I am getting error -10086 while doing an external calibratio​n of PCI-MIO-16​E4 board.

I am using Labview 6.0.2 with ni-daq 6.8.1 on windows 2000.

I am pasting an answer that was asked a while back that may help answer yours.
Title:
Error 10086 When Using Calibate_E_Series Function to do an External Calibration.
Problem:
In this particular case, the customer was trying to do an external calibration on his E Series board using the E Series Calibration Fixture to connect a power supply and DMM to the board. He made the following NI-DAQ call, "Calibrate_E_Series(2, nd_ext_calibrate, nd_ni_sw_area, 6.1)", but received error 10086, "Invalid reference voltage".
Solution :
This customer was trying to use a power supply to provide the external reference voltage to calibrate the board with. However, a power supply cannot provide a steady enough signal for NI-DAQ to be able to narrow in on a value. A
source 4 to 10 times more accurate than the board should be used, such as an actual calibrator.

Similar Messages

  • USER IS GETTING ERROR MESSAGE WHILE DOING PM ORDER COLLECTIVE CONFIRMATION

    Dear,
    i have query from my client that user is getting error message " no status object is available for cre o/o/o while doing pm order confirmation. My client is using sap MRS . I Recommend the client to run program ZKBEDREP in se38 and still they are facing the same error.Can any body help me in solving this.

    Hi,
    Please see if this thread helps
    System status not avilable for one of the component - Conf. can't be done
    Regards,

  • Error Message while doing Order CLSD

    Hi,
    I am getting error message while doing Order CLSD...
    Error Msg: Invalid cost element(XXXX) for reservation item 010.
    please suggest me...how to solve this issue.
    regards,
    Venkatesan Anandan

    Hi Venkatesan,
    I had replied and asked for one clarrification and to check same at your end.
    Is your Cost Element mapping done with cost cost center used in order settlement rule.
    Also check for Material Master Change document for Valuation Class change and revert back in this thread.

  • Error message while doing MIGO.

    Hi,
    I am getting error message while doing MIGO. Can some one help me out in this issue.
    Consolidated companies 0 and 5686 are different
    Message no. F5 080
    Diagnosis
    The number of the affiliated company must be clear for the selected document type for all line items. In this case at least two different companies or a company in connection with a business partner who does not belong to a company are stated.
    Procedure
    If you selected the correct accounts, you must enter the document with a document type that allows cross-company posting. Otherwise, please correct the entered account.
    Thanks in Advance,
    Subhajo

    Check Fi customizing in OBA7.
    As you mentioned MIGO, I assume you are doing goods receipt, so you use document type WE.
    Within WE you must not have selected  the field inter-company posting .
    Best you place the cursor into this field and press F1 for detailed explanation,

  • Getting Error "Apple ID does not have permission to access iTunes Connect" while logging to iTunes. Please help me in this regard

    Getting Error "Apple ID does not have permission to access iTunes Connect" while logging to iTunes. Please help me in this regard
    Regards,
    Amar

    See the "More Like This" section over there ===============>
    In the future, search before posting.

  • I am getting error (-1) while updating my iPhone 4 to iOS 5.1. The phone has gone into a recovery mode. Restore fails every time at "restoring the firmware" stage. Striped bar remains for a long time, then shows "error (-1)" and the restore fails. Help!

    I am getting error (-1) while updating my iPhone 4 to iOS 5.1. The phone has gone into a recovery mode. Restore fails every time at "restoring the firmware" stage. Striped bar remains for a long time, then shows "error (-1)" and the restore fails. I have been doing it for last 12 hours. Help!

    Thanks for your reply Michalo. I am in India and here Apple care does not work on Sundays. I have been without my phone for the entire day. Perhaps tomorrow will bring some respite. There is not solution to "error (-1)" on any forum it seems. I found one forum which suggested use of Tiny Umbrella. Any idea about that?

  • Getting error 3253 while downloading ios 6.1.3 on windows 7.

    I am getting error 3253 while downloading ios 6.1.3 on my windows 7. I am having version 11.0.2.26 of i-Tunes. I tried downloading manier times but not worth after downloading half of the size i lost my network connection and error -3253 pop up.  I also turned off windows firewall but nothing is worth. Prvious time when i was running with microsoft xp i just download internet explorer 8 and it fixed my problem, but i don't get solution for windows 7, Please help me out

    "Error 3000" through "3999"
    Alerts with codes in the 3000 range generally mean that iTunes cannot contact the gs.apple.com server on ports 80 or 443. This may be because out-of-date or incorrectly configured security or firewall software is interfering, or due to your Internet proxy settings. If you are using a proxy, try removing the proxy settings, or using a known-good network. If that does not resolve the issue, follow iTunes for Windows: Troubleshooting security software issues.
    Hope it helps

  • I'm getting error 5000 while trying to backup my phone before I can run an update

    I'm getting error 5000 while trying to backup my phone so I can run an update. I'm getting a message that says my back up is corrupt. What does that mean and how can I fix it?

    Hi
    This is an easy Q: to set - but there is no simple and plain answer only a lot of more or less plausibly suggestions.
    Error -50 = paramErr  Error in user parameter list
    Can there be any external hard disks - if so How is/are it/they formatted ?
    If so it Must be Mac OS Extended (hfs) if used for Video.
    UNIX/DOS/FAT32/Mac OS Exchange - works for most but not for VIDEO.
    What this means in Your situation is above me.
    • free space on internal boot hard disk 11Gb is on the limit to work when You select Export and might be it.
    Video used - there are several video formats/codecs and iMovie can not use all of them, they evolve to fast.
    • So try to find out by opening a raw video in QuickTime-player and then open Inspector (cmd+I) and read
    Video Format/Codec: nnnnnnnn
    What does it read ?
    Pictures
    • in what format ? .jpg, .bmp, .tif, else ?
    Audio
    • from where/what format ? iTunes, .avi, .mp3, .aiff, else ?
    I convert all audio to .aiff - in iTunes I burn out as an Audio-CD .aiff (not .mp3) and use the files on this in my movie projects.
    Some times it's needed to trash the "com.apple.iMovie.plist" file in You USER-Library/Preferences (not Library on Root level (when opening Macintosh HD) - but the one in Your home folder.
    Many users has not observed that there are TWO libraries.
    • Library - at root level
    • Library - in user/account folder - THIS IS THE ONE to look into
    from Luke Burns
    I fixed the problem.. but it was very, very strange. I had a very long section for credits and set the line spacing to 1.0.. for some reason this caused it. I removed it, and it worked fine. I put it back, and I couldn't preview or play the video.
    I don't know why that could cause that big of a problem, but it did..
    Yours Bengt W

  • I am getting error message while attempting to upgrade the software to iOS 6.1.3

    Hi,
    Need help on this, i am getting error message while attempting to upgrade the software to iOS 6.1.3

    The Current iOS for the iPhone 4s is iOS 7
    How to update your iPhone, iPad, or iPod touch

  • I am getting error 205 while trying to install Creative Cloud. I already had chated with support, Uninstalled CC and tried to install it again. From the Adobe site, the page keeps loading eternally, from the previous installer, it gives me error 205. What

    I am getting error 205 while trying to install Creative Cloud. I already had chated with support, Uninstalled CC and tried to install it again. From the Adobe site, the page keeps loading eternally, from the previous installer, it gives me error 205. What to do? Give up on CC?
    This is not the first time I get it, and it seems a recurring problem.

    Milliet are you on a managed network?  If not then please see Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html for information on how to resolve error 205.

  • Getting error msg while inserting a record

    HI
    Am getting error msg while am inserting a new record. Am unable to view the data that i inserted in to database. If any one can help in sorting of the problem plz help. I used the following code in Application Module(AM) and Controller(CO)
    processRequest()
    -- am.invokeMethod("insertmethod");
    processFormRequest()
    -- if(pageContext.getParameter("Create")!=null)
    -- am.invokeMethod("savemethod");
    In AM Code
    public void insertmethod()
    EOVOImpl vo=getEOVO1();
    if(!vo.isPreparedForExecution())
    {    vo.executeQuery(); }
    Row ro=vo.createRow();
    vo.insertRow(ro);
    ro.setNewRowState(Row.STATUS_INITIALIZED);
    public void savemethod()
    {   OADBTransaction oa=getOADBTransaction();
    oa.commit(); }
    Error
    Attribute SummaryFlag in kiInsertAM.kiInsertEOVO1 is required

    Hi,
    Either on the form you don't have SummaryFlag field or you forgot to map VO attribute i.e. SummaryFlag to that field.
    If you don't have SummaryFlag field on form then you need to set it programatically before committing record.
    Please check and let us know.
    Regards,
    Mukesh Uchaniya

  • My MacBook Pro gets very slow while doing  work like watching movies and using net .. video gets lag very often

    My MacBook Pro gets very slow while doing  work like watching movies and using net .. video gets lag very often and while surffing on net it gets very slow ...

    First, back up all data immediately, as your boot drive might be failing.
    There are a few other possible causes of generalized slow performance that you can rule out easily.
    Reset the System Management Controller.
    If you have many image or video files on the Desktop with preview icons, move them to another folder.
    If applicable, uncheck all boxes in the iCloud preference pane.
    Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
    Check your keychains in Keychain Access for excessively duplicated items.
    Boot into Recovery mode, launch Disk Utility, and run Repair Disk.
    Otherwise, take the steps below when you notice the problem.
    Step 1
    Launch the Activity Monitor application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
    Select the CPU tab of the Activity Monitor window.
    Select All Processes from the menu in the toolbar, if not already selected.
    Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
    Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
    Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
    Step 2
    If you have more than one user account, you must be logged in as an administrator to carry out this step.
    Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
    When posting a log extract, be selective. Don't post more than is requested.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

  • Getting Error SAPHTML_E_CALL_METHOD_FAILED while displaying payload in MONI

    HI Experts,
    Iam getting error " SAPHTML_E_CALL_METHOD_FAILED:" While displaying message payloads in SXMB_MONI.
    Facing this problem for all the messages,Issue is in production system.
    Cloud you please help me in in resolving this error.
    Thanks in Advance,
    Regards,
    Seshu.K

    Hi,
    This seems like some Basis config issue. might be a problem in your MONI settings,
    Go to SXMB_ADM and inside Integration Engine configuration
    ->add LOGGING and LOGGING_SYNC under category RUNTIME and give current value = 1 (active). Save it then.
    Also check if sapgui version if the latest one. Maybe you can solve the problem by upgrading sapgui.
    The following SAP notes might help: 1018948, 1072109
    Regards,
    Souvik

  • Errors encountered while doing BCC Full deployment in the Applying phase

    Errors encountered while doing BCC Full deployment in the Applying phase. The stack trace is as below:-
    **** Warning    Fri Aug 02 09:43:24 BST 2013    1375433004207   /atg/epub/PublishingRepository  Using default JDBC type for: project:tar814 could not find this column in the table's meta data
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574278   /atg/epub/DeploymentServer      Run first apply phase: true
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574279   /atg/epub/DeploymentServer      Switch switchable CA datasources:
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574279   /atg/epub/DeploymentServer        isDeploymentRollback(): false
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574284   /atg/epub/DeploymentServer        Current Target live datasource name: DataSourceA
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574285   /atg/epub/DeploymentServer        CA switching datasource: /atg/commerce/jdbc/ProductCatalogSwitchingDataSource_production
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574285   /atg/epub/DeploymentServer          Current live datasource name: DataSourceB
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574285   /atg/epub/DeploymentServer          Current offline datasource name: DataSourceA
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574286   /atg/epub/DeploymentServer          The current CA live datasource is pointing at the Target offline datasource. No CA switch necessary.
    **** debug      Fri Aug 02 09:52:54 BST 2013    1375433574287   /atg/epub/DeploymentServer      Switchable CA datasources switched.
    **** info       Fri Aug 02 09:52:54 BST 2013    1375433574307   /atg/epub/DeploymentServer      DirectSQLReplicationAdapter: Starting FIRST phase data transfer.
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver SQL Statement Failed: [++ReplicationSQL++]
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver INSERT
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver INTO ndcatalog2.extn_block_link
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver      (
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        renderer_id,
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        link,
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        block_id
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver      )
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver SELECT
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        t1.renderer_id,
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        t1.link,
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        t1.block_id
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver FROM
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        extn_block_link t1,
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        extn_block t2
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver WHERE t2.asset_version =
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        ( SELECT MAX ( asset_version )
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver          FROM extn_block
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver          WHERE
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver            (
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver              (
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver                checkin_date <= ?
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver              )
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver            )
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver            AND branch_id = ?
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver            AND block_id = t2.block_id
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver        )
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver AND t2.version_deleted = ?
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver AND t2.branch_id = ?
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver AND t1.asset_version =  t2.asset_version
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver AND t1.block_id = t2.block_id
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver -- Parameters --
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver p[1] = {pd: checkin_date} 2013-07-30 10:23:57.867 (java.sql.Timestamp)
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver p[2] = {pd: branch_id} 10500 (java.lang.String)
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver p[3] = {pd: version_deleted} false (java.lang.Boolean)
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver p[4] = {pd: branch_id} 10500 (java.lang.String)
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver [--ReplicationSQL--]
    **** Error      Fri Aug 02 09:53:12 BST 2013    1375433592737   /com/screwfix/content/block/BlockRepository-ver         java.sql.SQLSyntaxErrorException: ORA-00904: "RENDERER_ID": invalid identifier
    Please note that we are migrating from ATG 2007 to ATG 10.0.1...Also we are doing deployment in this new environment for the first time only.
    Thanks a lot
    Pijush

    Hi Pijush,
    The exception towards the end of the stack trace says the RENDERER_ID is an invalid identifier. the Oracle error 00904 indicates the column name must be wrong. Can you verify the repostiory xml on the BlockRepository and check the column name.
    Regards,
    Srikanth

  • I am trying to create a community addition, but just keep getting *Error occurred while saving your data.

    I am trying to create a community addition, but just keep getting   *Error occurred while saving your data.
    Trying to add the following community addtion for:     http://technet.microsoft.com/en-us/library/cc755631(v=ws.10).aspx
    In the above website do NOT copy the command, you have to type it in.  Webpage Error.
    You can use both    dsquery server –hasfsmo schema    and    dsquery server -forest –hasfsmo schema
    The problem is, I believe, a hidden character in the command on this webpage which follows the Paste function and results in the error Unknown Parameter error.

    Hi John,
    You might have better luck posting this in the library feedback forum here:
    http://social.msdn.microsoft.com/Forums/en-us/home?forum=libraryfeedback&filter=alltypes&sort=lastpostdesc
    It seems odd to me that the TechNet library feedback forum lives under the MSDN branding, but that seems to be the case.
    Don't retire TechNet! -
    (Don't give up yet - 12,575+ strong and growing)

Maybe you are looking for