Hyper-V Guest Cannot Find Host Domain Controller 2012 R2

Poweredge T320 server as a Domain Controller, file server and an EXCHANGE 2010 server. There are no other servers at the site.
DHCP is from the firewall.   The DC and the file server will be on the host.
The 2010 EXCHANGE server will be on the guest. The Hyper-V
2012 R2 server cannot see the Domain Controller on the host 2012 R2 server.
The Active Directory is requesting to be promoted to a Domain Controller.
I have a logical or physical error in the installation.
It is asking to promote the Hyper-V guest 2012 R2 to a Domain Controller.
I believe I should have only one Domain Controller in this application.
After the Hyper-V guest can see the host domain controller I will install EXCHANGE 2010.
This is a test environment, offsite.
NIC1 – Host IP:192.168.1.130, 255.255.255.0, Gateway:192.168.1.1, DNS:127.0.0.1
NIC2- Only Hyper-V switch checked
Virtual Switch: 192.168.1.140, 255.255.255.0, Gateway: Blank, DNS: Was 127.0.0.1 didn’t work so I pointed it to the host, 192.168.1.130, but that didn’t work either.
Host adapter: IP:192.168.1.150, 255.255.255.0, 192.168.1.1, DNS Pointing to HOST:162.168.1.130
Active Directory and DNS installed on the guest.
Removed IPv6 from both NICs without any change.
IPAM is not installed on the host or the guest.
Several articles in Internet search didn’t help.
Thanks for your help.

Hi Steve,
I suggest referring to the following links:
REMOTEFX, WINDOWS SERVER & HYPER-V SERVER
http://blogs.technet.com/b/puneetvig/archive/2011/04/21/remotefx-windows-server-amp-hyper-v-server.aspx
RemoteFX (with Hyper-V) is a serious business tool. For games.
http://blogs.technet.com/b/tristank/archive/2012/02/17/remotefx-with-hyper-v-is-a-serious-business-tool-for-games.aspx
Best Regards,
Vincent Wu
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Similar Messages

ACL migration Error : 1210 could not find a domain controller for domain "Test Domain" (Old Domain)

Hi
We are migrating from old domain to new domain. Before live migration, we are trying to check the ACE/ACL migration through SubInACL. We are running the SubInACL on a cluster, which is a member of the Old Domain (Test Domain). We are able to resolve and
ping both Old Domain and the New domain from this cluster machine. We have created a network share on this cluster, which is accessible to all Domain Users of the Old Domain. Both Domains have two way forest level trust. we are trying to migrate
the ACL of this share (\\ClusterMachine\testshare$) to the new domain using SubInACL. We are trying to run the below command to get it done.
subinacl /outputlog=C:\Users\Administrator\Desktop\Migrationlog.txt /subdirectories
\\ClusterMachine\testshare$\*.* /migratetodomain=OldDomain=NewDomain=mappingfile.txt
Mapping file contains : Domain Users=NewDomain_Users
But we are geeting the Error that "1210 could not find a domain controller for domain "Test Domain". Error finding domain name : 1210 the format of the specified computer name is invalid. Current Object "\\ClusterMachine\testshare$"
will not be processed."

Hello,
how in detail is DNS set up in each domain?
Any problems when using nslookup to verify?
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter:

Cannot find host

HI all, I am having a little trouble with my network. I have an WRT54GS router and I am having trouble with the pc with the wirless adapter. It is running Windows ME and I can ping my router with no problem, and there is no problem logging onto my network at all. I just can't log onto my email or internet at all. I get cannot find host or this page cannot be displayed errror. I have the right DNS server and the right isp configured in it but it will not let me log on at all.Any help would be appreciated. Jabe

hi there, I would like to know how many computers do you have there... how may are hardwired and wirelessly connected ones?
who's your ISP?
what's the exact model number of your router?
what's the operating system?
"a helping hand in a community makes the world a universe"

Move Windows Domain Controller 2012 to other Windows Domain Controller 2012 eniveroment

Dear All,
I Have Windows Domain Controller 2012 and but this server have a lot of issue so I need to ask you if I can move this server to other new server as is old server if yes can you please guide me how to do that ?
Regards,

Hello Khaleel,
Your question doesnt specify what kind of errors are there on DC 2012. Try to resolve those errors.
Incase the server cannot be remediated, you can demote the server from being a DC.
you can demote the server using:
http://terrytlslau.tls1.cc/2012/03/domain-controller-demotion-on-windows.html
Please ensure, there is another DC in the domain and the FSMO roles , GC have been transferred to another server.
http://support.microsoft.com/kb/223346/en-us
http://www.archy.net/windows-server-2012-migrating-fsmo-roles/
I LOVE MS..... Thanks and Regards, Kshitiz (Posting is provided "AS IS" with no warranties, and confers no rights.)

Server 2008 Hyper-V Failover Cluster Error on Domain Controller Reboot

I am pretty new to Hyper-V virtual but I have 2 Hyper-V Clusters, each with 2 Nodes and a SAN, 1 Physical Domain Controller for failover cluster management and 1 virtual domain controller as backup. All is running well, no issues. I installed
windows updates on the physical DC and upon reboot, got an error 5120 on cluster 2 that says "Cluster Shared Volume 'Volume1' ('Cluster Disk 1') is no longer available on this node because of 'STATUS_CONNECTION_DISCONNECTED(c000020c)'. All I/O will
temporarily be queued until a path to the volume is reestablished. It pointed to the 2nd node in that cluster as being the issue but when I look at it, it is online and all healthy so I don't understand why the error was triggered and if the DC would
go down for a failure, would that node not be able to access the CSV permanently.
Appreciate any help anyone can provide.

Hi mtnbikediver,
In theory, if you has the correct configuration of cluster the DC restart will not cause the CSV down, does your shared storage installed on your DC? Did you run
the cluster validation before you install the cluster? We strongly recommend you run the cluster validation before you build the cluster, same time please install the recommend update of 2008 cluster first.
Recommended hotfixes for Windows Server 2008-based server clusters
http://support.microsoft.com/kb/957311
I found a similar scenario issue the DC restart will effect the cluster network name resource offline, but it is for 2008R2.
Cluster network name resource cannot be brought online when one of the domain controllers is partly down in Windows Server 2008 R2
http://support2.microsoft.com/?id=2860142
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Error finding a domain controller

Hi,
I have an error in finding a windows domain controller when a PC bootup and does a network access via a Cisco wireless PCMCIA card (AIR PCM-352) managed by Cisco ACU.
This is the situation:
- the operating system of the PC is Windows XP sp2
- the wireless card is an AIR PCM352 with firmware V.5.60.21
- the version of ACU is 6.6.00
- the Access point is a Cisco 1120 (802.11b) with IOS version 12.3(8)JA
- wireless communication is completely open (ssid in guest mode, authentication open ,no wep)
- the ip address of the PC is obtained via DHCP (DHCP server is a Microsoft Server)
I notice a difference between a Cisco PCMCIA card 352 managed by Cisco ACU and by Windows XP.
In fact this error doesn't happen when the WLAN card is controlled by Windows wireless utility.
Is it possible that the startup timing of the Cisco ACU is later than the Window's one?
Does anyone resolved this error?
Thanks in advance
Antonio

Hi Antonio,
Obviously you get the error of the domain not found because your wireless card is not even associated (the wireless card utility hasnt started)
Can you clarify the line "Is it possible that the startup timing of the Cisco ACU is later than the Window's one? " . You mean start the Cisco ACU before the windows one right?
The best way to get around issues like that is to use for example the Odyssey client from Funk and turn on GINA and it should work fine.
Rgds,
Pablo

Wired Network conputer cannot find host printer

I cannot print to host printer on a home wired network.
Printer is HP Photosmart 7520 e all in one.
Host Compter is a Dell Dimension 8100
Pentium 4 1.3 GHz 2.0 GB RAM
Windows XP SP3 host computer.
Netgear N600 Dual Band Router
Model WNDR3400
Network Computer:
Nobilis
Pentium 4 dual core 2.8 GHz
2.5 GB RAM
Linux Mint 17 OS
Both computers share the internet without any problems. The Dell computer prints without any problems. The Dell computer properties 'share this printer' box is checked. I cannot find any IP address for the printer. When I printed out the printer configuration sheet, no IP address was given. When I go to the Control Center->Printers->local-host on the Linux OS, it says it is 'connected to local-host' and 'There are no pinters configured yet'. I then selected 'Add' to add a printer. A 'New Printer' screen comes up and ask to 'Select Device' and also 'Enter URI'. This is where I am stopped in my tracks since I have no 'URI'. Under the 'select device' side there are several options: LPT #1, Serial Port #1, Enter URI, and 'Network Printer'. If Network Printer is selected a dropdown list appears: The main heading is "Find Network Printer'. Selecting 'Find Network Printer' gives various internet protocols (ipp, ipps, https, ipp14, LPD/LPR Host or Printer, Windows printer via Samba, and APP Socket/HP Direct.
The Dell computer has alway worked fine and without problems (XP OS) on any HP printer.
This is where I am stymied! Can someone help me from here.

Can you see the Windows computers when browsing from GO > Connect to server?
Anything different in network connection - you use wireless, they use ethernet, for example?

Reimaged Win 7 PC still cannot ping either domain controller by IP Address, but sees other PCs fine.

OK so this is weird one: I have a Window 7 box that when I went to use it, I discovered that it no longer had access to the internet, but it did see the other PCs on the network. After trying completely different network ports then removing/reading the NIC
and using system restore, I decided to reimage it from scratch and deleted the PC's name from the domain. Here's where it gets strange: Even after a completely wiped and reloaded PC from a known good template, it DOES get an IP address from DHCP/DC/DNS server
(same machine) it can view the other workstations on the domain, but it cannot even get a ping reply back from either of our 2 domain controllers, much less join the domain and it still does not see the internet. This one really has me kerfuffled! It is the
only PC with this problem and I've already scorched the HD.

Hi,
According to your description, the Windows 7 PC has joined the domain before going wrong. And after a series of operations the Windows 7 still can’t access Internet and it can’t ping DC by IP address.
Have you checked the Windows Firewall to see if the firewall blocked the ICMP packet?
Due to the Windows PC can get an IP address from DHCP server as mentioned above, so what IP address the Windows 7 PC get? And what is the IP address of the Windows 7’s DNS server? We can use
ipconfig /all command to print out the TCP/IP configuration. Because we can’t ping DC by IP address, maybe the Windows 7 PC can’t connect to DHCP server. If a DHCP client can’t connect the DHCP server, it can assign a private IP address of
169.254.0.0/16 network to itself. Then the DHCP client will attempt to find an available DHCP server every five minutes. Obviously, computer with a private IP address can’t access Internet.
Best Regards,
Tina

Cannot find any domain in the add new user screen in BPC NW platform

Hi,
While adding new users in BPC NW, I can't see any value in the Avaialable domains dropdown. Hence I am unable to add any users. I am not sure if I have missed any any step during BPC installation.
Can anyone please help and suggest the cause of this error and also suggest the remedial action.
Thanks...

The BPC Installation guide says:
Make sure that the server is configured on the domain or a trusted domain by going to My
Computer --> Properties --> Computer Name --> Change. Make sure the correct domain is specified.
Also...
In this step, you define the .NET service user that is needed to log on to ApShell and run Server
Manager.
Note
This user must be a Windows domain user that installs the .NET server component, is a local
administrator on the machine, has initial access to ApShell (no task security is checked for this
user), is able to browse the Active Directory, and is used to log on to Server Manager. It can be
any user that exists on the domain on which the .NET server is installed. You can verify the
settings in table UJA_SVR_DEFAULT.
a) Stop the IIS and SAP Business Planning and Consolidation instances using the stoposoft.bat
file. For more information, see Tips [page 27].
b) Go to transaction SE38 and run program UJA3_WRITE_SYS_USERS.
c) Assign a single domain user to all user types:
BPC SysAdminUser Domain\<user name>
BPC AdminUser Domain\<user name>
BPC User Domain\<user name>
Also...
The user who creates the initial application set must be the domain user specified in the sysadmin
field of the UJA3_WRITE_SYS_USERS program.
Also...
On the .NET server, check the C:\WINDOWS\system32\drivers\etc\hosts file to ensure that a fully qualified domain
and an IP resolution exists.
Thanks and best regards,
[Jeffrey Holdeman|http://wiki.sdn.sap.com/wiki/display/profile/Jeffrey+Holdeman]
SAP BusinessObjects
Enterprise Performance Management
Regional Implementation Group

Demoting Domain Controller 2012- Need help!!

Hi!
I hve a BIG problem....
I have two DCs.
One is a physical machine(server 2012 std) and the other is virtual(server 2012 r2, on hyper-v).
The thing is that I need to demote the physical machine, which is also the HOST for the virtual machine(lack of resources..)
I have already transferred FSMO roles to the virtual DC and now it is the holder of all roles.
How do I safely demote the physical DC without causing any problem to the virtual DC?
Thank you!
Moriya Saadon

Hello,
there is no risk having only VM DCs. The bigger risk is having just a single DC/DNS/GC. There are reason for physical DCs but a domain can run without it.
Please post an unedited ipconfig /all from BOTH DCs so we can verify some settings.
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter:

Cannot get Guest Services to Start on Virtual Domain Controller

I'm running System Center 2012 SP1 Version 3.1.6018.0
Guests all run Server 2008R2 SP1
I'm having a weird issue when trying to install guests services on a domain controller. On all of the virtual machines of the host, when trying to deploy the guest agent, it fails on all machines with the same error:
Error (2940)
VMM is unable to complete the requested file transfer. The connection to the HTTP server XXXXXXX could not be established.
Unknown error (0x80072ee2)
Recommended Action
Ensure that the HTTP service and/or the agent on the machine powstorehv1.gicw.org are installed and running and that a firewall is not blocking HTTP/HTTPS traffic on the configured port.
I have confirmed that there is no firewall blocking the process so in order to bypass this, I decided to just install the guest agent manually. This worked on all of the virtual machines on the host except for the one that is a Domain Controller.
At the point when it tries to start the service it gives me the following error:
Service 'Microsoft System Center Virtual Machine Manager Guest Agent' (ScvmmGuestService) failed to start. Verify that you have sufficient privileges to start system services.
I have tried with and without UAC enabled and I always run the MSI from an elevated command prompt. I've tried with and without MSIEXEC as well. I have Enterprise and Domain Admin privileges as well and have even tried with the domain administrator account.
At this point I'm not sure why I do not have sufficient privileges to start the service on a Domain Controller but I do understand that permissions are different due to its nature.
Any ideas around this either by installing through SCVMM or manually? Thank you in advance for your time!

After a very painful 10g (EE) installation process
i.e fixing all the following:<snip>
Sat Jul 17 11:40:19 2004
Errors in file
/Users/oracle/admin/db01/bdump/db01_mman_4039.trc:
ORA-07445: exception encountered: core dump [semop+8]
[SIGFPE] [Invalid floating point operation]
[0x41EDB3C] [] []
Sat Jul 17 11:40:21 2004
Errors in file
/Users/oracle/admin/db01/bdump/db01_pmon_4037.trc:
ORA-00822: MMAN process terminated with error
Sat Jul 17 11:40:21 2004
PMON: terminating instance due to error 822
Instance terminated by PMON, pid = 4037==============================================> Any idea on what needs to be done to fix this error.
I remember that i had the very same issue with the
Oracle 9i R2 Developers release.
Any help will be greatly appreciated.You mentioned the 9ir2 release. Do you still have any reference to the 9ir2 software in your environment ? With a little luck you have, and in that case it not so hard to find a solution ...
Ronald.
http://homepage.mac.com/ik_zelf/oracle

Forest trust unable to find Active Directory Domain Controller

I have two domains with a two-way forest trust. We'll call them ForestA and ForestB. They're on seperate subnets. ForestA's DCs are in one physical location. ForestB's DCs are in two locations, one of which is shared with A.
I'm unable to route traffic directly from the remote DC in ForestB to the subnet ForestA is on, so I created a new DC in ForestA that sits on the subnet ForestB uses (basically, I can't route between subnets via the wireless bridge between locations, but
can within the same location).
I found this: http://www.neomagick.net/zen/2008/11/30/using-dns-to-force-a-domain-trust-through-a-specific-domain-controller-dc/
I followed the instructions to set the new DC in forest A to be the only one the remote DC in forest B was aware of.
Nslookup ForestA.com resolves correctly to this DC, but I'm unable to validate the trust relationship, getting the error:
"Windows cannot find an Active Directory Domain Controller for the ForestA.com domain. Verify that an AD DC is available and then try again."
I'd appreciate any help.

In the event viewer, have you found any event id's that corrospond with this error? Have you ensured all ports required are open? Windows firewall is correctly setup? NIC is properly configured?
Statement below taken from: http://technet.microsoft.com/en-us/library/cc961803.aspx
If you receive the following error, ERROR_NO_LOGON_SERVERS while using the Nltest tool to query the secure channel, this is usually indicative of the inability to find a domain controller for that domain. Run nltest /dsgetdc: < DomainName > : to verify
whether you can locate a domain controller. If you are unable to find a domain controller examine DNS registrations and network connectivity.
ADDS Ports:
http://msdn.microsoft.com/en-us/library/dd772723(v=ws.10).aspx

Off-site domain controller

Hi,
I work for a small company who (for reasons of security, cooling, noise and power consumption) cannot run a server at their local office, so there are about 12 PCs in the office along with a D-Link DFL-260E router, and they have a server hosted in an off-site
rackspace centre. The server is running Windows Server 2012 and VPN tunnel is maintained to the D-Link router in the office. The D-Link router acts as the DHCP server for the office.
My predecessor configured the server as a domain controller, but at present none of the PCs in the office are members of this domain - I would like to address this but when I try to join my PC to the domain it fails to find the domain controller.
The error was: "DNS name does not exist."
(error code 0x0000232B RCODE_NAME_ERROR)
Are there any DNS settings I need to set up on the D-Link router and/or the off-site server to allow the PCs to join the domain?
The issue is possibly further complicated by the fact that the internal domain has been configured to use the same "mycompanyname.com" domain name as our public website - which is hosted entirely separately by a web hosting company and as such
"mycompanyname.com" resolves to the IP address of the web hosting server. I've read up a bit on split-dns but I'm not sure how to configure the router or server to accommodate it.
I would like to avoid tearing down and rebuilding the domain because it is a live environment and various other services running on the Windows Server are preconfigured to authenticate against it.
Any advice would be greatly appreciated.
Thanks.

HI
Domain Join
First we need to Test it :)
take one PC and assign DNS IP address as the Domain controller, Try to ping your domain name and it should resolve to the IP Domain controller IP address.
Then , Join the PC to Domain and you will be able to do it with out any issues.
Second
Yes, you need a split DNS configuration, YOu need all the public web address added on to the local domain controller.
Example : if you have a site xx.com and its poing to 195.x.x.x IP adress
on the domain controller add the host record point to public IP address for all web address.
Test access from the PC which we joind to domain
If you are able to access all sites and services, let do it for all
On DHCP, change the DNS to your domain controller and start adding PC to domain

Sysvol rebuild on a single domain controller

Hello there
Platform: Server 2008 R2 single Domain controller
A clients server above lost power with an unexpected shutdown over the week end and couldn't logon to the domain.  However they can browse the network and open shares on the server. Connections to the Active directory failed and
DCDIAG reported failure to connect to the Global Catalogue server, along with other failures. The event logs show the following:
File Replication Service
Event ID 13561 Jrnl_wrap_error
Event ID 13566 declares FRS is scanning the volume but it cannot become a domain controller until finished... which it never does.
Directory Services
Event ID 1355 The Specified domain either does not exist or could not be contacted.
Finally running net share reveal that the SysVol is Netlogon shares are not available.
First of all I looked at the common JRNL fix of changing the of changing the DWORD Enable Journal Warp Automatic Restore to 1. But, it was already set to 1, when it should have been 0. So I am not sure what that means. I tried changing
it back with FRS service restarts but to no avail.
I have seen numerous entries about recovering the sysvol, but most involve pulling copies from other DC's, of which there are none. I do have a valid Windows backup with System state and Sysvol, which I feel I may be heading with this. So are there any other
paths I should be looking at, or is a restore from backup the only option?
Many thanks in advance
MIS5000

Hello Ahmed and thanks for your reply
NSLookup returns correct values both ways for IP and FQDN
I also carried out some checks following your article. There were a couple of records pointing to the old server for last year which I have deleted. In the meantime I have pasted DCDIAG below for your thoughts I where I should be looking. There
is for example a returned test fail on a the time server at the foot of the report
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
Directory Server Diagnosis
Performing initial setup:
   Trying to find home server...
   Home Server = Server-RDS
   * Identified AD Forest.
   Done gathering initial info.
Doing initial required tests
   Testing server: Default-First-Site-Name\SERVER-RDS
      Starting test: Connectivity
         ......................... SERVER-RDS passed test Connectivity
Doing primary tests
   Testing server: Default-First-Site-Name\SERVER-RDS
      Starting test: Advertising
         Fatal Error:DsGetDcName (SERVER-RDS) call failed, error 1355
         The Locator could not find the server.
         ......................... SERVER-RDS failed test Advertising
      Starting test: FrsEvent
         There are warning or error events within the last 24 hours after the
         SYSVOL has been shared. Failing SYSVOL replication problems may cause
         Group Policy problems.
         ......................... SERVER-RDS passed test FrsEvent
      Starting test: DFSREvent
         ......................... SERVER-RDS passed test DFSREvent
      Starting test: SysVolCheck
         ......................... SERVER-RDS passed test SysVolCheck
      Starting test: KccEvent
         ......................... SERVER-RDS passed test KccEvent
      Starting test: KnowsOfRoleHolders
         ......................... SERVER-RDS passed test KnowsOfRoleHolders
      Starting test: MachineAccount
         ......................... SERVER-RDS passed test MachineAccount
      Starting test: NCSecDesc
         Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have
            Replicating Directory Changes In Filtered Set
         access rights for the naming context:
         DC=ForestDnsZones,DC=ppp,DC=com
         Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have
            Replicating Directory Changes In Filtered Set
         access rights for the naming context:
         DC=DomainDnsZones,DC=ppp,DC=com
         ......................... SERVER-RDS failed test NCSecDesc
      Starting test: NetLogons
         Unable to connect to the NETLOGON share! (\\SERVER-RDS\netlogon)
         [SERVER-RDS] An net use or LsaPolicy operation failed with error 67,
         The network name cannot be found..
         ......................... SERVER-RDS failed test NetLogons
      Starting test: ObjectsReplicated
         ......................... SERVER-RDS passed test ObjectsReplicated
      Starting test: Replications
         ......................... SERVER-RDS passed test Replications
      Starting test: RidManager
         ......................... SERVER-RDS passed test RidManager
      Starting test: Services
         ......................... SERVER-RDS passed test Services
      Starting test: SystemLog
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   18:49:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   18:54:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   18:59:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:04:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:09:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0xC0001B58
            Time Generated: 02/23/2015   19:12:34
            Event String:
            The Diagnostic Service Host service failed to start due to the follo
wing error:
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:14:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         A warning event occurred. EventID: 0x00001695
            Time Generated: 02/23/2015   19:16:19
            Event String:
            Dynamic registration or deletion of one or more DNS records associat
ed with DNS domain 'ppp.com.' failed. These records are used by other computers
to locate this server as a domain controller (if the specified domain is an Act
ive Directory domain) or as an LDAP server (if the specified domain is an applic
ation partition).
         A warning event occurred. EventID: 0x00001695
            Time Generated: 02/23/2015   19:16:19
            Event String:
            Dynamic registration or deletion of one or more DNS records associat
ed with DNS domain 'ForestDnsZones.ppp.com.' failed. These records are used by
other computers to locate this server as a domain controller (if the specified d
omain is an Active Directory domain) or as an LDAP server (if the specified doma
in is an application partition).
         A warning event occurred. EventID: 0x00001695
            Time Generated: 02/23/2015   19:16:20
            Event String:
            Dynamic registration or deletion of one or more DNS records associat
ed with DNS domain 'DomainDnsZones.ppp.com.' failed. These records are used by
other computers to locate this server as a domain controller (if the specified d
omain is an Active Directory domain) or as an LDAP server (if the specified doma
in is an application partition).
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:19:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         A warning event occurred. EventID: 0x0000000C
            Time Generated: 02/23/2015   19:21:44
            Event String:
            Time Provider NtpClient: This machine is configured to use the domai
n hierarchy to determine its time source, but it is the AD PDC emulator for the
domain at the root of the forest, so there is no machine above it in the domain
hierarchy to use as a time source. It is recommended that you either configure a
reliable time service in the root domain, or manually configure the AD PDC to s
ynchronize with an external time source. Otherwise, this machine will function a
s the authoritative time source in the domain hierarchy. If an external time sou
rce is not configured or used for this computer, you may choose to disable the N
tpClient.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:24:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:29:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:34:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         A warning event occurred. EventID: 0x00001695
            Time Generated: 02/23/2015   19:37:48
            Event String:
            Dynamic registration or deletion of one or more DNS records associat
ed with DNS domain 'ppp.com.' failed. These records are used by other computers
to locate this server as a domain controller (if the specified domain is an Act
ive Directory domain) or as an LDAP server (if the specified domain is an applic
ation partition).
         A warning event occurred. EventID: 0x00001695
            Time Generated: 02/23/2015   19:37:48
            Event String:
            Dynamic registration or deletion of one or more DNS records associat
ed with DNS domain 'ForestDnsZones.ppp.com.' failed. These records are used by
other computers to locate this server as a domain controller (if the specified d
omain is an Active Directory domain) or as an LDAP server (if the specified doma
in is an application partition).
         A warning event occurred. EventID: 0x00001695
            Time Generated: 02/23/2015   19:37:48
            Event String:
            Dynamic registration or deletion of one or more DNS records associat
ed with DNS domain 'DomainDnsZones.ppp.com.' failed. These records are used by
other computers to locate this server as a domain controller (if the specified d
omain is an Active Directory domain) or as an LDAP server (if the specified doma
in is an application partition).
         A warning event occurred. EventID: 0x000003F6
            Time Generated: 02/23/2015   19:39:23
            Event String:
            Name resolution for the name crl.microsoft.com timed out after none
of the configured DNS servers responded.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:39:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         An error event occurred. EventID: 0xC00038D6
            Time Generated: 02/23/2015   19:41:54
            Event String:
            The DFS Namespace service could not initialize cross forest trust in
formation on this domain controller, but it will periodically retry the operatio
n. The return code is in the record data.
         An error event occurred. EventID: 0x0000041E
            Time Generated: 02/23/2015   19:44:31
            Event String:
            The processing of Group Policy failed. Windows could not obtain the
name of a domain controller. This could be caused by a name resolution failure.
Verify your Domain Name System (DNS) is configured and working correctly.
         ......................... SERVER-RDS failed test SystemLog
      Starting test: VerifyReferences
         ......................... SERVER-RDS passed test VerifyReferences
   Running partition tests on : ForestDnsZones
      Starting test: CheckSDRefDom
         ......................... ForestDnsZones passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... ForestDnsZones passed test
         CrossRefValidation
   Running partition tests on : DomainDnsZones
      Starting test: CheckSDRefDom
         ......................... DomainDnsZones passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... DomainDnsZones passed test
         CrossRefValidation
   Running partition tests on : Schema
      Starting test: CheckSDRefDom
         ......................... Schema passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... Schema passed test CrossRefValidation
   Running partition tests on : Configuration
      Starting test: CheckSDRefDom
         ......................... Configuration passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... Configuration passed test CrossRefValidation
   Running partition tests on : ppp
      Starting test: CheckSDRefDom
         ......................... ppp passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... ppp passed test CrossRefValidation
   Running enterprise tests on : ppp.com
      Starting test: LocatorCheck
         Warning: DcGetDcName(GC_SERVER_REQUIRED) call failed, error 1355
         A Global Catalog Server could not be located - All GC's are down.
         Warning: DcGetDcName(TIME_SERVER) call failed, error 1355
         A Time Server could not be located.
         The server holding the PDC role is down.
         Warning: DcGetDcName(GOOD_TIME_SERVER_PREFERRED) call failed, error
         1355
         A Good Time Server could not be located.
         Warning: DcGetDcName(KDC_REQUIRED) call failed, error 1355
         A KDC could not be located - All the KDCs are down.
         ......................... ppp.com failed test LocatorCheck
      Starting test: Intersite
         ......................... ppp.com passed test Intersite
Thanks Ahmed
MIS5000

How to join a Domain Controller Server to an two-tier (SQL Server 2012) and Sharepoint 2013 (SP2013) farm

Hi,
I am trying to build a 3-tier SharePoint 2013 farm.
1. SQL Server 2012, Windows 2012 VM
2. DC Server, Windows 2012 VM
3. SharePoint 2013, Windows 2012 VM
I didn't built the DC server. Someone else did. However, I created about 14 service domain user accounts for SQL Server and SharePoint install and operation.
I was able to join the SQL Server into the SharePoint server farm using SharePoint 2013 Product Configuration Wizard. When I start the Central Admin, and click on Servers in the Farm, I only see the SharePoint server and SQL server,
but the DC server is not listed. Any suggestion on what did I miss?
Thanks
Jean

You cannot join the Domain Controller to your SharePoint farm. You must instead join each server from that farm to the domain that is served up by that DC. You will want to uninstall SharePoint and probably SQL before you do this. If it's
an option, I would re-provision your VMs completely and start fresh. Once you login to a new server, join that server to the target domain like this:
http://www.petri.co.il/join-windows-server-2012-to-domain.htm
You'd have to ensure that your DNS resolves to the target domain on the server being joined to the domain. If it doesn't, you can always use HOSTS entries to overcome that in the short term.
Once you've joined both the future SQL and SharePoint servers to the domain, you can install SQL Server and then SharePoint on their prospective servers to create your farm.
I trust that answers your question...
Thanks
C
|
RSS |
http://crayveon.com/blog |
SharePoint Scripts | Twitter |
Google+ | LinkedIn |
Facebook | Quix Utilities for SharePoint

Hyper-V Guest Cannot Find Host Domain Controller 2012 R2

Similar Messages

Maybe you are looking for