HWIC-3G
Will a 50 ohm load on the antenna port sufficiently drop the received signal level?
For a test, I have an HWIC-3G-CDMA card and an HWIC-4B-S/T card. The BRI card is connected to a satellite data terminal for an ISDN connection. The 2811 router is connected to the cellular network and I want to check the fail-over capability to the ISDN connection. I have been able to disconnect the cellular antenna and the received signal drops to sufficiently fail over to the ISDN connection. However, lately my received signal is great enough that even removing the antenna doesn't lower the received signal enough. Will a 50 ohm load/termination work on the antenna port? Or would an RF antenuator be better?
Mike
I had a similar issue. I used AT commands to manually force lock to WCDMA. But later changed to auto since when WCDMA signal is poor the site loses comms altogether.
However with another site with similar setup, I did the debugs chat script, debug dial events, debug ppp negotiation,
It appears that the chat script tries to dial but the modem does not respond time to time. Customer was in the impression that 3G link would become dormant while not in use. That was not the case. I still have cisco engineer investigating the root cause. But most likely it would be modem firmware issue.
Similar Messages
-
I am trying to get NAT working on a Cisco 2801 with HWIC-4ESW.
I have a 2801 that had a failed Fe0/1 port. The Fe0/1 port was used to give sub-interface Fe0/0.200 access to internet. We installed a HWIC-4ESW into the 2801. I have successfully moved the sub-interfaces ( 0/0.1 , 0/0.100 , and 0/0.200 ) from the Fe0/0 to the HWIC-4ESW. I have reconfigured the Fe0/0 to connect to my ISP. However, I cannot get traffic from vlan200 to pass to the internet over Fe0/0. I have a guest wireless network set for vlan 200. Clients get an IP address in the appropriate range (192.168.200.0), but they cannot get to the internet. Below I have included the results of "sh ip int brief" and some of the "sh run". I think that it is something simple, but I canot get it working.
Help would be appreciated.
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 ***.**.244.194 YES manual up up
FastEthernet0/0.200 unassigned YES unset deleted down
Service-Engine0/0 192.168.100.254 YES TFTP up up
FastEthernet0/1 unassigned YES NVRAM administratively down down
FastEthernet0/1/0 unassigned YES unset up up
FastEthernet0/1/1 unassigned YES unset up up
FastEthernet0/1/2 unassigned YES unset administratively down down
FastEthernet0/1/3 unassigned YES unset administratively down down
Serial0/3/0:0 unassigned YES unset down down
Serial0/3/0:1 unassigned YES unset down down
Serial0/3/0:2 unassigned YES unset down down
Serial0/3/0:3 unassigned YES unset down down
Serial0/3/0:4 unassigned YES unset down down
Serial0/3/0:5 unassigned YES unset down down
Serial0/3/0:6 unassigned YES unset down down
Serial0/3/0:7 unassigned YES unset down down
Serial0/3/0:8 unassigned YES unset down down
Serial0/3/0:9 unassigned YES unset down down
Serial0/3/0:10 unassigned YES unset down down
Serial0/3/0:11 unassigned YES unset down down
Serial0/3/0:12 unassigned YES unset down down
Serial0/3/0:13 unassigned YES unset down down
Serial0/3/0:14 unassigned YES unset down down
Serial0/3/0:15 unassigned YES unset down down
Serial0/3/0:23 unassigned YES NVRAM up up
Vlan1 192.168.1.254 YES NVRAM up up
Vlan100 192.168.100.254 YES NVRAM up up
Vlan200 192.168.200.254 YES NVRAM up up
NVI0 ***.12.244.194 YES unset administratively down down
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.100.1 192.168.100.99
ip dhcp excluded-address 192.168.100.200 192.168.100.254
ip dhcp excluded-address 192.168.200.1 192.168.200.99
ip dhcp excluded-address 192.168.200.200 192.168.200.254
ip dhcp pool Phones
network 192.168.100.0 255.255.255.0
option 150 ip 192.168.100.254
default-router 192.168.100.254
dns-server 192.168.1.8
ip dhcp pool guestwireless
network 192.168.200.0 255.255.255.0
default-router 192.168.200.254
dns-server 8.8.8.8 8.8.4.4
ip cef
no ip domain lookup
ip domain name pwa.com
ip name-server 8.8.8.8
ip name-server 8.8.4.4
controller T1 0/3/0
pri-group timeslots 1-16,24
controller T1 0/3/1
shutdown
gw-accounting aaa
gw-accounting syslog
interface FastEthernet0/0
description Guestwireless route to internet
ip address ***.**.244.194 255.255.255.240
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface Service-Engine0/0
ip unnumbered Vlan100
service-module ip address 192.168.100.200 255.255.255.0
service-module ip default-gateway 192.168.100.254
no cdp enable
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet0/1/0
description trunk to switch
switchport mode trunk
duplex full
speed 100
interface FastEthernet0/1/1
description voice
switchport access vlan 100
interface FastEthernet0/1/2
shutdown
interface FastEthernet0/1/3
shutdown
interface Serial0/3/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn supp-service name calling
no cdp enable
interface Vlan1
description Data
ip address 192.168.1.254 255.255.255.0
interface Vlan100
description voice vlan
ip address 192.168.100.254 255.255.255.0
h323-gateway voip bind srcaddr 192.168.100.254
interface Vlan200
description Guestwireless Data
ip address 192.168.200.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:
ip nat inside source list 10 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.1.1
ip route 192.168.100.200 255.255.255.255 Service-Engine0/0
ip route 192.168.200.0 255.255.255.0 FastEthernet0/0
ip radius source-interface Vlan100
access-list 10 permit 192.168.200.0 0.0.0.255So, I just built this in the lab, and it seemed to work ok. I attached a sparse config, but it does let my host on the GuestWireless get the internet via NAT.
R2#sh ip nat translations vrf GuestWireless
Pro Inside global Inside local Outside local Outside global
icmp 17.12.244.194:5 192.168.200.1:5 1.1.1.1:5 1.1.1.1:5
R2#sh ip route vrf GuestWireless
Routing Table: GuestWireless
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 17.12.244.195 to network 0.0.0.0
17.0.0.0/28 is subnetted, 1 subnets
C 17.12.244.192 is directly connected, FastEthernet0/0
C 192.168.200.0/24 is directly connected, Vlan200
S* 0.0.0.0/0 [1/0] via 17.12.244.195 -
How many vlan can be created on single port of HWIC-2FE
Hi Guys,
I have a router 1921 with a HWIC-2FE.
How many VLAN can I create in each port of HWIC-2FE.
Thank you
SalvoI'm not sure what you are referring to. How many VLANs can be untagged while the port is in access? Or how many VLANs can you pass on a trunk?
-
HWIC-4ESW having same MAC address with fa0/0 from CISCO2811 router.
Hi Expert, I Have a situation where a 2811 is configured with 2 VLANs from HWIC-4ESW module, different ports configured, however the VLAN interfaces have the same mac-address with fa0/0 which causes ARP poisoning problem. It that anyway to solve this problem?
Hi Lee,
My understanding is, this is expected behavior and is due to the hardware limitation of the HWIC-4ESW Module. And I think the HWIC-4ESW Module (at least from my lab testing) always takes the MAC Address of the first on board LAN Interface.
Also, I am able to change the MAC Address of the first on board LAN Interface (Ex.Gig0/0) but I cannot change the MAC Address of the VLAN SVI.
I hope it helps.
Regards,
Arul
** Please rate all helpful posts ** -
Hi,
Does the power supply from aironet 3600 series, AIR-CAP3602I-A-K9 is compliant with french voltage ?
Is it 110-220 input ? How to have a standart french plug or adapter if i bought this item in US ?
Does this hardware can be used in France regarding authorized wireless frequency 2.4 and 5 GHz (802.11a/b/g/n/ac) ?
Do you know if it exist any kind of HWIC module with same wireless performance that it can be used with G2 ISR Router (19xx/29xx/39xx) or previous generation ISR (18xx/2xx/38xx) ?
Best Regards.Does the power supply from aironet 3600 series, AIR-CAP3602I-A-K9 is compliant with french
If you enable this AP, you are likely breaking French law. This AP is configured to be use with "-A" Regulatory Domain.
France should be using "-E".
Power supply issue ... 3600 will work with 15.4w PoE as long as you don't add modules. If you do, you need 20.0w PoE.
You have three choices: PoE switch, Power Injector 3 or Power Brick.
Edit: Just re-read your post about "802.11a/b/g/n/ac" so this confirms you need 20.0 PoE. So the same choices are still applicable: PoE+ switch, Power Injector 3 or Power Brick. -
Hi,
I have a DSL line which is working when connected through Thoman router (Bridge mode) and then to cisco 2800 Router on Ethernet port.
However it doesn't work when connected on ATM0/2/0 on HWIC-1ADSL over POTS. Please help.
Router#show dsl interface
ATM0/2/0
Alcatel 20190 chipset information
Line has not yet been activated.
Modem Status: Down (DMTDSL_DO_OPEN)
DSL Mode: Unknown
Interrupts: 5583908 (0 spurious)
PHY Access Err: 0
Activations: 0
LED Status: OFF
LED On Time: 0
LED Off Time: 0
Init FW: init_AMR-3.0.014_no_bist.bin
Operation FW: AMR-3.0.014.bin
FW Source: embedded
DSL: Training log buffer capability is not enabledHi, thanks for your reply. Please find below config;
interface ATM0/2/0
no ip address
no atm ilmi-keepalive
hold-queue 224 in
interface ATM0/2/0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Dialer1
mtu 1460
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap chap callin
ppp chap hostname
ppp chap password
ppp pap sent-username password
Please let me know if anything else required. -
PVDM2-12DM compatibility with HWIC-1CE1T1-PRI
Hi there,
I'm hoping someone can assist. The setup i am trying to get working is the following
User dials in over POTS to an ISDN30 Line. The ISDN30 line (3rd Party Supplier) is connected to our 2911 via a HWIC-1CE1T1-PRI module. We have inserted a PVDM2-12DM into the router to handle the POTS call.
Problem we have is that we cannot seem to get a modem tone when the user dials in. The ISDN line connects and the debug modem command shows the modem SETUP & INIT phase - see below
Aug 13 12:58:52.341: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x1, cause=0x0, dchan_idb=0x2B2C837C
Aug 13 12:58:52.341: CSM: called_number 'number removed' modem_pool 2AA6CE14 deny_call FALSE
Aug 13 12:58:52.341: CSM: Next free modem = 0/202; statbits = 10020
Aug 13 12:58:52.341: Modem 0/202 CSM: modem is allocated, modems free=-1
Aug 13 12:58:52.341: Modem 0/202 CSM: Incoming call from Unknown to 'number removed', id 0x61
Aug 13 12:58:52.341: Modem 0/202 CSM: (CSM_PROC_IDLE)<--ISDN_CALL
Aug 13 12:58:52.453: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x4, cause=0x0, dchan_idb=0x2B2C837C
Aug 13 12:58:52.453: Modem 0/202 CSM: MODEM_REPORT rcvd DEV_CONNECTED for call_id 0x61
Aug 13 12:58:52.453: Modem 0/202 CSM: (CSM_PROC_MODEM_RESERVED)<--ISDN_CONNECTED
Aug 13 12:58:52.453: Modem 0/202 CSMV12: SETUP(Answer) ISDN 0/0:0
Aug 13 12:58:52.453: Modem 0/202 CSMV12: configured for Answer(A-law) mode, with Null signaling, 0x0 tone detection
Aug 13 12:58:52.453: Modem 0/202 CSMV12: INIT(Answer) ISDN 0/0:0
Aug 13 12:58:52.453: %ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to N/A N/A
Aug 13 12:58:52.485: CSM: csm_modem_event called
Aug 13 12:58:52.485: Modem 0/202 CSM: (CSM_PROC_WAIT_FOR_CARRIER)<--CSM_EVENT_MODEM_SETUP Aug 13 12:58:52.341: CSM:
but there is no modem tone or any more output from the debug commands.
The ISDN line is working fine as a normal ISDN dial in is successful.
Has any one tried this before or is there a known issue with this solution?Updated the IOS but made no difference. Turns out i was missing the line 'network-clock-participate wic 0' Added this to the config and managed to get incoming POTS calls. Only problem now is that the PITS call won't stay up for more than 5 seconds. Looking at the Modem AT registry settings.
-
HWIC-2FE fails to pass ping packets greater than 449 in slots 0,1 on 3845
When we install an HWIC-2FE card in slot 0 or slot 1 of a 3845, the interface fails to pass any ping packet greater in size than 449 bytes. It works fine up until that limit is reached, but then fails completely on a larger size packet. If we move to slot 3 or slot 4 on the 3845, the card works just fine! I have looked through the cisco official bug tracker for HWIC-2FE, but could not find a similar symptom listed. We're running advanced ip services 12.4(24)T7 code on the routers. We're wondering if anyone else has encountered similar problems and may know if there's a software fix or if this is a platform problem with the 3800 series. Thank you for your time.
I'd be tempted to accept your response, but it doesn't explain why the card works when moved to another slot, without making any other changes. My impression is there's some kind of hardware/asic problem with those slots in the 3845.
-
No speed or duplex commands available after installing HWIC
hi guys,
as the title says, i recently installed a HWIC card into our 2801 router running IOS 12.4(24)T8. The card is recognized by the router and is set to GigabitEthernet 0/3/0. I enter the interface mode and apply commands and they are fine except when i try to apply the 'speed' and 'duplex' commands. they are not available under this interface and im not sure why nor am i sure how to rectify it. it is currently not connected only installed.
has anyone else come across this issue before? does anyone have any idea how to fix it so that i can set the speed and duplex? does the cable need to be connected to the interface before i can assign these settings? here are the current interface settings:
interface GigabitEthernet0/3/0
description WAN Link
bandwidth 100000
ip address x.x.x.x x.x.x.x
ip flow ingress
shutdown
no negotiation auto
your help is appreciated
regardsHWIC-1GE-SFP operates in 1 Gbps and full duplex all the time if you are using fibre optic SFP.
Because this interface is WAN-facing, you could potentially rate limit the speed if you use Policy Shaping. -
Losing GPRS connection on HWIC-3G-GSM
Hi,
I have configured Cisco 2801 with HWIC-3G-GSM to work as a GPRS router.
The configuration is:
chat-script gsm "" "atdt*99***1#" TIMEOUT 60 "CONNECT"
chat-script pin "" "at+cpin=xxxx"
interface Cellular0/1/0
ip address negotiated
ip virtual-reassembly
encapsulation ppp
dialer in-band
dialer pool-member 1
dialer-group 1
async mode interactive
ppp chap hostname ""
ppp chap password 0 ""
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
dialer idle-timeout 0
dialer string gsm
dialer persistent delay initial 20
dialer-group 1
access-list 1 permit any
dialer-list 1 protocol ip list 1
line 0/1/0
script startup pin
script dialer gsm
no exec
rxspeed 236800
txspeed 118000
Normally it works fine, but when the signal level is very low it stops to respond. So this is normal, but when the signal is back again, the connection is still lost, or more specific, in my eyes the router (dialer?) doesn't know that the connection is lost.
The test scenario looks like this:
- ping 172.16.1.1 repeat 500
- ping response is received
- I'm disconnecting an antenna
- pings stops working
- connecting back the antenna
- pings are still not working, and all I can do is just to reboot router
I think that it might be a problem with interoperability with a specific GSM carrier.
I have checked what is going on with modem during this test and it looks like this:
- before test
Data Connection Information
===========================
Data Transmitted = 145108 bytes, Received = 139940 bytes
Profile 1, Packet Session Status = ACTIVE
IP address = 172.25.188.5
Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Combined
Packet Service = EDGE (Attached)
Packet Session Status = Active
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = POL, Network = PLUS
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Location Area Code (LAC) = 31942
Routing Area Code (RAC) = 4
Cell ID = 33761
Primary Scrambling Code = 0
PLMN Selection = Automatic
Registered PLMN = Plus GSM , Abbreviated = PLUS
Service Provider =
Radio Information
=================
Current Band = GSM 900, Channel Number = 1
Current RSSI = -56 dBm
Band Selected = GSM all band
Modem Security Information
==========================
Card Holder Verification (CHV1) = Enabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
- after the antenna has been disconnected
Data Connection Information
===========================
Data Transmitted = 359592 bytes, Received = 346840 bytes
Profile 1, Packet Session Status = ACTIVE
IP address = 172.25.188.5
Network Information
===================
Current Service Status = Emergency Only, Service Error = None
Current Service = Combined
Packet Service = None
Packet Session Status = Active
Current Roaming Status = Roaming
Network Selection Mode = Automatic
Country = POL, Network = Orange
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 3
Location Area Code (LAC) = 40100
Routing Area Code (RAC) = 110
Cell ID = 40085
Primary Scrambling Code = 0
PLMN Selection = Automatic
Radio Information
=================
Current Band = GSM 900, Channel Number = 99
Current RSSI = -95 dBm
Band Selected = GSM all band
Modem Security Information
==========================
Card Holder Verification (CHV1) = Enabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
- when I plug back the antena
Data Connection Information
===========================
Data Transmitted = 359592 bytes, Received = 346840 bytes
Profile 1, Packet Session Status = ACTIVE
IP address = 172.25.188.5
Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Combined
Packet Service = EDGE (Attached)
Packet Session Status = Active
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = POL, Network = PLUS
Mobile Country Code (MCC) = 260
Mobile Network Code (MNC) = 1
Location Area Code (LAC) = 31942
Routing Area Code (RAC) = 4
Cell ID = 33761
Primary Scrambling Code = 0
PLMN Selection = Automatic
Registered PLMN = Plus GSM , Abbreviated = PLUS
Service Provider =
Radio Information
=================
Current Band = GSM 900, Channel Number = 1
Current RSSI = -58 dBm
Band Selected = GSM all band
Modem Security Information
==========================
Card Holder Verification (CHV1) = Enabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
I don't really know where is the problem, maybe someone had a similar problem?Hi,
I want to sent some more info;
I have 2 g.shdls conneciton and one 3g ..dialer0 and dilaer1 works for g.shdsl and dialer 3 for 3G conneciton.
IZMIR_BURO# sh dialer
Ce0/2/0 - dialer type = IN-BAND ASYNC NO-PARITY
Dialer pool 5, priority 0
Idle timer (never), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is physical layer up
Dial reason: Persistent Dialer Profile
Interface bound to profile Di3
Time until disconnect never
Current call connected 00:00:04
Connected to internet
Di0 - dialer type = DIALER PROFILE
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Number of active calls = 0
Dial String Successes Failures Last DNIS Last status
Di1 - dialer type = DIALER PROFILE
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Number of active calls = 0
Dial String Successes Failures Last DNIS Last status
Di3 - dialer type = DIALER PROFILE
Idle timer (never), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is physical layer up
Number of active calls = 1
Dial String Successes Failures Last DNIS Last status
internet 18479 2 00:00:04 successful Default
IZMIR_BURO#
IZMIR_BURO#sh int dialer 3
Dialer3 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address will be negotiated using IPCP
MTU 1500 bytes, BW 56 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Interface is bound to Ce0/2/0
Last input never, output never, output hang never
Last clearing of "show interface" counters 2w0d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 6339
Queueing strategy: weighted fair
Output queue: 0/1000/64/6339 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
169997 packets input, 201362608 bytes
94633 packets output, 17498566 bytes
Bound to:
Cellular0/2/0 is up, line protocol is down
Hardware is HSPA/UMTS/EDGE/GPRS-850/900/1800/1900/2100MHz
MTU 1500 bytes, BW 2000 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP TERMsent, loopback not set
Keepalive not supported
Interface is bound to Di3 (Encapsulation PPP)
Last input 00:00:03, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 1/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/2/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1500 kilobits/sec
1 minute input rate 0 bits/sec, 0 packets/sec
1 minute output rate 0 bits/sec, 0 packets/sec
336436 packets input, 205597072 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
298008 packets output, 20549654 bytes, 0 underruns
0 output errors, 0 collisions, 18486 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
IZMIR_BURO#sh caller time
Line User Limit Remaining Timer Type
vty 514 dpcmerkez 00:03:00 00:02:59 Idle Exec
Vi1 \
Vi2 \
IZMIR_BURO#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
83.0.0.0/32 is subnetted, 3 subnets
S 83.66.63.5 is directly connected, Dialer0
is directly connected, Dialer1
C 83.66.163.121 is directly connected, Dialer1
C 83.66.163.109 is directly connected, Dialer0
172.25.0.0/24 is subnetted, 1 subnets
C 172.25.130.0 is directly connected, FastEthernet0/0
10.0.0.0/32 is subnetted, 1 subnets
C 10.150.10.3 is directly connected, Dialer0
is directly connected, Dialer1
S* 0.0.0.0/0 is directly connected, Dialer0
is directly connected, Dialer1
IZMIR_BURO#sh cell
IZMIR_BURO#sh cellular 0/2/0 all
Hardware Information
====================
Modem Firmware Version = K1_0_2_18AP C:/WS/F
Modem Firmware built = 12/29/08
Hardware Version = 1.0
International Mobile Subscriber Identity (IMSI) = 286027450382740
International Mobile Equipment Identity (IMEI) = 011955000180192
Factory Serial Number (FSN) = D66294005801004
Modem Status = Online
Current Modem Temperature = 26 deg C, State = Normal
Profile Information
====================
Profile 1 = INACTIVE*
PDP Type = IPv4
Access Point Name (APN) = internet
Authentication = None
Username: , Password:
* - Default profile
Data Connection Information
===========================
Data Transmitted = 17403856 bytes, Received = 201192534 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Network Information
===================
Current Service Status = Emergency Only, Service Error = Illegal ME
Current Service = Invalid
Packet Service = None
Packet Session Status = Inactive
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = TUR, Network = VODAFONE
Mobile Country Code (MCC) = 286
Mobile Network Code (MNC) = 2
Location Area Code (LAC) = 10151
Routing Area Code (RAC) = 11
Cell ID = 21806
Primary Scrambling Code = 124
PLMN Selection = Automatic
Radio Information
=================
Current Band = WCDMA 2100, Channel Number = 10663
Current RSSI = -77 dBm
Band Selected = Auto
Number of nearby cells = 1
Cell 1
Primary Scrambling Code = 0x7C
RSCP = -82 dBm, ECIO = -7 dBm
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
IZMIR_BURO# -
LMS 4.0.1 - inventory does not provide details about ports on T1/E1 HWIC
Hi,
I'm running LMS 4.0.1 on Windows Server 2008 Standard SP2
In the management system I have Cisco ISR 2921 and Cisco ISR 3945 devices with Cisco 4-Port Clear Channel T1/E1 High-Speed WAN Interface Card.
The issue is that for some of those devices, the inventory does not discover the ports on the T1/E1 HWIC card
When i run a Detailed Inventory report (attached is a screenshot) it shows that there is T1/E1 HWIC in the device, but it states the it has 0 ports. In the same time these ports are operational and are managed by the Fault Monitor application.
Another thing is, when i use CiscoView to monitor/config the device, it does not show color information about these T1/E1 ports (screenshot attached).
The SNMP settings are verified.
Any idea would could be the problem?
KR,
VelinHello Colin,
Thank you for your help.
I have copy the "List Access Servers" in below:
Name Hostname Port
acs001 scvs032.test.com 6021
acs002 scvs033.test.com 6021
acs003 scvs031.test.com 6021
acs004 scvs030.test.com 6021
But, I don't know how to check whether AccessGate is connected to Access Server surely. Because I have Add a New Access Gate following the Oracle Access Manager Access Administration Guide. but it still connect AccessGate unsuccessfully.
Thanks,
Jowvid
Edited by: user12009746 on 2010-5-24 下午10:31 -
Cisco Modem Firmware (HWIC) upgrade Process
HI experts,
I need to upgrade firmware of my LTE ( Hwic) module for the router 2901. I am wondering if this is the part of IOS upgrade process , I mean ones I upgrade IOS to the latest version will it upgrade my modem firmware by own or I need to upgrade LTE modem separately?
can you guys please share your experience here?
any docs on this please?
Thanks!Hi,
The LTE module is part of main Cisco IOS you load into the router. Once you upgrade the IOS, it also applies to the module.
ntegrated 4G LTE WWAN broadband: With the 4G LTE WWAN modem integrated into the router, you gain the benefits of simplified installation and management. In addition, the Cisco 4G LTE WWAN EHWICs are tightly integrated with Cisco ISRs, which run the industry-leading Cisco IOS® Software, giving access to all the advanced features of Cisco IOS Software such as quality of service (QoS), intelligent network queuing, and robust security.
Link:
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/4g-lte-wireless-wan-enhanced-high-speed-wan-interface-card/datasheet_c78-710314.html
HTH -
How to enable routing between HWIC-4ESW and Onboard FE on cisco 1841 router..?
Hello All,
I have a cisco 1841 router, recently i have purchased HWIC-4ESW slot for my router. The module is working fine i could able to see additional FE ports(fe0/0/0,fe0/0/1...).Now problem comes in routing i.e. these HWIC-4ESW ports and Onboard FEs are not communicating.If any bode knows the solution kindly let me know the configuration details..
Thanks,SazzHi,
Look at the configs below.
How can I use IP Routing so communication is possible across all subnets?
Router>en
Router#config t
Router(config)#int fa0/0
Router(config-if)#description ***INTERNET***
Router(config-if)#ip address xxx.xxx.xxx.xxx 255.255.255.252
Router(config-if)#no shut
Router(config-if)#ip nat outside
Router(config-if)#exit
!On-board interface
Router(config)#int fa0/1
Router(config-if)#description ***LAN***
Router(config-if)#ip address 10.0.xxx.xxx 255.255.255.0
Router(config-if)#no shut
Router(config-if)#ip nat inside
Router(config-if)#exit
Router#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Router(vlan)#vlan 10
VLAN 10 modified:
Router(vlan)#vlan 20
VLAN 20 added:
Name: VLAN0020
Router(vlan)#exit
APPLY completed.
Exiting....
Router#config t
Router(config)#int vlan 10
Router(config-if)#ip address 172.16.xxx.xxx 255.255.255.0
Router(config-if)#ip nat inside
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int vlan 20
Router(config-if)#ip address 192.168.xxx.xxx 255.255.255.0
Router(config-if)#ip nat inside
Router(config-if)#no shut
Router(config-if)#exit
!HwIC-4ESW interface
Router(config)#int fa0/0/0
Router(config-if)#switchport mode access
Router(config-if)#switchport access vlan 10
Router(config-if)#exit
!HWIC-4ESW Interface
Router(config)#int fa0/0/1
Router(config-if)#switchport mode access
Router(config-if)#switchport access vlan 20
Router(config-if)#exit
Router(config)#exit
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#config t
Router(config)#ip name-server xxx.xxx.xxx.xxx
Router(config)#ip name-server xxx.xxx.xxx.xxx
Router(config)#exit
Regards, -
Current firmware for HWIC 3G-GSM
Hi all
I am trying tu update the firnmware of a HWIC 3G-GSM within an 1841.
What is the correct firmware?
I have tried
K2_0_7_35 and K1_0_2_18 from
http://tools.cisco.com/support/downloads/go/Model.x?mdfid=281295483&mdfLevel=Sub-Category&treeName=Wireless&modelName=Cisco%203G%20Wireless%20WAN%20%28GPRS%2FEDGE%2FUMTS%2FHSDPA%29%20High-Speed%20Wan%20Interface%20Card&treeMdfId=278875243
and I have also tried
F1_2_3_22 from
http://tools.cisco.com/support/downloads/go/Model.x?mdfid=282745088&mdfLevel=Sub-Category&treeName=Wireless&modelName=Cisco%203G%20Wireless%20WAN%20%28GPRS%2FEDGE%2FUMTS%2FHSDPA%2FHSUPA%29%20Interface%20Card&treeMdfId=278875243
But whenever I issue
microcode reload cellular 0 1 gsm modem-provision
I get
Modem returned following error to Download Start Request:Wrong image for this product
So what might be wrong here?
Thanks for any hint,
Grischa
#sh cellular 0/1/0 hardware
Modem Firmware Version = H1_0_0_7MCAP G:/WS/
Modem Firmware built = 10/26/06
Hardware Version = 1.0
International Mobile Subscriber Identity (IMSI) = 00000
International Mobile Equipment Identity (IMEI) = 352678010376751
Factory Serial Number (FSN) = X28059709101016
Modem Status = Online
Current Modem Temperature = 41 deg C, State = Normal
#sh inventory
NAME: "chassis", DESCR: "1841 chassis"
PID: CISCO1841 , VID: V05 , SN: FTX1145W2RN
NAME: "WIC 1", DESCR: "3G WWAN HWIC-HSDPA/UMTS/EDGE/GPRS-850/900/1800/1900/2100MHz"
PID: HWIC-3G-GSM , VID: V01 , SN: FOC11321GWGHi Grischa,
Did you extract the firmware before the upgrade? archive tar /xtract source-url destination-url
Can you post the log of the whole process?
Do you have the same results with a H firmware, for example H1_1_9_33 ?
Cheers
Marco -
Hi,
I want to use a HWIC-3G-GSM for remote dialin connection. My configuration looks like this:
interface Cellular0/3/0
ip address 192.168.1.19 255.255.255.0
encapsulation ppp
dialer in-band
dialer-group 1
async mode interactive
dialer-list 1 protocol ip permit
line 0/3/0
no exec
transport input all
rxspeed 236800
txspeed 118000
I assume that I need a chat-script, but I cannot find anything for dialin. All chat-scripts try to dialout to provide backup connectivity for a wan failure, but this is not my scenario.
Does anyone know what for AT commands need to be passed to the modem to setup dialin? At the moment, my dialin attempt looks like this (debug chat + ppp nego)
Router#telnet 192.168.1.19
Trying 192.168.1.19 ...
As65 DDR: rotor dialout [best] least recent failure is also most recent failure
As65 DDR: rotor dialout [best] also has most recent failure
As65 DDR: rotor dialout [best]
As65 DDR: Dialing cause ip (s=192.168.1.1, d=192.168.1.19)
As65 DDR: Attempting to dial xxxxxx
CHAT65: Attempting async line dialer script
CHAT65: no matching chat script found for xxxx
CHAT65: Dialing using Modem script: d0efault-d0ials0cript & System script: none
CHAT65: process started
CHAT65: Asserting DTR
CHAT65: Chat script d0efault-d0ials0cript started
CHAT65: Chat script d0efault-d0ials0cript finished, status = Success
%LINK-3-UPDOWN: Interface Async65, changed state to up
As65 DDR: Dialer statechange to up
%DIALER-6-BIND: Interface As65 bound to profile Di1
As65 DDR: Dialer call has been placed
As65 PPP: Using dialer call direction
As65 PPP: Treating connection as a callout
As65 PPP: Session handle[C50001D8] Session id[100]
As65 PPP: Phase is ESTABLISHING, Active Open
As65 LCP: O CONFREQ [Closed] id 178 len 25
As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
As65 LCP: AuthProto CHAP (0x0305C22305)
As65 LCP: MagicNumber 0x15783024 (0x050615783024)
As65 LCP: PFC (0x0702)
As65 LCP: ACFC (0x0802)
As65 LCP: Timeout: State REQsentI am also looking for a way to retrieve sim information, and sms messaged form a cisco router.
Maybe you are looking for
-
HT4436 how do i get a different iCloud email address or change my existing one?
my boyfriend set up my iCloud account with an iCloud email with my full name in it and mispelled my middle name. how do i change it or get a new one?
-
I have not recieved yet my receipt form apple. Money was cut from my bank account. I really need it for my money back withdrawal from my accountant.
-
I have a Wpf FrameworkElement derived control that offers a custom AutomationPeer: using System; using System.Collections.Generic; using System.Text; using System.Windows; using System.Windows.Automation.Peers; using System.Windows.Automation.Provide
-
How do I batch convert wav files to mp3?
Just wondering how I can convert a batch of wav files into mp3 files (including metadata). I was looking thru features in both soundbooth and bridge, but I can't find it (if it exists). Thanls
-
Star Ratings -- From data source
Hi, I have imported a data source to my page and it includes a number which I'd like to convert to stars (graphics). Is there a simple script that I can use to take the number being imported and convert it to a graphic? If the rating is a 2 I'd like