devices and services purchased from AT&T. Some differences may exist for devices not purchased from AT&T.
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution!
This question was solved.
View Solution.Just to recap, this is a collection of ports I have collected over time for people who needed this information when setting up the HP ePrint app so that they could view their email from within the app. I am certain other applications also need this information. Although lengthy, I could not find a more comprehensive place to retrieve this information. Feel free to post additional information, faulty information, or other related topics below as this is simply a collection of data and it would be practically impossible to test all of them. Thank you!
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution! -
Optimal Setup for New Time Capsule with Wireless AC
I'm curious to see what the hypotehtical optimal setup for my Time Capsule. I understand that wireless speeds depend on a ton of factors and that part of getting the best connection is just trying different options. I have a new Time Capsule that's connected to the following devices: iPhone 5S; new MacBook Air with wireless AC; old iMac from 2007; old AirPort Express that only supports b/g and a newish Apple TV that supports wireless N, I believe. I was connecting to the network (which was not designated with the 5ghz) and I recently chose the option to label the 5ghz. I'm using that now to stream music with the new iPhone and the Apple TV with no problems, but I have no longer have the option of using the old Airport express because it's an old one. I'm thinking of just getting a new Airport Express and leaving it at that, but wanted to know if anyone has some thoughts on this. I'm sure there's a more concise and direct way to ask this question, but my knowledge is pretty limited here. Thanks in advance.
The Time Capsule is already set up for optimal performance when you open up the box.
You can assign a separate name to the 5 GHz network and point devices that are capable to that network. This works well if the device is located close to the Time Capsule.
But, 5 GHz signals are much weaker than 2.4 GHz signals, so once you move a room or two away, or the signal has to pass through several walls, the 2.4 GHz will be stronger.....and probably faster as well.
But...your device will try to stay locked on the 5 GHz network since you set it up that way.
This type of setup may or may not work best for you. For most users, it is simpler and more effective to use the default settings on the Time Capsule to have both bands use the same network name.
Then, your wireless devices will automatically connect to the signal with the best quality. Best quality may not be the fastest signal since there are lot of factors involved with signal quality. But, if you think about it a bit more, don't you want to have your wireless device connect to the signal with the best quality?
Some users swear by assigning a separate name to the 5 GHz band. I'm not one of them, but If it works well for them and they are happy, then there is no reason to change.
An older AirPort on your network is going to drag down the speeds. You need the new AirPort Express, or better yet an AirPort Extreme if you want to be able to extend the new 802.11ac signal. -
ISP Router/Modem Time Capsule - Optimal Setup
I've read many different threads on this issue but none have really address my question fully, so posting this in the hopes of getting some feedback.
I currently have an ISP that supplies a DSL Modem/Router that serves a dual purpose, provide me with internet and TV service. In Canada it's called Bell Fibe TV. Currently, I have the ISP Modem Wifi OFF, wired it to my Time Capsule and use it to provide Wifi throughout the house.
My question is related to all my other devices and whether they should be connected to the Time Capsule or the ISP Router. Time Capsule and Router are both located in the basement. I have my house hard wired with ethernet to the basement with 3 main outlets, one in the basement for my iMac computer/office, one on the main floor, and one on the top floor.
I have two 3 Apple TV's, one in the basement, one on the main floor and one on the top floor. I use a 5-port ethernet switch on the main floor as I have a variety of different devices there ie: Apple TV, TV Receiver Box, Sonos Player etc. I also have an Airport Express that is wirelessly extending my Wifi.
What is the optimal setup in this situation? I have my Time Capsule on DHCP with router mode OFF (Bridged). Should I be connecting the hard-wired ethernet cables that go throughout the house to the ISP Router/Modem or to the Time Capsule? Does it matter? In recent weeks, I've noticed some odd issues where my Apple TV will lose its network settings and not find the network.
Also, I noticed in BRIDGE mode, there's no way to setup a Guest account on Wifi.
Looking for any suggestions/help on this.
ThanksMy question is related to all my other devices and whether they should be connected to the Time Capsule or the ISP Router.
If the Time Capsule is configured correctly, it makes no difference whether devices connect to the Time Capsule or the ISP modem/router, since both the modem/router and Time Capsule are on the same network.
I have my Time Capsule on DHCP with router mode OFF (Bridged)
That is the correct setting for your situation.
Should I be connecting the hard-wired ethernet cables that go throughout the house to the ISP Router/Modem or to the Time Capsule?
See answer above.
The best practice, wiring wise, would be to connect an Ethernet cable from one of the LAN <--> ports on the modem/router to an Ethernet switch. Then connect the Time Capsule and all other Ethernet connections to the switch.
Performance will not be any better this way, but the network layout and troubleshooting are easier in this type of setup. If you do not want to add a switch, then connect to the most convenient port on either the modem/router or Time Capsule.
Also, I noticed in BRIDGE mode, there's no way to setup a Guest account on Wifi.
That is correct. The Guest Network feature will only work correctly if the Time Capsule is the main router for a network....not a bridge to the network. -
Iphone was working great, even after ios 7 update. However, since ios 7.0.2, the wifi has greyed out and wont work. I have done all the apple recommendations and even reset phone with apple tech help, but still no joy - is apple going to do another update to fix this problem???
Sounds like you have a battry issue but don't want to believe it.
If a car was running fine on one tank of gas, then you filled it up with another tank of gas and it began to run funny, one might suspect that tank of gas. But let's just say coincidence blew a valve-- would you think the new tank of gas was the culprit?
BUT WAIT!! It just might have been! The gas could have been of higher octane and put more more strain on the valves; you know, like going from 87 octane (OS6) to 93 octane (OS7) and showing you the engine was on the edge of compromise.
Sometimes you have to go with common sense. If everything else is ruled out, it must be the battery. And if it runs fine one moment in OS6 but immediately ***** in OS7, I'd believe my battery was suspect-- though comfy-- in OS6 but the OS7 showed its true power.
Moreover, if you had the answer-- or didn't want to believe someone's more competent advice-- why did you even call? You've already shown that you don't know much when you asked if you could go backwards after setting up the new OS as a new phone.
Additonally, if you're such the know-it-all, but yourself the $29 battery and put it in yourself. It's a piece of cake.
<Edited By Host> -
Hi,
I was just wondering if someone could tell me whether i set up my system in the best way possible.
I included a pic i made....hopefully it can help clairfy.
Physical setup:
Modem connected via ethernet cable to WAN of AEBS(new)
Time Capsule LAN connected via ethernet cable to LAN of AEBS(new)
AEBS(old) LAN connected via ethernet cable to LAN of AEBS(new)
Settings:
AEBS(new):
- creating a 5ghz "n" network. Sharing public IP address
- 24mps multicast rate. 25% transmit power. using wide channels
Time Capsule:
- Creating a 5ghz "n" network. same exact name as AEBSnew network. bridge mode.
-24mps multicast rate. 25% transmit power. using wide channels
AEBS(old):
- creating a b/g network. different name than other network mentioned.
- bridge mode.
My internet works fine on both networks... i usually get a transmit rate of 243-300 and an rssi of -48 with the "n" network.
I just want to know if you think this is the optimal setup!...thanks!!Your settings look fine but I'm curious as to why you dropped the power down to 25% on the AEBS(new) and Time Capsule. Why not run them at 100%?
-
Hi, I need help and advice. Basically me and my ex partner both had iphones and synced it with the same computer under the same ID. We split up and now im trying to get all my apps and info onto my new laptop with a new account but it keeps asking me for the old apple ID which she is still using and she changed the password. i tried backing it up but still nohing. When i try to back up purchased items being apps etc its keeps asking for the old one. help
See Recover your iTunes library from your iPod or iOS device. But you'll still need the password.
Once you have the computer authorized to use the account she could change the password again to stop you buying apps on her card (assuming it's not on yours!). It would lock you out of upgrading them too but they should work unless she uses the deathorize all feature.
It depends on how amicable the split is...
tt2 -
HP DeskJet 712c Driver and Wireless Print Server Setup
I have recently purchased a MacBook Pro and am unable to setup my printer to print. Previous to using the MacBook Pro I was using a windows machine without any trouble printing to this printer, however now I can't locate the printer on a list of pre-installed drivers for Mac. I've already checked HP's website and was unable to find any drivers that were for Mac OS. What is a good alternative driver source? Once I do get the driver what would my next steps need to be to set up the wireless print server to work with my mac?
Printer: HP DeskJet 712c
Wireless Print Server: D-Link DP-311P
I would be grateful for guidance to go about this process so that I can use my printer again.
MacBook Pro 2.16GHz Mac OS X (10.4.6)HP-provided drivers don't support network printing. You'll need to install Foomatic (a PPD interpreter), ESP ghostscript (postscript translator) and the 712c PPD from:
http://www.linuxprinting.org/macosx/foomatic/
http://www.linuxprinting.org/showprinter.cgi?recnum=HP-DeskJet712C
Then, since we don't have the auto-setup software for OS X, you need to review the print server manual and find out which IP printing protocol to use. The easiest is HP Jetdirect (called TCP/IP raw port printing in many manuals) if it's available, because it doesn't require the device queue name.
Good luck. -
can I homeshare my music with somebody not on my home network by providing my applied and password in the setup for homesharing
Yes, you can install and use the software on the 2nd machine so long your new company owns the license, the software is used but the same person who is using the primary installation (that is, you).
-
Save as Reduced Size PDF and Save as Optimized PDF do not reduce the file size. What gives?
Save as Reduced Size PDF and Save as Optimized PDF do not reduce the file size. What gives? I used Acrobat 9 to do this for a long time. I recently received new laptop loaded with with Acrobat 10 and it does not work the same. I typically scan 8-10 pages of receipts, combine the files in Acrobat, and then optimize to reduce the size so I can upload with my expense report. Typically, my files were reduced to 200-400 KB. I have a 2 MB file that will not reduce at all.
Bernd, thank you for your attempt to help but the option dialog windows do not contain the same options. There are numerous other posts on this forum about this issue and there is no answer. Clearly, there is an issue. I have submitted this issue to our internal help desk.
-
i'm trying to load photoshop elements 12 on my mac os x and when i click setup.exe i get : You can’t open the application “Setup.exe” because Microsoft Windows applications are not supported on OS X. The premiere elements 12 out of the same box loaded just fine.
An .exe file means you have the windows version. Go get the mac version:
Download Photoshop Elements products | 12, 11, 10
but I hope you have a mac serial number. -
I just updated my iPhone 5 from virgin mobile to ios7, and upon the normal setup i find that i my sim card is not being read; apparently now it isn't supported. please someone help me.
my iphone is and has been locked to one carrier. all i've done is a software update to ios7, like all the other updates since i bought the phone when it was released. same carrier, same sim card. :/
-
I did all of the above recommendations and still Biblexpress is not working. Should not the developer have an update to care for the problem?
You should contact the developer directly to inform them of any issues.
There should be links in the App and if not, there should be links
to the developer's site and support in their presentation in the App Store.
Maybe you are looking for
-
How to add a button in Canvas!?!
Hi, I need help with programming a Canvas object. Excuse my english, I'm not very good. My problem is to add a button in a Canvas class,... There's no add() method in Canvas so how could I solve this. THX WSM
-
Hi, Please send me some useful information on IDOC'S and EDI with relevance to SD module and comman errors with this documents.
-
I do a sort a converted PDF to an excel spreadsheet? The merged fields aren't the same...
-
AGAIN door 205 on my corporate Mac when installing CC Cloud upgrade. I use separate Admin account but still issues. Really pissing me off that this happens with every CC update Guys from Adobe are helpful to fix but issue keeps recurring with EVERY u
-
Question above pretty much sums up the details.